This avoids cache-alignment warnings shown in console
when a usb command is entered.

Whenever X bytes of unaligned buffer is invalidated, arm core
invalidates X + Y bytes as per the cache line size and throws
these warnings.

Signed-off-by: Puneet Saxena <puneets@nvidia.com>
Signed-off-by: Marek Vasut <marex@denx.de>

Building usb for Blackfin boards fails as we get linux/compiler.h
included which expands the "noinline" inside of the attribute and
we get attribute(attribute(noinline)).

Explicitly use the helper define to avoid this.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The patch that added parallel builds broke MAKEALL -l, so this
fixes that. At the same time, it improves the termination so
that it shuts down the build threads if you cancel the build.
Lastly, it removes a bunch of debug code.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Wolfgang Denk <wd@denx.de>

pdnb3 and scpu are explicitly on LIST_ixp, even though they are
also specified in boards.cfg as having cpu ixp. This means that
they will be built twice when doing ./MAKEALL ixp, or ./MAKEALL arm.

This was pointless before, but actually breaks things if you launch
both builds at the same time, as they overwrite each other.

Signed-off-by: Andy Fleming <afleming@freescale.com>

* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
  lin_gadget: use common linux/compat.h
  linux/compat.h: rename from linux/mtd/compat.h
  lin_gadget: use common mdelay
  gunzip: rename z{alloc, free} to gz{alloc, free}
  fs/fat: align disk buffers on cache line to enable DMA and cache
  part_dos: align disk buffers on cache line to enable DMA and cache

* 'master' of /home/wd/git/u-boot/custodians:
  powerpc/ppc4xx: Remove typedefs for gdsys FPGA
  powerpc/ppc4xx: Fix typo in gdsys_fpga.h
  powerpc/ppc4xx: Update gdsys board configurations
  powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
  powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
  powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
  powerpc/ppc4xx: Adjust environment size on neo

* 'master' of git://git.denx.de/u-boot-ppc4xx:
  powerpc/ppc4xx: Remove typedefs for gdsys FPGA
  powerpc/ppc4xx: Fix typo in gdsys_fpga.h
  powerpc/ppc4xx: Update gdsys board configurations
  powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
  powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
  powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
  powerpc/ppc4xx: Adjust environment size on neo

Merge our duplicate definitions with the common header.

Also fix drivers/usb/gadget/s3c_udc_otg_xfer_dma.c to
use min() instead of min_t() since we remove the latter
from compat.h.

Additionally use memalign() directly as the lin_gadget
specific kmalloc() macro is removed from lin_gadget_compat.h
by this patch.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>

This lets us use it in more places than just mtd code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No need to provide our own mdelay() macro when we have a func for it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This allows us to add a proper zalloc() func (one that does a zeroing
alloc), and removes duplicate prototypes.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

The MAKEALL script cleverly runs make with the appropriate options
to use all of the cores on the system, but your average U-Boot build
can't make much use of more than a few cores.  If you happen to have
a many-core server, your builds will leave most of the system idle.

In order to make full use of such a system, we need to build multiple
targets in parallel, and this requires directing make output into
multiple directories. We add a BUILD_NBUILDS variable, which allows
users to specify how many builds to run in parallel.
When BUILD_NBUILDS is set greater than 1, we redefine BUILD_DIR for
each build to be ${BUILD_DIR}/${target}. Also, we make "./build" the
default BUILD_DIR when BUILD_NBUILDS is greater than 1.

MAKEALL now tracks which builds are still running, and when one
finishes, it starts a new build.

Once each build finishes, we run "make tidy" on its directory, to reduce
the footprint.

As a result, we are left with a build directory with all of the built
targets still there for use, which means anyone who wanted to use
MAKEALL as part of a test harness can now do so.

Signed-off-by: Andy Fleming <afleming@freescale.com>

* 'master' of /home/wd/git/u-boot/custodians:
  powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
  powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
  cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
  PowerPC: correct the SATA for p1/p2 rdb-pc platform
  powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
  powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
  powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
  powerpc/corenet_ds: Slave module for boot from SRIO
  powerpc/corenet_ds: Master module for boot from SRIO
  powerpc/corenet_ds: Document for the boot from SRIO
  powerpc/corenet_ds: Correct the compilation errors about ENV
  powerpc/srio: Rewrite the struct ccsr_rio
  powerpc/85xx:Fix lds for nand boot debug info
  powerpc/p2041rdb: add env in NAND support
  powerpc/p2041rdb: add NAND and NAND boot support
  powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
  powerpc/85xx:Avoid vector table compilation for nand_spl
  powerpc/85xx:Fix IVORs addr after vector table relocation
  powerpc/85xx:Avoid hardcoded vector address for IVORs
  powerpc/p1023rds: Disable nor flash node and enable nand flash node

