There is no need for each OS specific function to call do_reset() we
can just do it once in bootm. This means its feasible on an error for
the OS boot function to return.

Also, remove passing in cmd_tbl_t as its not needed by the OS boot
functions.  flag isn't currently used but might be in the future so
we left it alone.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Move determing if we have a ramdisk and where its located into the
common code. Keep track of the ramdisk start and end in the
bootm_headers_t image struct.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Move entry point code out of each arch and into common code.
Keep the entry point in the bootm_headers_t images struct.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The autostart revert caused a bit of duplicated code as well as
code that was using images->autostart that needs to get removed so
we can build again.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Add 'ethaddr' and 'eth1addr' to the Linux kernel environment if
they are set in the U-Boot environment.

Signed-off-by: Jason McMullan <mcmullan@netapp.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

MIPS port has two problems in timer routines. One is now we assume CFG_HZ
equals to CP0 counter frequency, but this is wrong. CFG_HZ has to be 1000
in the U-Boot system.

The other is we don't have a proper time management counter like timestamp
other ARCHs have. We need the 32-bit millisecond clock counter.

This patch introduces timestamp and CYCLES_PER_JIFFY. timestamp is a
32-bit non-overflowing CFG_HZ counter, and CYCLES_PER_JIFFY is the number
of calculated CP0 counter cycles in a CFG_HZ.

STRATEGY:

* Fix improper CFG_HZ value to have 1000

* Use CFG_MIPS_TIMER_FREQ for timer counter frequency, instead.

* timer_init: initialize timestamp and set up the first timer expiration.
  Note that we don't need to initialize CP0 count/compare registers here
  as they have been already zeroed out on the system reset. Leave them as
  they are.

* get_timer: calculate how many timestamps have been passed, then return
  base-relative timestamp. Make sure we can easily count missed timestamps
  regardless of CP0 count/compare value.

* get_ticks: return the current timestamp, that is get_timer(0).

Most parts are from good old Linux v2.6.16 kernel.

v2:
- Remove FIXME comments as they turned out to be trivial.
- Use CP0 compare register as a global variable for expirelo.
- Kill a global variable 'cycles_per_jiffy'. Use #define CYCLES_PER_JIFFY
  instead.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

What we have to do is just to wait for given micro-seconds. No need to
take into account current time, get_timer and CFG_HZ.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

We already have many pre-defined CP0 access macros in <asm/mipsregs.h>.
This patch replaces mips_{compare,count}_set and mips_count_get with
existing macros.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

The mips architecture currently does not call 'spi_init()' in the generic
board initialization routine is CONFIG_CMD_SPI is defined.

This patch rectifies that problem.

Signed-off-by: Jason McMullan <mcmullan@netapp.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

This patch adds the standard 'nand_init()' call to the mips generic
'board_init_r()' call, bringing MIPS in line with the other architectures.

Signed-off-by: Jason McMullan <mcmullan@netapp.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Before new uImage code was merged, bootm code allowed for the kernel image to
get overwritten during decompresion. new uImage introduced a check for image
overwrites and refused to boot the image that got overwritten. This patch
restores the old behavior. It also adds a warning when the image overwriten is
a multi-image file, because in such case accessing componentes other than the
first one will fail.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

This patch updates architecture specific implementations of
do_bootm_linux() adding new uImage format handling for
operations like get kernel entry point address, get kernel
image data start address.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

boot_get_ramdisk() and image_get_ramdisk() do not need all
cmdtp, flag, argc and argv arguments. Simplify routines definition.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

This patch introduces the following prefix convention for the
image format handling and bootm related code:

genimg_		- dual format shared code
image_		- legacy uImage format specific code
fit_		- new uImage format specific code
boot_		- booting process related code

Related routines are renamed and a few pieces of code are moved around and
re-grouped.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Marian Balakowicz <m8@semihalf.com>

Do not pass image verification flag directly to related routines.
Simplify argument passing and move it to the bootm_header structure which
contains curently processed image specific data and is already being passed
on the argument list.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

This patch adds framework for dual format images. Format detection is added
and the bootm controll flow is updated to include cases for new FIT format
uImages.

When the legacy (image_header based) format is detected appropriate
legacy specific handling is invoked. For the new (FIT based) format uImages
dual boot framework has a minial support, that will only print out a
corresponding debug messages. Implementation of the FIT specific handling will
be added in following patches.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

- Fix flash_init call when CFG_NO_FLASH is used
- Remove no more needed flash.c for qemu-mips

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Architecture specific do_bootm_linux() routines share common
ramdisk image processing code. Move this code to a common
helper routine.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

Implementation of the do_bootm_linux() and other bootm helper routines is
architecture specific code. As such it resides in lib_<arch> directories
in files named <arch>_linux.c

This patch renames those files to a more clear and accurate
lib_<arch>/bootm.c form.

List of the renamed files:
   lib_arm/armlinux.c -> lib_arm/bootm.c
   lib_avr32/avr32_linux.c -> lib_avr32/bootm.c
   lib_blackfin/bf533_linux.c -> lib_blackfin/bootm.c
   lib_i386/i386_linux.c -> lib_i386/bootm.c
   lib_m68k/m68k_linux.c -> lib_m68k/bootm.c
   lib_microblaze/microblaze_linux.c -> lib_microblaze/bootm.c
   lib_mips/mips_linux.c -> lib_mips/bootm.c
   lib_nios/nios_linux.c -> lib_nios/bootm.c
   lib_nios2/nios_linux.c -> lib_nios2/bootm.c
   lib_ppc/ppc_linux.c -> lib_ppc/bootm.c
   lib_sh/sh_linux.c -> lib_sh/bootm.c

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

- use single image header pointer instead of a set of auxilliary variables.
- add multi component image helper routines: get component size/data address

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

- Add inline helper macros for basic header processing
- Move common non inline code common/image.c
- Replace direct header access with the API routines
- Rename IH_CPU_* to IH_ARCH_*

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

This patch has been sent on:
- 29 Sep 2007

Although mips_io_port_base is currently a part of IDE command, it is quite
fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move
it to MIPS general part, and introduce `set_io_port_base()' from Linux.

This patch is triggered by multiple definition of `mips_io_port_base' build
error on gth2 (and tb0229 also needs this fix.)

board/gth2/libgth2.a(gth2.o): In function `log_serial_char':
/home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base'
common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here
make: *** [u-boot] Error 1

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Heiko Schocher <hs@denx.de>

Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Jon Loeliger <jdl@freescale.com>

This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.

All transformations are of the form:
Before:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Based on patch by Mike Frysinger, 20 Jun 2006

Modifications are based on the linux kernel approach and
support two use cases:

  1) Add O= to the make command line
  'make O=/tmp/build all'

  2) Set environement variable BUILD_DIR to point to the desired location
  'export BUILD_DIR=/tmp/build'
  'make'

The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'

Command line 'O=' setting overrides BUILD_DIR environent variable.

When none of the above methods is used the local build is performed and
the object files are placed in the source directory.

  - fix problems with examples/stubs.c for GCC >= 3.4
  - fix problems with gd initialization

* Enable FAT filesystem support for HMI10 board

Sort Makefile.
Update docs.

  Fix Intel 28F128J3 ID in include/flash.h

* Patch by Masami Komiya, 09 Jan 2004:
  add support for TB0229 board (NEC VR4131 MIPS processor)

* Patch by Leon Kukovec, 12 Dec 2003:
  changed extern __inline__ into static __inline__ in
  include/linux/byteorder/swab.h