Add I2C support for Engicam Is.IoT MX6UL module.

isiotmx6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
isiotmx6ul> i2c dev 0
Setting bus to 0
isiotmx6ul> i2c dev
Current bus is 0
isiotmx6ul> i2c speed 100000
Setting bus speed to 100000 Hz
isiotmx6ul> i2c probe
Valid chip addresses: 00 2C 44 78
isiotmx6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1

U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
isiotmx6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

This moves all of the current ARM errata from various header files and in to
Kconfig.  This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config.  We now just select these once at the higher level in Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

This patch provides u-boot support for Liebherr (LWN) mccmon6 board.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>

Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.

[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html



Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>

This option should not really be user selectable.  Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)

Add FEC support for Engicam i.CoreM6 RQS modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add FEC support for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam i.CoreM6 RQS modules.

icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl-rqs> i2c dev 0
Setting bus to 0
icorem6qdl-rqs> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl-rqs> i2c probe
Valid chip addresses: 4F
icorem6qdl-rqs> i2c md 4F 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000  (active 0)
   4f: generic_4f, offset len 1, flags 0
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44)
Trying to boot from MMC1

U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530)

CPU:   Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl-rqs>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam GEAM6UL module.

geam6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
geam6ul> i2c dev 0
Setting bus to 0
geam6ul> i2c dev
Current bus is 0
geam6ul> i2c speed 100000
Setting bus speed to 100000 Hz
geam6ul> i2c probe
Valid chip addresses: 2C
geam6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Boot Log:
--------
U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30)
Trying to boot from MMC1

U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR
Model: Engicam GEAM6UL
DRAM:  128 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
geam6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam i.CoreM6 qdl board.

icorem6qdl> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl> i2c dev 2
Setting bus to 2
icorem6qdl> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl> i2c probe
Valid chip addresses: 2C
icorem6qdl> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>

Use CONFIG_DM_ETH and remove board_eth_init code
from board files.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.

Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)

CPU:   Freescale i.MX6SLL rev1.0 at 792MHz
CPU:   Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM:  2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

add Kconfig entry for i.MX6SLL

Signed-off-by: Peng Fan <peng.fan@nxp.com>

liteBoard is a development board which uses liteSOM as its base.

Hardware specification:
 * liteSOM (i.MX6UL, DRAM, eMMC)
 * Ethernet PHY (id 0)
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>

Add thermal support on the Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

It's not necessary to define the processor in the defconfig file.

The preferred method to select the SoC is via Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>

This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>

This patch adds initial support for Samtec VIN|ING 2000 board.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>

UDOO Neo Board is a development board from Seco that has three models:
 - UDOO Neo Basic
 - UDOO Neo Basic Kick Starter
 - UDOO Neo Extended
 - UDOO Neo Full

All versions are based on the i.MX6 SoloX processor.

For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/

This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
https://github.com/fmntf/u-boot/commit/877b71184a5105e708024f232d36aed574961844



Only tested on the UDOO Neo Full board.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.

Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.

Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.

Signed-off-by: Eric Nelson <eric@nelint.com>

Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU           NXP i.MX6 DL, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q



Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6SOLO rev1.3 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM:  256 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
   Booting using the fdt blob at 0x18000000
   Using Device Tree in place at 18000000, end 1800a787

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0

Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6Q rev1.2 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.

Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)

CPU:   Freescale i.MX6ULL rev1.0 at 396MHz
CPU:   Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add support for Advantech DMS-BA16 board. The board is based on Advantech
BA16 module which has a i.MX6D processor. The board supports:
 - FEC Ethernet
 - USB Ports
 - SDHC and MMC boot
 - SPI NOR
 - LVDS and HDMI display

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6D
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: u-boot@lists.denx.de
Cc: sbabic@denx.de

Add Phytec-i.MX6 SOM with NAND

  Support:
   - 1GB RAM
   - Ethernet
   - SPI-NOR Flash
   - NAND (1024 MB)
   - external SD
   - UART

Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Custom Board based on MX6 Dual, 1GB RAM and eMMC.

There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).

Signed-off-by: Stefano Babic <sbabic@denx.de>

Add support for Technexion's PICO-IMX6UL-EMMC board.

For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc



Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX6SX" to boards using i.MX6 SoloX.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

This patch add support for the CCV xPress board which is equipped
with the i.MX6UL. And provides the following interfaces:

- 128MiB DDR
- UART
- I2C
- eMMC (with booting)
- Ethernet
- USB

This patch adds two build targets. One with and one without SPL. The
non-SPL version is used for loading U-Boot via USB (imx_usb_loader).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
 - FEC Ethernet
 - USB Ports
 - SDHC and MMC boot
 - SPI NOR
 - LVDS and HDMI display

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6D
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.

Signed-off-by: Ye Li <ye.li@nxp.com>

Congatec has several MX6 boards based on quad, dual, dual-lite and solo.

Add SPL support so that all the variants can be supported

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

Add CONFIG_ROM_UNIFIED_SECTIONS for mx6sx and mx6ul target
platforms to resolve corresponding HAB_RVT_BASE base address,
the RVT table contains pointers to the HAB API functions in
ROM code.

Signed-off-by: Adrian Alonso <aalonso@freescale.com>