ARMv7M: Add STM32F4 support

Signed-off-by: Kamil Lulko <rev13@wp.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>

arch/arm/cpu/armv7m/Makefile

@@ -7,3 +7,5 @@
 
 extra-y := start.o
 obj-y += cpu.o
+
+obj-$(CONFIG_STM32F4) += stm32f4/

arch/arm/cpu/armv7m/stm32f4/Makefile

+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2015
+# Kamil Lulko, <rev13@wp.pl>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += soc.o clock.o timer.o flash.o

arch/arm/cpu/armv7m/stm32f4/clock.c

+/*
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * (C) Copyright 2014
+ * STMicroelectronics
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/stm32.h>
+
+#define RCC_CR_HSION		(1 << 0)
+#define RCC_CR_HSEON		(1 << 16)
+#define RCC_CR_HSERDY		(1 << 17)
+#define RCC_CR_HSEBYP		(1 << 18)
+#define RCC_CR_CSSON		(1 << 19)
+#define RCC_CR_PLLON		(1 << 24)
+#define RCC_CR_PLLRDY		(1 << 25)
+
+#define RCC_PLLCFGR_PLLM_MASK	0x3F
+#define RCC_PLLCFGR_PLLN_MASK	0x7FC0
+#define RCC_PLLCFGR_PLLP_MASK	0x30000
+#define RCC_PLLCFGR_PLLQ_MASK	0xF000000
+#define RCC_PLLCFGR_PLLSRC	(1 << 22)
+#define RCC_PLLCFGR_PLLN_SHIFT	6
+#define RCC_PLLCFGR_PLLP_SHIFT	16
+#define RCC_PLLCFGR_PLLQ_SHIFT	24
+
+#define RCC_CFGR_AHB_PSC_MASK	0xF0
+#define RCC_CFGR_APB1_PSC_MASK	0x1C00
+#define RCC_CFGR_APB2_PSC_MASK	0xE000
+#define RCC_CFGR_SW0		(1 << 0)
+#define RCC_CFGR_SW1		(1 << 1)
+#define RCC_CFGR_SW_MASK	0x3
+#define RCC_CFGR_SW_HSI		0
+#define RCC_CFGR_SW_HSE		RCC_CFGR_SW0
+#define RCC_CFGR_SW_PLL		RCC_CFGR_SW1
+#define RCC_CFGR_SWS0		(1 << 2)
+#define RCC_CFGR_SWS1		(1 << 3)
+#define RCC_CFGR_SWS_MASK	0xC
+#define RCC_CFGR_SWS_HSI	0
+#define RCC_CFGR_SWS_HSE	RCC_CFGR_SWS0
+#define RCC_CFGR_SWS_PLL	RCC_CFGR_SWS1
+#define RCC_CFGR_HPRE_SHIFT	4
+#define RCC_CFGR_PPRE1_SHIFT	10
+#define RCC_CFGR_PPRE2_SHIFT	13
+
+#define RCC_APB1ENR_PWREN	(1 << 28)
+
+#define PWR_CR_VOS0		(1 << 14)
+#define PWR_CR_VOS1		(1 << 15)
+#define PWR_CR_VOS_MASK		0xC000
+#define PWR_CR_VOS_SCALE_MODE_1	(PWR_CR_VOS0 | PWR_CR_VOS1)
+#define PWR_CR_VOS_SCALE_MODE_2	(PWR_CR_VOS1)
+#define PWR_CR_VOS_SCALE_MODE_3	(PWR_CR_VOS0)
+
+#define FLASH_ACR_WS(n)		n
+#define FLASH_ACR_PRFTEN	(1 << 8)
+#define FLASH_ACR_ICEN		(1 << 9)
+#define FLASH_ACR_DCEN		(1 << 10)
+
+struct pll_psc {
+	u8	pll_m;
+	u16	pll_n;
+	u8	pll_p;
+	u8	pll_q;
+	u8	ahb_psc;
+	u8	apb1_psc;
+	u8	apb2_psc;
+};
+
+#define AHB_PSC_1		0
+#define AHB_PSC_2		0x8
+#define AHB_PSC_4		0x9
+#define AHB_PSC_8		0xA
+#define AHB_PSC_16		0xB
+#define AHB_PSC_64		0xC
+#define AHB_PSC_128		0xD
+#define AHB_PSC_256		0xE
+#define AHB_PSC_512		0xF
+
+#define APB_PSC_1		0
+#define APB_PSC_2		0x4
+#define APB_PSC_4		0x5
+#define APB_PSC_8		0x6
+#define APB_PSC_16		0x7
+
+#if !defined(CONFIG_STM32_HSE_HZ)
+#error "CONFIG_STM32_HSE_HZ not defined!"
+#else
+#if (CONFIG_STM32_HSE_HZ == 8000000)
+struct pll_psc pll_psc_168 = {
+	.pll_m = 8,
+	.pll_n = 336,
+	.pll_p = 2,
+	.pll_q = 7,
+	.ahb_psc = AHB_PSC_1,
+	.apb1_psc = APB_PSC_4,
+	.apb2_psc = APB_PSC_2
+};
+#else
+#error "No PLL/Prescaler configuration for given CONFIG_STM32_HSE_HZ exists"
+#endif
+#endif
+
