This converts the following to Kconfig:
   CONFIG_EMIF4
   CONFIG_SDRC

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>

This converts the following to Kconfig:
   CONFIG_MAC_ADDR_IN_SPIFLASH
   CONFIG_MAC_ADDR_IN_EEPROM

Signed-off-by: Adam Ford <aford173@gmail.com>

There was a check for CONFIG_MAC_ADDR_IN_EEPROM and
a check for CONFIG_MAC_ADDR_IN_SPIFLASH, however
some of the EEPROM related code wasn't encapsulated
inside the #if defined statement so the EEPROM code
could get executed even when it wasn't explicitly
enabled or wanted.

Signed-off-by: Adam Ford <aford173@gmail.com>

In mancy cases both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR point
to an otherwise-unused SMNAND_ENV_OFFSET.
This patch will set both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR to
whatever value was defined by SMNAND_ENV_OFFSET.

Signed-off-by: Adam Ford <aford173@gmail.com>

The DTS files had some spacing issues and they needed fixing. This
pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5.

To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.

Signed-off-by: Adam Ford <aford173@gmail.com>

V3: The resync broke card detect on MMC1 on Logic PD's Torpedo,
    so we add the cd-invert to the Torpedo's -u-boot.dtsi file.

V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo
    Remove the need for the second patch in the series

Either the USB and Fastboot were never finished, or somehow it got
lost.  This puts enough hooks back into omap3logic to enable
fastboot and hopefully prepare it for Kconfig conversion.

Signed-off-by: Adam Ford <aford173@gmail.com>

Fix the building warning as below:
---8<----
Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50
Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50
--->8----

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Some device the serial console's initialization cannot run early during
the boot process. Hence, nulldev serial device is helpful on that
situation.

For example, if the serial module was implemented in FPGA. Serial
initialization is prohibited to run until the FPGA was programmed.

This commit is to adding nulldev serial driver. This will allows the
default console to be specified as a nulldev.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>

With debug enabled, SPL output following these debug prints is on the
same line and it is hard to read. Fix it.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Like the OMAP-L138 LCDK before it, let's move the da850-evm and
the variations to TI_COMMON_CMD_OPTIONS to cut back one some of the
defconfig entries.

Signed-off-by: Adam Ford <aford173@gmail.com>

Some drivers in Linux (ex. drivers/mtd/nand/denali.c) use
ioread*/iowrite* accessors.  Import them to make drivers more
synced.  I copied code from include/asm-generic/io.h of Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig. Updated with savedefconfig.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>

Much of the AM3517 functions are copies of the standard definitions
used in ti_omap3_common.h.  Moving to include a common file
reduces the amount of duplicative code and clutter.  A few
AM3517 specific functions (like EMIF4) are explictly defined
and a few items are undefined or redefined, but overall the number
of lines of code shink.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>

Add space around operator "+", make it
match the coding style.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>

Add the new compatible "atmel,24mac402" to accommodate AT24MAC402.
The AT24MAC402 is a 2K Serial EEPROM and the 2-Kbit memory array
is internally organized as 16 pages of 16 bytes of EEPROM each.
The 48-bit EUI address in the AT24MAC402 are located in the extended
memory block.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

Add the new compatible "microchip,24aa02e48" to accommodate 24AA02E48,
the 24AA02E48 is a 2K I2C Serial EEPROM with pre-programmed globally
unique, 48-bit node address, and 8-byte page size.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

The PMMC firmware should be bundled with the FIT image for HS devices,
remove the steps that load and install this firmware outside of FIT.

Signed-off-by: Andrew F. Davis <afd@ti.com>

The PMMC firmware should be bundled into a FIT image on HS
devices to allow authentication/decryption, add a handler to
process this PMMC firmware.

Signed-off-by: Andrew F. Davis <afd@ti.com>

Add a new image type representing TI Power Management
Micro-Controller (PMMC) Firmware image type.

