PPA loading during SPL stage is not required for nornal
SD boot scenario.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

PPA loading during SPL stage is not required for nornal
SD boot scenario.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.

For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html



Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add spi dts node and enable spi dm flash config.

Signed-off-by: rick <rick@andestech.com>

Add Serial Download Protocol support (SDP), which allows loading
SPL and u-boot.img via imx_usb_loader tool as explained in
doc/README.sdp.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

With the critical drivers ready for switching to a live tree, we can
now enable it in the defconfig for the RK3399-Q7.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add the missing target and pinctrl config for rk3368 sheep board

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

This patch adds support for Vyasa RK3288 initial board
from Amarula Solutions.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

This adds OF_LIVE and BOOTSTAGE support for the RK3368-uQ7 and
regenerates the defconfig (picking up a few changes/reorderings) from
upstream Kconfig changes.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

This patch adds USB configs to support the USB OTG port(consist
of DWC2 controller) and the USB Host port(consist of EHCI and OHCI
controllers) on evb-rv1108 board, and also support fastboot over
USB and USB mass storage.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version.  This is now distinguished by DT.  Merge the two defconfig
files into uniphier_v7_defconfig.

Update the README.uniphier too.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Enable this option for link so that the timer is available earlier.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

The CONFIG_BOOTSTAGE_USER_COUNT option is no-longer needed since we can now
support any number of user IDs. Also BOOTSTAGE_ID_COUNT is not needed now.

Drop these unused options.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

This adds support to Intel Cherry Hill board, a board based on
Intel Braswell SoC. The following devices are validated:

- serial port as the serial console
- on-board Realtek 8169 ethernet controller
- SATA AHCI controller
- EMMC/SDHC controller
- USB 3.0 xHCI controller
- PCIe x1 slot with a graphics card
- ICH SPI controller with an 8MB Macronix SPI flash
- Integrated graphics device as the video console

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add unit tests for sandbox default config.

Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>

Add unit tests for the 'gpt rename' and 'gpt swap' commands that
rely on the block device created by test/py/make_test_disk.py.
Add CONFIG_CMD_GPT_RENAME to the sandbox_defconfig.  Remove the
testdisk.raw test device at the end of the tests.

Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.

The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_EMIF4
   CONFIG_SDRC

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>

This converts the following to Kconfig:
   CONFIG_MAC_ADDR_IN_SPIFLASH
   CONFIG_MAC_ADDR_IN_EEPROM

Signed-off-by: Adam Ford <aford173@gmail.com>

Either the USB and Fastboot were never finished, or somehow it got
lost.  This puts enough hooks back into omap3logic to enable
fastboot and hopefully prepare it for Kconfig conversion.

Signed-off-by: Adam Ford <aford173@gmail.com>

Like the OMAP-L138 LCDK before it, let's move the da850-evm and
the variations to TI_COMMON_CMD_OPTIONS to cut back one some of the
defconfig entries.

Signed-off-by: Adam Ford <aford173@gmail.com>

Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig. Updated with savedefconfig.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>

Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Replace the code to set the ethernet mac address with the code from
the common folder.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Add support for selecting proper dtb for
dra76x u-boot from FIT.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Enabled PCIe support and PCI command feature.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

This patch add support of LS1088AQDS platform.

The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>

WIP: disable NAND for LS1088ARDB

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: dropped redundant commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

This board does dwc3 gadget, not host, so we cannot have host support or
we will fail to link.

Signed-off-by: Tom Rini <trini@konsulko.com>

This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Disable CONFIG_ARCH_FIXUP_FDT_MEMORY to prevent U-Boot from modifying
the memory {} nodes in the DT passed to the Linux kernel. The R8A779x
DT contains multiple memory {} nodes, while U-Boot only modifies the
first one and stuffs all the memory entries into it, which is wrong.
Disabling CONFIG_ARCH_FIXUP_FDT_MEMORY is the least intrusive way to
fix the issue this close to the release, while the real fix is to
extend the fdt_fixup_memory_banks() to handle multiple memory nodes
in DT.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This reverts commit 25877d4e.

This is a workaround for Raspberry Pi boot failures seen when passing on
the device tree provided by the Raspberry Pi firmware at boot. Without
CONFIG_OF_EMBED, we just get stuck at "Starting kernel ..." when we try
to boot Linux with this device tree.

Signed-off-by: Paul Barker <pbarker@toganlabs.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>

enable the ATF option and SDCard in defconfig.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Read SoM information from EEPROM and set ethaddr in late init.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>