ARM64 uses the newer RELA-style relocations rather than the older REL.
RELA relocations have an addend in the relocation struct, rather than
expecting the loader to read a value from the location to be updated.

While this is beneficial for ordinary program loading, it's problematic
for U-Boot because the location to be updated starts out with zero,
rather than a pre-relocation value.  Since we need to be able to run C
code before relocation, we need a tool to apply the relocations at
build time.

In theory this tool is applicable to other newer architectures (mainly
64-bit), but currently the only relocations it supports are for arm64,
and it assumes a 64-bit little-endian target.  If the latter limitation
is ever to be changed, we'll need a way to tell the tool what format
the image is in.  Eventually this may be replaced by a tool that uses
libelf or similar and operates directly on the ELF file.  I've written
some code for such an approach but libelf does not make it easy to poke
addresses by memory address (rather than by section), and I was
hesitant to write code to manually parse the program headers and do the
update outside of libelf (or to iterate over sections) -- especially
since it wouldn't get test coverage on things like binaries with
multiple PT_LOAD segments.  This should be good enough for now to let
the manual relocation stuff be removed from the arm64 patches.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Feng <fenghua@phytium.com.cn>

Signed-off-by: David Feng <fenghua@phytium.com.cn>

Signed-off-by: David Feng <fenghua@phytium.com.cn>

Signed-off-by: David Feng <fenghua@phytium.com.cn>

Byte offset of Ethernet mac address read from e-fuse are wrong so DHCP is
not working on some boards, modifying the offset to read properly.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>

Following commit "arm: omap3: Enable clocks for peripherals only if they are
used" (f33b9bd3) it is now necessary to enable
clocks for GPIO banks explicitly. On cm_t35, GPIO bank 5 is necessary for
scf0403 lcd support.

Enable GPIO bank 5 clocks.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

Commit f33b9bd3 breaks boards
which do not explicitly enable the gpio clocks. This causes
the twister spl to hang, since it uses the no longer enabled
gpio 55. Add CONFIG_OMAP3_GPIO_2 to unbrick the board.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Stefano Babic <sbabic@denx.de>

commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30, "mtd: nand:
omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme"
removed CONFIG_SPL_NAND_SOFTECC from the tam3517 common config,
causing the spl nand boot to fail. Add it back, so derived
boards boot again.

Cc: Pekon Gupta <pekon@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Raphael Assenat <raph@8d.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Stefano Babic <sbabic@denx.de>

The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.

Signed-off-by: Tom Rini <trini@ti.com>

With the changes to make OOBFREE/ECCPOS configurable but default to
larger, we need to set these config options for the space savings they
provide.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>

Due to the i2c mux rework in u-boot we now have only to specify the
busnumber and not the whole mux configuration.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>

The board is similar to the standard km_kirkwood board. From a
u-boot point of view, the only difference is an increased
256 MiB DRAM (128M16). A board based on this design is for
example the SUP12.

Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>

Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>

Conflicts:
	include/micrel.h

The conflict above was trivial, caused by four lines being
added in both branches with different whitepace.

Enable fuse supply before fuse programming and disable after.

Signed-off-by: Sergey Alyoshin <alyoshin.s@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

The enable_fec_anatop_clock method should be available for all MX6
variant as it is not MX6 SoloLite specific. This moves the code out of
the #ifdef/#endif and we make it conditional to CONFIG_FEC_MXC
instead.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>

This patch fixes allow for the DeviceTree and initrd relocation fixing
the boot of FSL 3.10.9-1.0.0-alpha kernel.

