Enable drivers for FIMD, DP and parade bridge chip.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch adds DT properties for fimd and the parade bridge chip
present on peach_pit. The panel supports 1366x768 resolution.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Add initialization code for peach_pit panel, parade bridge chip,
and backlight.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch adds missing declaration for gpio_direction_input
function, thereby helps in resolving compilation warnings.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

The initialization table comes from the "Illustration of I2C command
for initialing PS8625" document supplied by Parade.

Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

On Exynos5420 and newer versions, the FIMD sysmmus are in
"on state" by default.
We have to disable them in order to make FIMD DMA work.
This patch adds the required framework to exynos_fimd driver,
and disables FIMD sysmmu on Exynos5420.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420 needed by
exynos video driver.
Also, configure ACLK_400_DISP1 as the parent for MUX_ACLK_400_DISP1_SUB_SEL.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

RPLL is needed to drive the LCD panel on Exynos5420 based boards.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.

Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch changes MPLL from 800MHz to 880MHz on Odroid.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Inderpal's email address is not working any more.
Chander will be a new maintainer.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This config is valid for two devices:
- Odroid X2,
- Odroid U3.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This is a standard description for Odroid boards.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This board file supports standard features of Odroid X2 and U3 boards:
- Exynos4412 core clock set to 1000MHz and MPLL peripherial clock set to 800MHz,
- MAX77686 power regulator,
- USB PHY,
- enable XCL205 - power for board peripherials
- check board type: U3 or X2.
- enable Odroid U3 FAN cooler

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This change adds setup of environmental board info using
get_board_name() and get_board_type() functions for config
CONFIG_BOARD_TYPES.

This is useful in case of running many boards with just one config.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This change adds declaration of functions:
- set_board_type() - called at board_early_init_f()
- get_board_type() - called at checkboard()

For supporting multiple board types in a one config - it is welcome
to display the current board model. This is what get_board_type()
should return.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

On an Odroid U3 board, the SOC is unable to reset the eMMC card
in the DWMMC mode by the cpu software reset. Manual reset of the card
by switching proper gpio pin - fixes this issue.

Such solution needs to add a call to pre reset function.
This is done by the reset_misc() function, which is called before reset_cpu().
The function reset_misc() is a weak function.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>

Changes v4:
- arch/arm/reset: fix weak function attribute to proper style
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This change enable automatic setting of dfu alt info
on every boot. This is useful in case of booting one
u-boot binary from multiple media.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This change introduces new common function:
- set_dfu_alt_info() - put dfu system and bootloader setting
                       into $dfu_alt_info.
functions declaration:
- char *get_dfu_alt_system(void)
- char *get_dfu_alt_boot(void)
- void set_dfu_alt_info(void)
and new config:
- CONFIG_SET_DFU_ALT_INFO

This function can be used for auto setting dfu configuration on boot.
Such feature is useful for multi board support by one u-boot binary.
Each board should define two functions:
- get_dfu_alt_system()
- get_dfu_alt_boot()

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

It is possible to boot device using a micro SD or eMMC slots.
In this situation, boot device should be registered as a block
device 0 in the MMC framework, because CONFIG_SYS_MMC_ENV_DEV
is usually set to "0" in the most config cases.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This patch introduces code clean-up for exynos boot mode check.
It includes:
- removal of typedef: boot_mode
- move the boot mode enum to arch-exynos/power.h
- add bootmode for sequence: eMMC 4.4 ch4 / SD ch2
- add new function: get_boot_mode() for OM[5:1] pin check
- update spl boot code

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>

Changes v5:
- exynos: boot mode: add missing bootmode (1st:EMMC 4.4 / 2nd:SD ch2)

Changes v6:
- none

changes v7:
- change boot mode name: BOOT_MODE_MMC to BOOT_MODE_SD
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

This change fixes the bad gpio configuration for the exynos dwmmc.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

The byte order of soc revision was inverted, now it is fixed.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: Tom Rini <trini@ti.com>

When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---

Signed-off-by: Bo Shen <voice.shen@atmel.com>

When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---

Signed-off-by: Bo Shen <voice.shen@atmel.com>

This allows the USB code to determine whether a USB bus reset was issued,
which in turn allows the code to differentiate between a detach (return
to shell prompt) and a board reset/reboot request.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

New dfu_usb_get_reset() method is necessary to distinct two different
use cases of dfu-util program.
This method checks if the USB bus reset has been really performed after
DFU DETACH.

Without this function the previous DFU behavior is preserved.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>

This commit provides distinction between DFU device detach and reset.
The -R behavior is preserved with proper handling of the dfu-util's -e
switch, which detach the DFU device.

By running dfu-util -e; one can force device to finish the execution of
dfu command on target and execute some other scripted commands.

Moreover, some naming has been changed - the dfu_reset() method now is known
as dfu_detach(). New name better reflects the purpose of the code.

It was also necessary to increase the number of usb_gadget_handle_interrupts()
calls since we also must wait for detection of the USB reset event.

Example usage:
1. -e (detach) switch
 dfu-util -a0 -D file1.bin;dfu-util -a3 -D uImage;dfu-util -e

 access to u-boot prompt.

2. -R (reset) switch
 dfu-util -a0 -D file1.bin;dfu-util -R -a3 -D uImage

 target board reset

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>

Some drivers (e.g. net/e1000) reference these functions. So, this
fixes the build of MVBC_P board.

I'm not familiar with the MPC5xxx platform, maybe a full
implementation shall be implemented instead of this stub in the
future.

Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>, Marek Vasut <marex@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>

Add a bank of GPIOs for sandbox which can be used for testing this
functionality.

Signed-off-by: Simon Glass <sjg@chromium.org>

The gpio command mostly relies on gpio_request() and gpio_free() being
nops, in that you can request a GPIO twice. With driver model this is
now implemented correctly, so it fails.

Change the command to deal with a failure to claim the GPIO.

Signed-off-by: Simon Glass <sjg@chromium.org>

The GPIO list is very long in many cases and most of them are not used.
By default, show only the GPIOs that are in use, and provide a flag to show
all of them. This makes the 'gpio status' command much more pleasant.

In order to do this, driver model now exposes a method for obtaining the
'function' of a GPIO, which describes whether it is an input or output, for
example. Implementation of this method is optional.

Signed-off-by: Simon Glass <sjg@chromium.org>

The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.

Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file.  As a result, some boards added just before
the merge were lost.

This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>

Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Move Highbank-specific settings to highbank/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rob Herring <robh@kernel.org>