palmas/TWL6035 is power IC for omap5 evm boards

Signed-off-by: Balaji T K <balajitk@ti.com>

In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

The ddr part name used in OMAP5 ES1.0 soc is a SAMSUNG part and
not a ELPIDA part. So change this.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

Adding the nessecary changes for OMAP5430 ES1.0 silicon.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

Add support to identify the device as GP/EMU/HS.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

The break statement is missing in init_omap_revision function, resulting
in a wrong revision identification. So fixing this.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.

Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
	http://lists.denx.de/pipermail/u-boot/2012-March/119151.html



Signed-off-by: R Sricharan <r.sricharan@ti.com>

The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

The control module provides options to set various signal
integrity parameters like the output impedance, slew rate,
load capacitance for different pad groups. Configure these
as required for the omap5430 sevm board.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

Adding the full pinmux data for OMAP5430 sevm board.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

This is rework on config files of IGEP-based boards with the aim to remove
duplicated code to be more maintainable. Basically this patch creates a
common configuration file for both boards and only sets the specific option
in the board config file.

On board files the hardcored mach type was replaced in favour of using the
CONFIG_MACH_TYPE option.

More than 200 duplicated lines have been deleted.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>

OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.

As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
                           |---------------| (SET1 default 1.4V)
                           |               --------(programmed voltage)
                           | <- (This switch happens on mux7,pullup)
vdd_mpu(TPS)         -----/ (OPP boot voltage)
                                             --------- (programmed voltage)
vdd_core(TWL6030)    -----------------------/ (OPP boot voltage)
Problem 1)                |<----- Tx ------>|
   timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.

By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
                                  -------- (programmed voltage)
vdd_mpu(TPS)         ------------/ (Opp boot voltage)
                                   --------- (programmed voltage)
vdd_core(TWL6030)    -------------/ (OPP boot voltage)

NOTE: This does not attempt to address OMAP5 - Aneesh please confirm

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.

With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.

NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency.  While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board.  The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.

Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>

This patch adds support for Cloud Engines Pogoplug E02

Information regarding the CE Pogoplug E02 board can be found at:
http://archlinuxarm.org/platforms/armv5/pogoplug-v2-pinkgray



Signed-off-by: Dave Purdy <david.c.purdy@gmail.com>
Cc: prafulla@marvell.com
Cc: albert.u.boot@aribaud.net

Add support for new boards RaidSonic ICY BOX NAS6210 and NAS6220.

NAS6210 has 1 SATA and 1 eSATA port while NAS6220 has 2 SATA ports.

More information about the boards can be found here:

http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7036
http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7515



Signed-off-by: Luka Perkov <uboot@lukaperkov.net>
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>

This change adds a basic support for Embest/Timll DevKit3250 board,
NOR and UART are the only supported peripherals for a moment. The board
doesn't require low-level init, because the initial SDRAM and GPIO
configuration is performed during kickstart bootloader execution.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>

This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>

This change adds initial support for NXP LPC32x0 SoC series.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>

I have tested booting both FDT and non-FDT based Linux kernels (based on
http://marc.info/?l=linux-arm-kernel&m=133002679716986 and
http://marc.info/?l=linux-arm-kernel&m=132328894303581

 respectively).

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Jason <jason@lakedaemon.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>

* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
  lin_gadget: use common linux/compat.h
  linux/compat.h: rename from linux/mtd/compat.h
  lin_gadget: use common mdelay
  gunzip: rename z{alloc, free} to gz{alloc, free}
  fs/fat: align disk buffers on cache line to enable DMA and cache
  part_dos: align disk buffers on cache line to enable DMA and cache

* 'master' of /home/wd/git/u-boot/custodians:
  powerpc/ppc4xx: Remove typedefs for gdsys FPGA
  powerpc/ppc4xx: Fix typo in gdsys_fpga.h
  powerpc/ppc4xx: Update gdsys board configurations
  powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
  powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
  powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
  powerpc/ppc4xx: Adjust environment size on neo

* 'master' of git://git.denx.de/u-boot-ppc4xx:
  powerpc/ppc4xx: Remove typedefs for gdsys FPGA
  powerpc/ppc4xx: Fix typo in gdsys_fpga.h
  powerpc/ppc4xx: Update gdsys board configurations
  powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
  powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
  powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
  powerpc/ppc4xx: Adjust environment size on neo

Merge our duplicate definitions with the common header.