Signed-off-by: Andrew F. Davis <afd@ti.com>

Solves build issue:

  Building current source for 134 boards (12 threads, 1 job per thread)
         arm:  +   lsxhl
  +examples/api/vsprintf.o: In function `string16':
  +lib/vsprintf.c:278: undefined reference to `memcpy'
  +examples/api/uuid.o: In function `uuid_bin_to_str':
  +lib/uuid.c:197: undefined reference to `memcpy'
  +lib/uuid.c:199: undefined reference to `memcpy'
  +make[3]: *** [examples/api/demo] Error 1
  +make[2]: *** [examples/api] Error 2
  +make[1]: *** [examples] Error 2
  +make: *** [sub-make] Error 2
    133    0    1 /134    sheevaplug

Signed-off-by: Rob Clark <robdclark@gmail.com>

This works (roughly) the same way as linux's, but we currently always
print lower-case (ie. we just keep %pUB and %pUL for compat with linux),
mostly just because that is what uuid_bin_to_str() supports.

  %pUb:   01020304-0506-0708-090a-0b0c0d0e0f10
  %pUl:   04030201-0605-0807-090a-0b0c0d0e0f10

It will be used by a later efi_loader paths for efi variables and for
device-path-to-text protocol, and also quite useful for debug prints
of protocol GUIDs.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

This is convenient for efi_loader which deals a lot with UTF-16.  Only
enabled with CC_SHORT_WCHAR, leaving room to add a UTF-32 version when
CC_SHORT_WCHAR is not enabled.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

We'll eventually want these in a few places in efi_loader, and also
vsprintf.

Signed-off-by: Rob Clark <robdclark@gmail.com>

EFI_LOADER really wants UTF-16 strings (ie. %ls and L"string" are 16bit
chars instead of 32bit chars).  But rather than enabling -fshort-wchar
conditionally if EFI_LOADER is enabled, it was deemed preferrable to
globally switch.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>

We now can no longer re-use the provided path and need to give the
full PATH we want used now.

Signed-off-by: Tom Rini <trini@konsulko.com>

This allows to scan the DT including all "clocks" node's sub-nodes
in which fixed-clock are defined.
All fixed-clock should be defined inside a clocks node which collect all
external oscillators. Until now, all clocks sub-nodes can't be binded except
if the "simple-bus" compatible string is added which is a hack.

Update test.dts by moving clk_fixed node inside clocks.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

Currently, all fixed-clock declared in "clocks" node in device tree
can be binded by clk_fixed_rate.c driver only if each of them have
the "simple-bus" compatible string.
This constraint has been invoked here [1].

This patch offers a solution to avoid adding "simple-bus" compatible
string to nodes that are not busses.

[1] https://patchwork.ozlabs.org/patch/558837/



Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add support for reading a list of bouncing addresses from a in-tree file
(doc/bounces) and from the ~/.patman config file. These addresses are
stripped from the Cc list.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich &lt;philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com&gt;>

Adjust this code so that it can work with Python 2 and 3.

Fixes: d73fcb12 (moveconfig: Support building a simple config database)
Reported-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>

Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.

Signed-off-by: Simon Glass <sjg@chromium.org>

At present we sometimes see warnings of the form:

/tmp/tmpMA89kB:36: warning: overriding the value of CMD_SPL.
	Old value: "y", new value: "y".

This is not very useful as it does not show whch defconfig file it relates
to. Update the tool to show this.

Signed-off-by: Simon Glass <sjg@chromium.org>

It is often useful to see which driver was actually selected for each
device. Add a new 'Driver' column to provide this information. Sample
output:

 Class       Probed   Driver     Name
----------------------------------------
 root        [ + ]    root_drive root_driver
 keyboard    [ + ]    i8042_kbd  |-- keyboard
 serial      [ + ]    ns16550_se |-- serial
 rtc         [   ]    rtc_mc1468 |-- rtc
 timer       [ + ]    tsc_timer  |-- tsc-timer
 syscon      [ + ]    ich6_pinct |-- pch_pinctrl
 pci         [ + ]    pci_x86    |-- pci
 northbridge [ + ]    bd82x6x_no |   |-- northbridge@0,0
 video       [ + ]    bd82x6x_vi |   |-- gma@2,0
 vidconsole0 [ + ]    vidconsole |   |   `-- gma@2,0.vidconsole0
...

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>

We can use printf() to limit the string width. Adjust the code to do this
instead of using strlcpy() which is a bit clumbsy.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>

Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct
number depending on which host we are going to build and run.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>