- Aug 07, 2018
-
-
Troy Kisky authored
nitrogen6_vm: prefer hannstar7 over lg1280x800 nitrogen6_vm: add IMX_VD38_AUO_B101EW05 nitrogen6_vm: add IMX_VD38_DT070BTFT nitrogen6_vm.h: CONFIG_IPUV3_CLK 264000000 nitrogen6_vm: setup_dispay is done in fbpanel nitrogen6_vm: add CONFIG_CMD_GPIO nitrogen6_vm: explicit fbp_detect_i2c nitrogen6_vm: use boundary.h nitrogen6_vm: setup rgb_gpio_pads in board_early_init_f nitrogen6_vm: change sdcard drive strength nitrogen6_vm: add CONFIG_SPI_FLASH_SPANSION nitrogen6_vm: change sdcard drive strength(partial revert) nitrogen6_vm: add nitrogen6_vm-pt1g_defconfig nitrogen6_vm: nitrogen6_vm_defconfig add CONFIG_BLOCK_CACHE nitrogen6_vm: use common code for eth init nitrogen6_vm: eth.c now in common directory nitrogen6_vm: move misc_init_r/do_kbd to common nitrogen6_vm: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nitrogen6_vm: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nitrogen6_vm: use CONFIG_DEFAULT_HITACHI_HVGA nitrogen6_vm: use common ddr scripts nitrogen6_vm: port to v2018.07 Signed-off-by:
Troy Kisky <troy.kisky@boundarydevices.com> nitrogen6_vm.h: add basic fastboot support Only works on eMMC with GPT already present. nitrogen6_vm: add secure boot option nitrogen6_vm: update to v2017.01 nitrogen6_vm: update to v2017.03 Signed-off-by:
Gary Bisson <gary.bisson@boundarydevices.com>
-
Troy Kisky authored
nitrogen6_som2: add IMX_VD38_AUO_B101EW05 nitrogen6_som2: add IMX_VD38_DT070BTFT nitrogen6_som2: calibrate 1G boards, sample size of only 4 nitrogen6_som2: nitrogen6q_som2_4g.cfg: remove redefine of CONFIG_MX6Q nitrogen6_som2: disable mirroring nitrogen6_som2: 4G calibration nitrogen6_som2: add atheros AR8035 ethernet phy choice nitrogen6_som2: increase drive strength for usdhc2/3, sd card/wifi nitrogen6_som2.h: CONFIG_IPUV3_CLK 264000000 nitrogen6_som2: use nitrogen6x clocks.cfg/ddr-setup.cfg nitrogen6_som2: explicit fbp_detect_i2c nitrogen6_som2: add wlmac nitrogen6_som2: verify port in board_ehci_hcd_init nitrogen6_som2: use boundary.h nitrogen6_som2: setup rgb_gpio_pads in board_early_init_f nitrogen6_som2: add CONFIG_SPI_FLASH_SPANSION nitrogen6q_som2: add CONFIG_CMD_GPIO nitrogen6q_som2: rename some cfg files nitrogen6_som2: add nitrogen6_som2_s512m_defconfig nitrogen6_som2: add nitrogen6_som2_s1g_defconfig nitrogen6_som2: nitrogen6_som2_s1g_defconfig add CONFIG_BLOCK_CACHE nitrogen6_som2: use common code for eth init nitrogen6_som2: eth.c now in common directory nitrogen6_som2: move misc_init_r/do_kbd to common nitrogen6_som2: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nitrogen6_som2: use common 1066mhz_4x256mx16.cfg nitrogen6_som2: use common 1066mhz_4x128mx16.cfg nitrogen6_som2: use common 800mhz_4x128mx16.cfg nitrogen6_som2: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nitrogen6_som2: fix DEFCONFIG nitrogen6qp_som2_4g nitrogen6_som2: 800mhz_2x128mx16.cfg: remove _P1 accesses nitrogen6_som2: 800mhz_2x256mx16.cfg: remove _P1 accesses nitrogen6_som2: 800mhz_2x128mx16.cfg: use common values CFG0: 0x40435323 to 0x3f435333 tRFC - 65 to 64 clocks tFAW - 19 to 20 clocks CFG1: 0xB66E8D63 to 0xb68e8b63 tRC from 20 to 21 clocks tWR from 7 to 6 clocks MR0: 0x13208030 to 0x15208030 tWR from 5 to 6 clocks nitrogen6_som2: 800mhz_2x256mx16.cfg: :use common values MDCFG0: from 0x696c5323 to 0x666a5333 tRFC - from 106 to 103 clocks tXS - from 109 to 107 clocks tFAW - from 19 to 20 clocks MDCFG1: from 0xb66e8d63 to 0xb68e8b63 tRC - from 20 to 21 clocks tWR - from 7 clocks to 6 clocks MDCFG2: from 0x01ff00dc to 0x01ff00db tRRD from 5 to 4 clocks MDRWD: from 0x000026d2 to 0x0f9f26d2 restore unused field to default value MDOR: from 0x006c1023 to 0x006a1023 tXPR - from 109 to 107 clocks MR0: from 0x13208030 to 0x15208030 tWR - from 5 to 6 clocks nitrogen6_som2: use common ddr scripts nitrogen6_som2: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
nitrogen6_scm: setup rgb_gpio_pads in board_early_init_f nitrogen6_scm: nitrogen6_scm_defconfig add CONFIG_BLOCK_CACHE nitrogen6_scm: use common code for eth init nitrogen6_scm: eth.c now in common directory nitrogen6_scm: move misc_init_r/do_kbd to common nitrogen6_scm: move max77823_init to common nitrogen6_scm: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nitrogen6_scm: normal display support nitrogen6_scm: change # of mmc/sdcards to 1 nitrogen6_scm: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nitrogen6_scm: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
