acl: update to v2017.01
acl update to v2017.03
acl: fix scanner gpios initialization

Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>

acl: acl_q2g_defconfig add CONFIG_BLOCK_CACHE
acl_s512m: acl_s512m_defconfig add CONFIG_BLOCK_CACHE
acl: use common code for eth init
acl: eth.c now in common directory
acl: move misc_init_r/do_kbd to common
acl: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common
acl: calibrate 512m Solo board
acl: use common 1066mhz_4x256mx16.cfg
acl: add  CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs
acl: 800mhz_2x128mx16.cfg: remove _P1 accesses
acl: 800mhz_2x128mx16.cfg: use common values

CFG0: 0x40435323 to 0x3f435333
tRFC - 65 to 64 clocks
tFAW - 19 to 20 clocks

CFG1: 0xB66E8D63 to 0xb68e8b63
tRC from 20 to 21 clocks
tWR from 7 to 6 clocks

MR0: 0x13208030 to 0x15208030
tWR from 5 to 6 clocks

acl: use common ddr scripts
acl: port to v2018.07

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

nitrogen6x: delay before enabling backlight
spi_display: set mosi as write in enable_spi_rgb
nitrogen6x: add IMX_VD_A030JN01_YUV720
nitrogen6x: add hdmi vga mode
nitrogen6x: add hdmi 480p
6x_bootscript-ubuntu-3.14.txt: add imx7d support
6x_bootscript-yocto-3.14.txt: add imx7d support
nitrogen6x: prefer hannstar7 over lg1280x800
nitrogen6x: initialize GP_USB_HUB_RESET as low output
nitrogen6x: add IMX_VD38_AUO_B101EW05
nitrogen6x: add IMX_VD38_DT070BTFT
nitrogen6x: support AR8035 phy as well
Needed for new carrier with old SOM cpu card.
nitrogen6x: add CONFIG_PHY_ATHEROS
nitrogen6x: EIM_D29 high for new carrier with old som
6x_bootscript-ubuntu-3.14.txt: add rw if not using initrd
nitrogen6x: add IMX_VD38_TM070JDHG30
nitrogen6x.h: CONFIG_IPUV3_CLK 264000000
nitrogen6x: add imx6qp support for ipu priorities
nitrogen6x: ddr-setup.cfg: disable mirroring
ddr-setup.cfg: add IMX6QP support
nitrogen6x: spacing changes in environment variables
nitrogen6x: explicit fbp_detect_i2c
nitrogen6x: net_upgradeu.txt initial addition
nitrogen6x: net_upgrade_fs.txt initial addition
nitrogen6x: ubuntu/yocto add bd_addr for bluetooth mac to 6x_bootscript
nitrogen6x: add wlmac
nitrogen6x: add wlmac
nitrogen6x: verify port in board_ehci_hcd_init
nitrogen6x: use boundary.h
nitrogen6x: setup rgb_gpio_pads in board_early_init_f
nitrogen6x: add VD_KD024FM
nitrogen6x: s/board_enable_spi_rgb/board_pre_enable/
nitrogen6x: add CONFIG_SPI_FLASH_SPANSION
boundary.h: common include file initial commit
boundary: separate bootcmd so it can be overridden
6x_bootscript-ubuntu-3.14.txt: add Laci's changes(cpu/board/bootpart) and nomsi
6x_bootscript-yocto-3.14.txt: add Laci's changes(cpu/board/bootpart) and nomsi
net_upgrade_fs.txt: s/dhcp/tftp/ since ipaddr is already valid
net_upgradeu.txt: s/dhcp/tftp/ since ipaddr is already valid
6x_bootscript-*-3.14.txt: s/enable_msi/disable_msi/
6x_bootscript-*-3.14.txt: set bootargs after importing environment variable, as it may reset bootargs
net_upgrade_fs.txt: grab decompressed size from end of file
net_upgrade_fs: restructure to avoid using exit
net_upgradeu: remove offset and friends from environment
net_upgradeu_fs: initial addition
boundary: allow override of CONFIG_SF_DEFAULT_CS, make fastboot conditional on CONFIG_CI_UDC
boundary: add loglevel= environment variable
boundary: add cma= option
6x_upgrade.txt: MX25L6405D has 64k erase size
net_upgradeu.txt: MX25L6405D has 64k erase size
6x_upgrade.txt: add mx51 support
6x_bootscript*.txt: add i.mx51/i.mx53 support
net_upgrade*.txt: add i.mx51/i.mx53 support
6x_bootscript-ubuntu-3.14.txt: add loglevel
6x_bootscript-yocto-3.14.txt: add loglevel
6x_bootscript-mainline.txt: add loglevel
6x_bootscript-mainline.txt: add reset_cause
6x_bootscript-ubuntu-3.14.txt: add reset_cause
6x_bootscript-yocto-3.14.txt: add reset_cause
6x_bootscript-ubuntu-3.14.txt: add run cmd_lcd2
6x_bootscript-yocto-3.14.txt: add run cmd_lcd2
6x_upgrade: add qspi support for Nitrogen7
6x_upgrade: add qspi file checks size/tag
6x_upgrade.txt: use sfname to burn correct qspi paramter file
nitrogen6q_fl: add CONFIG_CMD_GPIO
configs: boundary: add imx51 specifics
ddr-setup.cfg: increase WALAT to 1 cycle
include/configs/boundary.h: good default for BD_CONSOLE
boundary: add fuse config needed for boards
nitrogen6x: add script linking via next variable/prog_fuses
boundary.h: allow skipping fuses
nitrogen6x: nitrogen6q_defconfig add CONFIG_BLOCK_CACHE
nitrogen6x: add CONFIG_BLOCK_CACHE to defconfigs
boundary.h: add support for i.mx53
boundary: fix CONFIG_IPUV3_CLK for imx51/imx53
boundary.h: fix build warnings when HAB enabled
nitrogen6dl2g_defconfig: remove extra define of CONFIG_SYS_EXTRA_OPTIONS
boundary: fix CONFIG_ETHPRIME(FEC0) for imx6sx
boundary: add eth.c/padctrl.h
nitrogen6x: use common code for eth init
nitrogen6x: add CONFIG_SYS_BOARD_MULTIPLE to defconfigs
boundary: eth: use mask to compare ksz9021
boundary: move eth.c to common directory
nitrogen6x: eth.c now in common directory
nitrogen6x: move misc_init_r/do_kbd to common
nitrogen6x: remove CONFIG_SYS_BOARD_MULTIPLE
	use undef CONFIG_SYS_BOARD instead
nitrogen6x: move mmc_init/ dram_init/ overwrite_console/ common_board_init/ splash_screen_prepare/ board_cfb_skip to common
nitrogen6x: const i2c_pads_info
nitrogen6x: use common 1066mhz_4x256mx16.cfg
nitrogen6x: use common 1066mhz_4x128mx16.cfg
nitrogen6x: use common 800mhz_4x128mx16.cfg
nitrogen6x: add  CONFIG_SPI_FLASH_GIGADEVICE: to defconfigs
nitrogen6x: 800mhz_2x128mx16.cfg: remove _P1 accesses
nitrogen6x: 800mhz_2x256mx16.cfg: remove _P1 accesses
nitrogen6x: 800mhz_2x128mx16.cfg: use common values

