davinci: omapl138_lcdk: configure ddr2

The SPL is unable to load u-boot because the DDR2 is not configured.
Configure the DDR2.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

arch/arm/mach-davinci/Kconfig

@@ -23,6 +23,7 @@ config TARGET_OMAPL138_LCDK
 	bool "OMAPL138 LCDK"
 	select SUPPORT_SPL
 	select SYS_DA850_PLL_INIT
+	select SYS_DA850_DDR_INIT
 
 config TARGET_CALIMAIN
 	bool "Calimain board"

include/configs/omapl138_lcdk.h

@@ -78,6 +78,47 @@
 #define CONFIG_SYS_DA850_PLL0_PLLM     24
 #define CONFIG_SYS_DA850_PLL1_PLLM     21
 
+/*
+ * DDR2 memory configuration
+ */
+#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
+					DV_DDR_PHY_EXT_STRBEN | \
+					(0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDBCR (		  \
+	(1 << DV_DDR_SDCR_DDR2EN_SHIFT)		| \
+	(1 << DV_DDR_SDCR_DDREN_SHIFT)		| \
+	(1 << DV_DDR_SDCR_SDRAMEN_SHIFT)	| \
+	(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT)	| \
+	(4 << DV_DDR_SDCR_CL_SHIFT)		| \
+	(3 << DV_DDR_SDCR_IBANK_SHIFT)		| \
+	(2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
+
+/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
+#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
+
+#define CONFIG_SYS_DA850_DDR2_SDTIMR (		  \
+	(19 << DV_DDR_SDTMR1_RFC_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_RP_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_RCD_SHIFT)		| \
+	(2 << DV_DDR_SDTMR1_WR_SHIFT)		| \
+	(6 << DV_DDR_SDTMR1_RAS_SHIFT)		| \
+	(8 << DV_DDR_SDTMR1_RC_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_RRD_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_WTR_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDTIMR2 (		  \
+	(7 << DV_DDR_SDTMR2_RASMAX_SHIFT)	| \
+	(2 << DV_DDR_SDTMR2_XP_SHIFT)		| \
+	(0 << DV_DDR_SDTMR2_ODT_SHIFT)		| \
+	(10 << DV_DDR_SDTMR2_XSNR_SHIFT)	| \
+	(199 << DV_DDR_SDTMR2_XSRD_SHIFT)	| \
+	(1 << DV_DDR_SDTMR2_RTP_SHIFT)		| \
+	(2 << DV_DDR_SDTMR2_CKE_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000492
+#define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
+
 /*
  * Serial Driver info
  */