armv8: ls1043ardb: Use static DDR setting for SPL boot

This board has soldered DDR chips. To reduce the SPL image size,
use static DDR setting instead of dynamic DDR driver.

Signed-off-by: York Sun <york.sun@nxp.com>

board/freescale/ls1043ardb/ddr.c

@@ -169,17 +169,63 @@ int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
 
 	return 0;
 }
+#else
+
+phys_size_t fixed_sdram(void)
+{
+	int i;
+	char buf[32];
+	fsl_ddr_cfg_regs_t ddr_cfg_regs;
+	phys_size_t ddr_size;
+	ulong ddr_freq, ddr_freq_mhz;
+
+	ddr_freq = get_ddr_freq(0);
+	ddr_freq_mhz = ddr_freq / 1000000;
+
+	printf("Configuring DDR for %s MT/s data rate\n",
+	       strmhz(buf, ddr_freq));
+
+	for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
+		if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
+		    (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
+			memcpy(&ddr_cfg_regs,
+			       fixed_ddr_parm_0[i].ddr_settings,
+			       sizeof(ddr_cfg_regs));
+			break;
+		}
+	}
+
+	if (fixed_ddr_parm_0[i].max_freq == 0)
+		panic("Unsupported DDR data rate %s MT/s data rate\n",
+		      strmhz(buf, ddr_freq));
+
+	ddr_size = (phys_size_t)2048 * 1024 * 1024;
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0);
+
+	return ddr_size;
+}
 #endif
 
 int fsl_initdram(void)
 {
 	phys_size_t dram_size;
 
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
 	puts("Initializing DDR....\n");
 	dram_size = fsl_ddr_sdram();
 #else
 	dram_size =  fsl_ddr_sdram_size();
+#endif
+#else
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
+	puts("Initialzing DDR using fixed setting\n");
+	dram_size = fixed_sdram();
+#else
+	gd->ram_size = 0x80000000;
+
+	return 0;
+#endif
 #endif
 	erratum_a008850_post();
 

board/freescale/ls1043ardb/ddr.h

@@ -45,4 +45,73 @@ static const struct board_specific_parameters *udimms[] = {
 	udimm0,
 };
 
+#ifndef CONFIG_SYS_DDR_RAW_TIMING
+fsl_ddr_cfg_regs_t ddr_cfg_regs_1600 = {
+	.cs[0].bnds = 0x0000007F,
+	.cs[1].bnds = 0,
+	.cs[2].bnds = 0,
+	.cs[3].bnds = 0,
+	.cs[0].config = 0x80040322,
+	.cs[0].config_2 = 0,
+	.cs[1].config = 0,
+	.cs[1].config_2 = 0,
+	.cs[2].config = 0,
+	.cs[3].config = 0,
+	.timing_cfg_3 = 0x010C1000,
+	.timing_cfg_0 = 0x91550018,
+	.timing_cfg_1 = 0xBBB48C42,
+	.timing_cfg_2 = 0x0048C111,
+	.ddr_sdram_cfg = 0xC50C0008,
+	.ddr_sdram_cfg_2 = 0x00401100,
+	.ddr_sdram_cfg_3 = 0,
+	.ddr_sdram_mode = 0x03010210,
+	.ddr_sdram_mode_2 = 0,
+	.ddr_sdram_mode_3 = 0x00010210,
+	.ddr_sdram_mode_4 = 0,
+	.ddr_sdram_mode_5 = 0x00010210,
+	.ddr_sdram_mode_6 = 0,
+	.ddr_sdram_mode_7 = 0x00010210,
+	.ddr_sdram_mode_8 = 0,
+	.ddr_sdram_mode_9 = 0x00000500,
+	.ddr_sdram_mode_10 = 0x04000000,
+	.ddr_sdram_mode_11 = 0x00000400,
+	.ddr_sdram_mode_12 = 0x04000000,
+	.ddr_sdram_mode_13 = 0x00000400,
+	.ddr_sdram_mode_14 = 0x04000000,
+	.ddr_sdram_mode_15 = 0x00000400,
+	.ddr_sdram_mode_16 = 0x04000000,
+	.ddr_sdram_interval = 0x18600618,
+	.ddr_data_init = 0xDEADBEEF,
+	.ddr_sdram_clk_cntl = 0x03000000,
+	.ddr_init_addr = 0,
+	.ddr_init_ext_addr = 0,
+	.timing_cfg_4 = 0x00000002,
+	.timing_cfg_5 = 0x03401400,
+	.timing_cfg_6 = 0,
+	.timing_cfg_7 = 0x13300000,
+	.timing_cfg_8 = 0x02115600,
+	.timing_cfg_9 = 0,
+	.ddr_zq_cntl = 0x8A090705,
+	.ddr_wrlvl_cntl = 0x8675F607,
+	.ddr_wrlvl_cntl_2 = 0x07090800,
+	.ddr_wrlvl_cntl_3 = 0,
+	.ddr_sr_cntr = 0,
+	.ddr_sdram_rcw_1 = 0,
+	.ddr_sdram_rcw_2 = 0,
+	.ddr_cdr1 = 0x80040000,
+	.ddr_cdr2 = 0x0000A181,
+	.dq_map_0 = 0,
+	.dq_map_1 = 0,
+	.dq_map_2 = 0,
+	.dq_map_3 = 0,
+	.debug[28] = 0x00700046,
+
+};
+
+fixed_ddr_parm_t fixed_ddr_parm_0[] = {
+	{1550, 1650, &ddr_cfg_regs_1600},
+	{0, 0, NULL}
+};
+
+#endif
 #endif

include/configs/ls1043ardb.h

@@ -28,13 +28,13 @@
 
 #define CONFIG_SYS_SPD_BUS_NUM		0
 
-#define CONFIG_FSL_DDR_BIST
 #ifndef CONFIG_SPL
-#define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
-#endif
 #define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
+#define CONFIG_FSL_DDR_BIST
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
+#endif
 
 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1043ardb/ls1043ardb_pbi.cfg