nitrogen6qp_max_defconfig: add imx6qp specific ddr calibration nitrogen6qp_max4g.cfg: add Noc DDR configuration register set nitrogen6qp_max4g.cfg: change IPU priorities for imx6qp nitrogen6_max: prefer hannstar7 over lg1280x800 nitrogen6_max: add IMX_VD38_AUO_B101EW05 nitrogen6_max: add IMX_VD38_DT070BTFT nitrogen6_max: add IMX_VD_LD070WSVGA nitrogen6_max: add IMX_VD38_TM070JDHG30 nitrogen6_max: add IMX_VD_1080P60_J (jeida 1080p dual lvds) nitrogen6_max.h: CONFIG_IPUV3_CLK 264000000 nitrogen6_max: use GP_KSZ9021_xx for KSZ9021 strapping Ready for changing to atheros phy. nitrogen6_max: use nitrogen6x clocks.cfg/ddr-setup.cfg nitrogen6qp_max4g.cfg: Noc DDR config done in ddr-setup now nitrogen6_max4g.cfg: add support for iMX6QP nitrogen6qp_max4g.cfg: use nitrogen6_max4g.cfg instead nitrogen6_max: add CONFIG_CMD_GPIO nitrogen6_max: fix GP_BACKLIGHT_LVDS2 nitrogen6_max.h: make more like nitrogen6x.h nitrogen6_max: explicit fbp_detect_i2c nitrogen6_max: add wlmac nitrogen6_max: verify port in board_ehci_hcd_init nitrogen6_max: use boundary.h nitrogen6_max: add nitrogen6_max_4gr0_defconfig for 4G rank0 nitrogen6_max: setup rgb_gpio_pads in board_early_init_f nitrogen6_max: update comments in 1066mhz_4x512mx16.cfg nitrogen6_max: add nitrogen6_max_dl2g_defconfig nitrogen6_max: add nitrogen6_max_dl4g_defconfig nitrogen6_max: add CONFIG_SPI_FLASH_SPANSION nitrogen6_max: add VD_TFC_A9700LTWV35TC_C1 nitrogen6_max: add gt911 touch controller if serializer detected nitrogen6_max: add VD_TFC_A9700LTWV35TC_C1 for LVDS2 as well nitrogen6_max: add retries for i2c write failures nitrogen6_max: add ND-070PCAP-1024x600 nitrogen6_max: nitrogen6_max_defconfig add CONFIG_BLOCK_CACHE nitrogen6_max: use common code for eth init nitrogen6_max: eth.c now in common directory nitrogen6_max: move misc_init_r/do_kbd to common nitrogen6_max: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nitrogen6_max: add headphone det, drive mute low nitrogen6_max: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nitrogen6_max: fix DEFCONFIG nitrogen6_max_4gr0 nitrogen6_max: 800mhz_4x256mx16.cfg: use common values MDCFG0: from 0x686c5343 to 0x666a5333 tRFC - from 105 to 103 clocks tXS - from 109 to 107 clocks tFAW - from 21 to 20 clocks MDCFG1: from 0xb68f8d63 to 0xb68e8b63 tRAS - from 16 to 15 clocks tWR - from 7 clocks to 6 clocks MDCFG2: from 0x01ff00dc to 0x01ff00db tRRD from 5 to 4 clocks MDRWD: from 0x000026d2 to 0x0f9f26d2 restore unused field to default value MDOR: from 0x006c1023 to 0x006a1023 tXPR - from 109 to 107 clocks MR0: from 0x17208030 to 0x15208030 tWR - from 7 to 6 clocks nitrogen6_max: 800mhz_4x512mx16.cfg: use common values MDCFG0: from 0x686c5343 to 0x666a5343 tRFC - from 105 to 103 clocks tXS - from 109 to 107 clocks MDCFG1: from 0xb68f8d63 to 0xb68e8b63 tRAS - from 16 to 15 clocks tWR - from 7 clocks to 6 clocks MDRWD: from 0x000026d2 to 0x0f9f26d2 restore unused field to default value MDOR: from 0x006c1023 to 0x006a1023 tXPR - from 109 to 107 clocks MR0: from 0x17208030 to 0x15208030 tWR - from 7 to 6 clocks nitrogen6_max: use common ddr scripts nitrogen6_max: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
nitrogen51_vm: add OKAYA_480_272 support nitrogen51_vm: change I2C2 pullup to 47K nitrogen51_vm: nitrogen51_vm_256m_defconfig add CONFIG_BLOCK_CACHE nitrogen51_vm_512m: nitrogen51_vm_512m_defconfig add CONFIG_BLOCK_CACHE nitrogen51_vm: use internal IPU clock for hvga as default nitrogen51_vm: use common code for eth init nitrogen51_vm: eth.c now in common directory nitrogen51_vm: move misc_init_r/do_kbd to common nitrogen51_vm: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nitrogen51_vm: swap GPIOKEYS/LEDS pins nitrogen51_vm: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nitrogen51_vm: use 32K clock, otherwise clock ticks too fast nitrogen51_vm: initialize more pins, turn off ov5642 nitrogen51_vm: add comment for ddr nitrogen51_vm: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
nitrogen51_e: MAINTAINERS: s/NITROGEN6_VM/NITROGEN6_E/ nitrogen51_e: add comment for ddr nitrogen51_e: port to v2018.07 Signed-off-by: -
Troy Kisky authored