+int configure_clocks(void)
+{
+	/* Reset RCC configuration */
+	setbits_le32(&STM32_RCC->cr, RCC_CR_HSION);
+	writel(0, &STM32_RCC->cfgr); /* Reset CFGR */
+	clrbits_le32(&STM32_RCC->cr, (RCC_CR_HSEON | RCC_CR_CSSON
+		| RCC_CR_PLLON));
+	writel(0x24003010, &STM32_RCC->pllcfgr); /* Reset value from RM */
+	clrbits_le32(&STM32_RCC->cr, RCC_CR_HSEBYP);
+	writel(0, &STM32_RCC->cir); /* Disable all interrupts */
+
+	/* Configure for HSE+PLL operation */
+	setbits_le32(&STM32_RCC->cr, RCC_CR_HSEON);
+	while (!(readl(&STM32_RCC->cr) & RCC_CR_HSERDY))
+		;
+
+	/* Enable high performance mode, System frequency up to 168 MHz */
+	setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_PWREN);
+	writel(PWR_CR_VOS_SCALE_MODE_1, &STM32_PWR->cr);
+
+	setbits_le32(&STM32_RCC->cfgr, ((
+		pll_psc_168.ahb_psc << RCC_CFGR_HPRE_SHIFT)
+		| (pll_psc_168.apb1_psc << RCC_CFGR_PPRE1_SHIFT)
+		| (pll_psc_168.apb2_psc << RCC_CFGR_PPRE2_SHIFT)));
+
+	writel(pll_psc_168.pll_m
+		| (pll_psc_168.pll_n << RCC_PLLCFGR_PLLN_SHIFT)
+		| (((pll_psc_168.pll_p >> 1) - 1) << RCC_PLLCFGR_PLLP_SHIFT)
+		| (pll_psc_168.pll_q << RCC_PLLCFGR_PLLQ_SHIFT),
+		&STM32_RCC->pllcfgr);
+	setbits_le32(&STM32_RCC->pllcfgr, RCC_PLLCFGR_PLLSRC);
+
+	setbits_le32(&STM32_RCC->cr, RCC_CR_PLLON);
+
+	while (!(readl(&STM32_RCC->cr) & RCC_CR_PLLRDY))
+		;
+
+	/* 5 wait states, Prefetch enabled, D-Cache enabled, I-Cache enabled */
+	writel(FLASH_ACR_WS(5) | FLASH_ACR_PRFTEN | FLASH_ACR_ICEN
+		| FLASH_ACR_DCEN, &STM32_FLASH->acr);
+
+	clrbits_le32(&STM32_RCC->cfgr, (RCC_CFGR_SW0 | RCC_CFGR_SW1));
+	setbits_le32(&STM32_RCC->cfgr, RCC_CFGR_SW_PLL);
+
+	while ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) !=
+			RCC_CFGR_SWS_PLL)
+		;
+
+	return 0;
+}
+
+unsigned long clock_get(enum clock clck)
+{
+	u32 sysclk = 0;
+	u32 shift = 0;
+	/* Prescaler table lookups for clock computation */
+	u8 ahb_psc_table[16] = {
+		0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9
+	};
+	u8 apb_psc_table[8] = {
+		0, 0, 0, 0, 1, 2, 3, 4
+	};
+
+	if ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) ==
+			RCC_CFGR_SWS_PLL) {
+		u16 pllm, plln, pllp;
+		pllm = (readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLM_MASK);
+		plln = ((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLN_MASK)
+			>> RCC_PLLCFGR_PLLN_SHIFT);
+		pllp = ((((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLP_MASK)
+			>> RCC_PLLCFGR_PLLP_SHIFT) + 1) << 1);
+		sysclk = ((CONFIG_STM32_HSE_HZ / pllm) * plln) / pllp;
+	}
+
+	switch (clck) {
+	case CLOCK_CORE:
+		return sysclk;
+		break;
+	case CLOCK_AHB:
+		shift = ahb_psc_table[(
+			(readl(&STM32_RCC->cfgr) & RCC_CFGR_AHB_PSC_MASK)
+			>> RCC_CFGR_HPRE_SHIFT)];
+		return sysclk >>= shift;
+		break;
+	case CLOCK_APB1:
+		shift = apb_psc_table[(
+			(readl(&STM32_RCC->cfgr) & RCC_CFGR_APB1_PSC_MASK)
+			>> RCC_CFGR_PPRE1_SHIFT)];
+		return sysclk >>= shift;
+		break;
+	case CLOCK_APB2:
+		shift = apb_psc_table[(
+			(readl(&STM32_RCC->cfgr) & RCC_CFGR_APB2_PSC_MASK)
+			>> RCC_CFGR_PPRE2_SHIFT)];
+		return sysclk >>= shift;
+		break;
+	default:
+		return 0;
+		break;
+	}
+}

