Add support for the Kona SDHCI found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Add support for the Kona I2C controller found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Add support for the Kona GPIO controller found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Add bcm281xx architecture support code including a clock framework and
chip reset.  Define register block base addresses for the bcm281xx
architecture and create an empty gpio header file required when
CONFIG_CMD_GPIO is set.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as
much as possible. This will aid in a future patch which will create a
common header e.g. config_distro_bootcmd.h.

While at it, enable booting from extlinux.conf using the sysboot command.

The iteration and componentization currently makes a little more sense
for Tegra than RPi, but I'd still like to keep the two as similar as
possible. USB and networking support is coming to the RPi in due course,
and it'll all make more sense then anyway.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

The Pi has no flash to store an environment in the usual fashion. However,
the user may wish to customize the environment. We know that the SD card
must be present, since that's where the boot ROM has loaded U-Boot from.
So, load uEnv.txt from there early during boot. This allows the user to
e.g. customize boot_targets, in order to automatically select network
boot.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

Modify the rpi_b board to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the rpi_b.h.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

pxe.c provides both the "pxe" command which relies on a network, and the
"sysboot" command which doesn't. Fix the file to compile when network
support isn't enabled. This is useful e.g. on the Raspberry Pi which has
no network support yet, but will soon support the sysboot command.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.

Signed-off-by: Tom Rini <trini@ti.com>

In Kbuild, every makefile must have non-empty obj- or obj-y.
Otherwise, built-in.o will not be created and the link stage
will fail.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

There is a strange comment in fit_image_load().
This function can be used for loading Kernel Image, FDT
as well as ramdisk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

If the whole code is surrounded by #ifdef(CONFIG_ ) .. #endif,
it should be moved to Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

- When CONFIG_DISPLAY_CPUINFO is not enabled,
   print_cpuinfo() should be defined as an empty function
   in a header, include/common.h

 - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
   from caller, common/board_f.c and arch/arm/lib/board.c

 - Remove redundant prototypes in arch/arm/lib/board.c,
   arch/arm/include/asm/arch-am33x/sys_proto.h and
   board/nokia/rx51/rx51.h, keeping the one in include/common.h

 - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
   where it is missing

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

CONFIG_SYS_GBL_DATA_SIZE is not used any more.
The size of struct "global_data" is automatically calculated
by asm-offsets. (See lib/asm-offsets.c)

GENERATED_GBL_DATA_SIZE should be used instead of
CONFIG_SYS_GBL_DATA_SIZE.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

It is convenient to have all device trees on the same SoC compiled.
It allows for later easy repackaging without the need to re-run
the make file.

  - Build device trees with the same SoC under arch/$(ARCH)/dts

  - Copy the one specified by CONFIG_DEFAULT_DEVICE_TREE or
    DEVICE_TREE=... to dts/dt.dtb

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.

I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.

For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.

This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Useful rules in scripts/Makefile.lib allows us to easily
generate a device tree blob and wrap it in assembly code.

We do not need to parse a linker script to get output format and arch.

This commit deletes ./u-boot.dtb since it is a copy of dts/dt.dtb.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

- Delete fs.xml from DOCBOOKS to fix an error.
     Commit e3ff797c added fs.xml to DOCBOOKS
     but missed to add doc/DocBook/fs.tmpl.
  - Fix the location of include guard in include/linker_lists.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Abraham Varricatt <abraham.varricatt@vvdntech.com>
Acked-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>

tools/kernel-doc/docproc.c and tools/kernel-doc/kernel-doc are
files imported from Linux Kernel.

They originally resided under scripts/ directory in Linux Kernel.

This commit moves them to the original location.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>

Commit bb02c536 stopped creaing a symbolic link include/asm.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

fw_printenv is a program which mostly runs on the target Linux.

Before switching to Kbuild, we needed to set HOSTCC at the
command line like this:
    make HOSTCC=<your CC cross-compiler> env

Going forward we can cross compile it by specifying CROSS_COMPILE:
    make CROSS_COMPILE=<your cross-compiler prefix> env
This looks more natural.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>

Without this workaround, you will see a lot of ".*.su" files
at the top directory after building with a compiler
which supports "-fstack-usage" option.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

We had switched to Kbuild, so we do not need to
delete sandburst board files at every build.

U-Boot conventional build system did not check the
update of command line option, -DBUILDUSER.

