After we authenticate/decrypt an image we need to flush the caches
as they may still contain bits of the encrypted image. This will
cause failures if we attempt to jump to this image.

Reported-by: Yogesh <Siraswar&lt;yogeshs@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Re-use of routines embedded in the Boot ROM requires a function
pointer table for each SoC.  This is not nice in terms of the
maintainability in a long run.

Implement simple eMMC load APIs that are commonly used for LD11,
LD20, and hopefully future SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

For LD11 and LD20 SoCs, the RST_n pin is asserted by default.  If
the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device
would stay in the reset state until its RST_n pin is deasserted by
software.

Currently, this is cared by an ad-hoc way because the eMMC hardware
reset provider is not supported in U-Boot for now.  This code should
be re-written once the "mmc-pwrseq-emmc" binding is supported.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

If the DRAM clock duty does not meet the allowable tolerance,
it is marked in an efuse register.  If the register is fused,
the boot code should compensate for the DRAM clock duty error.

Signed-off-by: Kotaro Hayashi <hayashi.kotaro@socionext.com>
[masahiro: simplify code, add git-log]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This parameter is redundant because we can know the number of
channels by checking if dram_ch[2].size is zero.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The current implementation has ugly switch statements here and there,
and duplicates similar code.  Rework it using table lookups for SoC
data and reduce code duplication.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The spl_boot_mode() is unrelated to the other code in this file.
Besides, this function is only called from common/spl/spl_mmc.c,
so it is reasonable to guard with CONFIG_SPL_MMC_SUPPORT.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Currently, arch/arm/mach-uniphier/boot-mode/boot-mode.c is messed up
with unrelated code; there is no reason why the "mmcsetn" command
must be placed in this file.

Split out the MMC code into arch/arm/mach-uniphier/mmc-first-dev.c.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since commit 26b09c02 ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), SPL does not need pin-mux settings for
the System Bus.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

The base address of each DRAM channel can be calculated from other
parameters, so does not need hard-coding.  What we need is the size
of each DRAM channel and DRAM_SPARSE flag to decide the start address
of DRAM channel 1.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since commit 26b09c02 ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), the System Bus is initialized by
board_init().  The show_board_info() is called from board_init_f()
by default, so the revision register of the Micro Support Card may
not be accessed at this point.  Show its revision after the System
Bus is initialized.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Now the "for" loop here iterates on the detected memory banks.
It must skip unused DRAM banks.

Fixes: c995f3a3 ("ARM: uniphier: use gd->bd->bi_dram for memory reserve on LD20 SoC")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

If SG_MEMCONF_CH2_DISABLE bit is set, the DRAM channel 2 is unused.
The register settings for the ch2 should be ignored.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit a8e6300d ("ARM: uniphier: refactor spl_init_board()")
accidentally dropped dcache_disable() call.  Since then, the SPL of
LD11 and LD20 failed to load U-Boot proper.

Fixes: a8e6300d ("ARM: uniphier: refactor spl_init_board()")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

There is no microcode update available for SoCs used on Intel MID
platforms.

Use conditional to bypass it.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Intel MID platform boards have special treatment, such as boot parameter
setting.

Assign hardware_subarch accordingly if CONFIG_INTEL_MID is set.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Intel Mobile Internet Device (MID) platforms have special treatment in
some cases, such as CPU enumeration or boot parameters configuration.

Besides that several drivers are specifically developed for the IP
blocks found on Intel MID platforms. Those drivers will be dependent to
this option.

Here we introduce specific quirk option for such cases.

It is supposed to be selected by Intel MID platform boards, for example,
Intel Edison.