arch/arm/cpu/armv7m/stm32f4/flash.c

+/*
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/stm32.h>
+
+#define STM32_FLASH_KEY1	0x45670123
+#define STM32_FLASH_KEY2	0xCDEF89AB
+
+flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
+
+const u32 sect_sz_kb[CONFIG_SYS_MAX_FLASH_SECT] = {
+	[0 ... 3] =	16 * 1024,
+	[4] =		64 * 1024,
+	[5 ... 11] =	128 * 1024
+};
+
+static void stm32f4_flash_lock(u8 lock)
+{
+	if (lock) {
+		setbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_LOCK);
+	} else {
+		writel(STM32_FLASH_KEY1, &STM32_FLASH->key);
+		writel(STM32_FLASH_KEY2, &STM32_FLASH->key);
+	}
+}
+
+unsigned long flash_init(void)
+{
+	unsigned long total_size = 0;
+	u8 i, j;
+
+	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
+		flash_info[i].flash_id = FLASH_STM32F4;
+		flash_info[i].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
+		flash_info[i].start[0] = CONFIG_SYS_FLASH_BASE + (i << 20);
+		flash_info[i].size = sect_sz_kb[0];
+		for (j = 1; j < CONFIG_SYS_MAX_FLASH_SECT; j++) {
+			flash_info[i].start[j] = flash_info[i].start[j - 1]
+				+ (sect_sz_kb[j - 1]);
+			flash_info[i].size += sect_sz_kb[j];
+		}
+		total_size += flash_info[i].size;
+	}
+
+	return total_size;
+}
+
+void flash_print_info(flash_info_t *info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf("missing or unknown FLASH type\n");
+		return;
+	} else if (info->flash_id == FLASH_STM32F4) {
+		printf("STM32F4 Embedded Flash\n");
+	}
+
+	printf("  Size: %ld MB in %d Sectors\n",
+	       info->size >> 20, info->sector_count);
+
+	printf("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf("\n   ");
+		printf(" %08lX%s",
+		       info->start[i],
+			info->protect[i] ? " (RO)" : "     ");
+	}
+	printf("\n");
+	return;
+}
+
+int flash_erase(flash_info_t *info, int first, int last)
+{
+	u8 bank = 0xFF;
+	int i;
+
+	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
+		if (info == &flash_info[i]) {
+			bank = i;
+			break;
+		}
+	}
+	if (bank == 0xFF)
+		return -1;
+
+	stm32f4_flash_lock(0);
+
+	for (i = first; i <= last; i++) {
+		while (readl(&STM32_FLASH->sr) & STM32_FLASH_SR_BSY)
+			;
+
+		if (bank == 0) {
+			setbits_le32(&STM32_FLASH->cr,
+				     (i << STM32_FLASH_CR_SNB_OFFSET));
+		} else if (bank == 1) {
+			setbits_le32(&STM32_FLASH->cr,
+				     ((0x10 | i) << STM32_FLASH_CR_SNB_OFFSET));
+		} else {
+			stm32f4_flash_lock(1);
+			return -1;
+		}
+		setbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_SER);
+		setbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_STRT);
+
+		while (readl(&STM32_FLASH->sr) & STM32_FLASH_SR_BSY)
+			;
+
+		clrbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_SER);
+		stm32f4_flash_lock(1);
+	}
+
+	return 0;
+}
+
+int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	ulong i;
+
+	while (readl(&STM32_FLASH->sr) & STM32_FLASH_SR_BSY)
+		;
+
+	stm32f4_flash_lock(0);
+
+	setbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_PG);
+	/* To make things simple use byte writes only */
+	for (i = 0; i < cnt; i++) {
+		*(uchar *)(addr + i) = src[i];
+		while (readl(&STM32_FLASH->sr) & STM32_FLASH_SR_BSY)
+			;
+	}
+	clrbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_PG);
+	stm32f4_flash_lock(1);
+
+	return 0;
+}

