- May 27, 2016
-
-
Robert P. J. Day authored
In order for CONFIG_IS_ENABLED(FOO) to work we need to move the changes that CONFIG_FIT_DISABLE_SHA256 makes to be prior to the evaluation by CONFIG_IS_ENABLED(foo) Signed-off-by:
Robert P. J. Day <rpjday@crashcourse.ca> [trini: Move CONFIG_FIT_DISABLE_SHA256 parts to fix build breakage] Signed-off-by:
Tom Rini <trini@konsulko.com>
-
Masahiro Yamada authored
Since 1e6ad55c ("armv8/cache: Change cache invalidate and flush function"), this routine can be used for both cache flushing and cache invalidation. So, it is better to not include "flush" in this routine name. Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com>
-
Masahiro Yamada authored
We should say "clean & invalidate", or simply "flush". Signed-off-by: -
Masahiro Yamada authored
__asm_dcache_all can directly return to the caller of __asm_{flush,invalidate}_dcache_all. We do not have to waste x16 register here. Signed-off-by:York Sun <york.sun@nxp.com>
-
Lokesh Vutla authored
Different AM335x based platforms have different serial consoles. As serial console is Kconfig option a separate defconfig has to be created for each platform. So pass the serial device dynamically. Signed-off-by:Lokesh Vutla <lokeshvutla@ti.com>
-
Lokesh Vutla authored
Add minimal dts support for AM335x-ICEv2 board Reviewed-by:
Roger Quadros <rogerq@ti.com>
-
Lokesh Vutla authored
Populate the right dtb file and console for AM335x-ICEv2 board. Reviewed-by:
-
Lokesh Vutla authored
In order to enable cpsw on AM335x ICEv2 board, the following needs to be done: 1)There are few on board jumper settings which gives a choice between cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting this, there are few GPIOs which control these muxes that needs to be held high. 2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected via I2C. This needs to properly programmed and locked for PHY operation. And PHY needs to be reset before before being used, which is also held by a GPIO. 3) RMII mode needs to be selected. [1] http://www.ti.com/lit/zip/tidr336 [2] http://www.ti.com/lit/ds/symlink/cdce913.pdf Reviewed-by:
Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by:
-
Lokesh Vutla authored
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost, high performance , programmable clock synthesizers. They generate upto 3 output clocks from a single input frequency. Each output can be programmed for any clock-frequency. Adding support for the same. Reviewed-by:
-
Lokesh Vutla authored
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125), capable of running at 400MHz. Adding this specific DDR configuration details running at 400MHz. Reviewed-by:
-
Lokesh Vutla authored
Add necessary pinmux support for AM335x ICEv2 board. Reviewed-by:
-
Lokesh Vutla authored
Similar to other TI's AM335x platforms, AM335x ICEv2 also has an eeprom populated for its unique identification. Adding this info so that AM335x ICEv2 specific initialization can be done. Reviewed-by:
-
Tom Rini authored
Re-org env sections so that we can fall back to env is in FAT on SD card, for broader board compatibility Signed-off-by:
Tom Rini <trini@ti.com> Signed-off-by:
-
Lokesh Vutla authored
Add initial DTS support for AM335x-BBG Reviewed-by:
-
Lokesh Vutla authored
Add initial DTS support for AM335x-evm sk. Reviewed-by:
-
Mugunthan V N authored
As per mmc device tree binding documentation card detect gpio has to be active low signal. When a hardware is designed with active high card detect, gpio polarity has to be changed with cd-inverted dt property. In AM335x the card detect gpio is designed as active low gpio. So correcting the dt card detect gpio definition. Reviewed-by:
-
Lokesh Vutla authored
Use a single defconfig for all AM335x platforms by enabling FIT Signed-off-by:
-
Lokesh Vutla authored
Allow am335x-bone.dts to be built and enable uart and timer for all beaglebones. Reviewed-by:
-
Lokesh Vutla authored
FIT allows for a multiple dtb in a single image. SPL needs a way to detect the right dtb to be used. Adding support for the same. Signed-off-by:
-
Lokesh Vutla authored
Convert usb host boot defconfig to use DM, DT. Also enable FIT support. Reviewed-by:
-
Lokesh Vutla authored
Add initial DTS support for AM437x-IDK evm. Reviewed-by:
