There's no sensible reason to unite speed and interface type into
one variable.  So split this variable enet_interface into two
vars: enet_interface_type, which hold the interface type and speed.

Also: add the possibility for switching between 10 and 100 MBit
interfaces on the fly, when running in FAST_ETH mode.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Normally the processor clock has a divisor of 2.
In some cases this this needs to be set to 4.
Check the user has set environment mdiv to 4 to change the divisor.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

SPEAr320 SoC support contains basic spear320 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)

Signed-off-by: Vipin <vipin.kumar@st.com>

SPEAr310 SoC support contains basic spear310 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)

Signed-off-by: Vipin <vipin.kumar@st.com>

SPEAr310 and SPEAr320 SoCs contain an EMI controller to interface
Paraller NOR flashes. This patch adds the support for this IP

The standard CFI driver is used to interface with NOR flashes

Signed-off-by: Vipin <vipin.kumar@st.com>

SPEAr300 SoC support contains basic spear300 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver

Signed-off-by: Vipin <vipin.kumar@st.com>

This patch adds the  support to read and write mac id from i2c
memory.
For reading:
	if (env contains ethaddr)
		pick env ethaddr
	else
		pick ethaddr from i2c memory
For writing:
	chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
	in i2c memory

Signed-off-by: Vipin <vipin.kumar@st.com>

SPEAr600 SoC support contains basic spear600 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver

Signed-off-by: Vipin <vipin.kumar@st.com>

A newer CPLD version on the 405EX evaluation board requires a different
EBC controller setup for the CPLD register access. This patch adds a CPLD
version detection for Kilauea and code to reconfigure the EBC controller
(chip select 2) for the old CPLD if no new version is found.

Additionally the CPLD version is printed upon bootup:

Board: Kilauea - AMCC PPC405EX Evaluation Board (CPLD rev. 0)

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Cc: Zhang Bao Quan <bqzhang@udtech.com.cn>

- malloc size 4 MB for all keymile boards
- use generic FDT code for fixing up the DTS
- enable unit-led at startup for keymile boards
- remove some dts updates for keymile boards
- ppc_83xx, kmeter1: take FE/GbE PHYs out of reset
- ppc_83xx, kmeter1: change from Intel Strata to Spansion 64MB flash
  changed from Intel Strata to Spansion 64MB flash and changed flash layout.
+---------+----------+-----------------------+-----------------------------+
| name    | size     | range                 | description                 |
+---------+----------+-----------------------+-----------------------------+
| u-boot  |   768 KB | 0xf0000000-0xf00bffff | for u-boot                  |
| env     |   128 KB | 0xf00c0000-0xf00dffff | for environment             |
| envred  |   128 KB | 0xf00e0000-0xf00fffff | for environment (redundant) |
| ubi0    | 64512 KB | 0xf0100000-0xf3ffffff | ubi0 for ubi volumes        |
+---------+----------+-----------------------+-----------------------------+

Signed-off-by: Heiko Schocher <hs@denx.de>

When referring to PCIe and USB 'endpoint' is the standard naming
convention.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>

Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The new board revision has a different LCD.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Give the CF/IDE code its own file to keep things cleanly separated.  While
we're here, clean up the code to use common functions.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

While the initdram() function makes sense on some arches, it doesn't for
Blackfin systems as it's always implemented the same way.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

USB0_DRVVBUS pinmux configuration is required for USB functinality
in uboot.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>

Remove PCI reset, if there is a monarch PMC module.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

convert clrbits_be32 + setbits_be32 to clrsetbits_be32, use out_be32 to set gcr.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

changed to use mkconfig -t option instead, plus misc codingstyle fixes.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The core support for NAND booting is there already, so this patch
is pretty straightforward.

There is one trick though: top level Makefile expects nand_spl to
be in nand_spl/board/$(BOARDDIR), but we can fully reuse the code
from mpc8313erdb boards, and so to not duplicate the code we just
symlink nand_spl/board/freescale/mpc8315erdb to mpc8313erdb.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

o silence make during ln echo
o update documentation
o and avoid:

$ ./MAKEALL MPC8315ERDB_NAND
Configuring for MPC8315ERDB board...
sdram.o: In function `fixed_sdram':
/home/r1aaha/git/u-boot/nand_spl/board/freescale/mpc8313erdb/sdram.c:72: undefined reference to `udelay'

by renaming udelay -> __udelay in the spirit of commit
3eb90bad "Generic udelay() with watchdog
support".

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Thanks to "Errata to MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual, Rev. 0" document, which describes all eSDHC
pins, we can add 4-bits eSDHC support for MPC8569E-MDS boards.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We already map the page cache-inhibited.  There is no reason we
shouldn't also be marking it guarded to prevent speculative accesses.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Rather than hard coding which TLB entry the FLASH is mapped with we can
use find_tlb_idx to determine the entry.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We can use fsl_setup_hose to determine if we are a agent/end-point or
a host.  Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We can use fsl_setup_hose to determine if we are a agent/end-point or
a host.  Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We can use fsl_setup_hose to determine if we are a agent/end-point or
a host.  Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We can use fsl_setup_hose to determine if we are a agent/end-point or
a host.  Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Davinci: Table driven pinmux configuration

Add code to allow pinmux_config tables to be grouped and configured
as a single resource. This removes multiple calls to the pinmux
configuration code from board_init and allows pinmuxes to be
individually configured and added by data manipulation only.

All related #ifdefs can the be removed from board_init code and
since the compiler optimises away statics, #ifdefs can be reduced in
the data definitions as well.

Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>

These regulators are not needed to start the kernel and only
cause "incomplete constraints" warnings from kernel, so don't
turn them on to save power.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>

Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().

Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>