Merge branch 'master' of git://git.denx.de/u-boot-arm

arch/arm/cpu/arm720t/tegra-common/cpu.c

@@ -378,8 +378,7 @@ void clock_enable_coresight(int enable)
 void halt_avp(void)
 {
 	for (;;) {
-		writel((HALT_COP_EVENT_JTAG | HALT_COP_EVENT_IRQ_1 \
-			| HALT_COP_EVENT_FIQ_1 | (FLOW_MODE_STOP<<29)),
-			FLOW_CTLR_HALT_COP_EVENTS);
+		writel(HALT_COP_EVENT_JTAG | (FLOW_MODE_STOP << 29),
+		       FLOW_CTLR_HALT_COP_EVENTS);
 	}
 }

arch/arm/cpu/arm720t/tegra124/cpu.c

@@ -252,8 +252,8 @@ void start_cpu(u32 reset_vector)
 	tegra124_init_clocks();
 
 	/* Set power-gating timer multiplier */
-	clrbits_le32(&pmc->pmc_pwrgate_timer_mult, TIMER_MULT_MASK);
-	setbits_le32(&pmc->pmc_pwrgate_timer_mult, MULT_8);
+	writel((MULT_8 << TIMER_MULT_SHIFT) | (MULT_8 << TIMER_MULT_CPU_SHIFT),
+	       &pmc->pmc_pwrgate_timer_mult);
 
 	enable_cpu_power_rail();
 	enable_cpu_clocks();

arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c

@@ -143,6 +143,31 @@ void at91_spi1_hw_init(unsigned long cs_mask)
 }
 #endif
 
+#if defined(CONFIG_GENERIC_ATMEL_MCI)
+void at91_mci_hw_init(void)
+{
+	/* Enable mci clock */
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	writel(1 << ATMEL_ID_MCI1, &pmc->pcer);
+
+	at91_set_a_periph(AT91_PIO_PORTA, 6, PUP);	/* MCI1_CK */
+
+#if defined(CONFIG_ATMEL_MCI_PORTB)
+	at91_set_a_periph(AT91_PIO_PORTA, 21, PUP);	/* MCI1_CDB */
+	at91_set_a_periph(AT91_PIO_PORTA, 22, PUP);	/* MCI1_DB0 */
+	at91_set_a_periph(AT91_PIO_PORTA, 23, PUP);	/* MCI1_DB1 */
+	at91_set_a_periph(AT91_PIO_PORTA, 24, PUP);	/* MCI1_DB2 */
+	at91_set_a_periph(AT91_PIO_PORTA, 25, PUP);	/* MCI1_DB3 */
+#else
+	at91_set_a_periph(AT91_PIO_PORTA, 7, PUP);	/* MCI1_CDA */
+	at91_set_a_periph(AT91_PIO_PORTA, 8, PUP);	/* MCI1_DA0 */
+	at91_set_a_periph(AT91_PIO_PORTA, 9, PUP);	/* MCI1_DA1 */
+	at91_set_a_periph(AT91_PIO_PORTA, 10, PUP);	/* MCI1_DA2 */
+	at91_set_a_periph(AT91_PIO_PORTA, 11, PUP);	/* MCI1_DA3 */
+#endif
+}
+#endif
+
 #ifdef CONFIG_MACB
 void at91_macb_hw_init(void)
 {

arch/arm/cpu/armv7/am33xx/clock_am43xx.c

@@ -97,6 +97,7 @@ void enable_basic_clocks(void)
 		&cmper->gpio4clkctrl,
 		&cmper->gpio5clkctrl,
 		&cmper->i2c1clkctrl,
+		&cmper->cpgmac0clkctrl,
 		&cmper->emiffwclkctrl,
 		&cmper->emifclkctrl,
 		&cmper->otfaemifclkctrl,

arch/arm/cpu/armv7/am33xx/ddr.c

@@ -80,8 +80,8 @@ static void configure_mr(int nr, u32 cs)
  */
 void config_sdram_emif4d5(const struct emif_regs *regs, int nr)
 {
-	writel(0x0, &emif_reg[nr]->emif_pwr_mgmt_ctrl);
-	writel(0x0, &emif_reg[nr]->emif_pwr_mgmt_ctrl_shdw);
+	writel(0xA0, &emif_reg[nr]->emif_pwr_mgmt_ctrl);
+	writel(0xA0, &emif_reg[nr]->emif_pwr_mgmt_ctrl_shdw);
 	writel(0x1, &emif_reg[nr]->emif_iodft_tlgc);
 	writel(regs->zq_config, &emif_reg[nr]->emif_zq_config);
 
