Signed-off-by: Wolfgang Denk <wd@denx.de>

Fixed typo in ne2000.h, thinko re n2k_inb() usage, don't try
to do anything in eth_stop() if eth_init() was not called.
Simplified RX path in order to avoid timeouts on really really
fast NE2000 cards (read: qemu with internal tftp), NetLoop() is
clever enough to cope with 1 packet per eth_rx().

Signed-off-by: Vlad Lungu <vlad@comsys.ro>

Signed-off-by: Detlev Zundel <dzu@denx.de>

Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into
Makfile and MAKEALL

Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Correct to val8 from val.

Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Runet Torgersen <runet@innovsys.com>

As a direct correlation exists between DDR DIMM slots
and SPD EEPROM addresses used to configure them, use
the individually defined SPD_EEPROM_ADDRESS* values to
determine if a DDR DIMM slot should have its SPD
configuration read or not.

Effectively, this now allows for 1 or 2 DIMM slots
per memory controller.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Some USB keys need to be switched off before loading the kernel
otherwise they can remain in an undefined status which prevents them
to be correctly recognized by the kernel.

Signed-off-by: Rodolfo Giometti <giometti@linux.it>

The I2C bootstrap values that can be setup via the "bootstrap" command,
were setup incorrect regarding the generation of the internal sync PCI
clock. The values for PLB clock == 133MHz were slighly incorrect and the
values for PLB clock == 166MHz were totally incorrect. This could
lead to a hangup upon booting while PCI configuration scan.

This patch fixes this issue and configures valid PCI divisor values
for the sync PCI clock, with respect to the provided external async
PCI frequency.

Here the values of the formula in the chapter 14.2 "PCI clocking"
from the 440EPx users manual:

AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz

33MHz async PCI frequency:
PLB = 133:
=>      32 <= 44.3 <= 65        (div = 3)

PLB = 166:
=>      32 <= 55.3 <= 65        (div = 3)

66MHz async PCI frequency:
PLB = 133:
=>      65 <= 66.5 <= 132       (div = 2)

PLB = 166:
=>      65 <= 83 <= 132         (div = 2)

Signed-off-by: Stefan Roese <sr@denx.de>

The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.

This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.

Signed-off-by: Stefan Roese <sr@denx.de>

Adjust flash map to support the new S29GLxxN (N-Type) Flashes with
doubled sector size.

Signed-off-by: Martin Krause <martin.krause@tqs.de>

Signed-off-by: Martin Krause <martin.krause@tqs.de>

At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 97. This result
in a refresh rate of 4 * 7.8 us at the default clock
50 MHz. At 133 MHz the value will be then 4 * 2.9 us.
This is a compromise until a new method is found to
adjust the refresh rate.

Signed-off-by: Martin Krause <martin.krause@tqs.de>

Adjust flash map to support the new S29GLxxN (N-Type) Flashes with
doubled sector size.

Signed-off-by: Martin Krause <martin.krause@tqs.de>

and remove code violation

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>