- Sep 30, 2017
-
-
Heinrich Schuchardt authored
CONFIG_ENV_OFFSET is already defined in include/configs/rockchip-common.h For CONFIG_ROCKCHIP_BACK_TO_BROM=y we redefine CONFIG_ENV_OFFSET to an unsuitable value. We were lucky to get a compiler warning. Remove the incorrect redefinition. Signed-off-by:
Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by:
Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by:
-
Kever Yang authored
The boot mode for rk322x is stored in sysreg 0, update it. Signed-off-by:
Kever Yang <kever.yang@rock-chips.com> Acked-by:
-
Elaine Zhang authored
add i2c1 and rk805 nodes to support rk805 init setting. Signed-off-by:
Elaine Zhang <zhangqing@rock-chips.com> Signed-off-by:
-
Elaine Zhang authored
Add defconfig for rk8xx and regulator and i2c controller. Signed-off-by:
-
Elaine Zhang authored
Add compatible to support rk3328 i2c Signed-off-by:
Heiko <Schocher<hs@denx.de>
-
Philipp Tomsich authored
Apparently, our earlier assumption that the BROM will always set up the iomux for SDcard communication does not always hold true: when booting U-Boot from the on-module (on the RK3368-uQ7) eMMC, the SDcard pins are not set up and need to be configured by the pinctrl driver to allow SD card access. This change implements support for setting up the SDMMC pins in pinctrl for the RK3368. Reported-by:
Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by:
Simon Glass <sjg@chromium.org>
-
Philipp Tomsich authored
The RK3368-uQ7 ATF has been moved back to 0x100000 (1MB from the start of DRAM) to avoid it overwriting the active SPL stage during FIT image loading. This change adapts the .its to match up (again) with our ATF repository for the RK3368-uQ7. Signed-off-by:
-
Jagan Teki authored
Add Falcon mode support in vyasa rk3288 board. Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Reviewed-by:
-
Jagan Teki authored
Since the size of SPL can't be exceeded 0x8000 bytes in RK3288, it is not possible add new SPL features like Falcon mode or etc. So add TPL stage so-that adding new features to SPL is possible. - TPL: DRAM init, clocks - SPL: MMC, falcon, etc Signed-off-by:
-
Jagan Teki authored
configure_l2ctlr will be shared between SPL and TPL so move them into asm/arch/sys_proto.h Signed-off-by:
-
Jagan Teki authored
L2CTLR read/write functions are common to armv7 so, move them in to include/asm/armv7.h and use them where ever it need. Cc: Tom Warren <twarren@nvidia.com> Signed-off-by:
-
Kever Yang authored
The pd_bus hclk/pclk source is pd_bus aclk, not the PLL. Signed-off-by:
-
Kever Yang authored
Add support for rk3128 package header in mkimage tool. Signed-off-by:
-
Kever Yang authored
Some of macros definition are not correct, fix them according to TRM. Signed-off-by:
-
Kever Yang authored
Fix typo RK322X/RK3036 in rk322x clock driver. Signed-off-by:
-
Philipp Tomsich authored
Instead of directly calling into the back-to-bootrom code, the RK3399 common SPL implementation now uses BOOT_DEVICE_BOOTROM to trigger a transfer back into the bootrom. With this factored out, the spl_board_init function can not be customised for each RK3399 board. Signed-off-by:
-
Philipp Tomsich authored
Remove a duplicate CONFIG_ENV_IS_IN_MMC assignment for the lion-rk3368 defconfig. Signed-off-by: -
Kever Yang authored
RK3188 using the same ddr_conf for both 15 bit and 16 bit row address. Signed-off-by:
-
Kever Yang authored
The dram channel info will be auto detect by the driver, we do not need it. Signed-off-by: -
Kever Yang authored
Add driver for rk322x to support sdram initialize in SPL. Signed-off-by:
-
Kever Yang authored
Since we have CONFIG_RAM framwork and its driver folder, move the driver into it. Signed-off-by:
-
Kever Yang authored
Since we have CONFIG_RAM framwork and its driver folder, move the driver into it. Signed-off-by:
-
Kever Yang authored
Since we have CONFIG_RAM framwork and its driver folder, move the driver into it. Signed-off-by:
-
Kever Yang authored
Since we have CONFIG_RAM framwork and its driver folder, move the driver into it. Signed-off-by:
-
Philipp Tomsich authored
Enable the Rockchip SARADC driver for all Rockchip SoCs. Note that the SARADC peripheral is available on all SoCs except the RK3036 and RK3228. However, as this is a DM-driver, enabling by default will not cause any function problems (and can always be changed from defconfig, if size is a concern). Signed-off-by:
David Wu <david.wu@rock-chips.com>
-
David Wu authored
Enable the SARADC for download key pressed detect. Signed-off-by:
-
David Wu authored
Enable the SARADC for download key pressed detect. Signed-off-by:
-
David Wu authored
Enable the SARADC for download key pressed detect. Signed-off-by:
-
David Wu authored
Enable the SARADC for download key pressed detect. Signed-off-by:
-
David Wu authored
Enable the SARADC for download key pressed detect. Signed-off-by:
-
David Wu authored
Enable the SARADC for download key pressed detect. Signed-off-by:
-
David Wu authored
Signed-off-by:
-
David Wu authored
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1). SARADC integer divider control register is 8-bits width. Signed-off-by:
-
David Wu authored
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1). SARADC integer divider control register is 8-bits width. Signed-off-by:
-
David Wu authored
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1). SARADC integer divider control register is 10-bits width. Signed-off-by:
-
David Wu authored
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1). SARADC integer divider control register is 8-bits width. Signed-off-by:
-
David Wu authored
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1). SARADC integer divider control register is 10-bits width. Signed-off-by:
-
David Wu authored
The ADC can support some channels signal-ended some bits Successive Approximation Register (SAR) A/D Converter, like 6-channel and 10-bit. It converts the analog input signal into some bits binary digital codes. Signed-off-by:
-
- Sep 29, 2017
-
-
Sam Protsenko authored
Add tracing printings to Linux/Android boot commands, so that we can see what's going on. Helps to trace possible bugs on early stages and improves the output for user (which is especially useful, because we have a bunch of boot commands executing one by one). Signed-off-by:
Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by:
Tom Rini <trini@konsulko.com>
-
Sam Protsenko authored
Extract commands for booting Linux from eMMC to separate command. It seems more logical that way, and allows us to run the whole command set from U-Boot shell with only one command. Signed-off-by:
-
