- Nov 11, 2014
-
-
Peter Crosthwaite authored
Add a defconfig and Kconfigury for the Digilent ZYBO board. Signed-off-by:
Peter Crosthwaite <crosthwaite.peter@gmail.com> Acked-by:
Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Reviewed-by:
Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by:
Michal Simek <michal.simek@xilinx.com>
-
Tinghui Wang authored
This patch adds config support needed for ZYBO target and has been tested on Rev. B ZYBO hardware. Signed-off-by:
Tinghui Wang <steven.wang@digilentinc.com> [PC changes: * Dropped boards.cfg change (rebase conflict) * Dropped custom u-boot env * Added DTS * Misc forward-porting changes ] Signed-off-by:
-
Peter Crosthwaite authored
It's a Zynq board similar in design to the currently supported ones. 512MB of RAM and UART1 is used. Signed-off-by:
-
Soren Brinkmann authored
The latest Xilinx tools generate ps7_init files that are explicitly available under GPL. Change the makefile to allow drop in of those files for building the SPL. Signed-off-by:
Soren Brinkmann <soren.brinkmann@xilinx.com> Acked-by:
Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Reviewed-and-tested-by:
-
- Nov 05, 2014
-
-
git://www.denx.de/git/u-boot-shTom Rini authored
-
git://www.denx.de/git/u-boot-imxTom Rini authored
-
Nikita Kiryanov authored
The 1GB DRAM configuration on mx6 solo uses 2 chip selects, but the code tests 1GB DRAM configuration as if it is all present on one chip select, and thus cannot see the full range of available memory. Refactor the check to detect 1GB DRAM correctly. Signed-off-by:
Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Acked-by:
Igor Grinberg <grinberg@compulab.co.il>
-
Nikita Kiryanov authored
Change the order in which GPIOs are toggled in SATA init sequence to accomodate both SanDisk and Phison SSDs. Signed-off-by:
-
-
-
Hans de Goede authored
This is necessary for the device-model enabled builds to work properly. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Simon Glass <sjg@chromium.org>
-
Hans de Goede authored
This is necessary for the device-model enabled builds to work properly. Signed-off-by:
-
Simon Glass authored
Add a driver for the designware serial UART used on sunxi. This just redirects to the normal ns16550 driver. Add a stdout-path to the device tree so that the correct UART is chosen. Signed-off-by:
-
Simon Glass authored
This adds driver model support to the sunxi GPIO driver, using the device tree to trigger binding of the driver. The driver will still operate without driver model too. Signed-off-by:
-
Simon Glass authored
The scsi_init() function uses a GPIO so should request it. There is no way to return an error here, and the request may be made multiple times, so just ignore errors for now. Signed-off-by:
-
Simon Glass authored
With driver model we will have access to a bank pointer, so we want to use it rather than converting back to a number, and then back to a bank pointer. Add functions to provide this feature. Signed-off-by:
-
Simon Glass authored
For now we won't want to mess with the existing configurations. Create a new one which will enable device tree and driver model. Note that this brings the device tree binary into u-boot-sunxi-with-spl.bin. Signed-off-by:
-
Simon Glass authored
These are from Linux 3.17-rc7 (commit fe82dcec). U-Boot only uses a small portion of these, but we may as well have something to look forward to. The total compiled size is about 25KB. Acked-by:
-
Ian Campbell authored
$ make BOARD_felconfig is more convenient than $ make BOARD_defconfig $ echo CONFIG_SPL_FEL=y >> .config $ echo CONFIG_SPL_FEL=y >> spl/.config Signed-off-by:Ian Campbell <ijc@hellion.org.uk> Reviewed-by:
-
Ian Campbell authored
This was done automatically with the following bits of scripting. The Kconfig choice content was generated with this script snippet: for i in $(git grep -l CONFIG_ARCH_SUNXI configs/*) ; do TARGET=$(sed -n -e 's/CONFIG_SYS_EXTRA_OPTIONS="\([^,"]\+\).*/\1/p' $i); MACH=$(sed -n -e 's/.*CONFIG_\(MACH_SUN.I\)=./\1/p' $i) echo "config TARGET_$TARGET" echo " bool \"$TARGET\"" echo " depends on $MACH" echo done defconfigs were updated with a sed script (t): # Extract board from first entry of CONFIG_SYS_EXTRA_OPTIONS, /^CONFIG_SYS_EXTRA_OPTIONS/ { s/^\(CONFIG_SYS_EXTRA_OPTIONS="\)\([^,"]\+\),\?\(.*\)/\1\3\nCONFIG_TARGET_\2=y/; # Print and delete first line (CONFIG_SYS_EXTRA_OPTIONS), leaving # CONFIG_TARGET_<BOARD> in pattern space P;D; }; # Move CONFIG_TARGET_<BOARD> to hold space /^CONFIG_TARGET/{h;n} # Print CONFIG_TARGET_<BOARD> after CONFIG_MACH_<SOC> in either SPL or # normal mode. /^CONFIG_MACH/{p;g;p;n}; /^\+S:CONFIG_MACH/{p;g;s/^CONFIG_TARGET/+S:&/;p;n}; # Print any remaining lines normally p; Run as: sed -i -n -f t $(git grep -l CONFIG_ARCH_SUNXI configs/*) and then manually removing the one instance of CONFIG_SYS_EXTRA_OPTIONS="" from Colombus_defconfig board/sunxi/Makefile was updated with: sed -e 's/^\(obj-\$(CONFIG_\)\(.*\)\().*+= dram_.*\)/\1TARGET_\2\3/g' board/sunxi/Makefile and manually retabbing a few lines to line up again. The board descriptions could certainly be improved. Signed-off-by: -