arch/arm/cpu/armv7m/stm32f4/soc.c

+/*
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/armv7m.h>
+#include <asm/arch/stm32.h>
+
+u32 get_cpu_rev(void)
+{
+	return 0;
+}
+
+int arch_cpu_init(void)
+{
+	configure_clocks();
+
+	/*
+	 * Configure the memory protection unit (MPU) to allow full access to
+	 * the whole 4GB address space.
+	 */
+	writel(0, &V7M_MPU->rnr);
+	writel(0, &V7M_MPU->rbar);
+	writel((V7M_MPU_RASR_AP_RW_RW | V7M_MPU_RASR_SIZE_4GB
+		| V7M_MPU_RASR_EN), &V7M_MPU->rasr);
+	writel(V7M_MPU_CTRL_ENABLE | V7M_MPU_CTRL_HFNMIENA, &V7M_MPU->ctrl);
+
+	return 0;
+}
+
+void s_init(void)
+{
+}

arch/arm/cpu/armv7m/stm32f4/timer.c

+/*
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/armv7m.h>
+#include <asm/arch/stm32.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define STM32_TIM2_BASE	(STM32_APB1PERIPH_BASE + 0x0000)
+
+#define RCC_APB1ENR_TIM2EN	(1 << 0)
+
+struct stm32_tim2_5 {
+	u32 cr1;
+	u32 cr2;
+	u32 smcr;
+	u32 dier;
+	u32 sr;
+	u32 egr;
+	u32 ccmr1;
+	u32 ccmr2;
+	u32 ccer;
+	u32 cnt;
+	u32 psc;
+	u32 arr;
+	u32 reserved1;
+	u32 ccr1;
+	u32 ccr2;
+	u32 ccr3;
+	u32 ccr4;
+	u32 reserved2;
+	u32 dcr;
+	u32 dmar;
+	u32 or;
+};
+
+#define TIM_CR1_CEN	(1 << 0)
+
+#define TIM_EGR_UG	(1 << 0)
+
+int timer_init(void)
+{
+	struct stm32_tim2_5 *tim = (struct stm32_tim2_5 *)STM32_TIM2_BASE;
+
+	setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
+
+	if (clock_get(CLOCK_AHB) == clock_get(CLOCK_APB1))
+		writel((clock_get(CLOCK_APB1) / CONFIG_SYS_HZ_CLOCK) - 1,
+		       &tim->psc);
+	else
+		writel(((clock_get(CLOCK_APB1) * 2) / CONFIG_SYS_HZ_CLOCK) - 1,
+		       &tim->psc);
+
+	writel(0xFFFFFFFF, &tim->arr);
+	writel(TIM_CR1_CEN, &tim->cr1);
+	setbits_le32(&tim->egr, TIM_EGR_UG);
+
+	gd->arch.tbl = 0;
+	gd->arch.tbu = 0;
+	gd->arch.lastinc = 0;
+
+	return 0;
+}
+
+ulong get_timer(ulong base)
+{
+	return (get_ticks() / (CONFIG_SYS_HZ_CLOCK / CONFIG_SYS_HZ)) - base;
+}
+
+unsigned long long get_ticks(void)
+{
+	struct stm32_tim2_5 *tim = (struct stm32_tim2_5 *)STM32_TIM2_BASE;
+	u32 now;
+
+	now = readl(&tim->cnt);
+
+	if (now >= gd->arch.lastinc)
+		gd->arch.tbl += (now - gd->arch.lastinc);
+	else
+		gd->arch.tbl += (0xFFFFFFFF - gd->arch.lastinc) + now;
+
+	gd->arch.lastinc = now;
+
+	return gd->arch.tbl;
+}
+
+void reset_timer(void)
+{
+	struct stm32_tim2_5 *tim = (struct stm32_tim2_5 *)STM32_TIM2_BASE;
+
+	gd->arch.lastinc = readl(&tim->cnt);
+	gd->arch.tbl = 0;
+}
+
+/* delay x useconds */
+void __udelay(ulong usec)
+{
+	unsigned long long start;
+
+	start = get_ticks();		/* get current timestamp */
+	while ((get_ticks() - start) < usec)
+		;			/* loop till time has passed */
+}
+
+/*
+ * This function is derived from PowerPC code (timebase clock frequency).
+ * On ARM it returns the number of timer ticks per second.
+ */
+ulong get_tbclk(void)
+{
+	return CONFIG_SYS_HZ_CLOCK;
+}