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Depending upon the compiler used, IRQ entries could vary in sizes. With
GCC 5.x, the code generator will use short jumps for some IRQ entries
but near jumps for others. For example, GCC 5.4.0 generates the
following:

$ objdump -d interrupt.o
<snip>
00000207 <irq_18>:
207:   6a 12                   push   $0x12
209:   eb 85                   jmp    190 <irq_common_entry>

0000020b <irq_19>:
20b:   6a 13                   push   $0x13
20d:   eb 81                   jmp    190 <irq_common_entry>

0000020f <irq_20>:
20f:   6a 14                   push   $0x14
211:   e9 7a ff ff ff          jmp    190 <irq_common_entry>

00000216 <irq_21>:
216:   6a 15                   push   $0x15
218:   e9 73 ff ff ff          jmp    190 <irq_common_entry>

This causes a problem in cpu_init_interrupts(), because the IDT setup
assumed same sizes for all IRQ entries. GCC 4.x always generated 32-bit
jumps, so this previously was not a problem.

The fix is to force 32-bit near jumps for all entries within the
inline assembly. This works for GCC 5.x, and 4.x was already using
that form of jumping.

Signed-off-by: Jason Tang <tang@jtang.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

When using early malloc the allocated memory can overflow into the SRAM
scratch space, move NON_SECURE_SRAM_IMG_END down a bit to allow more
dynamic allocation at the expense of a slightly smaller maximum image
size.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig.

Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to
Kconfig the board defconfigs for db-88f6820-gp_defconfig
kc1_defconfig and sniper_defconfig need to be updated.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>

the socfpga bootrom supports mmc booting from either a raw image
starting at 0x0, or from a partition of type 0xa2.  This patch
adds support for locating the boot image in the first type 0xa2
partition found.

Assigned a partition number of -1 will cause a search for a
partition of type CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
and use it to find the u-boot image

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>

When the node 'reserved-memory' is not defined in the DT we fail
to add needed properties. We also fail to move 'offs' to point to
the new node. Fix these here.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Use correct name in endif comment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.

Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

miniarm board use lpddr3

Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added 'rockchip:' prefix to subject:
Signed-off-by: Simon Glass <sjg@chromium.org>

Change-Id: I84c3679dab2dbd8d01c1ebfd22220946d07c03cd

To use driver-model adds the pmic node for max8997.
This is used as kernel device-tree in Linux.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

CONFIG_CMD_ZIP is not defined by any board.  I am moving
CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family.

I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP"
is better for this platform.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>

There are two typos in the comment "invalide i-cache is enabled".
We can fix it by
  invalide -> invalidate
  is       -> if

Or, if we want to match the comment to the code, we can say
"skip invalidating i-cache if disabled".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.

Script for the same (and hand modified for Makefile and config
files):
for i in arch/arm/dts/k2*
do
	b=`basename $i`;
	git mv $i arch/arm/dts/keystone-$b;
	sed -i -e "s/$b/keystone-$b/g" arch/arm/dts/*[si]
done

This is similar to linux kernel commit 5edafc29829bc ("ARM: dts: k2*: Rename
the k2* files to keystone-k2* files")

[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2



Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Save one instruction.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

AArch64 has a zero register (xzr).  Use it instead of x2.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>

If there is a '.' in a compatible string, then dtoc will produce a struct
with a name containing a '.'. This won't work, so replace it with '_'.

Also add a suitable test to the sandbox device tree to catch this.

Signed-off-by: Simon Glass <sjg@chromium.org>

The mpuclk register in the Altera group of the clock manager
divides the mpu_clk that is generated from the C0 output of the main
pll.

Without this patch, the default value of the register is 1, so the mpuclk
will always get divided by 2 if the correct value is not set. For example,
on the Arria5 socdk board, the MPU clock is only 525 MHz, and it should be
1.05 GHz.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Add support for programmable MAC impedance configuration and
fix typo in DT impedance parameters names.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This option is useful not only for development, but for the platforms
where U-Boot is run from custom ROM bootloader. For example, Intel
Edison is that board.

Make this option visible that platforms can select it if needed.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

QEMU does not need ucode and this is indicated in u-boot.dtsi
for U-Boot proper. Now add the same for SPL.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>