@@ -96,6 +96,7 @@ void config_sdram_emif4d5(const struct emif_regs *regs, int nr)
 
 	writel(regs->ref_ctrl, &emif_reg[nr]->emif_sdram_ref_ctrl);
 	writel(regs->sdram_config, &emif_reg[nr]->emif_sdram_config);
+	writel(regs->sdram_config, &cstat->secure_emif_sdram_config);
 
 	if (emif_sdram_type() == EMIF_SDRAM_TYPE_LPDDR2) {
 		configure_mr(nr, 0);

arch/arm/cpu/armv7/am33xx/emif4.c

@@ -113,7 +113,7 @@ void config_ddr(unsigned int pll, const struct ctrl_ioregs *ioregs,
 	writel(readl(&cm_device->cm_dll_ctrl) & ~0x1, &cm_device->cm_dll_ctrl);
 	while ((readl(&cm_device->cm_dll_ctrl) && CM_DLL_READYST) == 0)
 		;
-	writel(0x0, &ddrctrl->ddrioctrl);
+	writel(0x80000000, &ddrctrl->ddrioctrl);
 
 	config_io_ctrl(ioregs);
 

arch/arm/cpu/at91-common/spl.c

@@ -52,6 +52,10 @@ u32 spl_boot_device(void)
 {
 #ifdef CONFIG_SYS_USE_MMC
 	return BOOT_DEVICE_MMC1;
+#elif CONFIG_SYS_USE_NANDFLASH
+	return BOOT_DEVICE_NAND;
+#elif CONFIG_SYS_USE_SERIALFLASH
+	return BOOT_DEVICE_SPI;
 #endif
 	return BOOT_DEVICE_NONE;
 }

arch/arm/include/asm/arch-at91/gpio.h

@@ -214,7 +214,7 @@ static inline unsigned pin_to_mask(unsigned pin)
 
 /* The following macros are need for backward compatibility */
 #define at91_set_GPIO_periph(x, y) \
-	at91_set_gpio_periph((x - PIN_BASE) / 32,(x % 32), y)
+	at91_set_pio_periph((x - PIN_BASE) / 32,(x % 32), y)
 #define at91_set_A_periph(x, y) \
 	at91_set_a_periph((x - PIN_BASE) / 32,(x % 32), y)
 #define at91_set_B_periph(x, y) \

arch/arm/include/asm/arch-at91/spl.h

@@ -14,6 +14,10 @@ enum {
 	BOOT_DEVICE_MMC1,
 	BOOT_DEVICE_MMC2,
 	BOOT_DEVICE_MMC2_2,
+#elif CONFIG_SYS_USE_NANDFLASH
+	BOOT_DEVICE_NAND,
+#elif CONFIG_SYS_USE_SERIALFLASH
+	BOOT_DEVICE_SPI,
 #endif
 };
 

arch/arm/include/asm/arch-tegra/pmc.h

@@ -298,14 +298,25 @@ struct pmc_ctlr {
 #define PMC_XOFS_SHIFT	1
 #define PMC_XOFS_MASK	(0x3F << PMC_XOFS_SHIFT)
 
+#if defined(CONFIG_TEGRA114)
 #define TIMER_MULT_SHIFT	0
 #define TIMER_MULT_MASK		(3 << TIMER_MULT_SHIFT)
 #define TIMER_MULT_CPU_SHIFT	2
 #define TIMER_MULT_CPU_MASK	(3 << TIMER_MULT_CPU_SHIFT)
+#elif defined(CONFIG_TEGRA124)
+#define TIMER_MULT_SHIFT	0
+#define TIMER_MULT_MASK		(7 << TIMER_MULT_SHIFT)
+#define TIMER_MULT_CPU_SHIFT	3
+#define TIMER_MULT_CPU_MASK	(7 << TIMER_MULT_CPU_SHIFT)
+#endif
+
 #define MULT_1			0
 #define MULT_2			1
 #define MULT_4			2
 #define MULT_8			3
+#if defined(CONFIG_TEGRA124)
+#define MULT_16			4
+#endif
 