arch/arm/include/asm/arch-stm32f4/fmc.h

+/*
+ * (C) Copyright 2013
+ * Pavel Boldin, Emcraft Systems, paboldin@emcraft.com
+ *
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _MACH_FMC_H_
+#define _MACH_FMC_H_
+
+struct stm32_fmc_regs {
+	u32 sdcr1;	/* Control register 1 */
+	u32 sdcr2;	/* Control register 2 */
+	u32 sdtr1;	/* Timing register 1 */
+	u32 sdtr2;	/* Timing register 2 */
+	u32 sdcmr;	/* Mode register */
+	u32 sdrtr;	/* Refresh timing register */
+	u32 sdsr;	/* Status register */
+};
+
+/*
+ * FMC registers base
+ */
+#define STM32_SDRAM_FMC_BASE	0xA0000140
+#define STM32_SDRAM_FMC		((struct stm32_fmc_regs *)STM32_SDRAM_FMC_BASE)
+
+/* Control register SDCR */
+#define FMC_SDCR_RPIPE_SHIFT	13	/* RPIPE bit shift */
+#define FMC_SDCR_RBURST_SHIFT	12	/* RBURST bit shift */
+#define FMC_SDCR_SDCLK_SHIFT	10	/* SDRAM clock divisor shift */
+#define FMC_SDCR_WP_SHIFT	9	/* Write protection shift */
+#define FMC_SDCR_CAS_SHIFT	7	/* CAS latency shift */
+#define FMC_SDCR_NB_SHIFT	6	/* Number of banks shift */
+#define FMC_SDCR_MWID_SHIFT	4	/* Memory width shift */
+#define FMC_SDCR_NR_SHIFT	2	/* Number of row address bits shift */
+#define FMC_SDCR_NC_SHIFT	0	/* Number of col address bits shift */
+
+/* Timings register SDTR */
+#define FMC_SDTR_TMRD_SHIFT	0	/* Load mode register to active */
+#define FMC_SDTR_TXSR_SHIFT	4	/* Exit self-refresh time */
+#define FMC_SDTR_TRAS_SHIFT	8	/* Self-refresh time */
+#define FMC_SDTR_TRC_SHIFT	12	/* Row cycle delay */
+#define FMC_SDTR_TWR_SHIFT	16	/* Recovery delay */
+#define FMC_SDTR_TRP_SHIFT	20	/* Row precharge delay */
+#define FMC_SDTR_TRCD_SHIFT	24	/* Row-to-column delay */
+
+
+#define FMC_SDCMR_NRFS_SHIFT	5
+
+#define FMC_SDCMR_MODE_NORMAL		0
+#define FMC_SDCMR_MODE_START_CLOCK	1
+#define FMC_SDCMR_MODE_PRECHARGE	2
+#define FMC_SDCMR_MODE_AUTOREFRESH	3
+#define FMC_SDCMR_MODE_WRITE_MODE	4
+#define FMC_SDCMR_MODE_SELFREFRESH	5
+#define FMC_SDCMR_MODE_POWERDOWN	6
+
+#define FMC_SDCMR_BANK_1		(1 << 4)
+#define FMC_SDCMR_BANK_2		(1 << 3)
+
+#define FMC_SDCMR_MODE_REGISTER_SHIFT	9
+
+#define FMC_SDSR_BUSY			(1 << 5)
+
+#define FMC_BUSY_WAIT()		do { \
+		__asm__ __volatile__ ("dsb" : : : "memory"); \
+		while (STM32_SDRAM_FMC->sdsr & FMC_SDSR_BUSY) \
+			; \
+	} while (0)
+
+
+#endif /* _MACH_FMC_H_ */