Kbuild can handle it nicely and re-builds object files
when command line options are changed.
(The file ".*.cmd" stores the information how the file
was generated at the previous build.)

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

For out-of-tree build
  - Check if the source tree is clean
  - Create a Makefile in the output directory

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

This commit fixes two problems:

[1] We could not do board configuration and "make all"
    in one command line.

For example, the following did not work as we expect:
  $ make sandbox_config all
  Configuring for sandbox board...
  make: Nothing to be done for `all'.

[2] mixed-target build did not work with -j option

For example, the following did not work:
  $ make -j8 sandbox_config u-boot
  Makefile:481: *** "System not configured - see README".  Stop.
  make: *** [u-boot] Error 2
  make: *** Waiting for unfinished jobs....
  Configuring for sandbox board...

Going forward, we can do
  $ make -j8 sandbox_config all

This is the same as
  $ make sandbox_config
  $ make -j8

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

This commit refactors cleaning targets such as
clean, clobber, mrpropper, distclean
with scripts/Makefile.clean.

By using scripts/Makefile.clean, we can recursively descend
into subdirectories and delete generated files there.

We do not need add a big list of generated files
to the "clean" target.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

- Move "easylogo", "gdb" tagets to tools/Makefile
 - Delete "gdbtools" target (same as "gdb")

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

$(MTD_VERSION) is used in tools/env/Makefile

If you specify a variable at a command line like:
  $ make MTD_VERSION=old env
or specify it thru an envrionment variable like:
  $ export MTD_VERSION=old
  $ make env
it is inherited to the sub-make too.
We do not need to pass it from the top Makefile explicitely.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

This commit refactors rules of directory descending
and defines u-boot-dirs and u-boot-all-dirs.
(We will need u-boot-all-dirs when using
scripts/Makefile.clean)

Additionally, rename LIBS-y to libs-y.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

This commit changes the top Makefile to handle various targets
nicely.
Make targets are divided into four categories:

 - mixed-targets
     We can call a configuration target and build targets
     at one command line like follows:
     $ make <board_name>_config u-boot

     They are handled one by one.

 - config targets
     <board_name>_config

 - no-dot-config-targets
     Targets we can run without board configuration such as
       clean, mrproper, distclean, TAGS, %docs, etc.

 - build targets
     The other target which need board configuration.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Before this commit, "make tidy" did
"make clean" + delete "*.depend*" files.

But, we do not have "*.depend*" files any more,
which means "make tidy" is the same as "make clean".

This commit removes the redandant target "tidy".

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Before this commit, {spl,tpl}-autoconf.mk was always generated
at the top Makefile even if SPL(TPL) build was not selected.

This commit moves the build rule of {spl,tpl}-autoconf.mk
from the top Makefile to spl/Makefile.
It prevents unnecessary {spl,tpl}-autoconf.mk from being
generated.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

This commit changes the location of include directives
of board configuration files.

The purpose of this change is:
 - Slim down $(TOPDIR)/config.mk
 - Prevent $(TOPDIR)/Makefile from including the same
    configuration file twice
 - Do not include include/config.mk multiple times
    because ARCH, CPU, BOARD, VENDOR, SOC are exported

Before this commit:

 - include/autoconf.mk was included from $(TOPDIR)/Makefile
   and $(TOPDIR)/config.mk
   (This means $(TOPDIR)/Makefile included include/autoconf.mk twice)

 - include/{spl,tpl}-autoconf.mk was included from $(TOPDIR)/config.mk

 - include/config.mk was included from $(TOPDIR)/Makefile
   and $(TOPDIR)/config.mk
   (This means $(TOPDIR)/Makefile included include/config.mk twice)

After this commit:

 - include/autoconf.mk is included from $(TOPDIR)/Makefile
   and $(TOPDIR)/scripts/Makefile.build

 - include/{spl,tpl}-autoconf.mk is included from $(TOPDIR)/spl/Makefile
   and $(TOPDIR)/scripts/Makefile.build

 - include/config.mk is included from $(TOPDIR)/config.mk and
   $(TOPDIR)/spl/Makefile

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

We can get Kbuild-ish log style like this:
  GEN     include/autoconf.mk
  GEN     include/autoconf.mk.dep

We do not need XECHO any more.

And also change checkstack target like Linux Kernel.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>