- Dec 16, 2016
-
-
Jagan Teki authored
Add .read_rom_hwaddr on dm eth_ops. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by:
Joe Hershberger <joe.hershberger@ni.com> Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com>
-
Jagan Teki authored
- Remove exctra space - Add space - Add tab space - Fix single line comments quotes - Fix 'CHECK: Avoid CamelCase' - Fix 'CHECK: Alignment should match open parenthesis' - Fix 'WARNING: line over 80 characters' - Re-arrage header include files Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by:
-
Jagan Teki authored
This patch add driver model support for fec_mxc driver. Cc: Simon Glass <sjg@chromium.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by:
-
Jagan Teki authored
fec_get_hwaddr never used eth_device argument, hence removed. Cc: Simon Glass <sjg@chromium.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Michael Trimarchi <michael@amarulasolutions.com> Acked-by:
-
Patrick Bruenn authored
Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by:Patrick Bruenn <p.bruenn@beckhoff.com>
-
Peng Fan authored
Add plugin support for mx6sllevk board. Signed-off-by:Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
Peng Fan authored
Add i.MX6SLL EVK board support. 1. Add imx6sll-evk device tree. 2. Enable SDHC/I2C/UART. 3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver. Boot Log: U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800) CPU: Freescale i.MX6SLL rev1.0 at 792MHz CPU: Commercial temperature grade (0C to 95C)Reset cause: POR Model: Freescale i.MX6SLL EVK Board Board: MX6SLL EVK DRAM: 2 GiB i2c bus 0 at 35258368, no gpio pinctrl state. PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: -
Peng Fan authored
Add i.MX6SLL device tree. Signed-off-by: -
Peng Fan authored
There two iomuxc for i.MX6SLL. One is normal IOMUXC, the other is for IOMUXC_SNVS. Signed-off-by:
Simon Glass <sjg@chromium.org>
-
Peng Fan authored
Update lcdif regs for i.MX6SL/SLL Signed-off-by:
Ye.Li <ye.li@nxp.com> Signed-off-by:
-
Peng Fan authored
Add the i.MX6SLL support to OCOTP driver. The i.MX6SLL reuses the i.MX6ULL fuse, bank 7 and bank8 have 4 words each, and there is a hole between bank 5 and bank 6. Signed-off-by:
-
Peng Fan authored
Correct loadaddr and text base for i.MX6SLL Signed-off-by: -
Peng Fan authored
add Kconfig entry for i.MX6SLL Signed-off-by: -
Peng Fan authored
If L2 cache configured as OCRAM, reset it. Switch to use runtime check. Signed-off-by: -
Peng Fan authored
Add clock support for i.MX6SLL. Signed-off-by: -
Peng Fan authored
The LCDIF Pixel clock mux is not glitchless, so need to gate before changing mux. Also change enable_lcdif_clock prototype with a new input parameter to indicate disable or enable. Signed-off-by: -
Peng Fan authored
Add lcdif clock support for i.MX6SL. Signed-off-by: -
Peng Fan authored
The mux for the lcd clock is not glitchless, so need to first gate the clock before changing the mux. Signed-off-by: -
Peng Fan authored
>From RM, per_periph2_clk_sel option3 is: "derive clock from 198MHz clock (divided 392MHz PLL2 PFD)." So fix it. Signed-off-by: -
Peng Fan authored
Add iomux settings for i.MX6 SLL Signed-off-by:
-
Peng Fan authored
Add i.MX6 SLL GPT timer support. Signed-off-by: -
Peng Fan authored
Update register address for i.MX6 SLL Signed-off-by: -
Peng Fan authored
Add i.MX6SLL pinmux header files Signed-off-by: -
Peng Fan authored
Add i.MX6SLL cpu type. MXC_CPU_MX6D is not a real value in chip, so change it to 0x6A. Signed-off-by: -
Sanchayan Maity authored
u-boot allows modifying a device tree after it is loaded into memory. Add fdt_fixup hook in u-boot environment which can facilitate such modifications. Signed-off-by:Sanchayan Maity <maitysanchayan@gmail.com>
-
Marcin Niestroj authored
liteBoard is a development board which uses liteSOM as its base. Hardware specification: * liteSOM (i.MX6UL, DRAM, eMMC) * Ethernet PHY (id 0) * USB host (usb_otg1) * MicroSD slot (uSDHC1) Signed-off-by:Marcin Niestroj <m.niestroj@grinn-global.com>
-
Marcin Niestroj authored
liteSOM is a System On Module (http://grinn-global.com/litesom/ ). It can't exists on its own, but will be used as part of other boards. Hardware specification: * NXP i.MX6UL processor * 256M or 512M DDR3 memory * optional eMMC (uSDHC2) Here we treat SOM similar to SOC, so we place it inside arch/arm/mach-* directory and make it possible to reuse initialization code (i.e. DDR, eMMC init) for all boards that use it. Signed-off-by:
-
Breno Lima authored
UDOO Neo boards has one FEC port connected to KSZ8091, add support for it. Tested on a UDOO Neo Full with "dhcp zImage" command. Signed-off-by:Breno Lima <breno.lima@nxp.com>
-
Breno Lima authored
UDOO Neo boards has a PFUZE300 connected to I2C1 bus. Tested on a UDOO Neo Full with "pmic PFUZE3000 dump" command. Signed-off-by: -
Breno Lima authored
Add pfuze3000 voltage configuration macro for SW1AB, SW3 and VLDO1/2 according to tables 53, 57 and 62 on PF3000 datasheet. Signed-off-by: -
Breno Lima authored
Add thermal support on the Kconfig file. Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com>
-
Breno Lima authored
It's not necessary to define the console option as we use the distro config. Signed-off-by:
-
Breno Lima authored
It's not necessary to define the mmcautodetect as it is not used anywhere. Signed-off-by:
-
Breno Lima authored
Change board_string() function to static because it's being used locally. Signed-off-by:
-
Breno Lima authored
It's not necessary to define the processor in the defconfig file. The preferred method to select the SoC is via Kconfig file. Signed-off-by:
-
Breno Lima authored
It's not necessary to support USDHC3 in U-Boot as it's being used for the WLAN. Signed-off-by:
-
Max Krummenacher authored
This adds board support for the Toradex module family Colibri iMX6. The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both with a version for commercial and industrial temperature range. Signed-off-by:Max Krummenacher <max.krummenacher@toradex.com>
-
Max Krummenacher authored
This adds board support for the Toradex module family Apalis iMX6. The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with commercial and industrial temperature range. Signed-off-by: -
Stefan Agner authored
Add proper reg values for the two AIPS bus nodes. This avoids this two warnings: Node /soc/aips-bus@40000000 has a unit name, but no reg property Node /soc/aips-bus@40080000 has a unit name, but no reg property Signed-off-by:Stefan Agner <stefan.agner@toradex.com>
-
Stefan Agner authored
Currently a divider of 6 has been used, leading to following NAND Flash Controller (NFC) clocks: VF61: 27.7 MHz (166.7MHz bus clock) VF50: 22 MHz (132MHz bus clock) The NAND Flash Memory used on VF50 allows to use clock speed of up to 33MHz, while the Flash Memory of VF61 allows 50MHz. We can use the same divider of 4 on both modules to configure the maximal possible clock speeds: VF61: 41.7 MHz VF50: 33 MHz Signed-off-by:
-