arch/arm/include/asm/arch-stm32f4/gpio.h

+/*
+ * (C) Copyright 2011
+ * Yuri Tikhonov, Emcraft Systems, yur@emcraft.com
+ *
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _STM32_GPIO_H_
+#define _STM32_GPIO_H_
+
+enum stm32_gpio_port {
+	STM32_GPIO_PORT_A = 0,
+	STM32_GPIO_PORT_B,
+	STM32_GPIO_PORT_C,
+	STM32_GPIO_PORT_D,
+	STM32_GPIO_PORT_E,
+	STM32_GPIO_PORT_F,
+	STM32_GPIO_PORT_G,
+	STM32_GPIO_PORT_H,
+	STM32_GPIO_PORT_I
+};
+
+enum stm32_gpio_pin {
+	STM32_GPIO_PIN_0 = 0,
+	STM32_GPIO_PIN_1,
+	STM32_GPIO_PIN_2,
+	STM32_GPIO_PIN_3,
+	STM32_GPIO_PIN_4,
+	STM32_GPIO_PIN_5,
+	STM32_GPIO_PIN_6,
+	STM32_GPIO_PIN_7,
+	STM32_GPIO_PIN_8,
+	STM32_GPIO_PIN_9,
+	STM32_GPIO_PIN_10,
+	STM32_GPIO_PIN_11,
+	STM32_GPIO_PIN_12,
+	STM32_GPIO_PIN_13,
+	STM32_GPIO_PIN_14,
+	STM32_GPIO_PIN_15
+};
+
+enum stm32_gpio_mode {
+	STM32_GPIO_MODE_IN = 0,
+	STM32_GPIO_MODE_OUT,
+	STM32_GPIO_MODE_AF,
+	STM32_GPIO_MODE_AN
+};
+
+enum stm32_gpio_otype {
+	STM32_GPIO_OTYPE_PP = 0,
+	STM32_GPIO_OTYPE_OD
+};
+
+enum stm32_gpio_speed {
+	STM32_GPIO_SPEED_2M = 0,
+	STM32_GPIO_SPEED_25M,
+	STM32_GPIO_SPEED_50M,
+	STM32_GPIO_SPEED_100M
+};
+
+enum stm32_gpio_pupd {
+	STM32_GPIO_PUPD_NO = 0,
+	STM32_GPIO_PUPD_UP,
+	STM32_GPIO_PUPD_DOWN
+};
+
+enum stm32_gpio_af {
+	STM32_GPIO_AF0 = 0,
+	STM32_GPIO_AF1,
+	STM32_GPIO_AF2,
+	STM32_GPIO_AF3,
+	STM32_GPIO_AF4,
+	STM32_GPIO_AF5,
+	STM32_GPIO_AF6,
+	STM32_GPIO_AF7,
+	STM32_GPIO_AF8,
+	STM32_GPIO_AF9,
+	STM32_GPIO_AF10,
+	STM32_GPIO_AF11,
+	STM32_GPIO_AF12,
+	STM32_GPIO_AF13,
+	STM32_GPIO_AF14,
+	STM32_GPIO_AF15
+};
+
+struct stm32_gpio_dsc {
+	enum stm32_gpio_port	port;
+	enum stm32_gpio_pin	pin;
+};
+
+struct stm32_gpio_ctl {
+	enum stm32_gpio_mode	mode;
+	enum stm32_gpio_otype	otype;
+	enum stm32_gpio_speed	speed;
+	enum stm32_gpio_pupd	pupd;
+	enum stm32_gpio_af	af;
+};
+
+static inline unsigned stm32_gpio_to_port(unsigned gpio)
+{
+	return gpio / 16;
+}
+
+static inline unsigned stm32_gpio_to_pin(unsigned gpio)
+{
+	return gpio % 16;
+}
+
+int stm32_gpio_config(const struct stm32_gpio_dsc *gpio_dsc,
+		const struct stm32_gpio_ctl *gpio_ctl);
+int stm32_gpout_set(const struct stm32_gpio_dsc *gpio_dsc, int state);
+
+#endif /* _STM32_GPIO_H_ */

