All sata based drivers are bind and corresponding block
device is created. Based on this find_scsi_device() is able
to get back block device based on scsi_curr_dev pointer.

intr_scsi() is commented now but it can be replaced by calling
find_scsi_device() and scsi_scan().

scsi_dev_desc[] is commented out but common/scsi.c heavily depends on
it. That's why CONFIG_SYS_SCSI_MAX_DEVICE is hardcoded to 1 and symbol
is reassigned to a block description allocated by uclass.
There is only one block description by device now but it doesn't need to
be correct when more devices are present.

scsi_bind() ensures corresponding block device creation.
uclass post_probe (scsi_post_probe()) is doing low level init.

SCSI/SATA DM based drivers requires to have 64bit base address as
the first entry in platform data structure to setup mmio_base.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

By adding labels to the cpu nodes in the dtsi, a dts that
includes it can change the OPPs by referencing the cpu0
through the label.

[Based on linux (400b6a0cbef55d1ae32808eaa1ef1c28820bf6ac)]
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.

Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

The most of ethernet drivers are using this mdio registration sequence.
strcpy(priv->bus->name, "emac");
mdio_register(priv->bus);
Where driver can be used only with one MDIO bus because only unique
name should be used.

Other drivers are using unique device name for MDIO registration to
support multiple instances.
snprintf(priv->bus->name, sizeof(bus->name), "%s", name);

With DM dev->seq is used more even in logs
(like random MAC address generation:
printf("\nWarning: %s (eth%d) using random MAC address - %pM\n",
       dev->name, dev->seq, pdata->enetaddr);
)
where eth%d prefix is used.

Simplify driver code to register mdio device with dev->seq number
to simplify mdio registration and reduce code duplication across
all drivers. With DM_SEQ_ALIAS enabled dev->seq reflects alias setting.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Tom Rini <trini@konsulko.com>

The EVP_MD_CTX and EVP_CIPHER_CTX are made opaque since 1.1.x , so instead
of embedding them directly into struct sb_image_ctx and initializing them
using EVP_*_CTX_init(), we use pointers and allocate the crypto contexts
using EVP_*_CTX_new().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>

Shuffle the macros around a little to remove the following warning
when building for i.MX28:

arch/arm/cpu/arm926ejs/mxs/spl_boot.c:44:26: warning: ‘iomux_boot’ defined but not used [-Wunused-const-variable=]
 static const iomux_cfg_t iomux_boot[] = {
                          ^~~~~~~~~~

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>

Add compatibility string for the Ingenic JZ4780 SoC, the necessary
UART enable bit into FCR and register shift. Neither are encoded
in the DTS coming from Linux, so we need to support it this way.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Add driver data to each compatible string to identify the type of
the port. Since all the ports in the driver are entirely compatible
with 16550 for now, all are marked with PORT_NS16550. But, there
are ports which have specific quirks, like the JZ4780 UART, which
do not have any DT property to denote the quirks. Instead, Linux
uses the compatible string to discern such ports and enable the
necessary quirks.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>

Add function which allows fetching the default FCR register setting
from platform data for DM , while retaining old behavior for non-DM
by returning UART_FCRVAL.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

Migrate CONFIG_ARCH_USE_MEMSET/MEMCPY with this merge.

Signed-off-by: Tom Rini <trini@konsulko.com>

Add FEC support for Engicam i.CoreM6 RQS modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add FEC node for Engicam i.CoreM6 RQS modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add FEC support for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add FEC node for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam i.CoreM6 RQS modules.

icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl-rqs> i2c dev 0
Setting bus to 0
icorem6qdl-rqs> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl-rqs> i2c probe
Valid chip addresses: 4F
icorem6qdl-rqs> i2c md 4F 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000  (active 0)
   4f: generic_4f, offset len 1, flags 0
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C nodes for Engicam i.CoreM6 RQS modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Rename defconfig files for better compatible with
respective board names and dts files.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07)
Trying to boot from MMC1

U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:56:07 +0530)

CPU:   Freescale i.MX6DL rev1.3 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 DualLite/Solo RQS Starter Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl-rqs>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44)
Trying to boot from MMC1

U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530)

CPU:   Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl-rqs>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

geam6ul> mtdparts

device nand0 <nand>, # parts = 6
0: spl                 0x00200000      0x00000000      0
1: uboot               0x00200000      0x00200000      0
2: env                 0x00100000      0x00400000      0
3: kernel              0x00400000      0x00500000      0
4: dtb                 0x00100000      0x00900000      0
5: rootfs              0x1f600000      0x00a00000      0

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Enable MTD device, partition and command support.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add NAND support for Engicam GEAM6UL board.

Boot Log:
--------
U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28)
Trying to boot from NAND
NAND : 256 MiB

U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100)

CPU:   Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz)
CPU:   Automotive temperature grade (-40C to 125C) at 42C
Reset cause: WDOG
Model: Engicam GEAM6UL
DRAM:  128 MiB
NAND:  256 MiB
MMC:   FSL_SDHC: 0
* Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam GEAM6UL module.

geam6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
geam6ul> i2c dev 0
Setting bus to 0
geam6ul> i2c dev
Current bus is 0
geam6ul> i2c speed 100000
Setting bus speed to 100000 Hz
geam6ul> i2c probe
Valid chip addresses: 2C
geam6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C nodes for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Boot Log:
--------
U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30)
Trying to boot from MMC1

U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR
Model: Engicam GEAM6UL
DRAM:  128 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
geam6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add i.MX6UL dtsi support from Linux.

Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam i.CoreM6 qdl board.

icorem6qdl> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl> i2c dev 2
Setting bus to 2
icorem6qdl> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl> i2c probe
Valid chip addresses: 2C
icorem6qdl> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>

Some I2C bus devicetree nodes, doesn't require to have
gpio pinctrl so replace the dev_info to debug so the
print never comes on the console and for bus that uses
gpio pinctrl anyway have dev_err.

Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.

After:
------
U-Boot> i2c dev 1
Setting bus to 1

Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>

Better to print the hex value for bus address instead of
decimal, for more readbility on bus addressing.

Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 35274752, no gpio pinctrl state.

After:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.

Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>

Added kconfig for SYS_I2C_MXC driver.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add custom splashscreen, engicam.bmp support for
Engicam i.CoreM6 qdl board.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Added kconfig entry for CONFIG_VIDEO_IPV3 driver.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Use CONFIG_DM_ETH and remove board_eth_init code
from board files.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add FEC dts support for Engicam i.CoreM6 dql modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add .read_rom_hwaddr on dm eth_ops.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

- Remove exctra space
- Add space
- Add tab space
- Fix single line comments quotes
- Fix 'CHECK: Avoid CamelCase'
- Fix 'CHECK: Alignment should match open parenthesis'
- Fix 'WARNING: line over 80 characters'
- Re-arrage header include files

Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>