When using the fuse API in U-boot user must calculate the 'bank' and 'word'
values.

Provide a real example on how to calculate such values for the mx6q.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

Commit 164d9846 breaks
board with SATA support, because sata is not compiled.

Signed-off-by: Stefano Babic <sbabic@denx.de>

ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache

Signed-off-by: Huang yongcai <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>

According to NOTE in strtoul(3), the errno must be zeroed before strtoul()
is called. Zero the errno. The NOTE reads as such:

  Since strtoul() can legitimately return 0 or ULONG_MAX (ULLONG_MAX for
  strtoull()) on both success and failure, the calling program should set
  errno  to  0  before the call, and then determine if an error occurred
  by checking whether errno has a nonzero value after the call.

This issue was detected on Fedora 19 with glibc 2.17 .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>

mx6sabresd boards have a 18-bit LVDS data width and the correct color format
is RGB666.

Suggested-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

HSYNC, VSYNC and DISP_CLK are very useful display signals for debugging.

Configure them as active pins.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:

"Controls the frequency of the ethernet reference clock.
- 00 - 25MHz
- 01 - 50MHz
- 10 - 100MHz
- 11 - 125MHz"

Current logic does not handle the 25MHz case correctly, so fix it.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

This patch adds support for the AMPIRE 800x480 LCD panel that is available
for M53EVK.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

Align with the context to use readl() to read the CCM_CCGR3
register with memory barrier instead of __raw_readl().

Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

The CPU errata expressed in include/configs/mx6_common.h apply
to all i.MX6DQ and i.MX6DLS parts.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>

According to the README:

"- CONFIG_SYS_SPD_BUS_NUM
		If SPD EEPROM is on an I2C bus other than the first
		one, specify here. Note that the value must resolve
		to something your driver can deal with."

There is no SPD EEPROM on the imx boards, so ged rid of this option.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>

Add SATA support on uDoo Board.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>

Move setup_sata function definition from platform file nitrogen6x.c
to arch/arm/imx-common/sata.c to avoid code duplication.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>

This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.

All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
    MX6Q   - for boards targeting i.MX6Q or i.MX6D
    MX6DL  - for boards targeting i.MX6DL
    MX6S   - for boards targeting i.MX6S
    MX6QDL - for boards that support any of the above with
             run-time detection

Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>

The pmic_init() function has the I2C or SPI bus number that is connected to the
PMIC.

Instead of passing I2C_PMIC, explicitly pass the I2C bus number via I2C_x
definition.

The motivation for doing this is to avoid people just doing a copy and paste
of I2C_PMIC into their board file when another I2C bus is actually used to
interface to their PMIC.

This also makes more obvious which is the I2C bus connected to the PMIC, without
having to search in the source code for the meaning of the 'I2C_PMIC' number.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>

uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds.
To disabled watchdog during kernel boot, WDI pin of that chip needs to be
in "high impedance" state. I.mx6 gpio configuration does not contemplate
tristate, so pin is set as input in high impedance.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>

Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031).
Ethernet speed is currently limited to 10/100Mbps.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>

Previous uDoo configuration adopts register settings for DDR3, clock, muxing,
etc. taken from Nitrogen6x. uDoo schematics is rather different from that board,
and it needs customized setting for most of the registers.
All this changes can be considered atomical since it is part of initial support
of the board.

Patch changes uDoo configuration files path to a specific one, and adopt
optimized value for every configured register.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>

mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port.

Add support for it.

This patch allows the SPI NOR flash to be succesfully detected:

=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Currently HDMI splash screen is selected by default on mx6sabresd boards.

As LVDS is also enabled, this causes incorrect colors to be displayed im the
LVDS panel.

Fix this by selecting the LVDS panel as the default splash output and only keep
HDMI or LVDS turned on at the same time.

Acked-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

There is no need to pass p->bus differently when the PMIC is connected via SPI
or via I2C.

Handle the both cases in the same way.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

On efikamx board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.

Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

On mx31pdk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.

Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

On mx51evk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.

Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

OCOTP driver is currently selected via CONFIG_MXC_OCOTP option.

Remove the old OCOTP related options, as they are not used anymore.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>

The fec_halt() never free'd both RX and TX DMA descriptors that
were allocated in fec_init(), nor did it free the RX buffers.
Rework the FEC driver so that these descriptors and buffers are
allocated only once in fec_probe().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

Since the titanium board is not a Freescale board, move its
BSP code from the freescale board directory to the newly created
barco board directory.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>

When cpu_eth_init() fails we should not return success.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>

When cpu_eth_init() fails we should not return success.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

If ipuv3_fb_init() fails, we should return the error immediately.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Setting the direction and an output value should be done by
1) set the desired output value,
2) switch to output.

If this is done in the inverse order, there can be a glitch on
the GPIO line.

This patch fixes this by using the order as described above.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefano Babic <sbabic@denx.de>

There is no real benefit in adding the board name into U-boot's prompt, so
remove the custom CONFIG_SYS_PROMPT definitions so that the standard "=> "
prompt is used across FSL boards.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
  - add splashpos=m,m to default environment, so splash screen is always
    centered.
  - adapt environment for bootcount feature
  - add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
  store the bootcount in the environment, as we have no softreset
  save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
  bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
  Add for the siemens boards the possibility to define in dfu mode,
  the iSerialNumber and the bcdDevice fields in the USB Device
  descriptor.
- fix upgrade mechanism based on bootcount
  Correct location of saveenv and remove not active variable.

  Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
  reboot board in case of empty kernel partition. Without
  these defines an empty kernel partition leads to an
  abort of boot process and one remains in u-boot prompt.

- general cleanup of dxr2, pxm2 and rut boards
  all:
   * Remove net boot from bootcmd
     Ping can cause a crash on boards without ethernet phy.
     net_nfs command is used only for development

   * Add reset at the end of bootcmd
     In order to have an immediate reset of the boot when bootcmd
     fails, add reset at the end of bootcmd.

  rut:
   * add nand_img_size

  dxr2:
   * update nand_img_size

   * ddr3 timings updated with iocontrol property that can be
     modified via eeprom. New default parameters from software
     leveling with draco ES2.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Pascal Bach <pascal.bach@siemens.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Michel <matthias.michel@siemens.com>
Cc: Tom Rini <trini@ti.com>

add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>