- Aug 07, 2018
-
-
Troy Kisky authored
a: add usb hub reset/uart3/uart4/flexcan pins a: keep USB Huawei Modem in reset a: add leds rx active/tx active a: remove printf of board_mmc_init a.h: add cmd_custom to avoid update u-boot warning a: add CONFIG_CMD_GPIO a: remove redundant CONFIG_CMD_GPIO a: verify port in board_ehci_hcd_init a: use boundary.h a: call preboot_keys a: add CONFIG_SPI_FLASH_SPANSION a: add RV4162 rtc on I2C2 a: a_defconfig add CONFIG_BLOCK_CACHE a: use common code for eth init a: eth.c now in common directory a: move misc_init_r/do_kbd to common a: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common a: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs a: add a_s512m.cfg a: port to v2018.07 Signed-off-by:
Troy Kisky <troy.kisky@boundarydevices.com> a: update to v2017.01 a: update to v2017.03 a.h: add custom BOOT_TARGET_DEVICES priority Signed-off-by:
Gary Bisson <gary.bisson@boundarydevices.com>
-
Troy Kisky authored
nitrogen6x: delay before enabling backlight spi_display: set mosi as write in enable_spi_rgb nitrogen6x: add IMX_VD_A030JN01_YUV720 nitrogen6x: add hdmi vga mode nitrogen6x: add hdmi 480p 6x_bootscript-ubuntu-3.14.txt: add imx7d support 6x_bootscript-yocto-3.14.txt: add imx7d support nitrogen6x: prefer hannstar7 over lg1280x800 nitrogen6x: initialize GP_USB_HUB_RESET as low output nitrogen6x: add IMX_VD38_AUO_B101EW05 nitrogen6x: add IMX_VD38_DT070BTFT nitrogen6x: support AR8035 phy as well Needed for new carrier with old SOM cpu card. nitrogen6x: add CONFIG_PHY_ATHEROS nitrogen6x: EIM_D29 high for new carrier with old som 6x_bootscript-ubuntu-3.14.txt: add rw if not using initrd nitrogen6x: add IMX_VD38_TM070JDHG30 nitrogen6x.h: CONFIG_IPUV3_CLK 264000000 nitrogen6x: add imx6qp support for ipu priorities nitrogen6x: ddr-setup.cfg: disable mirroring ddr-setup.cfg: add IMX6QP support nitrogen6x: spacing changes in environment variables nitrogen6x: explicit fbp_detect_i2c nitrogen6x: net_upgradeu.txt initial addition nitrogen6x: net_upgrade_fs.txt initial addition nitrogen6x: ubuntu/yocto add bd_addr for bluetooth mac to 6x_bootscript nitrogen6x: add wlmac nitrogen6x: add wlmac nitrogen6x: verify port in board_ehci_hcd_init nitrogen6x: use boundary.h nitrogen6x: setup rgb_gpio_pads in board_early_init_f nitrogen6x: add VD_KD024FM nitrogen6x: s/board_enable_spi_rgb/board_pre_enable/ nitrogen6x: add CONFIG_SPI_FLASH_SPANSION boundary.h: common include file initial commit boundary: separate bootcmd so it can be overridden 6x_bootscript-ubuntu-3.14.txt: add Laci's changes(cpu/board/bootpart) and nomsi 6x_bootscript-yocto-3.14.txt: add Laci's changes(cpu/board/bootpart) and nomsi net_upgrade_fs.txt: s/dhcp/tftp/ since ipaddr is already valid net_upgradeu.txt: s/dhcp/tftp/ since ipaddr is already valid 6x_bootscript-*-3.14.txt: s/enable_msi/disable_msi/ 6x_bootscript-*-3.14.txt: set bootargs after importing environment variable, as it may reset bootargs net_upgrade_fs.txt: grab decompressed size from end of file net_upgrade_fs: restructure to avoid using exit net_upgradeu: remove offset and friends from environment net_upgradeu_fs: initial addition boundary: allow override of CONFIG_SF_DEFAULT_CS, make fastboot conditional on CONFIG_CI_UDC boundary: add loglevel= environment variable boundary: add cma= option 6x_upgrade.txt: MX25L6405D has 64k erase size net_upgradeu.txt: MX25L6405D has 64k erase size 6x_upgrade.txt: add mx51 support 6x_bootscript*.txt: add i.mx51/i.mx53 support net_upgrade*.txt: add i.mx51/i.mx53 support 6x_bootscript-ubuntu-3.14.txt: add loglevel 6x_bootscript-yocto-3.14.txt: add loglevel 6x_bootscript-mainline.txt: add loglevel 6x_bootscript-mainline.txt: add reset_cause 6x_bootscript-ubuntu-3.14.txt: add reset_cause 6x_bootscript-yocto-3.14.txt: add reset_cause 6x_bootscript-ubuntu-3.14.txt: add run cmd_lcd2 6x_bootscript-yocto-3.14.txt: add run cmd_lcd2 6x_upgrade: add qspi support for Nitrogen7 6x_upgrade: add qspi file checks size/tag 6x_upgrade.txt: use sfname to burn correct qspi paramter file nitrogen6q_fl: add CONFIG_CMD_GPIO configs: boundary: add imx51 specifics ddr-setup.cfg: increase WALAT to 1 cycle include/configs/boundary.h: good default for BD_CONSOLE boundary: add fuse config needed for boards nitrogen6x: add script linking via next variable/prog_fuses boundary.h: allow skipping fuses nitrogen6x: nitrogen6q_defconfig add CONFIG_BLOCK_CACHE nitrogen6x: add CONFIG_BLOCK_CACHE to defconfigs boundary.h: add support for i.mx53 boundary: fix CONFIG_IPUV3_CLK for imx51/imx53 boundary.h: fix build warnings when HAB enabled nitrogen6dl2g_defconfig: remove extra define of CONFIG_SYS_EXTRA_OPTIONS boundary: fix CONFIG_ETHPRIME(FEC0) for imx6sx boundary: add eth.c/padctrl.h nitrogen6x: use common code for eth init nitrogen6x: add CONFIG_SYS_BOARD_MULTIPLE to defconfigs boundary: eth: use mask to compare ksz9021 boundary: move eth.c to common directory nitrogen6x: eth.c now in common directory nitrogen6x: move misc_init_r/do_kbd to common nitrogen6x: remove CONFIG_SYS_BOARD_MULTIPLE use undef CONFIG_SYS_BOARD instead nitrogen6x: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common nitrogen6x: const i2c_pads_info nitrogen6x: use common 1066mhz_4x256mx16.cfg nitrogen6x: use common 1066mhz_4x128mx16.cfg nitrogen6x: use common 800mhz_4x128mx16.cfg nitrogen6x: add CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs nitrogen6x: 800mhz_2x128mx16.cfg: remove _P1 accesses nitrogen6x: 800mhz_2x256mx16.cfg: remove _P1 accesses nitrogen6x: 800mhz_2x128mx16.cfg: use common values CFG0: 0x40435323 to 0x3f435333 tRFC - 65 to 64 clocks tFAW - 19 to 20 clocks CFG1: 0xB66E8D63 to 0xb68e8b63 tRC from 20 to 21 clocks tWR from 7 to 6 clocks MR0: 0x13208030 to 0x15208030 tWR from 5 to 6 clocks nitrogen6x: 800mhz_2x256mx16.cfg: use common values MDCFG0: from 0x696c5323 to 0x666a5333 tRFC - from 106 to 103 clocks tXS - from 109 to 107 clocks tFAW - from 19 to 20 clocks MDCFG1: from 0xb66e8d63 to 0xb68e8b63 tRC - from 20 to 21 clocks tWR - from 7 clocks to 6 clocks MDRWD: from 0x000026d2 to 0x0f9f26d2 restore unused field to default value MDOR: from 0x006c1023 to 0x006a1023 tXPR - from 109 to 107 clocks MR0: from 0x13208030 to 0x15208030 tWR - from 5 to 6 clocks nitrogen6x: 800mhz_4x256mx16.cfg: use common values MDCFG0: from 0x696c5323 to 0x666a5333 tRFC - from 106 to 103 clocks tXS - from 109 to 107 clocks tFAW - from 19 to 20 clocks MDCFG1: from 0xb66e8d63 to 0xb68e8b63 tRC - from 20 to 21 clocks tWR - from 7 clocks to 6 clocks MDRWD: from 0x000026d2 to 0x0f9f26d2 restore unused field to default value MDOR: from 0x006c1023 to 0x006a1023 tXPR - from 109 to 107 clocks MR0: from 0x13208030 to 0x15208030 tWR - from 5 to 6 clocks nitrogen6x: use common ddr scripts nitrogen6x: port to v2018.07 nitrogen6x: add VD_DT035BTFT panel Signed-off-by:
Laci Tele <laci@boundarydevices.com> 6x_bootscript-yocto-3.14.txt: Yocto boots from zImage 6x_bootscript-*-3.14.txt: Changed address range logic for SX when dtbname set 6x_bootscript-yocto-3.14: Add check for ${board} being undefined 6x_bootscript-ubuntu-3.14: Add check for ${board} being undefined 6x_bootscript-*-3.14.txt: Add dtb support for 6QP Signed-off-by:
Ian Coolidge <ian@boundarydevices.com> 6x_bootscript-mainline: switch to zImage booting nitrogen6x: add basic fastboot support 6x_bootscript-yocto-3.10.53: add Quad Plus dtb option nitrogen6x: declare TC358743 interrupt as input nitrogen6x.h: fixup update to v2017.01 boundary.h: increase fastboot buffer size boundary.h: add secure boot options boundary.h: fix USB host initialization 6x_bootscript-*-3.14.txt: add support for m4 specific dtb 6x_bootscript-mainline: update for new display configuration 6x_bootscript-mainline: switch to new panel naming 6x_bootscript-mainline: add support for BD070LIC2 6x_upgrade: re-introduce fs-specific load commands nitrogen6x: update to v2017.01 nitrogen6x: update to v2017.03 6x_bootscript-mainline: change default bootdir to be / boundary.h: add CONFIG_CMD_PART 6x_bootscript-mainline: fixup LVDS2 display handling 6x_bootscript-mainline: use UUID to identify root partition 6x_bootscript-mainline: introduce rfspart variable fixup boundary.h for 2017.07 boundary.h: use standard config_distro_bootcmd fixup 2 boundary.h for 2017.07 6x_bootscript-*-3.14.txt: add Silex mac address override support 6x_bootscript-yocto: remove obsolete commands 6x_bootscript-yocto: remove obsolete versions of script Signed-off-by:
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
sata_probe returns 1 for failure, so don't checkout for < 0 fixes: f19f1ecb dm: sata: Support driver model with the 'sata' command Signed-off-by:
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by:
-
- Jul 27, 2018
-
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
06/2010 errata saw a "Added HSC bypass clarification ENGcm08316" Signed-off-by: -
Troy Kisky authored
This was used to verify that the following ddr initialization code movement patches "use common ddr scripts" did not change the output result. Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Gary Bisson authored
Generates upgrade scripts and copies to a mount path as well as renaming the u-boot binary properly. Signed-off-by: -
Troy Kisky authored
boundary: cmd_kbd bd_common initial addition boundary: add max77823_init common routine boundary: common: more addition boundary: move board_type out of BSS section boundary: pass const i2c_pads_info to common_board_init boundary: add .scr to our script names to run, ie. upgrade.scr boundary: common: padctrl-mx6: add INPUT_FLOAT boundary: common: max77823: add max77823_otg_power boundary: add CONFIG_VIDEO_MXS for imx6sx/imx7d boundary: common: max77823: add max77823_boost_power boundary: common: add MAX77823 for TARGET_CID_TAB boundary: common: add fan53526 0.6-1.4V regulator boundary: common add 1066mhz_4x256mx16.cfg This is replacing nitrogen6x/1066mhz_4x256mx16.cfg boundary: common: max77823: allow wcin source boundary: common: ddr-setup: use WALAT value provided boundary: common: add 1066mhz_4x128mx16.cfg boundary: common: add 800mhz_4x128mx16.cfg boundary: common: add CONFIG_DEFAULT_HITACHI_HVGA boundary: common: add tamper support boundary: common: add uboot_release environment variable boundary: common: padctrl-mx51: add PAD_CTRL_INPUT boundary: common: bd_common: fix warning by declaring snvs_regs boundary: boundary.h: check for CONFIG_ENV_OFFSET already defined boundary: boundary.h: allow override of BD_CONSOLE_STR boundary: common: 800mhz_4x128mx16.cfg: use common values This is in preparation to delete this file. CFG0: 0x40435323 to 0x3f435333 tRFC - 65 to 64 clocks tFAW - 19 to 20 clocks CFG1: 0xB66E8D63 to 0xb68e8b63 tRC from 20 to 21 clocks tWR from 7 to 6 clocks MR0: 0x13208030 to 0x15208030 tWR from 5 to 6 clocks boundary: common: add ddr configuration files boundary: common: remove no longer used files boundary: common: add CONFIG_OTG_CHARGER, used by cid board boundary: common: max77823: determine USB cable type Use cable type to limit chrgin current so that the kernel will not print "vbus is not valid" when battery is mostly charged. U-boot consumption is low enough to not need the current limited, but booting kernel needs it limited. boundary: common: add max77823_is_charging max77823: initialize MAX77823_CHG_CNFG_01 for restart threshold boundary: common: max77823: add max77834_power_check boundary: common: add cmd_otg_cable Signed-off-by:
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Gary Bisson authored
The script currently doesn't use the standard distro variables. Signed-off-by:
-
