Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

* 'master' of git://git.denx.de/u-boot-mmc:
  Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec"
  mmc: mv_sdhci: Fix host version read for Armada100

As a result of the commit 68332608 the uart16550 driver
is broken for Microblaze big endian systems, because of
the missing 3 byte offset. Other than as described, not
all U-Boot BSP will treat properly the 3 byte offset.

This why prefer to mask out the 3 byte offset in general
and setup correct _REG_SIZE value depending on edianess.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Tested-by: Michal Simek <monstr@monstr.eu>

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>

cmd_nvedit.c: In function 'do_env_grep':
cmd_nvedit.c:182:3: warning: suggest parentheses around assignment used as truth value

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

Fix:

x86emu/ops2.c: In function 'x86emuOp2_set_byte':
x86emu/ops2.c:171:11: warning: variable 'name' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This reverts commit 02f3029f.

This patch add 3 times retry to CMD8 because the Marvell mmc controller
doesn't obey the power ramp up process in the SD specification 6.4.1.
(Please refer to figure 6.1 and 6.2 in the specification.)

The CMD0 should be send after power ramp up has been finished.
However, the Marvell mmc contorller must do power ramp up after the
first CMD0 command has been send.

This patch also affect existing platforms like Nokia N900 and other
platforms.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>

sdhci_readw does not work for host version read in Armada100 series
SoCs. This patch fix this issue by making a sdhci_readl call to get host
version.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

* 'hs@denx.de' of git://git.denx.de/u-boot-staging:
  drivers/net/dnet.c: Fix GCC 4.6 warnings
  board/xaeniax/flash.c: Fix GCC 4.6 warnings
  net/bootp.c: Fix GCC 4.6 warning
  common/cmd_bootm.c: Fix GCC 4.6 warnings
  board/mx1ads/mx1ads.c: Fix GCC 4.6 warning
  board/mx1ads/syncflash.c: Fix GCC 4.6 warnings
  board/lubbock/flash.c: Fix GCC 4.6 warnings
  drivers/net/cs8900.c: Fix GCC 4.6 warning
  arch/arm/cpu/arm926ejs/omap/cpuinfo.c: Fix GCC 4.6 warnings
  drivers/net/lan91c96.c: Fix GCC 4.6 warning
  board/ronetix/pm9263/pm9263.c: Fix GCC 4.6 warning
  drivers/mtd/onenand/samsung.c: Fix GCC 4.6 warning
  drivers/usb/musb/musb_hcd.c: Fix GCC 4.6 warning

Fix:
davinci_i2c.c: In function 'flush_rx':
davinci_i2c.c:81:6: warning: variable 'dummy' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>

There are some magic constants in this drivers, which I cannot
fixup ... Eran, can you help here?

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Eran Man <eran@nbase.co.il>

This supports I2C of Renesas SH.
I tested on SH7724.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>

Fix:
dnet.c: In function 'dnet_send':
dnet.c:136:9: warning: variable 'len' set but not used
[-Wunused-but-set-variable]
dnet.c: In function 'dnet_set_hwaddr':
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
flash.c: In function 'flash_erase':
flash.c:223:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:392:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
bootp.c: In function 'BootpCopyNetParams':
bootp.c:108:11: warning: unused variable 'tmp_ip' [-Wunused-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
cmd_bootm.c: In function 'bootm_load_os':
cmd_bootm.c:315:7: warning: unused variable 'unc_len'
[-Wunused-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
mx1ads.c: In function 'board_early_init_f':
mx1ads.c:83:24: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
syncflash.c: In function 'SF_SR':
syncflash.c:60:10: warning: variable 'tmp1' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'SF_PrechargeAll':
syncflash.c:96:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
mx1ads.c: In function 'board_early_init_f':
mx1ads.c:83:24: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'SF_Erase':
syncflash.c:112:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'flash_init':
syncflash.c:155:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
flash.c: In function 'flash_erase':
flash.c:223:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:392:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
cs8900.c: In function 'get_reg_init_bus':
cs8900.c:69:14: warning: variable 'c' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
cpuinfo.c: In function 'print_cpuinfo':
cpuinfo.c:155:6: warning: variable 'system_serial_low' set but not used
[-Wunused-but-set-variable]
cpuinfo.c:154:6: warning: variable 'system_serial_high' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
lan91c96.c: In function 'dump_memory_info':
lan91c96.c:157:7: warning: variable 'mem_info' set but not used
[-Wunused-but-set-variable]
lan91c96.c: In function 'smc_send_packet':
lan91c96.c:320:16: warning: variable 'ioaddr' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
pm9263.c: In function 'pm9263_lcd_hw_psram_init':
pm9263.c:167:20: warning: variable 'x' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
samsung.c: In function 's3c_onenand_check_lock_status':
samsung.c:486:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix:
musb_hcd.c: In function 'submit_control_msg':
musb_hcd.c:851:6: warning: variable 'csr' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>

NDS32 and SANDBOX architecture were sharing the same IH_ARCH number

Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Acked-by: Macpaul Lin <macpaul@andestech.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>

Remove unneccessary codes.
1. Clean up for cpu related code.
2. Clean up for timer related code.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>

Instead of linking the file into $(obj) tree use directly the source file.
This also prevents littered source tree if building not out-of-tree.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

This fixes a few printf() strings for size_t which are missing the 'z'
modifier.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>

device is already in *normal* (D0) mode => it doesn't need to be wake-up.

With this patch, we only wake-up (writing on TEST_BYTE register) if PM_MODE
bits of PM_CTRL register is in sleep (D1/D2) mode.

Signed-off-by: Bertrand Cachet <bertrand.cachet@heig-vd.ch>

Cleanup the env_common.c checkpatch warnings, errors and coding style.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_nand.c checkpatch warnings, errors and coding style.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_flash.c checkpatch warnings, errors and coding style.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_sf.c checkpatch warnings, errors and coding style.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_eeprom.c checkpatch warnings, errors and coding style.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_embedded.c checkpatch warnings, errors and coding style.
There is one error left though:
 ERROR: Macros with multiple statements should be enclosed in a do - while loop
 #79: FILE: u-boot/common/env_embedded.c:79:
 +#define GEN_ABS(name, value)                   \
 +       asm(".globl " GEN_SYMNAME(name));       \
 +       GEN_SET_VALUE(name, value)

 total: 1 errors, 0 warnings, 213 lines checked

We cannot enclose that statement in a do - while loop,
because these are a global assembly declarations.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_mmc.c checkpatch warnings, errors and coding style.
Simplify env_relocate_spec() function implementation.
Also mark internal functions as static.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_nvram.c checkpatch warnings, errors and coding style.
There are 2 wanring left about the extern used in c file:
 WARNING: externs should be avoided in .c files
 #53: FILE: env_nvram.c:53:
 +extern void *nvram_read(void *dest, const long src, size_t count);

 WARNING: externs should be avoided in .c files
 #54: FILE: env_nvram.c:54:
 +extern void nvram_write(long dest, const void *src, size_t count);

 total: 0 errors, 2 warnings, 138 lines checked

There is no common nvram header file to use instead of the externs.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Cleanup the env_onenand.c checkpatch warnings, errors and coding style.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>