-
Lokesh Vutla authored
Add initial DTS support for AM43-EPOS evm. Reviewed-by:
-
Lokesh Vutla authored
Use a single defconfig for all AM43xx platforms by enabling FIT and delete the platform specific defconfigs. Signed-off-by:
-
Lokesh Vutla authored
FIT allows for a multiple dtb in a single image. SPL needs a way to detect the right dtb to be used. Adding support for the same. Reviewed-by:
-
Lokesh Vutla authored
Removing: uart3_defconfig: Now uart3 can be selected using menuconfig, removing separate config for uart mode. Doing uart boot is not straight forward as ROM uses uart3 as default serial console. In order to boot to prompt, concole in both u-boot and kernel needs to be changed. qspiboot_defconfig: The only advantage of enabling QSPI_BOOT is selecting env in QSPI. Eventually env needs to be selected by menuconfig so removing qspiboot_defconfig. qspiboot can be done using dra7xx_evm_defconfig. Reviewed-by:
-
Lokesh Vutla authored
Use a single defconfig for all DRA7 platforms by enabling FIT and delete the platform specific defconfigs. Signed-off-by:
-
Lokesh Vutla authored
FIT allows for a multiple dtb in a single image. SPL needs a way to detect the right dtb to be used. Adding support for the same. Reviewed-by:
-
Chris Packham authored
This follows on from commit d98b0523 ("powerpc: Cleanup BOOTFLAG_* references") and commit fc3d2976 ("Drop bogus BOOTFLAG_* definitions"). Remove the definitions that have crept in since. Signed-off-by:
Chris Packham <judge.packham@gmail.com>
-
Lokesh Vutla authored
This provides a way to load a FIT containing U-Boot and a selection of device tree files from UART. Reviewed-by:
-
Lokesh Vutla authored
No prints should be allowed during UART load. Reviewed-by:
-
Lokesh Vutla authored
Detect a FIT when loading from NAND and handle it using the new FIT SPL support. Reviewed-by:
-
Lokesh Vutla authored
When offset is not aligned to page address, it is possible that extra offset will be read from nand. Adjust the image such that first byte of the image is at load address after the first page is read. Reviewed-by:
-
Lokesh Vutla authored
Detect a FIT when loading from SPI and handle it using the new FIT SPL support. Reviewed-by:
-
Lokesh Vutla authored
Detect a FIT when loading from a FAT File system and handle it using the new FIT SPL support. Tested-by:
Michal Simek <michal.simek@xilinx.com> Reviewed-by:
Simon Glass <sjg@chromium.org> Reviewed-by:
-
Lokesh Vutla authored
This provides a way to load a FIT containing U-Boot and a selection of device tree files from a File system. Making sure that all the reads and writes are aligned to their respective needs. Tested-by:
-
Lokesh Vutla authored
sectors field is not being updated when reading fdt from fit image. Because of this size_of(u-boot.bin) is being read when reading fdt. Fixing it by updating the sectors field properly. Tested-by:
-
Daniel Allred authored
Adds new defconfig files for DRA7xx and AM57xx secure devices. These are the same as the non-secure parts, but with the addition of the CONFIG_TI_SECURE_DEVICE option set to 'y'. Signed-off-by:
Daniel Allred <d-allred@ti.com> Signed-off-by:
Madan Srinivas <madans@ti.com> Reviewed-by:
-
Daniel Allred authored
Adds the board specific ft_board_setup() functions that are called when CONFIG_OF_BOARD_SETUP is defined. These functions will currently just call the ft_cpu_setup() function. Adds CONFIG_OF_BOARD_SETUP to the defconfig files for dra72_evm, dra74_evm, and am57xx_evm. Signed-off-by:
-
Daniel Allred authored
Adds an fdt.c file in that defines the ft_cpu_setup() function, which should be called from a board-specific ft_board_setup()). This ft_cpu_setup() will currently do nothing for non-secure (GP) devices but contains pertinent updates for booting on secure (HS) devices. Update the omap5 Makefile to include the fdt.c in the build. Signed-off-by:
-
Daniel Allred authored
Update the CPU string output so that the device type is now included as part of the CPU string that is printed as the SPL or u-boot comes up. This update adds a suffix of the form "-GP" or "-HS" for production devices, so that general purpose (GP) and high security (HS) can be distiguished. Applies to all OMAP5 variants. Signed-off-by:
-