 #define AMAP_WRITE_SHIFT	20
 #define AMAP_WRITE_ON		(1 << AMAP_WRITE_SHIFT)

arch/arm/include/asm/arch-tegra/tegra.h

@@ -34,7 +34,12 @@
 #define NV_PA_PMC_BASE		(NV_PA_APB_MISC_BASE + 0xE400)
 #define NV_PA_EMC_BASE		(NV_PA_APB_MISC_BASE + 0xF400)
 #define NV_PA_FUSE_BASE		(NV_PA_APB_MISC_BASE + 0xF800)
+#if defined(CONFIG_TEGRA20) || defined(CONFIG_TEGRA30) || \
+	defined(CONFIG_TEGRA114)
 #define NV_PA_CSITE_BASE	0x70040000
+#else
+#define NV_PA_CSITE_BASE	0x70800000
+#endif
 #define TEGRA_USB_ADDR_MASK	0xFFFFC000
 
 #define NV_PA_SDRC_CS0		NV_PA_SDRAM_BASE

arch/arm/include/asm/arch-tegra114/tegra.h

@@ -17,6 +17,8 @@
 #ifndef _TEGRA114_H_
 #define _TEGRA114_H_
 
+#define CONFIG_TEGRA114
+
 #define NV_PA_SDRAM_BASE	0x80000000	/* 0x80000000 for real T114 */
 #define NV_PA_TSC_BASE		0x700F0000	/* System Counter TSC regs */
 

arch/arm/include/asm/arch-tegra124/tegra.h

@@ -8,6 +8,8 @@
 #ifndef _TEGRA124_H_
 #define _TEGRA124_H_
 
+#define CONFIG_TEGRA124
+
 #define NV_PA_SDRAM_BASE	0x80000000
 #define NV_PA_TSC_BASE		0x700F0000	/* System Counter TSC regs */
 #define NV_PA_MC_BASE		0x70019000	/* Mem Ctlr regs (MCB, etc.) */

arch/arm/include/asm/arch-tegra20/tegra.h

@@ -8,6 +8,8 @@
 #ifndef _TEGRA20_H_
 #define _TEGRA20_H_
 
+#define CONFIG_TEGRA20
+
 #define NV_PA_SDRAM_BASE	0x00000000
 
 #include <asm/arch-tegra/tegra.h>

arch/arm/include/asm/arch-tegra30/tegra.h

@@ -17,6 +17,8 @@
 #ifndef _TEGRA30_H_
 #define _TEGRA30_H_
 
+#define CONFIG_TEGRA30
+
 #define NV_PA_SDRAM_BASE	0x80000000	/* 0x80000000 for real T30 */
 
 #include <asm/arch-tegra/tegra.h>

board/BuR/common/common.c

@@ -141,12 +141,12 @@ static struct cpsw_slave_data cpsw_slaves[] = {
 	{
 		.slave_reg_ofs	= 0x208,
 		.sliver_reg_ofs	= 0xd80,
-		.phy_id		= 0,
+		.phy_addr	= 1,
 	},
 	{
 		.slave_reg_ofs	= 0x308,
 		.sliver_reg_ofs	= 0xdc0,
-		.phy_id		= 1,
+		.phy_addr	= 2,
 	},
 };
 

board/atmel/at91sam9263ek/at91sam9263ek.c

@@ -24,6 +24,7 @@
 #include <net.h>
 #endif
 #include <netdev.h>
+#include <atmel_mci.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -214,6 +215,15 @@ void lcd_show_board_info(void)
 #endif /* CONFIG_LCD_INFO */
 #endif
 
