Commit 7616e785 "Add Ethernet hardware MAC address framework to usbnet"
increased the code size and broke building for the ETX094 board.
Adjust the linker script to make it build again.

While we are at it, remove unused u-boot.lds.debug

Signed-off-by: Wolfgang Denk <wd@denx.de>

The PHY driver was too verbose and corrupted the boot message display
like this:

	...
	Net:   TSEC0 connected to Marvell 88E1111S
	TSEC1 connected to Marvell 88E1111S
	TSEC0, TSEC1
	...

Turn printf() into debug() so we het the expected output again:

	...
	Net:   TSEC0, TSEC1
	...

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>

* 'master' of git://git.denx.de/u-boot-sh:
  sh: add calling mmc_initialize in board.c
  sh: sh7757lcr: Add KEEP order to start.o section
  usb: r8a66597: Fix argument mistake of inl
  sh: Clean up rsk7264 board settings
  sh: sh2a: Add sh2a optimize to config.mk
  sh: Fix rsk7203 alignment problem
  sh: Add support for SH2A freestanding build
  sh: Add Renesas rsk7264 board

* 'master' of git://git.denx.de/u-boot-ubi:
  ubifs: Fix bad free() sequence in ubifs_finddir()

Some SH have MMC controller. So, if we need it, we have to call
the mmc_initialize().

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The sh7757lcr has a local u-boot.lds because the sh7757lcr is only
supported the SPI booting.
This patch refers from the commit "sh: Add KEEP order to start.o section"
(commit ID: b52da2ae).

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.

r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Adjusted default settings so that we can boot zImages and uImages.
Removed unused settings, use default commands and where possible
calculate all other settings.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Only the optimization of sh2 had been supported up.
This adds the optimization of sh2a.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

SH2A toolchains often only provide an fdpic version of libgcc. This
can't be used with bare-metal software like U-Boot, so this patch
provides the necessary functions extracted from libgcc.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Free private_data member element before freeing file structure.
This was causing malloc to crash. Also remove unnecessary variable
assigments as file structure gets free'd as well.

Signed-off-by: Rod Boyce <uboot@teamboyce.co.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

If you take a look at 96820a35, you'll see the original timeout was
CONFIG_SYS_HZ.  Which is 1000.  After the mentioned change, non-bulk timeout
was changed to 100.  This causes timeout failures on the dreamplug platform
when trying to initialize the usb microsd reader.

Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.

r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This is a small clean-up patch.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>

This describes what it is for, devices supported, how to enable for your
board in U-Boot, setting up the server, and notes about MAC addresses.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>

Built-in Ethernet adapters support setting the mac address by means of a
ethaddr environment variable for each interface (ethaddr, eth1addr, eth2addr).

This adds similar support to the USB network side, using the names
usbethaddr, usbeth1addr, etc. They are kept separate since we don't want
a USB device taking the MAC address of a built-in device or vice versa.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>

The SMSC95XX is a USB hub with a built-in Ethernet adapter. This adds support
for this, using the USB host network framework.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>

There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

On newer rev5 hardware the extension board EEPROM I2C address
has been changed to 0x54. Make this I2C address configurable
depending on CONFIG_DIGSY_REV5 so that extention board presence
detection works correctly on newer hardware.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

The U-Boot Design Principles[1] clearly say:

  Initialize devices only when they are needed within U-Boot, i.e. don't
  initialize the Ethernet interface(s) unless U-Boot performs a download
  over Ethernet; don't initialize any IDE or USB devices unless U-Boot
  actually tries to load files from these, etc. (and don't forget to
  shut down these devices after using them - otherwise nasty things may
  happen when you try to boot your OS).

So, do not initialize and read the sensors on startup.

Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>

* 'master' of git://git.denx.de/u-boot-arm:
  drivers/rtc: add Marvell Integrated RTC
  Armada100: Add Board Support for Marvell GuruPlug-Display
  Armada100: MFP macro naming correction
  arm: auto gen asm-offsets.h for mb86r0x
  spear: fix build errors for spear3xx/spear600 platforms
  cosmetic: arm: lib/board.c: Coding Style cleanup
  ARM: versatile: fix board support
  SMDKV310: Enable device tree support
  SMDKV310: MMC_SPL: Fix building when using "make O="
  arm: a320: enable tagged list support
  arm: a320: fix multiline comment style
  ARMv7: u8500_href: Add missing header to fix compiler warning
  Removed unused define, CONFIG_ARMV7.
  avr32: add grasshopper (ICnova AP7000) board
  AT91/SPI: fix atmel_dataflash_spi.c to allow building without warnings
  MAKEALL: remove AT91 boards that are in boards.cfg
  AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
  AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/master
  AT91: Board fix for AT91SAM9261-EK
  AT91: SoC fix at91sam9261_matrix.h
  AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
  AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/master
  AT91: change common at91sam9261 files to compile with new scheme
  AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)
  a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USART
  README: fix arm920t/at91 path
  net/eth.c: drop obsolete at91rm9200 support
  README.at91-soc: remove AT91(RM9200) joining notice
  a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warning
  MAKEALL: remove obsolete at91rm9200 soc
  ARM: remove obsolete at91rm9200
  omap4: clock init support for omap4460
  omap4: support TPS programming
  omap: reuse omap3 gpio support in omap4
  omap4: sdram init changes for omap4460
  omap4: add omap4460 revision detection
  mkimage: Add OMAP boot image support
  omap: add MMC and FAT support to SPL
  omap: add basic SPL support
  armv7: start.S: fixes and enhancements for SPL
  omap4: automatic sdram detection
  omap4: calculate EMIF register values
  omap4: add sdram init support
  omap4: add clock support
  omap4: add OMAP4430 revision check
  omap4: cleanup pin mux data
  omap4: utility function to identify the context of hw init
  DA8xx: fix LPSC constants
  DA8xx: switch an enum to defines for consistency
  DA8xx: add MMC/SD controller addresses
  DaVinci EMAC: declare function for all DA8xx CPUs
  DA8xx: add generic GPIO driver
  DaVinci: rename gpio_defs.h to gpio.h
  omap3evm: eth: Include functions only when necessary
  omap3evm: Update ethernet reset sequence for Rev.G board
  omap3evm: eth: split function setup_net_chip
  omap3: Include array definition only when it is used
  omap730p2: fix build breaks
  omap2420h4: fix build breaks
  omap1610inn: fix build breaks
  omap1510inn: fix build breaks
  omap5912osk: fix build breaks
  omap1610h2: fix build breaks

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Add detection of Coral-PA and configure Coral CCF an MMR parameters
using CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx_MMR macros.
Use CCF and MMR parameters for Coral-P Eval. Board if the appropriate
macros weren't defined.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device.  The device is attached to the LVDS port
on the P1022DS board.

The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that.  To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.

The data for the 800x600 video mode is originally from Jiang Yutang.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>

This driver can be used for kirkwood SoCs by enabling CONFIG_RTC_MV.  Tested on
Global Scale Technologies Dreamplug.

Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>

This patch adds basic board support with DRAM and UART functionality

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>

MFP macros for UART3 updated.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

auto gen asm-offsets.h for mb86r0x

Signed-off-by: Matthias Weisser <weisserm@arcor.de>

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Vipin Kumar <vipin.kumar@st.com>

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Albert Aribaud <albert.u.boot@aribaud.net>
cc: <macpaul@gmail.com>
cc: Wolfgang Denk <wd@denx.de>

Versatile board is used as example to run u-boot under qemu.
The patch fixes relocation for all versatile boards and adds
a versatileqemu target to be used under qemu.

Patch tested only under qemu, not on real boards.
Tested with QEMU emulator version 0.14.50.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Alessandro Rubini  <rubini-list@gnudd.com>
CC: Loïc Minier <loic.minier@linaro.org>

Enable passing a flattened device tree to the kernel.

Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>

Fixes dependency build error with "make O=" option.
"make O=" option is used to specify output directory.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>