Since PLL2 now has changed, it is necessary to adapt the CONFIG_IPUV3_CLK
accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz.

Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz
instead.

Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI
at 1080p because the IPU clock cannot reach the requested frequency.

Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its
maximum frequency.

Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little
bit to allow easier comparison with the original clock setup from FSL U-boot.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

init_clock is currently shared between mx51 and mx53 and it contains lots of
ifdef's which makes it really hard to follow the code.

Split the init_clock between mx51 and mx53 to allow easier readability.

No functional changes are made.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Clean up i.MX25 imx-regs.h:
 - Update mx31 imx-regs.h filename.
 - Test for __KERNEL_STRICT_NAMES just in case.
 - Define internal RAM size.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

Adds support for HDMI, two LVDS panels and one RGB panel to
the SABRE-Lite board.

Displays supported:
         HDMI		- 1024 x 768 for maximum compatibility
         Hannstar-XGA   - 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1)
         wsvga-lvds     - 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600)
         wvga-rgb       - 800 x 480 RGB (Boundary p/n Nit6X_800x480)

Since the ipuv3_fb display driver currently supports only a single display,
this code auto-detects panel by probing the HDMI Phy for Hot Plug Detect
or the I2C touch controller of the LVDS and RGB displays in the priority
listed above.

Setting 'panel' environment variable to one of the names above will
override auto-detection.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Original source from Pengutronix HDMI driver work:

	http://git.pengutronix.de/?p=imx/linux-2.6.git;a=commitdiff;h=72c31cd67ac880bd90785af86f8e46f8ea7b3bb0



Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Default drive strength is disabled and won't function.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>

The kernel from Freescale expects that the bootloader passes the board revision.

Read the board revision and pass it via get_board_rev().

Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

The mmcroot setting vary between mx6qsabreauto and mx6qsabresd so we
move this to the board configuration file.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>

On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).

This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>

Each eSDHC instance has a dedicated clock.

gd->sdhc_clk must also be set accordingly. This is good for the case only a
single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A
future patch will fix the multi-instance use case (initialization made directly
with fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>

Clean up mx35 lowlevel_init:
 - Indent with tabs.
 - Fix comments.
 - Use defined values instead of literal constants.
 - Use defined macros instead of duplicating code.
 - Use macro parameters with default values instead of #define'd configs.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

This was introduced in:
8679d0ffdcc0beafea8e6942c0c67cf859afa18e -
	COMMON: Use __stringify() instead of MK_STR()

The header is now needed since common.h is not included in this tool.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

Add entry for kerneldoc into the git-mailrc pointing to the U-Boot ML
and myself.

Signed-off-by: Marek Vasut <marex@denx.de>

The default kernel-doc strips starting spaces from every single
line in the Example section. This makes the code look bad. Thus,
implement special handling for this section.

Signed-off-by: Marek Vasut <marex@denx.de>

Import basic CSS stylesheet for the HTML documentation. The base for
the stylesheet is taken from:

	http://ds9a.nl/docbook/minimal-page.html



I customized the CSS a bit further, for example to add curvy corners
to example section and change the tint of gray. The HTML documentation
does not look that crude anymore.

Signed-off-by: Marek Vasut <marex@denx.de>

Pull slightly modified version of Documentation/DocBook, the related perl
script scripts/kernel-doc and the scripts/docproc.c from Linux kernel and
implant it into U-Boot. This will allow smooth generation of kerneldoc
style documentation.

It was necessary to modify the DocBook/Makefile to work with U-Boot build
system. The changes were only minor though and involved replacing the kbuild
specific parts.

It was also necessary to replace use of variables like KERNEL_VERSION with
U_BOOT_VERSION, strings like Linux kernel with U-Boot Bootloader etc. so
the generated result actually matches.

Finally, it was necessary to adjust docproc.c, since the documentation in
U-Boot is located in doc/DocBook instead of Documentation/DocBook as is in
case of the Linux kernel.

Some parts of the DocBook Makefile are unused, but to allow easier sync with
Linux kernel, these parts are still left in. The targets enabled now are
"htmldocs" "pdfdocs" "psdocs" "xmldocs" and "cleandocs" to remove the results
of documentation build.

Linux scripts/docproc.c:
commit f0f3ca8d967462dafb815412b14ca3339b9817a6
Date:   Wed Jun 15 11:53:13 2011 +0200

Linux scripts/kernel-doc:
commit 1b40c1944db445c1de1c47ffd8cd426167f488e8
Date:   Sun Aug 12 10:46:15 2012 +0200

Linux Documentation/DocBook:
commit bb8187d35f820671d6dd76700d77a6b55f95e2c5
Date:   Thu May 17 19:06:13 2012 -0400

Signed-off-by: Marek Vasut <marex@denx.de>

Since commit 50d4a707f0 (mx5/6: Define default SoC input clock frequencies)
we can use the default clock values.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

mx6qsabreauto has a AR8031 Gigabit PHY.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Clean up mx25 lowlevel_init:
 - Add comments.
 - Do not use write32 repeatedly with the same value in order not to increase
   code size.
 - Make register values configurable.
 - Use macro parameters with default values instead of literal constants.
 - Use defined macros instead of duplicating code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Matthias Weisser <weisserm@arcor.de>

The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

Optimize mx5 lowlevel_init.S code size:
 - Compute values at compile time rather than at runtime where possible.
 - Assign r4 to hold the zero value rather than setting registers to 0 again and
   again.
 - Associate a function to setup_pll rather than expanding its large macro code
   multiple times.
 - Allocate constant values in section only if used.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

The mx6qsabreauto console is different than mx6qsabresd so the console
configuration is now set in the board file.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>

The MMC driver appropriate for the i.MX25 is fsl_esdhc, which has nothing to do
with mxcmmc.

Also, each eSDHC instance has a dedicated clock, so gd->sdhc_clk must be set
accordingly. This is good for the case only a single SDHC instance is used
(initialization made with fsl_esdhc_mmc_init()). A future patch will fix the
multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>

The FEC is the only SoC Ethernet support available on i.MX25, so define
cpu_eth_init() only for it instead of returning a misleading success code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

Use the standard mxc_get_clock() instead of exporting internal functions and
using literal constant values.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock.

Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG
clock, so remove the duplicated code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

Define AHB, IPG and CSPI clocks.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

Avoid possible overflow in clock calculations, and do not waste calls to lldiv()
to divide simple ulongs.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

The i.MX5 eSDHC clocks were considered as coming from the IPG clock although
they have dedicated clock paths.

Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must
be set accordingly. This is good for the case only a single SDHC instance is
used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix
the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>

There are only 2 I²C instances on i.MX51, but 3 on i.MX53.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

The FEC clock does not come from PLL1, but from the IPG clock. The previous code
was even inconsistent with itself, returning the IPG clock as expected for
imx_get_fecclk(), but the PLL1 clock for mxc_get_clock(MXC_FEC_CLK).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>