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
  powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
  cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
  PowerPC: correct the SATA for p1/p2 rdb-pc platform
  powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
  powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
  powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
  powerpc/corenet_ds: Slave module for boot from SRIO
  powerpc/corenet_ds: Master module for boot from SRIO
  powerpc/corenet_ds: Document for the boot from SRIO
  powerpc/corenet_ds: Correct the compilation errors about ENV
  powerpc/srio: Rewrite the struct ccsr_rio
  powerpc/85xx:Fix lds for nand boot debug info
  powerpc/p2041rdb: add env in NAND support
  powerpc/p2041rdb: add NAND and NAND boot support
  powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
  powerpc/85xx:Avoid vector table compilation for nand_spl
  powerpc/85xx:Fix IVORs addr after vector table relocation
  powerpc/85xx:Avoid hardcoded vector address for IVORs
  powerpc/p1023rds: Disable nor flash node and enable nand flash node

* 'master' of /home/wd/git/u-boot/custodians:
  i2c:designware Turn off the ctrl when setting the speed
  i2c: Add support for designware i2c controller
  sh: i2c: Add support I2C controller of SH7734

* 'master' of git://git.denx.de/u-boot-i2c:
  i2c:designware Turn off the ctrl when setting the speed
  i2c: Add support for designware i2c controller
  sh: i2c: Add support I2C controller of SH7734

* 'master' of /home/wd/git/u-boot/custodians:
  Blackfin: bfin_sdh: drop dos part hardcode
  Blackfin: move gd/bd to bss by default
  Blackfin: gd_t: relocate volatile markings

* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: bfin_sdh: drop dos part hardcode
  Blackfin: move gd/bd to bss by default
  Blackfin: gd_t: relocate volatile markings

Putting "inline" on extern funcs makes no sense, so drop them.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

* 'master' of git://git.denx.de/u-boot-nds32:
  board/adp-ag102: add configuration of adp-ag102
  board/adp-ag102: add board specific files
  nds32/ag102: add ag102 soc support
  nds32/ag102: add header support of ag102 soc

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

In hardware revision 1.20 one more fan controller is added to dlvision-10g.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Print fpga info at last_stage_init on gdsys 405ep boards.
Use dtt_init() to startup fans.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

In order to add boards that have different hardware for fpga reset,
any 405ep gdsys board now provides these functions:

void gd405ep_init(void);
void gd405ep_set_fpga_reset(unsigned state);
void gd405ep_setup_hw(void);
int gd405ep_get_fpga_done(unsigned fpga);

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Environment size on neo has to be 0x20000 for compatibilty reasons.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Fix the location of patman path in README

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: Simon Glass <sjg@chromium.org>

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

md5.c: In function ‘MD5Final’:
md5.c:156:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
md5.c:157:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

cmd_nand.c: In function ‘arg_off_size’:
cmd_nand.c:216:5: warning: ‘maxsize’ may be used uninitialized in this function [-Wmaybe-uninitialized]

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>

* 'marex@denx.de' of git://git.denx.de/u-boot-staging:
  CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
  CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE
  CMD: Fix typo CMD_FSL -> CMD_MFSL in readme
  HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
  CMD: Remove CMD_LOG, it's unused
  CMD: Fix typo KGBD -> KGDB on debris board
  CMD: Drop CONFIG_CMD_EMMC, it's not used
  CMD: Drop CONFIG_CMD_DFL, it's not used
  CMD: Drop CMD_DCR, it's not used
  CMD: Drop CMD_CAN, it's not used
  CMD: Remove CMD_AUTOSCRIPT, it's not used
  AT91: Drop AT91_SPIMUX command from cmd_all

Signed-off-by: Wolfgang Denk <wd@denx.de>

The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but
that register does not exist on e500v1.

Signed-off-by: Timur Tabi <timur@freescale.com>

Most 85xx boards can be built as a 32-bit or a 36-bit.  Current code sometimes
displays which of these is actually built, but it's inconsistent.  This is
especially problematic since the "default" build for a given 85xx board can
be either one, so if you don't see a message, you can't always know which
size is being used.  Not only that, but each board includes code that displays
the message, so there is duplication.

The 'bdinfo' command has been updated to display this information, so
we don't need to display it at boot time.  The board-specific code is
deleted.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

Some Freescale SOCs support 32-bit and 36-bit physical addressing, and
U-Boot must be built to enable one or the other.  Add this information
to the bdinfo command.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

For p1/p2 rdb-pc platform, use the PCIe-SATA Silicon Image SATA controller.
Therefore, the SATA driver will use sata_sil, instead sata_sil3114.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>

When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.

Master needs to:
	1. Set outbound SRIO windows in order to configure slave's registers
	   for the core's releasing.
	2. Check the SRIO port status when release slave core, if no errors,
	   will implement the process of the slave core's releasing.
Slave needs to:
	1. Set all the cores in holdoff by RCW.
	2. Be powered on before master's boot.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>