Includes nit6xlite and nit6xlite1g nit6xlite: add ASIT500MA6F5D nit6xlite: add CONFIG_IMX_HDMI nit6xlite: add HANNSTAR7/LG1280_800/SHARP_LQ101K1LY04 nit6xlite: add IMX_VD38_AUO_B101EW05 nit6xlite: add IMX_VD38_DT070BTFT nit6xlite.h: CONFIG_IPUV3_CLK 264000000 nit6xlite: setup_dispay is done in fbpanel nit6xlite.h: add basic fastboot support nit6xlite: add CONFIG_CMD_GPIO nit6xlite.c: explicit fbp_detect_i2c nit6xlite: add bd_addr bluetooth mac environment variable nit6xlite: verify fuse blown before setting wlmac nit6xlite: verify fuse blown before setting bd_addr nit6xlite: verify port in board_ehci_hcd_init nit6xlite: use boundary.h nit6xlite: add splash screen support nit6xlite: setup remaining pins nit6xlite: increase sd card drive strength nit6xlite: add secure boot option nit6xlite: add CONFIG_SPI_FLASH_SPANSION nit6xlite: nit6xlite_defconfig add CONFIG_BLOCK_CACHE nit6xlite1g: nit6xlite1g_defconfig add CONFIG_BLOCK_CACHE nit6xlite: use common code for eth init nit6xlite: eth.c now in common directory nit6xlite: move misc_init_r/do_kbd to common nit6xlite: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nit6xlite: mute becomes CEC nit6xlite: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nit6xlite: use common ddr scripts nit6xlite: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
neol: move misc_init_r/do_kbd to common neol: eth.c now in common directory neol: initialize GP_5V_DLP_EN low neol: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common Revert "neol: initialize GP_5V_DLP_EN low" neol: use EIM_DA7 as GP_5V_DLP_EN neol: use common 1066mhz_4x256mx16.cfg neol: leave GP_5V_DLP_EN high for early boards neol: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs neol: drive GP_5V_DLP_EN_REV0 high, don't rely on pull-up neol: use common ddr script neol: port to v2018.07 Signed-off-by:
Stefan Becker <sbecker@neolitics.com>
-
Troy Kisky authored
mx6_r.h: CONFIG_IPUV3_CLK 264000000 mx6_r: add CONFIG_CMD_GPIO mx6_r: explicit fbp_detect_i2c mx6_r: use VDF_LB043 mx6_r: verify port in board_ehci_hcd_init mx6_r: use boundary.h mx6_r: setup rgb_gpio_pads in board_early_init_f mx6_r: add CONFIG_SPI_FLASH_SPANSION mx6_r: mx6_r_defconfig add CONFIG_BLOCK_CACHE mx6_r: use common code for eth init mx6_r: eth.c now in common directory mx6_r: move misc_init_r/do_kbd to common mx6_r: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common mx6_r: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs mx6_r: add mx6_r_q2g.cfg mx6_r: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
mtp.h: CONFIG_IPUV3_CLK 264000000 mtp: use nitrogen6x clocks.cfg/ddr-setup.cfg mtp: add CONFIG_CMD_GPIO mtp: add usbh2 strobe/data mtp: add cmd_custom, to avoid upgrade message mtp: add imx6QP, mtp_qp_defconfig mtp: add wlmac from fuses mtp: s/mac/mac_address/ for consistency mtp: use boundary.h mtp: add 2g config option mtp: add CONFIG_SPI_FLASH_SPANSION mtp: change i2c drive strength to avoid undershoot mtp: s/PAD_CTL_DSE_90ohm/PAD_CTL_DSE_80ohm/ to fix compile error mtp: gadget mac is in ethaddr not eth1addr, because no FEC mtp: update 2G quadplus calibration based on 15 boards mtp: mtp_defconfig add CONFIG_BLOCK_CACHE mtp2g: mtp2g_defconfig add CONFIG_BLOCK_CACHE mtp2g_qp: mtp2g_qp_defconfig add CONFIG_BLOCK_CACHE mtp_qp: mtp_qp_defconfig add CONFIG_BLOCK_CACHE mtp: use common code for eth init mtp: eth.c now in common directory mtp: move misc_init_r/do_kbd to common mtp: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common mtp: use common 1066mhz_4x256mx16.cfg mtp: use common 1066mhz_4x128mx16.cfg mtp: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs mtp: spi: fix at45db041d mtp: use common ddr scripts mtp: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
med.h: CONFIG_IPUV3_CLK 264000000 med: add CONFIG_CMD_GPIO med: explicit fbp_detect_i2c med: use boundary.h med: add CONFIG_SPI_FLASH_SPANSION med: med_defconfig add CONFIG_BLOCK_CACHE med: use common code for eth init med: eth.c now in common directory med: move misc_init_r/do_kbd to common med: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common med: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs med: add med_q1g.cfg med: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
mcs: wait for panel to sync up before enabling backlight mcs: add display detection based on 4/5 wire touchscreen mcs: mcssolo1g_64bit.cfg: new calibration values mcs.h: CONFIG_IPUV3_CLK 264000000 mcs: setup_dispay is done in fbpanel mcs: documentation fix, GP_LVDS_DE_15_4 is unused mcs: add CONFIG_CMD_GPIO mcs: remove redundant CONFIG_CMD_GPIO mcs: explicit fbp_detect_i2c mcs: pass fbp_detect_gpio mcs: use VD_LD101WX1 mcs: verify port in board_ehci_hcd_init mcs: use boundary.h mcs: add CONFIG_SPI_FLASH_SPANSION mcs: mcsquad_defconfig add CONFIG_BLOCK_CACHE mcssolo1g_64bit: mcssolo1g_64bit_defconfig add CONFIG_BLOCK_CACHE mcssolo: mcssolo_defconfig add CONFIG_BLOCK_CACHE mcs: use common code for eth init mcs: eth.c now in common directory mcs: move misc_init_r/do_kbd to common mcs: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common mcs: use common 1066mhz_4x256mx16.cfg mcs: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs mcs: use common 800mhz_4x128mx16.cfg mcs: use common ddr scripts mcs: port to v2018.07 Signed-off-by:
Laci Tele <laci@boundarydevices.com> mcs: update to v2017.01 mcs: update to v2017.03 Signed-off-by:
-
Troy Kisky authored
ltch: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
lshore: fix default environment lshore: update to v2017.01 lshore: add missing wlmac address setup lshore: add pin definitions for rev1.1 lshore: update to v2017.03 Signed-off-by:
-
Troy Kisky authored
ls.h: CONFIG_IPUV3_CLK 264000000 ls: use nitrogen6x/ddr-setup.cfg ls: add CONFIG_CMD_GPIO ls: explicit fbp_detect_i2c ls: add wlmac ls: use boundary.h ls: add CONFIG_SPI_FLASH_SPANSION ls: ls_defconfig add CONFIG_BLOCK_CACHE ls: use common code for eth init ls: eth.c now in common directory ls: move misc_init_r/do_kbd to common ls: move max77823_init to common ls: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common ls: use common 1066mhz_4x256mx16.cfg ls: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs ls: use common ddr script ls: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
jlm.h: CONFIG_IPUV3_CLK 264000000 jlm: emmc is mmc 1, sdcard is mmc 0 jlm: add CONFIG_CMD_GPIO jlm: add jlm_2g_defconfig jlm: explicit fbp_detect_i2c jlm: add wlmac jlm: verify port in board_ehci_hcd_init jlm: use boundary.h jlm: setup rgb_gpio_pads in board_early_init_f jlm: add CONFIG_SPI_FLASH_SPANSION jlm: jlm_1g_defconfig add CONFIG_BLOCK_CACHE jlm_2g: jlm_2g_defconfig add CONFIG_BLOCK_CACHE jlm: use common code for eth init jlm: eth.c now in common directory jlm: move misc_init_r/do_kbd to common jlm: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common jlm: use common 1066mhz_4x256mx16.cfg jlm: use common 1066mhz_4x128mx16.cfg jlm: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs jlm: use common ddr scripts jlm: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
ioc: only pwm1 for all backlights ioc: prefer hannstar7 over lg1280x800 ioc: add IMX_VD38_AUO_B101EW05 ioc.h: CONFIG_IPUV3_CLK 264000000 ioc: add CONFIG_CMD_GPIO ioc: explicit fbp_detect_i2c ioc: add wlmac ioc: verify port in board_ehci_hcd_init ioc: use boundary.h ioc: setup rgb_gpio_pads in board_early_init_f ioc: add CONFIG_SPI_FLASH_SPANSION ioc: ioc_defconfig add CONFIG_BLOCK_CACHE ioc: use common code for eth init ioc: eth.c now in common directory ioc: move misc_init_r/do_kbd to common ioc: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common ioc: use common 1066mhz_4x128mx16.cfg ioc: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs ioc: use common ddr script ioc: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
insp: enable both hdmi/lcd with LSA40AT9001 resolution insp.h: CONFIG_IPUV3_CLK 264000000 insp: use nitrogen6x clocks.cfg/ddr-setup.cfg insp: add 1g memory configuration insp: calibrate 1G memory, (15 board sample size) insp: set wlmac insp: add environment variables allow_noncea=1;bootdelay=1;preboot;splashsize insp: add CONFIG_CMD_GPIO insp: remove FEC config options, no fec on board insp: explicit fbp_detect_i2c insp: s/mac/mac_addres/ for consistentcy insp: use boundary.h insp: setup rgb_gpio_pads in board_early_init_f insp: add CONFIG_SPI_FLASH_SPANSION insp: insp_defconfig add CONFIG_BLOCK_CACHE insp2g: insp2g_defconfig add CONFIG_BLOCK_CACHE insp: add splashimage to prevent data abort on preboot insp: use common code for eth init insp: eth.c now in common directory insp: move misc_init_r/do_kbd to common insp: remove code for non-existent max77823 chip insp: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common insp: no functional change, move pads in list, add comment insp: use common 1066mhz_4x256mx16.cfg insp: use common 1066mhz_4x128mx16.cfg insp: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs insp: use common ddr scripts insp: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
