T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
    T1040D4RDB is re-designed T1040RDB board with following changes :
    - Support of DDR4 memory
    - Support of 0x66 serdes protocol which can support following interfaces
        - 2 RGMII's on DTSEC4, DTSEC5
        - 1 SGMII on DTSEC3
    - Support of QE-TDM

    Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
    SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
    - Support of DDR4 memory
    - Support for 0x86 serdes protocol which can support following interfaces
        - 2 RGMII's on DTSEC4, DTSEC5
        - 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
    - Support of DIU

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

This board uses DDR DIMM. Reading SPD provides more flexibility.
Raw timing parameter code should be removed after debugging.

Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

A new interface is introduced to support generic board structure.
Converts it to use new interface.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

DDR-ODT require cfg_dram_type switch set properly as per DDR type.
T1040RDB, T1042RDB boards have DDR3L type DDR, so cfg_dram_type
should be set to OFF for DDR3L
Update t104xrdb/README for switch setting

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
      - Add spl.c which defines board_init_f, board_init_r
      - update tlb and ddr accordingly

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
 but on T104xRDB, on setting this , DDR instability is observed.
 Board-level debugging is in progress.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

T1040RDB is Freescale Reference Design Board supporting
the T1040 QorIQ Power Architecture™ processor.

 T1040RDB board Overview
 -----------------------
 - Four e5500 cores, each with a private 256 KB L2 cache
 - 256 KB shared L3 CoreNet platform cache (CPC)
 - Interconnect CoreNet platform
 - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
   support
 - Data Path Acceleration Architecture (DPAA) incorporating acceleration
 for the following functions:
    -  Packet parsing, classification, and distribution
    -  Queue management for scheduling, packet sequencing, and congestion
       management
    -  Cryptography Acceleration
    - RegEx Pattern Matching Acceleration
    - IEEE Std 1588 support
    - Hardware buffer management for buffer allocation and deallocation
 - Ethernet interfaces
    - Integrated 8-port Gigabit Ethernet switch
    - Four 1 Gbps Ethernet controllers
 - SERDES Connections, 8 lanes supporting:
    - PCI
    - SGMII
    - QSGMII
    - SATA 2.0
 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
   Interleaving
 -IFC/Local Bus
    - NAND flash: 1GB 8-bit NAND flash
    - NOR: 128MB 16-bit NOR Flash
 - Ethernet
    - Two on-board RGMII 10/100/1G ethernet ports.
    - PHY #0 remains powered up during deep-sleep
 - CPLD
 - Clocks
    - System and DDR clock (SYSCLK, “DDRCLK”)
    - SERDES clocks
 - Power Supplies
 - USB
    - Supports two USB 2.0 ports with integrated PHYs
    - Two type A ports with 5V@1.5A per port.
 - SDHC
    - SDHC/SDXC connector
 - SPI
    - On-board 64MB SPI flash
 - I2C
    - Devices connected: EEPROM, thermal monitor, VID controller
 - Other IO
    - Two Serial ports
    - ProfiBus port

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: fixed Makefile]
Acked-by: York Sun <yorksun@freescale.com>

T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.

 T1040QDS board Overview
 -----------------------
 - Four e5500 cores, each with a private 256 KB L2 cache
 - 256 KB shared L3 CoreNet platform cache (CPC)
 - Interconnect CoreNet platform
 - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
   support
 - Data Path Acceleration Architecture (DPAA) incorporating acceleration
 for the following functions:
    -  Packet parsing, classification, and distribution
    -  Queue management for scheduling, packet sequencing, and congestion
    	management
    -  Cryptography Acceleration
    - RegEx Pattern Matching Acceleration
    - IEEE Std 1588 support
    - Hardware buffer management for buffer allocation and deallocation
 - Ethernet interfaces
    - Integrated 8-port Gigabit Ethernet switch
    - Four 1 Gbps Ethernet controllers
 - SERDES Connections, 8 lanes supporting:
      — PCI Express: supporting Gen 1 and Gen 2;
      — SGMII
      — QSGMII
      — SATA 2.0
      — Aurora debug with dedicated connectors
 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
   Interleaving
 -IFC/Local Bus
     - NAND flash: 8-bit, async, up to 2GB.
     - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
     - GASIC: Simple (minimal) target within Qixis FPGA
     - PromJET rapid memory download support
 - Ethernet
     - Two on-board RGMII 10/100/1G ethernet ports.
     - PHY #0 remains powered up during deep-sleep
 - QIXIS System Logic FPGA
 - Clocks
     - System and DDR clock (SYSCLK, “DDRCLK”)
     - SERDES clocks
 - Power Supplies
 - Video
     - DIU supports video at up to 1280x1024x32bpp
 - USB
     - Supports two USB 2.0 ports with integrated PHYs
     — Two type A ports with 5V@1.5A per port.
     — Second port can be converted to OTG mini-AB
 - SDHC
     - SDHC port connects directly to an adapter card slot, featuring:
     - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
     — Supporting eMMC memory devices
 - SPI
    -  On-board support of 3 different devices and sizes
 - Other IO
    - Two Serial ports
    - ProfiBus port
    - Four I2C ports

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>

Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl

Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>

Add emulator support for T4240. Emulator has limited peripherals and
interfaces. Difference between emulator and T4240QDS includes:
	ECC for DDR is disabled due the procedure to load images
	No board FPGA (QIXIS)
	NOR flash has 32-bit port for higher loading speed
	IFC and I2C timing don't really matter, so set them fast
	No ethernet

Signed-off-by: York Sun <yorksun@freescale.com>

Update the timing table to support more rank density, based on the theory
that similar density DIMMs have similar clock adjust and write level start
timing. Update the timing for 1600 and 1866 MT/s. Tested with Micron
MT18JSF1G72AZ-1G9E1 DIMMs, iDIMM M3CN-4GMJ3C0C-M92.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.

SERDES Connections
  32 lanes grouped into four 8-lane banks
  Two “front side” banks dedicated to Ethernet
  Two “back side” banks dedicated to other protocols
DDR Controllers
  Three independant 64-bit DDR3 controllers
  Supports rates up to 2133 MHz data-rate
  Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA

Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.

Detail information can be found in doc/README.t4qds

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>