- Mar 06, 2019
-
-
Troy Kisky authored
Signed-off-by:Troy Kisky <troy.kisky@boundarydevices.com>
-
Troy Kisky authored
Signed-off-by:
-
- Mar 02, 2019
-
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by:
-
- Mar 01, 2019
-
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by:
-
- Feb 26, 2019
-
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by:
-
- Feb 20, 2019
-
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by:
-
- Feb 08, 2019
-
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by:
-
- Feb 06, 2019
-
-
Troy Kisky authored
Signed-off-by:
-
- Feb 05, 2019
-
-
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Troy Kisky authored
Signed-off-by: -
Ye Li authored
The HS400 ES (Enhanced Strobe) has been added. This patch addes support for HS400 for eMMC 5.0 devices. It needs tuning at HS200 to synchronize command response. Signed-off-by:
Ye Li <ye.li@nxp.com> Reviewed-by:
Peng Fan <peng.fan@nxp.com> Signed-off-by:
-
Peng Fan authored
Add HS400 ES mode support. The flow is same as mmc_select_hs400es in kernel drivers/mmc/core/mmc.c. With HS400 ES, there is no tuning needed. With Toshiba 32GB Automotive eMMC5.1 on 8QXP ARM2 board, speed test: 'time mmc read 0x90000000 0 0x200000' shows that speed is 282MB/s. Signed-off-by:
-
Peng Fan authored
Add SD/MMC legacy capability. Otherwise the legacy cards supports will be broken. Signed-off-by: -
Jean-Jacques Hiblot authored
Add a new callback function *card_busy* which can be used to check if the card is busy. This is useful during UHS voltage switching to check if the switch was successful. Not all controllers may support this, so it's optional and when not provided the card is deemed ready. Signed-off-by:Jean-Jacques Hiblot <jjhiblot@ti.com>
-
Kishon Vijay Abraham I authored
Add a new callback function *set_vdd* which can be used by the platform mmc driver to enable or disable vdd. The mmc core can use *mmc_set_vdd* in order to invoke the callback function. This will be used during power cycle where the specification requires vdd to be disabled for 1ms and enabled again. Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Troy Kisky authored
Signed-off-by:
-