hp: add VD_AFK1024600A02 hp: add tx enable for rs485 hp: add CONFIG_SPI_FLASH_SPANSION hp: initialize otg network always hp: add hp_s512m_defconfig hp: hp_defconfig add CONFIG_BLOCK_CACHE hp_s512m: hp_s512m_defconfig add CONFIG_BLOCK_CACHE hp: add hp_q1g_defconfig hp: use common code for eth init hp: eth.c now in common directory hp: move misc_init_r/do_kbd to common hp: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common hp: use common 1066mhz_4x128mx16.cfg hp: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs hp: 800mhz_2x128mx16.cfg: remove _P1 accesses hp: 800mhz_2x128mx16.cfg: use common values CFG0: 0x40435323 to 0x3f435333 tRFC - 65 to 64 clocks tFAW - 19 to 20 clocks CFG1: 0xB66E8D63 to 0xb68e8b63 tRC from 20 to 21 clocks tWR from 7 to 6 clocks MR0: 0x13208030 to 0x15208030 tWR from 5 to 6 clocks hp: use common ddr scripts hp: check otg_power_detect before enabling otg_vbus hp: ensure otg cable not connected before allowing boot hp: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
hl: set wlmac for TiWi hl: use common code for eth init hl: eth.c now in common directory hl: move misc_init_r/do_kbd to common hl: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common hl: default to tm070jdhg30 instead of hannstar7 hl: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs hl: 800mhz_2x256mx16.cfg: remove _P1 accesses hl: 800mhz_2x256mx16.cfg: use common values MDCFG2: from 0x01FF0093 to 0x01FF00db tRTP - from 3 to 4 clocks (4 is minimum allowed) tWTR - from 3 to 4 clocks (4 is minimum allowed) MR0: from 0x13208030 to 0x15208030 tWR - from 5 to 6 clocks hl: use common ddr script hl: port to v2018.07 Signed-off-by: -
Troy Kisky authored
h4: fix on/off levels h4.h: CONFIG_IPUV3_CLK 264000000 h4: add CONFIG_CMD_GPIO h4: explicit fbp_detect_i2c h4: use boundary.h h4: setup rgb_gpio_pads in board_early_init_f h4: add CONFIG_SPI_FLASH_SPANSION h4: h4_defconfig add CONFIG_BLOCK_CACHE h4: use common code for eth init h4: eth.c now in common directory h4: move misc_init_r/do_kbd to common h4: move max77823_init to common h4: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common h4: use common 1066mhz_4x256mx16.cfg h4: KEY_COL0 must be UART4_TX_DATA h4: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs h4: use common ddr script h4: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
Includes hsolo1g and hquad2g h.h: CONFIG_IPUV3_CLK 264000000 h: setup_dispay is done in fbpanel h: add CONFIG_CMD_GPIO h: explicit fbp_detect_i2c h: verify port in board_ehci_hcd_init h: use boundary.h h: setup rgb_gpio_pads in board_early_init_f h: add CONFIG_SPI_FLASH_SPANSION h: hquad2g_defconfig add CONFIG_BLOCK_CACHE hsolo1g: hsolo1g_defconfig add CONFIG_BLOCK_CACHE h: use common code for eth init h: eth.c now in common directory h: move misc_init_r/do_kbd to common h: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common h: use common 1066mhz_4x256mx16.cfg h: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs h: use common ddr scripts h: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
eo: add eo_duallite_defconfig eo.h: CONFIG_IPUV3_CLK 264000000 eo: use nitrogen6x/ddr-setup.cfg eo: use MX6Q or MX6DL instead of MX6QDL eo: add CONFIG_CMD_GPIO eo: explicit fbp_detect_i2c eo: add wlmac eo: use boundary.h eo: add CONFIG_SPI_FLASH_SPANSION eo: eo_defconfig add CONFIG_BLOCK_CACHE eo_duallite: eo_duallite_defconfig add CONFIG_BLOCK_CACHE eo: use common code for eth init eo: eth.c now in common directory eo: move misc_init_r/do_kbd to common eo: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common eo: use common 1066mhz_4x128mx16.cfg eo: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs eo: use common ddr scripts eo: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
dash.h: CONFIG_IPUV3_CLK 264000000 dash: add CONFIG_CMD_GPIO dash: explicit fbp_detect_i2c dash: verify port in board_ehci_hcd_init dash: use boundary.h dash: add CONFIG_SPI_FLASH_SPANSION dash: dash_defconfig add CONFIG_BLOCK_CACHE dash: use common code for eth init dash: eth.c now in common directory dash: move misc_init_r/do_kbd to common dash: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common dash: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs dash: add dash_q1g.cfg dash: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
cob2: 9 board sample for q1g ddr calibration cob2: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs cob2: use common ddr script cob2: port to v2018.07 Signed-off-by: -
Troy Kisky authored
