The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399
platforms.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

pinctrl/rockchip.h provides defines that map pin numbers to pin names.
Use them to make the dts more human readable.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

This change updates the USB configuration for the RK3399-Q7 in the DTS:
 * fixes the OTG board configuration by enabling it ('okay')
 * improves the speed of 'usb start' by disabling the unused EHCI/OHCI
   controllers

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
 * the GPIO polarity is GPIO_ACTIVE_LOW
 * should be set to inactive (enable-active-low) when boot-on settings
   are applied
 * it can be changed at runtime (i.e. remove the always-on)

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.

This fixes the mix-up and models it correctly:
 * the GPIO is low-active
 * the regulator should be enabled (enable-active-high) during
   boot-on initialisation

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>

Renesas was spelled wrong.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>

Uniformize STMicroelectronics copyrights headers for SPEAR
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Uniformize STMicroelectronics copyrights headers for STV0991
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Uniformize STMicroelectronics copyrights headers for STM32
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Uniformize all STMicroelectronics copyrights headers for STi
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the
name of LDO17 is corrected to "vdd_ldo17".

Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

The API for get priv pointer is wrong, fix it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Add support for the latest MX6QP wandboard variant.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.

Brief description of implementation:
  Add two more address pointers (loadable_h, loadable_l) as arguments to
  sec_firmware_init() api.
  Create new api: sec_firmware_checks_copy_loadable() to check if loadables
  node is present in SEC firmware FIT image. If present, verify loadable
  image and copies it to secure DDR memory.
  Populate address pointers with secure DDR memory addresses where loadable
  is copied.

Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Use Kconfig to select QE-HDLC and USB pin-mux.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>

It will be reused in new DM LCD driver.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>

The supported sleep states are generic on Intel processors. Move the
ASL definition to the common place.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

On some platforms (eg: Braswell), the FSP will not produce the
graphics info HOB unless you plug some cables to the display
interface (eg: HDMI) on the board. Add such notes in the FSP
video driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Intel Braswell FSP requires SPI controller settings to be locked down,
let's do this in the chrryhill.dts and remove previous Kconfig option.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

This reverts commit 1e6ebee6.

It's not appropriate to call the Intel SPI driver specific stuff in
the FSP codes. We may add a simple DTS property "intel,spi-lock-down"
and let the Intel SPI driver call these stuff instead.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

In an S3 resume path, MRC cache is mandatory. Enforce the dependency
in the Kconfig.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Imply does not work for a Kconfig choice. Update ENV_IS_IN_SPI_FLASH
to be the default one for Intel Braswell.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

It was observed that when booting Linux kernel on Intel Cherry Hill
board, unexpected crash happens quite randomly. Sometimes kernel
just oops, while sometimes kernel throws MCE errors and hangs:

  mce: [Hardware Error]: Machine check events logged
  mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 4: c400000000010151
  mce: [Hardware Error]: TSC 0 ADDR 130f3f2c0
  mce: [Hardware Error]: PROCESSOR 0:406c3 TIME 1508160686 SOCKET 0 APIC 0 microcode 363

This looks like a hardware error per mcelog. After debugging, it
seems turning off turbo mode on the processor does not expose this
behavior, although U-Boot runs OK with turbo mode on. Suspect it is
related to an errata of Braswell processor.

To fix this, remove the Braswell cpu driver which does the turbo
mode configuration, and switch to use the generic cpu-x86 driver.
Also there is a configuration option in the FSP that turns on the
turbo mode and that has been turned off too.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.

Add code to setup simplefb for Allwinner DE2 driver.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.

Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The sunxi DE1 video option used to be CONFIG_VIDEO, which has the same
name as the "Enable legacy video support" option in
drivers/video/Kconfig.

Change the option name to CONFIG_VIDEO_SUNXI, which is really used by
Makefile under drivers/video/sunxi/, and defined in sunxi-common.h
when CONFIG_VIDEO is selected before this change. Now CONFIG_VIDEO_SUNXI
selects CONFIG_VIDEO and the usages of CONFIG_VIDEO in sunxi Kconfig and
config headers are all converted to use CONFIG_VIDEO_SUNXI.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

The U-Boot binary may trip over its actual allocated size in the storage.
In such a case, the environment will not be readable anymore (because
corrupted when the new image was flashed), and any attempt at using saveenv
to reconstruct the environment will result in a corrupted U-Boot binary.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

We start to get to the limit of our main U-Boot binary size (with some
boards even crossing it). Enable its build using thumb2 to get some extra
room.

Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a
wifi chip and some pin headers. Enable support for it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).

This results in a clock set to a frequency that isn't specified as
possible for CPUs.

Let's use the correct formula.

Fixes: f542948b ("sunxi: clk: add basic clocks for A83T")

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

Commit 06ad970b ("powerpc: mpc85xx: Implemente workaround for CPU
erratum A-007907") clears L1CSR2 for the boot core, but other cores
don't run through the workaround. Add similar code for secondary
cores to clear DCSTASHID field in L1CSR2 register.

Signed-off-by: York Sun <york.sun@nxp.com>

Commit dd74b945 ("ARM: uniphier: use pr_() instead of printf()
where appropriate"), but I missed to update this file for some reason.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL.  So, many nodes must
be marked as dm-pre-reloc to prevent fdtgrep from stripping them off.

Sprinkling U-Boot-specific properties all over the place is painful
because DT files are synced with Linux from time to time.

Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is
appended to UniPhier V7 DTS before the build.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

The option is never enabled by anyone.  Remove the code surrounded
by its ifdef.  This should be handled by the clock/reset drivers.

CONFIG_UNIPHIER_ETH in scripts/config_whitelist.txt will be dropped
by the next resync.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

This converts the following to Kconfig:
   CONFIG_NAND_MXC
   CONFIG_NAND_OMAP_GPMC
   CONFIG_NAND_OMAP_GPMC_PREFETCH
   CONFIG_NAND_OMAP_ELM
   CONFIG_SPL_NAND_AM33XX_BCH
   CONFIG_SPL_NAND_SIMPLE
   CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
        add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>

Azalia configuration may be different across boards, hence it's not
appropriate to do that in the SoC level. Instead, let's make the
SoC update_fsp_azalia_configs() routine as a weak version, and do
the actual work in the board codes.

So far it seems only som-db5800-som-6867 board enables the Azalia.
Move the original codes into som-db5800-som-6867.c.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>