arm64: ls1046a: Add sata distro boot support

Sata is equipped on ls1046a and can be a boot source. Add sata boot
support as an option if available.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

include/configs/ls1046a_common.h

@@ -145,6 +145,18 @@
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 
+/* SATA */
+#ifndef SPL_NO_SATA
+#define CONFIG_SCSI_AHCI_PLAT
+
+#define CONFIG_SYS_SATA				AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
+#define CONFIG_SYS_SCSI_MAX_LUN			1
+#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+						CONFIG_SYS_SCSI_MAX_LUN)
+#endif
+
 /* Command line configuration */
 
 /* MMC */
@@ -197,6 +209,7 @@
 #include <config_distro_defaults.h>
 #ifndef CONFIG_SPL_BUILD
 #define BOOT_TARGET_DEVICES(func) \
+	func(SCSI, scsi, 0) \
 	func(MMC, mmc, 0) \
 	func(USB, usb, 0)
 #include <config_distro_bootcmd.h>

include/configs/ls1046aqds.h

@@ -136,9 +136,6 @@ unsigned long get_board_ddr_clk(void);
 #define CFG_LPUART_EN		0x2
 #endif
 
-/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
-
 /* EEPROM */
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
@@ -148,13 +145,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
 
-#define CONFIG_SYS_SATA				AHCI_BASE_ADDR
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
-#define CONFIG_SYS_SCSI_MAX_LUN			1
-#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-						CONFIG_SYS_SCSI_MAX_LUN)
-
 /*
  * IFC Definitions
  */

include/configs/ls1046ardb.h

@@ -211,18 +211,6 @@
 #endif
 #endif
 
-/* SATA */
-#ifndef SPL_NO_SATA
-#define CONFIG_SCSI_AHCI_PLAT
-
-#define CONFIG_SYS_SATA				AHCI_BASE_ADDR
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
-#define CONFIG_SYS_SCSI_MAX_LUN			1
-#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-						CONFIG_SYS_SCSI_MAX_LUN)
-#endif
-
 #ifndef SPL_NO_MISC
 #undef CONFIG_BOOTCOMMAND
 #if defined(CONFIG_QSPI_BOOT)