Also fix drivers/usb/gadget/s3c_udc_otg_xfer_dma.c to
use min() instead of min_t() since we remove the latter
from compat.h.

Additionally use memalign() directly as the lin_gadget
specific kmalloc() macro is removed from lin_gadget_compat.h
by this patch.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>

This lets us use it in more places than just mtd code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No need to provide our own mdelay() macro when we have a func for it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This allows us to add a proper zalloc() func (one that does a zeroing
alloc), and removes duplicate prototypes.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

The MAKEALL script cleverly runs make with the appropriate options
to use all of the cores on the system, but your average U-Boot build
can't make much use of more than a few cores.  If you happen to have
a many-core server, your builds will leave most of the system idle.

In order to make full use of such a system, we need to build multiple
targets in parallel, and this requires directing make output into
multiple directories. We add a BUILD_NBUILDS variable, which allows
users to specify how many builds to run in parallel.
When BUILD_NBUILDS is set greater than 1, we redefine BUILD_DIR for
each build to be ${BUILD_DIR}/${target}. Also, we make "./build" the
default BUILD_DIR when BUILD_NBUILDS is greater than 1.

MAKEALL now tracks which builds are still running, and when one
finishes, it starts a new build.

Once each build finishes, we run "make tidy" on its directory, to reduce
the footprint.

As a result, we are left with a build directory with all of the built
targets still there for use, which means anyone who wanted to use
MAKEALL as part of a test harness can now do so.

Signed-off-by: Andy Fleming <afleming@freescale.com>

* 'master' of /home/wd/git/u-boot/custodians:
  powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
  powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
  cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
  PowerPC: correct the SATA for p1/p2 rdb-pc platform
  powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
  powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
  powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
  powerpc/corenet_ds: Slave module for boot from SRIO
  powerpc/corenet_ds: Master module for boot from SRIO
  powerpc/corenet_ds: Document for the boot from SRIO
  powerpc/corenet_ds: Correct the compilation errors about ENV
  powerpc/srio: Rewrite the struct ccsr_rio
  powerpc/85xx:Fix lds for nand boot debug info
  powerpc/p2041rdb: add env in NAND support
  powerpc/p2041rdb: add NAND and NAND boot support
  powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
  powerpc/85xx:Avoid vector table compilation for nand_spl
  powerpc/85xx:Fix IVORs addr after vector table relocation
  powerpc/85xx:Avoid hardcoded vector address for IVORs
  powerpc/p1023rds: Disable nor flash node and enable nand flash node

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
  powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
  cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
  PowerPC: correct the SATA for p1/p2 rdb-pc platform
  powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
  powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
  powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
  powerpc/corenet_ds: Slave module for boot from SRIO
  powerpc/corenet_ds: Master module for boot from SRIO
  powerpc/corenet_ds: Document for the boot from SRIO
  powerpc/corenet_ds: Correct the compilation errors about ENV
  powerpc/srio: Rewrite the struct ccsr_rio
  powerpc/85xx:Fix lds for nand boot debug info
  powerpc/p2041rdb: add env in NAND support
  powerpc/p2041rdb: add NAND and NAND boot support
  powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
  powerpc/85xx:Avoid vector table compilation for nand_spl
  powerpc/85xx:Fix IVORs addr after vector table relocation
  powerpc/85xx:Avoid hardcoded vector address for IVORs
  powerpc/p1023rds: Disable nor flash node and enable nand flash node

* 'master' of /home/wd/git/u-boot/custodians:
  i2c:designware Turn off the ctrl when setting the speed
  i2c: Add support for designware i2c controller
  sh: i2c: Add support I2C controller of SH7734

* 'master' of git://git.denx.de/u-boot-i2c:
  i2c:designware Turn off the ctrl when setting the speed
  i2c: Add support for designware i2c controller
  sh: i2c: Add support I2C controller of SH7734