arch/arm/include/asm/arch-stm32f4/stm32.h

+/*
+ * (C) Copyright 2011
+ * Yuri Tikhonov, Emcraft Systems, yur@emcraft.com
+ *
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _MACH_STM32_H_
+#define _MACH_STM32_H_
+
+/*
+ * Peripheral memory map
+ */
+#define STM32_PERIPH_BASE	0x40000000
+#define STM32_APB1PERIPH_BASE	(STM32_PERIPH_BASE + 0x00000000)
+#define STM32_APB2PERIPH_BASE	(STM32_PERIPH_BASE + 0x00010000)
+#define STM32_AHB1PERIPH_BASE	(STM32_PERIPH_BASE + 0x00020000)
+#define STM32_AHB2PERIPH_BASE	(STM32_PERIPH_BASE + 0x10000000)
+
+#define STM32_BUS_MASK		0xFFFF0000
+
+/*
+ * Register maps
+ */
+struct stm32_rcc_regs {
+	u32 cr;		/* RCC clock control */
+	u32 pllcfgr;	/* RCC PLL configuration */
+	u32 cfgr;	/* RCC clock configuration */
+	u32 cir;	/* RCC clock interrupt */
+	u32 ahb1rstr;	/* RCC AHB1 peripheral reset */
+	u32 ahb2rstr;	/* RCC AHB2 peripheral reset */
+	u32 ahb3rstr;	/* RCC AHB3 peripheral reset */
+	u32 rsv0;
+	u32 apb1rstr;	/* RCC APB1 peripheral reset */
+	u32 apb2rstr;	/* RCC APB2 peripheral reset */
+	u32 rsv1[2];
+	u32 ahb1enr;	/* RCC AHB1 peripheral clock enable */
+	u32 ahb2enr;	/* RCC AHB2 peripheral clock enable */
+	u32 ahb3enr;	/* RCC AHB3 peripheral clock enable */
+	u32 rsv2;
+	u32 apb1enr;	/* RCC APB1 peripheral clock enable */
+	u32 apb2enr;	/* RCC APB2 peripheral clock enable */
+	u32 rsv3[2];
+	u32 ahb1lpenr;	/* RCC AHB1 periph clk enable in low pwr mode */
+	u32 ahb2lpenr;	/* RCC AHB2 periph clk enable in low pwr mode */
+	u32 ahb3lpenr;	/* RCC AHB3 periph clk enable in low pwr mode */
+	u32 rsv4;
+	u32 apb1lpenr;	/* RCC APB1 periph clk enable in low pwr mode */
+	u32 apb2lpenr;	/* RCC APB2 periph clk enable in low pwr mode */
+	u32 rsv5[2];
+	u32 bdcr;	/* RCC Backup domain control */
+	u32 csr;	/* RCC clock control & status */
+	u32 rsv6[2];
+	u32 sscgr;	/* RCC spread spectrum clock generation */
+	u32 plli2scfgr;	/* RCC PLLI2S configuration */
+	u32 pllsaicfgr;
+	u32 dckcfgr;
+};
+
+struct stm32_pwr_regs {
+	u32 cr;
+	u32 csr;
+};
+
+struct stm32_flash_regs {
+	u32 acr;
+	u32 key;
+	u32 optkeyr;
+	u32 sr;
+	u32 cr;
+	u32 optcr;
+	u32 optcr1;
+};
+
+/*
+ * Registers access macros
+ */
+#define STM32_RCC_BASE		(STM32_AHB1PERIPH_BASE + 0x3800)
+#define STM32_RCC		((struct stm32_rcc_regs *)STM32_RCC_BASE)
+
+#define STM32_PWR_BASE		(STM32_APB1PERIPH_BASE + 0x7000)
+#define STM32_PWR		((struct stm32_pwr_regs *)STM32_PWR_BASE)
+
+#define STM32_FLASH_BASE	(STM32_AHB1PERIPH_BASE + 0x3C00)
+#define STM32_FLASH		((struct stm32_flash_regs *)STM32_FLASH_BASE)
+
+#define STM32_FLASH_SR_BSY		(1 << 16)
+
+#define STM32_FLASH_CR_PG		(1 << 0)
+#define STM32_FLASH_CR_SER		(1 << 1)
+#define STM32_FLASH_CR_STRT		(1 << 16)
+#define STM32_FLASH_CR_LOCK		(1 << 31)
+#define STM32_FLASH_CR_SNB_OFFSET	3
+
+enum clock {
+	CLOCK_CORE,
+	CLOCK_AHB,
+	CLOCK_APB1,
+	CLOCK_APB2
+};
+
+int configure_clocks(void);
+unsigned long clock_get(enum clock clck);
+
+#endif /* _MACH_STM32_H_ */

drivers/gpio/Makefile

@@ -42,3 +42,4 @@ obj-$(CONFIG_TCA642X)		+= tca642x.o
 oby-$(CONFIG_SX151X)		+= sx151x.o
 obj-$(CONFIG_SUNXI_GPIO)	+= sunxi_gpio.o
 obj-$(CONFIG_LPC32XX_GPIO)	+= lpc32xx_gpio.o
+obj-$(CONFIG_STM32_GPIO)	+= stm32_gpio.o

