Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>

The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.

This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Enable DM_PWM and DM_REGULATOR on rockchip SoCs.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

Compared to the Armada 3700, the Armada 7K and 8K are much more on the
high-end side: they use a dual Cortex-A72 or a quad Cortex-A72, as
opposed to the Cortex-A53 for the Armada 3700.

The Armada 7K and 8K also use a fairly unique architecture, internally
they are composed of several components:

- One AP (Application Processor), which contains the processor itself
  and a few core hardware blocks. The AP used in the Armada 7K and 8K
  is called AP806, and is available in two configurations:
  dual Cortex-A72 and quad Cortex-A72.
- One or two CP (Communication Processor), which contain most of the I/O
  interfaces (SATA, PCIe, Ethernet, etc.). The 7K family chips have one
  CP, while the 8K family chips integrate two CPs, providing two times
  the number of I/O interfaces available in the CP.
  The CP used in the 7K and 8K is called CP110.

All in all, this gives the following combinations:

- Armada 7020, which is a dual Cortex-A72 with one CP
- Armada 7040, which is a quad Cortex-A72 with one CP
- Armada 8020, which is a dual Cortex-A72 with two CPs
- Armada 8040, which is a quad Cortex-A72 with two CPs

This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support,
starting with the Marvell DB-88F7040 development board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>

The Armada 3700 integrates the following interfaces (not complete list):
- Dual Cortex-A53 ARMv8
- USB 3.0
- SATA 3.0
- PCIe 2.0
- 2 x Gigabit Ethernet 1Gbps / 2.5Gbps
- ...

This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support
for the Marvell DB-88F3720 development board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>

Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>

Move this config to Kconfig option and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

As I repeated in the ML, I am unhappy with config entries with bare
defaults.  Kick them out of arch/arm/mach-uniphier/Kconfig.

Currently, CONFIG_SPL_SERIAL_SUPPORT is not user-configurable
(build fails without it), but it should be fixed later anyway,
so I am moving CONFIG_SPL_SERIAL_SUPPORT to defconfigs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Select DM_USB to compatible with USB DM driver model.

Signed-off-by: MengDongyang <daniel.meng@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

Now all UniPhier SoCs support a pinctrl driver.  Select (SPL_)PINCTRL
since it is mandatory even for base use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

LS1046AQDS Specification:
-------------------------
Memory subsystem:
 * 8GByte DDR4 SDRAM (64bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 64 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * Two XFI 10G ports
 * Two SGMII ports
 * Two RGMII ports

PCIe: supports Gen 1 and Gen 2

SATA 3.0: one SATA 3.0 port

USB 3.0: two micro AB connector and one type A connector

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

LS1046ARDB Specification:
-------------------------
Memory subsystem:
 * 8GByte DDR4 SDRAM (64bit bus)
 * 512 Mbyte NAND flash
 * Two 64 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card
 * On-board 4G eMMC

Ethernet:
 * Two XFI 10G ports
 * Two SGMII ports
 * Two RGMII ports

PCIe:
 * PCIe1 (SerDes2 Lane0) to miniPCIe slot
 * PCIe2 (SerDes2 Lane1) to x2 PCIe slot
 * PCIe3 (SerDes2 Lane2) to x4 PCIe slot

SATA:
 * SerDes2 Lane3 to SATA port

USB 3.0: one super speed USB 3.0 type A port
	 one Micro-AB port

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

This is the state-of-the-art MMC driver implementation.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This driver has not been converted to Driver Model, and it is an
obstacle to migrate other block device drivers.  Remove it for now.

The UniPhier SoCs already use a DM-based EHCI driver, so now
ARCH_UNIPHIER can select DM_USB.

These two changes must be done atomically because removing the
legacy driver causes a build error.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>

ARCH_UNIPHIER is having more and more select:s.  Sort them in case
a select is accidentally duplicated.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

We are supposed to not add config entries with only "default y"
in board/SoC Kconfig files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>

Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select.  Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.

Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Use a tab not 8 spaces.

Signed-off-by: Tom Rini <trini@konsulko.com>

This series moves the CONFIG_SYS_CACHELINE_SIZE.  First, in nearly all
cases we are mirroring the values used by the Linux Kernel here.  Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux).  Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Paul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: "Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Chin Liang See <clsee@altera.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Kocialkowski <contact@paulk.fr>

This creates Kconfig of R-Car 32bit for Kconfig of R-Car 64bit (Gen3).

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Move from arch/arm/cpu/armv7/rmobile/ to arch/arm/mach-rmobile/.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

In the case of omap3 we have a number of platforms that are close to
exceeding SRAM limits, depending on compiler.  Move to USE_TINY_PRINTF
to give them more room.  OMAP4 will soon enough be in a similar place,
so enable that now.

Signed-off-by: Tom Rini <trini@konsulko.com>

In reality all omap3 platforms support SPL so move the select for this
up a level.

Signed-off-by: Tom Rini <trini@konsulko.com>

We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system.  Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.

Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.

I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable.  However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones.  I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.

CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.

Fixes: 95ebc253 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>

The patch:
"dm: mmc: zynq: Convert zynq to use driver model for MMC"
(sha1: 329a449f)
added dependency on enabling some MMC options by default.
There are minimal ZynqMP configurations which require
only minimal configurations to be enabled to keep u-boot size
as lower as possible.

Move options to defconfig instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Move zynq to the latest driver model support by enabling CONFIG_DM_MMC,
CONFIG_DM_MMC_OPS and CONFIG_BLK.

Signed-off-by: Simon Glass <sjg@chromium.org>

Convert zynq USB to driver model. Note this is tested on zynq-zybo only.

Signed-off-by: Simon Glass <sjg@chromium.org>

RK3399 is a SoC from Rockchip with dual-core Cortex-A72
and quad-core Cortex-A53 CPU. It supports two USB3.0
type-C ports and two USB2.0 EHCI ports. Other interfaces
are very much like RK3288, the DRAM are 32bit width address
and support address from 0 to 4GB-128MB range.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

In preparation for RK3368 and RK3399, which need to select ARM64, don't
select CPU_V7 at the ARCH_ROCKCHIP level but at the SoC level instead.

Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>

Serial driver starts to use clk framework that's why
enable it by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable this option to move rockchip over to use driver model for MMC
operations.

Signed-off-by: Simon Glass <sjg@chromium.org>

Rockchip uses driver model for all subsystems. Specify this in the arm
Kconfig rather than as defaults in the Rockchip Kconfig. This means that
boards cannot turn these options off, which seems correct.

Signed-off-by: Simon Glass <sjg@chromium.org>

Rename B&R kwb board to brxre1

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>

Rename B&R tseries board to brppt1

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>

DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.

The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.

The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.

For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

This gives us a bit more breathing room wrt our SPL size.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>

The DRAM PHY layer on PH1-LD20 is able to calibrate PHY parameters
periodically.  This compensates for the voltage and temperature
deviation and improves the PHY parameter adjustment.  Instead, it
requires 64 byte scratch memory in each DRAM channel for the dynamic
training.  The memory regions must be reserved in DT before jumping
to the kernel.

The scratch area can be anywhere in each DRAM channel, but the DRAM
init code in SPL currently assigns it at the end of each channel.
So, it makes sense to reserve the regions on run-time by U-Boot
instead of statically embedding it in the DT in Linux.  Anyway,
a boot-loader should know much more about memory initialization
than the kernel.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>