Signed-off-by: Wolfgang Denk <wd@denx.de>

The following MPC5121e subsystems are supported:

- low-level CPU init
- NOR Boot Flash (common CFI driver)
- DDR SDRAM
- FEC
- I2C
- Watchdog

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Jan Wrobel <wrr@semihalf.com>

Signed-off-by: Rafal Jaworowski <raj@semihalf.com>

This patch fixes the negative consequences for 8xx of the recent
"ppc4xx: Clean up 440 exceptions handling" commit.

Signed-off-by: Rafal Jaworowski <raj@semihalf.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

		- fix compile error, if BUILD_DIR is used

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>

            - now the Flash ST M29W040B is supported (not tested)
            - fix the "led" command
            - fix compile error, if BUILD_DIR is used

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>

- Add optional ECC generation routine to preserve existing
  RAM values. This is needed for the Linux log-buffer support
- Add optional DDR2 setup with CL=4
- GPIO50 not used anymore
- Lime register setup added

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: mushtaq khan <mushtaqk_921@yahoo.co.in>

Signed-off-by: Heiko Schocher <hs@denx.de>

This patch prints the DDR status registers upon machine check
interrupt on the 440EPx/GRx. This can be useful especially when
ECC support is enabled.

I added some small changes to the original patch from Niklaus to
make it compile clean.

Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>
Signed-off-by: Stefan Roese <sr@denx.de>

This patch fixes the problem to assemble cpu/ppc4xx/start.S
experienced last week where building failed having specified
O=../build.sequoia.

Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>

This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.

Signed-off-by: Stefan Roese <sr@denx.de>

-add pci_pre_init() for pci interrupt fixup code
-disable phy sleep mode via reset_phy() function
-use correct io accessors
-cleanup

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch adds support for calling a plattform dependant
pci_pre_init() function for 405 boards. This can be used to
move the current pci_405gp_fixup_irq() function into the
board code.

This patch also makes the CFG_PCI_PRE_INIT define obsolete.
A default function with 'weak' attribute is used when
a board specific pci_pre_init() is not implemented.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

A new environment variable, "logversion", selects the log buffer
behaviour. If it is not set or set to a value other than 2, then the
old, Linux 2.4.4, behaviour is selected.

Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--

Added memory, CPU, UART, I2C and SPR POST tests for PPC440.

Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--

                - Show on the Status LEDs, some States of the board.
                - Get the MAC addresses from the EEProm
                - use PREBOOT
                - use the CF on the board.
                - check the U-Boot image in the Flash with a SHA1
                  checksum.
                - use dynamic TLB entries generation for the SDRAM

Signed-off-by: Heiko Schocher <hs@denx.de>

The recently extended program_tlb() function had a problem when
multiple TLB's had to be setup (for example with 512MB of SDRAM). The
virtual address was not incremented. This patch fixes this issue
and is tested on Katmai with 512MB SDRAM.

Signed-off-by: Stefan Roese <sr@denx.de>

- adapt to the more generic EXCEPTION_PROLOG and CRIT_EXCEPTION macros
- minor 4xx cleanup

This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:

=> bootstrap 533 nor        ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand       ;to configure the board for 667MHz NNAND booting

Signed-off-by: Stefan Roese <sr@denx.de>

The latest changes showed a problem with the location of the NAND-SPL
image in the OCM and the init-data area (incl. cache). This patch
fixes this problem.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>