This changes following boards:

 - mx6sabreauto
 - mx6sabresd
 - wandboard
 - udoo
 - nitrogen6x
 - cgtqmx6eval

The reasoning, as explained by Hui Liu, is:

,----
| The FDT blob will be placed at DDR physical addr: 0x11000000. When Linux kernel
| Boot up, it will decompress the compressed kernel image and place the decompressed
| kernel image at the low end of the DDR memory and start running from it. If the
| decompressed kernel image is bigger for example than 16M, it may over written the
| fdt blob which u-boot loaded to the DDR memory @0x11000000 with fdt_addr=0x11000000
|
| To expand the fdt_addr from 0x11000000 to 0x18000000, which can avoid the override
| Since we will not likely have one kernel image larger than 128MB.
`----

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>

This adds following new targets:

 - update_nand_kernel
 - update_nand_fdt
 - update_nand_filesystem

and to avoid confusion, the 'update_nand_full' has been renamed to
'update_nand_firmware_full'.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>

This reads the kernel, ftd and boot into ubifs filesystem. While on
that, the SD firmware filename definition has been moved next to the
other SD related commands.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

Using 512k for fdt partition allow it to be aligned with the other
small partitions and 512k erase block size.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>

The macro allows easy setting in per-pin, as for example:

,----
| imx_iomux_v3_setup_pad(MX6_PAD_NANDF_D1__GPIO_2_1 | MUX_MODE_SION);
`----

The IOMUX_CONFIG_SION allows for reading PAD value from PSR register.

The following quote from the datasheet:

,----
| ...
| 28.4.2.2 GPIO Write Mode
| The programming sequence for driving output signals should be as follows:
| 1. Configure IOMUX to select GPIO mode (Via IOMUXC), also enable SION if need
| to read loopback pad value through PSR
| 2. Configure GPIO direction register to output (GPIO_GDIR[GDIR] set to 1b).
| 3. Write value to data register (GPIO_DR).
| ...
`----

This fixes the gpio_get_value to properly work when a GPIO is set for
output and has no conflicts.

Thanks for Benoît Thébaudeau <benoit.thebaudeau@advansee.com>, Fabio
Estevam <fabio.estevam@freescale.com> and Eric Bénard
<eric@eukrea.com> for helping to properly trace this down.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>

As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.

Also, as the timer is still not available when arch_cpu_init() is called, we
need to call it later at board_postclk_init() phase.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Introduce set_ldo_voltage() so that all three LDO regulators can be configured.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

mx6 datasheet specifies that the minimum VDDSOC at 792 MHz is 1.15 V.
Add a 25 mV margin and set it to 1.175V.

This also matches the VDDSOC voltages for 792MHz operation that the kernel configures:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/cpu_op-mx6.c?h=imx_3.0.35_4.1.0



Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Since ROM may modify the LDO ramp up time according to fuse setting,
it is safer to reset the ramp up field to its default value of 00:

00: 64 cycles of 24MHz clock;
01: 128 cycles of 24MHz clock;
02: 256 cycles of 24MHz clock;
03: 512 cycles of 24MHz clock;

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

set_vddsoc() is not used anywhere else, so make it static.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Add CONFIG_CMD_FUSE option, so that the fuse API can be used.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

When using the fuse API in U-boot user must calculate the 'bank' and 'word'
values.

Provide a real example on how to calculate such values for the mx6q.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

This patch add uuid disk to defualt partions necessary to
restore gpt partitions and fixes mmcdev environmental variable.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This fix is necessary after increased by one the number
of adapters in s3c24x0 driver.

Tested on Trats and Trats2.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

When variable size SPL is used, the BL1 expects the SPL to be
encapsulated differently: instead of putting the checksum at a fixed
offset in the SPL blob, prepend the blob with a header including the
size and the checksum.

The enhancements include
	- adding a command line option, '--vs' to indicate the need for the
	variable size encapsulation
	- padding the fixed size encapsulated blob with 0xff instead of random
	memory contents
	- do not silently truncate the input file, report error instead
	- no need to explicitly closing files/freeing memory, this all happens
	on exit; removing cleanups it makes code clearer
	- profuse commenting
	- modify Makefile to allow enabling the new feature per board

Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Adding initial config for SMDK5420 to build and boot U-Boot
over Exynos based SMDK5420.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch adds dts support for SMDK5420.
exynos5.dtsi created is a common file which has the nodes common
to both 5420 and 5250.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Adds code in pinmux and gpio framework to support Exynos5420.

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch intends to add DDR3 initialization code for Exynos5420.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>