cob.h: CONFIG_IPUV3_CLK 264000000 cob: use nitrogen6x/ddr-setup.cfg cob: add CONFIG_CMD_GPIO cob: explicit fbp_detect_i2c cob: verify port in board_ehci_hcd_init cob: use boundary.h cob: setup rgb_gpio_pads in board_early_init_f cob: add CONFIG_SPI_FLASH_SPANSION cob.h: skip fuses, they do it themselves cob: cob_defconfig add CONFIG_BLOCK_CACHE cob: use common code for eth init cob: eth.c now in common directory cob: move misc_init_r/do_kbd to common cob: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common cob: use common 1066mhz_4x128mx16.cfg cob: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs cob: use common ddr script cob: port to v2018.07 Signed-off-by:
-
Gary Bisson authored
cnt: add defconfig for 1GB of RAM version cnt: fix boot devs configuration cnt: update to v2017.01 cnt: update to v2017.03 cnt.h: add custom BOOT_TARGET_DEVICES priority Signed-off-by:
-
Troy Kisky authored
cid_tab: delay 3P7V rail turn on cid_tab: turn off boost before poweroff cid_tab: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs cid_tab: tamper support checking TAMPER pin cid_tab: use common ddr script cid_tab: port to v2018.07 Signed-off-by:
-
Gary Bisson authored
cid_2g_defconfig: reduce bootdelay to 0 cid: limit boot sequence to eMMC cid: start fastboot when power and reset are pressed Signed-off-by:
-
Troy Kisky authored
cad.h: CONFIG_IPUV3_CLK 264000000 cad: add CONFIG_CMD_GPIO cad: explicit fbp_detect_i2c cad: use VDF_SPI_QVGA cad: use boundary.h cad: setup rgb_gpio_pads in board_early_init_f cad: add CONFIG_SPI_FLASH_SPANSION cad: cad_defconfig add CONFIG_BLOCK_CACHE cad: use common code for eth init cad: eth.c now in common directory cad: move misc_init_r/do_kbd to common cad: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common cad: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs cad: use common ddr script cad: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
bt2: GPS is thru i2c now bt2: swap J6/J7 bt2: rename J6/J7 - J5V/J12v bt2: use nitrogen6x clock.cfg/ddr-setup.cfg bt2: 1066mhz_4x512mx16.cfg, remove confusing comment bt2: add/use 1066mhz_4x512mx16-r0.cfg for 4G memory option bt2: add CONFIG_CMD_GPIO bt2: explicit fbp_detect_i2c bt2: add wlmac bt2: increase refresh rate for 4G-rank0 bt2: setup rgb_gpio_pads in board_early_init_f bt2: add CONFIG_SPI_FLASH_SPANSION bt2: bt2_2g_defconfig add CONFIG_BLOCK_CACHE bt2_4g: bt2_4g_defconfig add CONFIG_BLOCK_CACHE bt2: use common code for eth init bt2: eth.c now in common directory bt2: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common bt2: use common 1066mhz_4x256mx16.cfg bt2: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs bt2: use common ddr scripts bt2: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
Two configurations bt2g and bt4g for two different memory layouts bt.h: CONFIG_IPUV3_CLK 264000000 bt: rename J6/J7 to J12V/J5V bt: use nitrogen6x clock.cfg/ddr-setup.cfg bt: add CONFIG_CMD_GPIO bt: explicit fbp_detect_i2c bt: use boundary.h bt: add CONFIG_SPI_FLASH_SPANSION bt.h: use BD_CMA to specify cma= on cmd_line bt: bt2g_defconfig add CONFIG_BLOCK_CACHE bt4g: bt4g_defconfig add CONFIG_BLOCK_CACHE bt: use common code for eth init bt: eth.c now in common directory bt: move misc_init_r/do_kbd to common bt: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common bt: use common 1066mhz_4x256mx16.cfg bt: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs bt: use common ddr scripts bt: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
ash2: KEY_COL0 must be UART4_TX_DATA ash2: add power_init_board because mdelay cannot be used in board_early_init_f ash2: use common 800mhz_4x128mx16.cfg, and calibrate ddr ash2: rgb24 vs rgb66 panel have different backlight active levels ash2: fixup dtb backlight levels ash2: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs ash2: use common ddr script ash2: port to v2018.07 Signed-off-by: -
Troy Kisky authored
ash: add poweroff command ash: fix some input gpios(CH_ON_RBL/SG_ON_RBL/DOOR_CLOSED ash: use nitrogen6x/clock.cfg ash: use nitrogen6x ddr-setup.cfg ash: remove micrel phy references(only atheros on this board) ash: add CONFIG_CMD_GPIO ash: set rgb_gpio_pads ash: TP86 becomes lvds backlight enable ash: explicit fbp_detect_i2c ash: default uart1 to rs232 ash: use 800mhz for memory ash: use boundary.h ash: GP_BSL_CB_ON_OFF high, TX23D200_18 default dispay ash: add CONFIG_VIDEO_SKIP_VERSION ash: GP_BSL_CB_ON_OFF default to low again ash: add EIM_EB2 for sd card power control ash: add CONFIG_SPI_FLASH_SPANSION ash: ash_defconfig add CONFIG_BLOCK_CACHE ash: use common code for eth init ash: eth.c now in common directory ash: move misc_init_r/do_kbd to common ash: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common ash: gpio3 is power off, don't redefine ash: add power_init_board because mdelay cannot be used in board_early_init_f ash: use common 800mhz_4x128mx16.cfg ash: rgb24 vs rgb66 panel have different backlight active levels ash: fixup dtb backlight levels ash: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs ash: use common ddr script ash: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
