Add code for configuring IDT8T49N222A device for various output refclks
    - The IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer with
      alarm and monitoring functions suitable for networking and
      communications applications. It is able to generate wide range of output
      frequencies.
    - In B4860QDS, it has been used to generate different refclks to SerDes modules
    - Programming of these devices are performed by I2C interface.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side
DDR. They are mapped to PowerPC and DSP CCSR space respectively.
BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC
and other to DSP side controller.

Configure DSP DDR controller similar to PowerPC side DDR controller as
memories are exactly similar.

Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a
integrated device that contains two powerpc e500v2 cores and two DSP
starcores.

To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 and M3 memory
-Creating LAW for 1GB DDR which is connected exclusively to DSP-cores

Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

When a board (slave) boots from SRIO/PCIE, it would get the instructions
from a remote board (master) by SRIO/PCIE interface, and the slave's
u-boot image should be built with the

	SYS_TEXT_BASE=0xFFF80000;

So the u-boot of the slave should avoid the NOR_BOOT branch at the
booting stage.

For example, when a P2041RDB boots from SRIO/PCIE, it will set TLB
entry 15 from base address "CONFIG_SYS_MONITOR_BASE & 0xffc00000",
and with the 4M size as the boot window in NOR_BOOT branch. Because
the CONFIG_SYS_MONITOR_BASE = CONFIG_SYS_TEXT_BASE = 0xFFF80000, so
the TLB entry will be from base address 0xffc00000 and with 4M size.

Then the u-boot will set TLB entry 14 from base address
"CONFIG_SYS_INIT_RAM_ADDR", and with the 16K size as the initial
stack window. For the P2041RDB platform, the CONFIG_SYS_INIT_RAM_ADDR
= 0xffd00000. So the TLB entry 14 and 15 will be in confliction.

There will be right TLB entries configurations when avoid the
NOR_BOOT branch and set the boot window from 0xfff00000 with 1M
size space.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>

Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB.
DDR changed from DDR2 1G to DDR3 2G.
NAND: 128 MiB
Flash: 64 MiB

Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.

Signed-off-by: York Sun <yorksun@freescale.com>

JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.

Signed-off-by: York Sun <yorksun@freescale.com>

On selected platforms, x4 DDR devices can be supported. Using x4 devices may
lower the performance, but generally they are available for higher density.

Tested on MT36JSF2G72PZ-1G9E1 RDIMM.

Signed-off-by: York Sun <yorksun@freescale.com>

RDIMM has different timing. Tested RDIMM is MT18JSF1G72PDZ-1G9E1 for
dual rank. Single- and quad-rank are not tested due to availability.

Signed-off-by: York Sun <yorksun@freescale.com>

When chip select interleaving is enabled, cs0_bnds is used for address
binding. Other csn_bnds are not used. When two controllers interleaving is
enabled, cs0_bnds of both controllers are used, other csn_bnds are not.
However, the unused csn_bnds may be used internally for calculating
addresses for calibration. Setting those registers to 0 may confuse
controllers in some cases. Instead, setting them to 0xffffffff together
with normal LAWs will guarantee the address is not mapped to DDR.

Signed-off-by: York Sun <yorksun@freescale.com>

Add emulator support for T4240. Emulator has limited peripherals and
interfaces. Difference between emulator and T4240QDS includes:
	ECC for DDR is disabled due the procedure to load images
	No board FPGA (QIXIS)
	NOR flash has 32-bit port for higher loading speed
	IFC and I2C timing don't really matter, so set them fast
	No ethernet

Signed-off-by: York Sun <yorksun@freescale.com>

The RCW print is common for all corenet platforms. Not necessary to ducplicate
in each board file.

Signed-off-by: York Sun <yorksun@freescale.com>

CONFIG_PHYS_64BIT is always defined for t4qds. Removed unused #ifdef.

Signed-off-by: York Sun <yorksun@freescale.com>

Prepare for emulator support for mpc85xx parts.
Disable DDR training and skip wrlvl_cntl_2 and wrlvl_cntl_3 registers.
These two registers improve stability but not supported by emulator.
Add CONFIG_FSL_TBCLK_EXTRA_DIV for possible adjustment to time base.

Signed-off-by: York Sun <yorksun@freescale.com>

FMAN firmware can be in NOR flash, NAND flash, SPI flash, MMC or even
remote. In case none of them is defined, set it to null.

Signed-off-by: York Sun <yorksun@freescale.com>

Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.

Signed-off-by: York Sun <yorksun@freescale.com>

For T4 platform, the SRIO LIODN registers are in SRIO address space
and not in GUTs.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>

For B4, the SRIO LIODN registers are in SRIO address space and not
in GUTs.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>

For some PowerPC platforms, LIODN registers for SRIO ports are
in SRIO register address space. So the ccsr_rio structure should
be updated for those LIODN registers.

