The mutex lock and unlock functions are stubbed out and mutex_is_locked
was 0.  This caused asserts to fail in ubifs code when checking that the
mutex was locked.  For example,

UBIFS assert failed in ubifs_change_lp at 540
UBIFS assert failed in ubifs_release_lprops at 278

Assume that the "mutex" is locked since that is the normal case when it
is checked in the ubifs code.

Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>

Xilinx changes for v2018.05-rc2

- Various DT changes and sync with mainline kernel
- Various defconfig updates
- Add SPL init for zcu102 revA
- Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX
  and zc1751-dc3
- Net fixes - xlnx,phy-type
- 64bit axi ethernet support
- arasan: Fix nand write issue
- fpga fixes
- Maintainer file updates

Patch queue for efi - 2018-04-09

Highlights this time around:

  - Lots of minor spec compliance fixes
  - Support full range of GOP BLT commands
  - More fine grained error checking
  - Network fixes (init, DP)
  - Lots of other bug fixes...

Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Xilinx zcu104 is another customer board. It is sort of zcu102 clone with
some differences.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

zc1751 is based board with dc3 extenstion card which is used for silicon
validation.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add support for Xilinx zcu100.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

SPL MMC boot requires to have clock early.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.

Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>

This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.

Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>

Add psu init for zc1751 dc cards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add psu init for zcu102-revA.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch enables the fixed link support for
all ZynqMP boards.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There is no memory which stores mac address that's why generate it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable ethernet phys for zc1751 dc5.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.

To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Targets without net can't use pxe or dhcp boot methods.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch reads phytype from property "xlnx,phy-type" instead
od simply looking for "phy-type". This is to be inline with
Linux and also fixes the issue of detecting it wrongly in
u-boot.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This patch uses writeq() function to enable greater than 32 bit
addressing of axi-ethernet for the ZynqMP devices.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

In commit 2453c695 ("arm64: zynqmp: nand: Fixed NAND erase issue for
size 1GiB or more"), ARASAN_NAND_MEM_ADDR1_PAGE_MASK macro changed
to 0xFFFF and the same macro is used in nand write and so that getting
nand write error.
This patch reverted this macro to the 0xFFFF0000 and used
ARASAN_NAND_MEM_ADDR1_COL_MASK in the nand erase function
which is equal to 0xFFFF.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There is delay needed after PCFG_PROGB change if
AES key source is efuse. This fixes the issue of
encrypted bitstream loading with AES efuse as key
source.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Xilfpga library expects the size of bitstream in a pointer
but currenly we are passing the size as a value. This patch
fixes this issue.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Latest xilfpga expects to set BIT5 of flags for nonsecure
bitsream and also expects length in bytes instead of words
This patch does the same.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>

This patch adds support for ZynqMP platform to print FPGA PCAP status
for "fpga status" command.

Signed-off-by: Nitin Jain <nitinj@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

New and old clk drivers are sharing IDs and descriptions.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Sync with mainline.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

- Use eeprom for node name
- Use atmel compatible string instead of at.
- Add missing labels

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.

But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.

So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

i2c muxes should described like this.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Use different location for SPDX line. Also update dates for new mainline
DTS files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The patch fixing issues reported by DTC:
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0x400000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0x800000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xc00000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xd00000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xf00000 unit name should not have
leading "0x"

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There is no reason to have double spaces for indentation.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add vendor prefix to si5341.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

There shouldn't be a number appended based on spec.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

U-Boot commands shouldn't be the part of kernel DTS files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This patch adds no-1-8-v below properties to sd node for dc5 board dts.

Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Enable TTCs for this target as is done in Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

eeprom can contain information which can be used by nvmem drivers.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>