CFG0: 0x40435323 to 0x3f435333
tRFC - 65 to 64 clocks
tFAW - 19 to 20 clocks

CFG1: 0xB66E8D63 to 0xb68e8b63
tRC from 20 to 21 clocks
tWR from 7 to 6 clocks

MR0: 0x13208030 to 0x15208030
tWR from 5 to 6 clocks

nitrogen6x: 800mhz_2x256mx16.cfg: use common values

MDCFG0: from 0x696c5323 to 0x666a5333
tRFC - from 106 to 103 clocks
tXS - from 109 to 107 clocks
tFAW - from 19 to 20 clocks

MDCFG1: from 0xb66e8d63 to 0xb68e8b63
tRC - from 20 to 21 clocks
tWR - from 7 clocks to 6 clocks

MDRWD: from 0x000026d2 to 0x0f9f26d2
restore unused field to default value

MDOR: from 0x006c1023 to 0x006a1023
tXPR - from 109 to 107 clocks

MR0: from 0x13208030 to 0x15208030
tWR - from 5 to 6 clocks

nitrogen6x: 800mhz_4x256mx16.cfg: use common values

MDCFG0: from 0x696c5323 to 0x666a5333
tRFC - from 106 to 103 clocks
tXS - from 109 to 107 clocks
tFAW - from 19 to 20 clocks

MDCFG1: from 0xb66e8d63 to 0xb68e8b63
tRC - from 20 to 21 clocks
tWR - from 7 clocks to 6 clocks

MDRWD: from 0x000026d2 to 0x0f9f26d2
restore unused field to default value

MDOR: from 0x006c1023 to 0x006a1023
tXPR - from 109 to 107 clocks

MR0: from 0x13208030 to 0x15208030
tWR - from 5 to 6 clocks

nitrogen6x: use common ddr scripts
nitrogen6x: port to v2018.07
nitrogen6x: add VD_DT035BTFT panel

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

nitrogen6_lum_dl: rename board and config to nitrogen6_lum_dl1

Signed-off-by: Laci Tele <laci@boundarydevices.com>

6x_bootscript-yocto-3.14.txt: Yocto boots from zImage
6x_bootscript-*-3.14.txt: Changed address range logic for SX when dtbname set
6x_bootscript-yocto-3.14: Add check for ${board} being undefined
6x_bootscript-ubuntu-3.14: Add check for ${board} being undefined
6x_bootscript-*-3.14.txt: Add dtb support for 6QP

Signed-off-by: Ian Coolidge <ian@boundarydevices.com>

6x_bootscript-mainline: switch to zImage booting
nitrogen6x: add basic fastboot support
6x_bootscript-yocto-3.10.53: add Quad Plus dtb option
nitrogen6x: declare TC358743 interrupt as input
nitrogen6x.h: fixup update to v2017.01
boundary.h: increase fastboot buffer size
boundary.h: add secure boot options
boundary.h: fix USB host initialization
6x_bootscript-*-3.14.txt: add support for m4 specific dtb
6x_bootscript-mainline: update for new display configuration
6x_bootscript-mainline: switch to new panel naming
6x_bootscript-mainline: add support for BD070LIC2
6x_upgrade: re-introduce fs-specific load commands
nitrogen6x: update to v2017.01
nitrogen6x: update to v2017.03
6x_bootscript-mainline: change default bootdir to be /
boundary.h: add CONFIG_CMD_PART
6x_bootscript-mainline: fixup LVDS2 display handling
6x_bootscript-mainline: use UUID to identify root partition
6x_bootscript-mainline: introduce rfspart variable
fixup boundary.h for 2017.07
boundary.h: use standard config_distro_bootcmd
fixup 2 boundary.h for 2017.07
6x_bootscript-*-3.14.txt: add Silex mac address override support
6x_bootscript-yocto: remove obsolete commands
6x_bootscript-yocto: remove obsolete versions of script

Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

Declaring a CSF section makes the imximage tool increase the size of
data to be loaded by the BootROM and also adds a pointer to that CSF
section in the IVT header to the BootROM can check the signature.

Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>