In addition, add a new macro "SET_SRIO_LIODN_BASE" to create
the SRIO LIODN ID table based on the SRIO LIODN register address.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

TWR-P1025 Specification:
-----------------------
Memory subsystem:
   512MB DDR3 (on board DDR)
   64Mbyte 16bit NOR flash
   One microSD Card slot

Ethernet:
   eTSEC1: Connected to Atheros AR8035 GETH PHY
   eTSEC3: Connected to Atheros AR8035 GETH PHY

UART:
   Two UARTs are routed to the FDTI dual USB to RS232 convertor

USB: Two USB2.0 Type A ports

I2C:
   AT24C01B 1K Board EEPROM (8 bit address)

QUICC Engine:
   Connected to DP83849i PHY supply two 10/100M ethernet ports
   QE UART for RS485 or RS232

PCIE:
   One mini-PCIE slot

Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[yorksun: Fixup include/configs/p1_twr.h]
Signed-off-by: York Sun <yorksun@freescale.com>

In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.

Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.

This patch fixes the issue.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>

This brings U-Boot's cpp invocation into line with the way the Linux
kernel invokes cpp on device trees. Consistency will be useful to ensure
*.dts is portable between the two.

-undef also has the added advantage of not defining "linux", so DT
property names such as "linux,keymap" don't get mangled.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Recent dtc supports #line directives in the input source code, and even
uses them to generate useful line numbers in any messages it emits. Stop
passing -P to cpp, since there's no need any more.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Now that nothing uses CONFIG_ARCH_DEVICE_TREE, stop defining it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Now that nothing uses the defines ARCH_CPU_DTS, BOARD_DTS, stop defining
them.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Now that we assume dtc supports the -i option, we don't need to use
ARCH_CPU_DTS in *.dts{,i}; we simply specify the include filename
directly, and dtc will find it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

*.dts may use #include (via cpp) or /include/ (via dtc; assuming a newer
dtc). The choice is up to the creator of the DT. Create a common variable
DTC_INCDIRS that lists the paths searched by include statements, and
update cpp and dtc invocation to use them.

For cpp, also specify -nostdinc to ensure the same set of paths is
available to both type of include statement.

For dtc, create a new DTC_FLAGS variable to hold all the flags passed to
dtc.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

The invocation of dtc is significantly more complex that it could be,
in order to work around an issue on old versions of dtc, which print
a message to stdout every time they run.

Remove this workaround, on the assumption that people have or will
upgrade to a newer version of dtc. This simplifies the build rule
significantly.

Related, split the invocation of cpp and dtc into separate commands
rather than a pipeline, so that if either fail, it is detected. This has
the nice benefit of saving off the result of the pre-processing step,
allowing it to be easily inspected.

Assuming a new enough dtc (which an earlier patch enforces), dtc will
parse #line directives in its input file, and generate correct file and
line numbers in error messages, even though cpp is unconditionally
applied to its input file.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Aside from microblaze, all other SoCs/boards/vendors store their DT files
in board/$vendor/dts/$soc-$board.dts. Move microblaze-generic.dts to this
location for consistency.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <monstr@monstr.eu>

Subsequent patches assume that dtc supports various recent features.
These are available in dtc 1.4.0. Validate that dtc is at least that
version.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Use DIV_ROUND_UP to simplify the code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Current code uses gd->baudrate before setting its value.
Besides, I got below build warning which is introduced by
commit ddb5c5be "blackfin: add baudrate to bdinfo".

board.c:235:3: warning: passing argument 1 of 'simple_strtoul' makes pointer from integer without a cast [enabled by default]
include/vsprintf.h:27:7: note: expected 'const char *' but argument is of type 'unsigned int'

This patch ensures we get the baudrate setting before using it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

The function return from P_FUNCT2MUX(per) takes 2 bits, however
for BF537_FAMILY with offset != 1 the function is 1 bit.

Also has small refactor for better readability.
In portmux_setup(), it looks odd having "muxreg &= ~(3 << 1);"
while in current code we do muxreg |= (function << offset);.

Signed-off-by: Axel Lin <axel.lin@ingics.com>

In special_gpio_free(), call unreserve() rather than reserve() to release gpio.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

In special_gpio_free(), call unreserve() rather than reserve() to release gpio.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

This commit adds some prototypes into include/mtd/cfi_flash.h.
These functions are defined with a weak attribute in
drivers/mtd/cfi_flash.c.
This means they can be overrided by board-specific ones
if necessary.

When defining such functions under board/ directory or
somewhere, cfi_flash.h should be included.
This makes sure that board-specfic cfi functions
are defined in a correct prototype.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Stefan Roese <sr@denx.de>

usb_lowlevel_init() allocates a new periodic_list each time it is invoked,
without freeing the original list. Since it is initialized later on in the code,
just reuse the first-allocated list in future invocations of usb_lowlevel_init.

Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>

When power cycling the hub ports, a misbehaving port will prevent all ports
from being powered on because we quit at the first sign of trouble.

Skip problematic ports instead of failing the entire power on.

Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>