Ian Campbell authored
This can now be configured via Kconfig, e.g. with: $ make BOARD_defconfig $ echo CONFIG_SPL_FEL=y >> .config $ echo CONFIG_SPL_FEL=y >> spl/.config Signed-off-by: -
Ian Campbell authored
Mostly automatic with: sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I) followed by removing the relevant #defines from include/configs/sun?i.h by hand. Signed-off-by: -
Ian Campbell authored
It's unfortunate that this needs to be present in both .config and spl/.config since it makes it slightly hard to enable FEL mode for a regular defconfig. It can be done with: echo CONFIG_SPL_FEL=y >> .config echo CONFIG_SPL_FEL=y >> spl/.config Ideally only one of those would be needed. Signed-off-by: -
Ian Campbell authored
Now we have CONFIG_ARCH_SUNXI as the toplevel, CONFIG_MACH_SUN[45678]I as the per-SoC option and leave CONFIG_TARGET_BLAH free for individual boards in the future. Done automatically with: sed -i -e 's/TARGET_\(SUN[45678]I\)/MACH_\1/g' $(git grep -l TARGET_SUN[45678]I) Signed-off-by: -
Ian Campbell authored
And make TARGET_SUN[45678]I a choice variable under this. configs updated with: sed -i -e 's/^\(\+S:\)\?CONFIG_TARGET_SUN.I=y/\1CONFIG_ARCH_SUNXI=y\n&/g' configs/* Signed-off-by: -
Chen-Yu Tsai authored
The defconfig for Ippo-q8h-v5 was incorrectly committed as "Ippo_q8h". This patch renames it correctly, as well as correct a typo in my name in the maintainers listing. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Acked-by:
-
Dirk Eibach authored
I realized that with v2014.10 u-boot is not starting up on ppc4xx boards with CONFIG_SYS_GENERIC_BOARD set. I bisected it down to this: d54d7eb9 support blackfin board initialization in generic board_f With d29437aa ppc: Make ppc4xx ready for CONFIG_SYS_GENERIC_BOARD I set gd to a defined value for ppc4xx in cpu_init_f(). I did not realize that the gd struct has also to be memset() to zero at this point. But at least commit d54d7eb9 assumes it is: @@ -516,11 +528,13 @@ static int reserve_malloc(void) /* (permanently) allocate a Board Info struct */ static int reserve_board(void) { - gd->start_addr_sp -= sizeof(bd_t); - gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t)); - memset(gd->bd, '\0', sizeof(bd_t)); - debug("Reserving %zu Bytes for Board Info at: %08lx\n", - sizeof(bd_t), gd->start_addr_sp); + if (!gd->bd) { + gd->start_addr_sp -= sizeof(bd_t); + gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t)); + memset(gd->bd, '\0', sizeof(bd_t)); + debug("Reserving %zu Bytes for Board Info at: %08lx\n", + sizeof(bd_t), gd->start_addr_sp); + } return 0; } #endif This might also be an issue on other architectures, so maintainers should check. Signed-off-by:
Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by:
Stefan Roese <sr@denx.de>
-
- Nov 04, 2014
-
-
git://git.denx.de/u-boot-shTom Rini authored
-
Gerald Kerma authored
This patch fix the kwimage tools for version 0 fileformat used for kirkwood Tested on sheevaplug Signed-off-by:
Gerald Kerma <drEagle@doukki.net> Tested-by:
Prafulla Wadaskar <prafulla@marvell.com>
-
Igor Grinberg authored
Trivial fix (unless Pantelis has a new email address): Pantelis Antoniou <panto.antoniou-consulting.com> ^ make it: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: -
Vagrant Cascadian authored
* Escape use of - in description of -F. * Fix line continuations in examples so that the continued lines are also bold. Signed-off-by:Vagrant Cascadian <vagrant@debian.org>
-
Masahiro Yamada authored
These lines originate in Linux; it looks like Linux folks chose to hide bunch of warnings reported by clang rather than fixing C code. In U-boot, warnings are being fixed thanks to Jeroen's great efforts. Let's stop suppressing clang warnings. Signed-off-by: -
Masahiro Yamada authored
Defining CONFIG_SYS_TEXT_BASE in config.mk is very old style. Create CONFIG_SYS_TEXT_BASE option in Kconfig, but let it depend on CONFIG_SPARC because we do not want to disturb the other architectures that still define CONFIG_SYS_TEXT_BASE in their header files. Signed-off-by: -
Masahiro Yamada authored
For now, all the SPARC boards in U-Boot are provided by Gaisler. Signed-off-by: -
Masahiro Yamada authored
Remove arch/sparc/cpu/{leon2,leon3}/config.mk and move duplicated defines of -fPIC to arch/sparc/config.mk. Signed-off-by: -
Masahiro Yamada authored
Signed-off-by: -
Masahiro Yamada authored
The Board names in the board select menu were simply taken from the board directory name by a conversion tool when switching to Kconfig. Let's use more descriptive prompts taken from include/configs/gr*.h and board/gaisler/*/config.mk. Signed-off-by: -
Jeroen Hofstee authored
While at it, sort them. Cc: Tom Rini <trini@ti.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by:Jeroen Hofstee <jeroen@myspectrum.nl>
-
Jeroen Hofstee authored
Cc: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: -
Jeroen Hofstee authored
Cc: Heiko Schocher <hs@denx.de> Signed-off-by:
-
