STM32F7 and STM32H7 shares the same UART block, add
STM32H7 compatible string.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

STM32H7 SoCs uses the same pinctrl block as found into
STM32F7 SoCs

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>

Since we may jump to next stage like ATF/OP-TEE instead of U-Boot,
we need to stash the bootstage info before it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add usb_gadget_handle_interrupts(), board_usb_init(),
board_usb_cleanup() and g_dnl_board_usb_cable_connected()
callbacks needed for FASTBOOT support

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Update ehci and ohci node's compatible string in order to
use ehci-generic and ohci-generic drivers.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

On STi 96boards, configure by default the micro USB connector
(managed by DWC3 hardware block) in peripheral mode.
This will allow to use fastboot feature.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.

Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Enable USB Host Networking support by enabling Ethernet/USB
adaptors support and by enabling some BOOTP flags

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This is the generic phy driver for the picoPHY ports
used by USB2/1.1 controllers. It is found on STiH407 SoC
family from STMicroelectronics.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

reset-names property is needed to use the reset
API for STi sdhci driver.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Use struct udevice* as input parameter. Previous
parameters are retrieved through plat and priv data.

This to prepare to use the reset framework.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

'default n' is the default anyway so it doesn't need to be specified
explicitly, and the rest of the file doesn't specify it either anywhere.
Drop it.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

This field is no longer used since the DM conversion. Drop it.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

This field is no longer used since the DM conversion. Drop it.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

This field has never been used as the driver has been DM-based since the
beginning. Drop it.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

These take the 'struct udevice *' as an argument, not the
'struct xilinx_pcie *` which is a local variable. Fix the comments to
match the code.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

We have limited stack in SPL builds.  Drop itrblock and move to
malloc/free of itr to move this off of the stack.  As part of this fix a
double-free issue in fat_size().

Signed-off-by: Tom Rini <trini@konsulko.com>
---
Rework to use malloc/free as moving this to a global overflows some SH
targets.

Support spi driver and can detect MX25U1635E flash on AE3XX board.

Verification:

sf probe 0:0 50000000 0
spi_flash_std_probe(sf_Probr.c)
	spi_flash_probe_slave(sf_Probr.c)
	SF: Detected mx25u1635e with page size 256 Bytes, erase size 4 KiB, total 2 MiB
	NDS32 # sf test 0x100000 0x1000
	SPI flash test:
	0 erase: 34 ticks, 117 KiB/s 0.936 Mbps
	1 check: 15 ticks, 266 KiB/s 2.128 Mbps
	2 write: 21 ticks, 190 KiB/s 1.520 Mbps
	3 read: 11 ticks, 363 KiB/s 2.904 Mbps
	Test passed
	0 erase: 34 ticks, 117 KiB/s 0.936 Mbps
	1 check: 15 ticks, 266 KiB/s 2.128 Mbps
	2 write: 21 ticks, 190 KiB/s 1.520 Mbps
	3 read: 11 ticks, 363 KiB/s 2.904 Mbps

Signed-off-by: rick <rick@andestech.com>

Add spi dts node and enable spi dm flash config.

Signed-off-by: rick <rick@andestech.com>

To support MACRONIX MX25U1635E 16M-BIT flash.

Signed-off-by: rick <rick@andestech.com>

After soft reset complete, write mac address immediately will fail.
Add delay to work around this problem.

Signed-off-by: rick <rick@andestech.com>

Enable cache and ftmac100 performance can be improved.

Signed-off-by: rick <rick@andestech.com>

Add cache inval and flush when rx and tx.

Signed-off-by: rick <rick@andestech.com>

move #include <asm/setup.h> from bootm.c to bootm.h

Signed-off-by: rick <rick@andestech.com>

Add #include <asm/mach-types.h> to fix it.

Signed-off-by: rick <rick@andestech.com>

Add Serial Download Protocol support (SDP), which allows loading
SPL and u-boot.img via imx_usb_loader tool as explained in
doc/README.sdp.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

Instead of having every board file to add its own g_dnl_bind_fixup()
implementation, move it to the common imx6 SPL code.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>

Define i2c mux configuration.  Add new vpd_reader which is used to read
vital product data.  Read VPD from EEPROM and set eth0 MAC address.

Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Jose Alarcon <jose.alarcon@ge.com>

The hummingboard2 is slightly different to the cubox i and to the
hummingboard. The GPIO pin info to probe came from solidruns
for of u-boot on github.
https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589


I have tested on a hummingboard-edge witha  imx6 solo and 512mb of
ram.

Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>

Increase serialno_str to 17 bytes so it can hold the 16 bytes long serial
nummer and the terminating null byte added by snprintf.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>

After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/



Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/



Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

The RK3368 TPL stage always returns to the BootROM, so it has no need
for the eMMC, SD and SPI nodes.  This marks those nodes (that should
be included in SPL, but not TPL) as 'u-boot,dm-spl'.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

With the new 32/64bit-aware dtoc, the type of reg is fdt64_t and the
OF_PLATDATA structure layout changes.  This adjusts the DMC driver for
the RK3368 to track these changes.

For the time being (i.e. until regmap_init_mem_platdata works for the
64bit case), we won't use regmap_init_mem_platdata here and simply
access of_plat.reg[] directly.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

With dtoc emitting fdt64_t for addresses (and region sizes), the array
indices for accessing the reg[] array needs to be adjusted.  This
adjusts the Rockchip DM timer driver to correctly handle OF_PLATDATA
given this new structure layout.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>