Clarified that conversion is to DRAM clocks rather than platform clocks.
Made function static to spd_sdram.c.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>

Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>

Some device trees have a mac-address property, some have local-mac-address,
and some have both.  To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Detlev Zundel <dzu@denx.de>

G2 core reference manual says decrementer and time base
are decreasing/increasing once every 4 bus clock cycles.
Lets fix it, so time in Linux won't run twice as fast

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

What was suppose to be a stack variable was declared as a pointer,
  overwriting random memory.
Also moved the libfdt.a requirement into the main Makefile.  That is
  The U-Boot Way.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Sigend-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Now 405EZ ports also show upon bootup from which boot device
they are configured to boot:

U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)

CPU:   AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
       Bootstrap Option E - Boot ROM Location EBC (32 bits)
       16 kB I-Cache 16 kB D-Cache
Board: Acadia - AMCC PPC405EZ Evaluation Board

Signed-off-by: Stefan Roese <sr@denx.de>

Add Konstantin Kletschke for scb9328.
Signed-off-by: Peter Pearse <peter.pearse@arm.com>

U-Boot part of Lite5200b low power mode support.
Puts SDRAM out of self-refresh and transfers control to
address saved at physical 0x0.

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

Use "setter" functions instead of flags, cleaner and more flexible.
It also fixes the problem noted by Timur Tabi that the ethernet MAC
addresses were all being set incorrectly to the same MAC address.

In bootm, create the "/chosen" node only if it doesn't already exist
  (better matches the previous behavior).
Update for proper reserved memory map handling for initrd.

Set up the portmux for the MMC interface and enable the MMC driver
along with support for DOS partitions, ext2 and FAT filesystems.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs.

The AT91 ARM-based CPUs use basically the same hardware, so it should
be possible to share this driver, but no effort has been made so far.

Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682



Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Implement functions for configuring the mmci pins, as well as
functions for getting the clock rate of the mmci controller.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Include implementations of init_part() and get_partition_info() when
CONFIG_MMC is set.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>