ap: forgot file include/configs/ap.h ap: ap_q2g_defconfig: add CONFIG_SPI_FLASH_GIGADEVICE ap: add bootscript_lp8860_eprom.txt ap: add verification to bootscript_lp8860_eprom.txt ap: use common ddr script ap: port to v2018.07 Signed-off-by: -
Gary Bisson authored
acl: update to v2017.01 acl update to v2017.03 acl: fix scanner gpios initialization Signed-off-by:
-
Gary Bisson authored
ys: update to v2017.01 ys: update to v2017.03 Signed-off-by:
-
Troy Kisky authored
a: add usb hub reset/uart3/uart4/flexcan pins a: keep USB Huawei Modem in reset a: add leds rx active/tx active a: remove printf of board_mmc_init a.h: add cmd_custom to avoid update u-boot warning a: add CONFIG_CMD_GPIO a: remove redundant CONFIG_CMD_GPIO a: verify port in board_ehci_hcd_init a: use boundary.h a: call preboot_keys a: add CONFIG_SPI_FLASH_SPANSION a: add RV4162 rtc on I2C2 a: a_defconfig add CONFIG_BLOCK_CACHE a: use common code for eth init a: eth.c now in common directory a: move misc_init_r/do_kbd to common a: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common a: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs a: add a_s512m.cfg a: port to v2018.07 Signed-off-by:
-
Troy Kisky authored
nitrogen6x: delay before enabling backlight spi_display: set mosi as write in enable_spi_rgb nitrogen6x: add IMX_VD_A030JN01_YUV720 nitrogen6x: add hdmi vga mode nitrogen6x: add hdmi 480p 6x_bootscript-ubuntu-3.14.txt: add imx7d support 6x_bootscript-yocto-3.14.txt: add imx7d support nitrogen6x: prefer hannstar7 over lg1280x800 nitrogen6x: initialize GP_USB_HUB_RESET as low output nitrogen6x: add IMX_VD38_AUO_B101EW05 nitrogen6x: add IMX_VD38_DT070BTFT nitrogen6x: support AR8035 phy as well Needed for new carrier with old SOM cpu card. nitrogen6x: add CONFIG_PHY_ATHEROS nitrogen6x: EIM_D29 high for new carrier with old som 6x_bootscript-ubuntu-3.14.txt: add rw if not using initrd nitrogen6x: add IMX_VD38_TM070JDHG30 nitrogen6x.h: CONFIG_IPUV3_CLK 264000000 nitrogen6x: add imx6qp support for ipu priorities nitrogen6x: ddr-setup.cfg: disable mirroring ddr-setup.cfg: add IMX6QP support nitrogen6x: spacing changes in environment variables nitrogen6x: explicit fbp_detect_i2c nitrogen6x: net_upgradeu.txt initial addition nitrogen6x: net_upgrade_fs.txt initial addition nitrogen6x: ubuntu/yocto add bd_addr for bluetooth mac to 6x_bootscript nitrogen6x: add wlmac nitrogen6x: add wlmac nitrogen6x: verify port in board_ehci_hcd_init nitrogen6x: use boundary.h nitrogen6x: setup rgb_gpio_pads in board_early_init_f nitrogen6x: add VD_KD024FM nitrogen6x: s/board_enable_spi_rgb/board_pre_enable/ nitrogen6x: add CONFIG_SPI_FLASH_SPANSION boundary.h: common include file initial commit boundary: separate bootcmd so it can be overridden 6x_bootscript-ubuntu-3.14.txt: add Laci's changes(cpu/board/bootpart) and nomsi 6x_bootscript-yocto-3.14.txt: add Laci's changes(cpu/board/bootpart) and nomsi net_upgrade_fs.txt: s/dhcp/tftp/ since ipaddr is already valid net_upgradeu.txt: s/dhcp/tftp/ since ipaddr is already valid 6x_bootscript-*-3.14.txt: s/enable_msi/disable_msi/ 6x_bootscript-*-3.14.txt: set bootargs after importing environment variable, as it may reset bootargs net_upgrade_fs.txt: grab decompressed size from end of file net_upgrade_fs: restructure to avoid using exit net_upgradeu: remove offset and friends from environment net_upgradeu_fs: initial addition boundary: allow override of CONFIG_SF_DEFAULT_CS, make fastboot conditional on CONFIG_CI_UDC boundary: add loglevel= environment variable boundary: add cma= option 6x_upgrade.txt: MX25L6405D has 64k erase size net_upgradeu.txt: MX25L6405D has 64k erase size 6x_upgrade.txt: add mx51 support 6x_bootscript*.txt: add i.mx51/i.mx53 support net_upgrade*.txt: add i.mx51/i.mx53 support 6x_bootscript-ubuntu-3.14.txt: add loglevel 6x_bootscript-yocto-3.14.txt: add loglevel 6x_bootscript-mainline.txt: add loglevel 