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+int board_mmc_init(bd_t *bd)
+{
+	at91_mci_hw_init();
+
+	return atmel_mci_init((void *)ATMEL_BASE_MCI1);
+}
+#endif
+
 int board_early_init_f(void)
 {
 	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;

board/atmel/sama5d3_xplained/Makefile

+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2008
+# Stelian Pop <stelian@popies.net>
+# Lead Tech Design <www.leadtechdesign.com>
+#
+# (C) Copyright 2014
+# Bo Shen <voice.shen@atmel.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += sama5d3_xplained.o

board/atmel/sama5d3_xplained/sama5d3_xplained.c

+/*
+ * Copyright (C) 2014 Atmel Corporation
+ *		      Bo Shen <voice.shen@atmel.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mmc.h>
+#include <asm/io.h>
+#include <asm/arch/sama5d3_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <atmel_mci.h>
+#include <net.h>
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_NAND_ATMEL
+void sama5d3_xplained_nand_hw_init(void)
+{
+	struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+
+	at91_periph_clk_enable(ATMEL_ID_SMC);
+
+	/* Configure SMC CS3 for NAND/SmartMedia */
+	writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(1) |
+	       AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(1),
+	       &smc->cs[3].setup);
+	writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
+	       AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(5),
+	       &smc->cs[3].pulse);
+	writel(AT91_SMC_CYCLE_NWE(8) | AT91_SMC_CYCLE_NRD(8),
+	       &smc->cs[3].cycle);
+	writel(AT91_SMC_TIMINGS_TCLR(3) | AT91_SMC_TIMINGS_TADL(10) |
+	       AT91_SMC_TIMINGS_TAR(3)  | AT91_SMC_TIMINGS_TRR(4)   |
+	       AT91_SMC_TIMINGS_TWB(5)  | AT91_SMC_TIMINGS_RBNSEL(3)|
+	       AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
+	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+	       AT91_SMC_MODE_EXNW_DISABLE |
+#ifdef CONFIG_SYS_NAND_DBW_16
+	       AT91_SMC_MODE_DBW_16 |
+#else /* CONFIG_SYS_NAND_DBW_8 */
+	       AT91_SMC_MODE_DBW_8 |
+#endif
+	       AT91_SMC_MODE_TDF_CYCLE(3),
+	       &smc->cs[3].mode);
+}
+#endif
+
+#ifdef CONFIG_CMD_USB
+static void sama5d3_xplained_usb_hw_init(void)
+{
+	at91_set_pio_output(AT91_PIO_PORTE, 3, 0);
+	at91_set_pio_output(AT91_PIO_PORTE, 4, 0);
+}
+#endif
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+static void sama5d3_xplained_mci0_hw_init(void)
+{
+	at91_mci_hw_init();
+
+	at91_set_pio_output(AT91_PIO_PORTE, 2, 0);	/* MCI0 Power */
+}
+#endif
+
+int board_early_init_f(void)
+{
+	at91_periph_clk_enable(ATMEL_ID_PIOA);
+	at91_periph_clk_enable(ATMEL_ID_PIOB);
+	at91_periph_clk_enable(ATMEL_ID_PIOC);
+	at91_periph_clk_enable(ATMEL_ID_PIOD);
+	at91_periph_clk_enable(ATMEL_ID_PIOE);
+
+	at91_seriald_hw_init();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_NAND_ATMEL
+	sama5d3_xplained_nand_hw_init();
+#endif
+#ifdef CONFIG_CMD_USB
+	sama5d3_xplained_usb_hw_init();
+#endif
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+	sama5d3_xplained_mci0_hw_init();
+#endif
+#ifdef CONFIG_MACB
+	at91_gmac_hw_init();
+	at91_macb_hw_init();
+#endif
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+				    CONFIG_SYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_MACB
+	macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
+	macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+int board_mmc_init(bd_t *bis)
+{
+	atmel_mci_init((void *)ATMEL_BASE_MCI0);
+
+	return 0;
+}
+#endif

board/atmel/sama5d3xek/sama5d3xek.c

@@ -307,6 +307,10 @@ void spl_board_init(void)
 {
 #ifdef CONFIG_SYS_USE_MMC
 	sama5d3xek_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+	sama5d3xek_nand_hw_init();
+#elif CONFIG_SYS_USE_SERIALFLASH
+	at91_spi0_hw_init(1 << 0);
 #endif
 }