6x_bootscript-mainline.txt: add reset_cause 6x_bootscript-ubuntu-3.14.txt: add reset_cause 6x_bootscript-yocto-3.14.txt: add reset_cause 6x_bootscript-ubuntu-3.14.txt: add run cmd_lcd2 6x_bootscript-yocto-3.14.txt: add run cmd_lcd2 6x_upgrade: add qspi support for Nitrogen7 6x_upgrade: add qspi file checks size/tag 6x_upgrade.txt: use sfname to burn correct qspi paramter file nitrogen6q_fl: add CONFIG_CMD_GPIO configs: boundary: add imx51 specifics ddr-setup.cfg: increase WALAT to 1 cycle include/configs/boundary.h: good default for BD_CONSOLE boundary: add fuse config needed for boards nitrogen6x: add script linking via next variable/prog_fuses boundary.h: allow skipping fuses nitrogen6x: nitrogen6q_defconfig add CONFIG_BLOCK_CACHE nitrogen6x: add CONFIG_BLOCK_CACHE to defconfigs boundary.h: add support for i.mx53 boundary: fix CONFIG_IPUV3_CLK for imx51/imx53 boundary.h: fix build warnings when HAB enabled nitrogen6dl2g_defconfig: remove extra define of CONFIG_SYS_EXTRA_OPTIONS boundary: fix CONFIG_ETHPRIME(FEC0) for imx6sx boundary: add eth.c/padctrl.h nitrogen6x: use common code for eth init nitrogen6x: add CONFIG_SYS_BOARD_MULTIPLE to defconfigs boundary: eth: use mask to compare ksz9021 boundary: move eth.c to common directory nitrogen6x: eth.c now in common directory nitrogen6x: move misc_init_r/do_kbd to common nitrogen6x: remove CONFIG_SYS_BOARD_MULTIPLE use undef CONFIG_SYS_BOARD instead nitrogen6x: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nitrogen6x: const i2c_pads_info nitrogen6x: use common 1066mhz_4x256mx16.cfg nitrogen6x: use common 1066mhz_4x128mx16.cfg nitrogen6x: use common 800mhz_4x128mx16.cfg nitrogen6x: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nitrogen6x: 800mhz_2x128mx16.cfg: remove _P1 accesses nitrogen6x: 800mhz_2x256mx16.cfg: remove _P1 accesses nitrogen6x: 800mhz_2x128mx16.cfg: use common values CFG0: 0x40435323 to 0x3f435333 tRFC - 65 to 64 clocks tFAW - 19 to 20 clocks CFG1: 0xB66E8D63 to 0xb68e8b63 tRC from 20 to 21 clocks tWR from 7 to 6 clocks MR0: 0x13208030 to 0x15208030 tWR from 5 to 6 clocks nitrogen6x: 800mhz_2x256mx16.cfg: use common values MDCFG0: from 0x696c5323 to 0x666a5333 tRFC - from 106 to 103 clocks tXS - from 109 to 107 clocks tFAW - from 19 to 20 clocks MDCFG1: from 0xb66e8d63 to 0xb68e8b63 tRC - from 20 to 21 clocks tWR - from 7 clocks to 6 clocks MDRWD: from 0x000026d2 to 0x0f9f26d2 restore unused field to default value MDOR: from 0x006c1023 to 0x006a1023 tXPR - from 109 to 107 clocks MR0: from 0x13208030 to 0x15208030 tWR - from 5 to 6 clocks nitrogen6x: 800mhz_4x256mx16.cfg: use common values MDCFG0: from 0x696c5323 to 0x666a5333 tRFC - from 106 to 103 clocks tXS - from 109 to 107 clocks tFAW - from 19 to 20 clocks MDCFG1: from 0xb66e8d63 to 0xb68e8b63 tRC - from 20 to 21 clocks tWR - from 7 clocks to 6 clocks MDRWD: from 0x000026d2 to 0x0f9f26d2 restore unused field to default value MDOR: from 0x006c1023 to 0x006a1023 tXPR - from 109 to 107 clocks MR0: from 0x13208030 to 0x15208030 tWR - from 5 to 6 clocks nitrogen6x: use common ddr scripts nitrogen6x: port to v2018.07 nitrogen6x: add VD_DT035BTFT panel Signed-off-by:
Ian Coolidge <ian@boundarydevices.com> 6x_bootscript-mainline: switch to zImage booting nitrogen6x: add basic fastboot support 6x_bootscript-yocto-3.10.53: add Quad Plus dtb option nitrogen6x: declare TC358743 interrupt as input nitrogen6x.h: fixup update to v2017.01 boundary.h: increase fastboot buffer size boundary.h: add secure boot options boundary.h: fix USB host initialization 6x_bootscript-*-3.14.txt: add support for m4 specific dtb 6x_bootscript-mainline: update for new display configuration 6x_bootscript-mainline: switch to new panel naming 6x_bootscript-mainline: add support for BD070LIC2 6x_upgrade: re-introduce fs-specific load commands nitrogen6x: update to v2017.01 nitrogen6x: update to v2017.03 6x_bootscript-mainline: change default bootdir to be / boundary.h: add CONFIG_CMD_PART 6x_bootscript-mainline: fixup LVDS2 display handling 6x_bootscript-mainline: use UUID to identify root partition 6x_bootscript-mainline: introduce rfspart variable fixup boundary.h for 2017.07 boundary.h: use standard config_distro_bootcmd fixup 2 boundary.h for 2017.07 6x_bootscript-*-3.14.txt: add Silex mac address override support 6x_bootscript-yocto: remove obsolete commands 6x_bootscript-yocto: remove obsolete versions of script Signed-off-by:
-
Troy Kisky authored
Signed-off-by:
-