drivers/gpio/stm32_gpio.c

+/*
+ * (C) Copyright 2011
+ * Yuri Tikhonov, Emcraft Systems, yur@emcraft.com
+ *
+ * (C) Copyright 2015
+ * Kamil Lulko, <rev13@wp.pl>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define STM32_GPIOA_BASE	(STM32_AHB1PERIPH_BASE + 0x0000)
+#define STM32_GPIOB_BASE	(STM32_AHB1PERIPH_BASE + 0x0400)
+#define STM32_GPIOC_BASE	(STM32_AHB1PERIPH_BASE + 0x0800)
+#define STM32_GPIOD_BASE	(STM32_AHB1PERIPH_BASE + 0x0C00)
+#define STM32_GPIOE_BASE	(STM32_AHB1PERIPH_BASE + 0x1000)
+#define STM32_GPIOF_BASE	(STM32_AHB1PERIPH_BASE + 0x1400)
+#define STM32_GPIOG_BASE	(STM32_AHB1PERIPH_BASE + 0x1800)
+#define STM32_GPIOH_BASE	(STM32_AHB1PERIPH_BASE + 0x1C00)
+#define STM32_GPIOI_BASE	(STM32_AHB1PERIPH_BASE + 0x2000)
+
+static const unsigned long io_base[] = {
+	STM32_GPIOA_BASE, STM32_GPIOB_BASE, STM32_GPIOC_BASE,
+	STM32_GPIOD_BASE, STM32_GPIOE_BASE, STM32_GPIOF_BASE,
+	STM32_GPIOG_BASE, STM32_GPIOH_BASE, STM32_GPIOI_BASE
+};
+
+struct stm32_gpio_regs {
+	u32 moder;	/* GPIO port mode */
+	u32 otyper;	/* GPIO port output type */
+	u32 ospeedr;	/* GPIO port output speed */
+	u32 pupdr;	/* GPIO port pull-up/pull-down */
+	u32 idr;	/* GPIO port input data */
+	u32 odr;	/* GPIO port output data */
+	u32 bsrr;	/* GPIO port bit set/reset */
+	u32 lckr;	/* GPIO port configuration lock */
+	u32 afr[2];	/* GPIO alternate function */
+};
+
+#define CHECK_DSC(x)	(!x || x->port > 8 || x->pin > 15)
+#define CHECK_CTL(x)	(!x || x->af > 15 || x->mode > 3 || x->otype > 1 || \
+			x->pupd > 2 || x->speed > 3)
+
+int stm32_gpio_config(const struct stm32_gpio_dsc *dsc,
+		const struct stm32_gpio_ctl *ctl)
+{
+	struct stm32_gpio_regs *gpio_regs;
+	u32 i;
+	int rv;
+
+	if (CHECK_DSC(dsc)) {
+		rv = -EINVAL;
+		goto out;
+	}
+	if (CHECK_CTL(ctl)) {
+		rv = -EINVAL;
+		goto out;
+	}
+
+	gpio_regs = (struct stm32_gpio_regs *)io_base[dsc->port];
+
+	setbits_le32(&STM32_RCC->ahb1enr, 1 << dsc->port);
+
+	i = (dsc->pin & 0x07) * 4;
+	clrbits_le32(&gpio_regs->afr[dsc->pin >> 3], (0xF << i));
+	setbits_le32(&gpio_regs->afr[dsc->pin >> 3], ctl->af << i);
+
+	i = dsc->pin * 2;
+
+	clrbits_le32(&gpio_regs->moder, (0x3 << i));
+	setbits_le32(&gpio_regs->moder, ctl->mode << i);
+
+	clrbits_le32(&gpio_regs->otyper, (0x3 << i));
+	setbits_le32(&gpio_regs->otyper, ctl->otype << i);
+
+	clrbits_le32(&gpio_regs->ospeedr, (0x3 << i));
+	setbits_le32(&gpio_regs->ospeedr, ctl->speed << i);
+
+	clrbits_le32(&gpio_regs->pupdr, (0x3 << i));
+	setbits_le32(&gpio_regs->pupdr, ctl->pupd << i);
+
+	rv = 0;
+out:
+	return rv;
+}
+
+int stm32_gpout_set(const struct stm32_gpio_dsc *dsc, int state)
+{
+	struct stm32_gpio_regs	*gpio_regs;
+	int rv;
+
+	if (CHECK_DSC(dsc)) {
+		rv = -EINVAL;
+		goto out;
+	}
+
+	gpio_regs = (struct stm32_gpio_regs *)io_base[dsc->port];
+
+	if (state)
+		writel(1 << dsc->pin, &gpio_regs->bsrr);
+	else
+		writel(1 << (dsc->pin + 16), &gpio_regs->bsrr);
+
+	rv = 0;
+out:
+	return rv;
+}
+
+int stm32_gpin_get(const struct stm32_gpio_dsc *dsc)
+{
+	struct stm32_gpio_regs	*gpio_regs;
+	int rv;
+
+	if (CHECK_DSC(dsc)) {
+		rv = -EINVAL;
+		goto out;
+	}
+
+	gpio_regs = (struct stm32_gpio_regs *)io_base[dsc->port];
+	rv = readl(&gpio_regs->idr) & (1 << dsc->pin);
+out:
+	return rv;
+}
+
+/* Common GPIO API */
+
+int gpio_request(unsigned gpio, const char *label)
+{
+	return 0;
+}
+
+int gpio_free(unsigned gpio)
+{
+	return 0;
+}
+
+int gpio_direction_input(unsigned gpio)
+{
+	struct stm32_gpio_dsc dsc;
+	struct stm32_gpio_ctl ctl;
+
+	dsc.port = stm32_gpio_to_port(gpio);
+	dsc.pin = stm32_gpio_to_pin(gpio);
+	ctl.af = STM32_GPIO_AF0;
+	ctl.mode = STM32_GPIO_MODE_IN;
+	ctl.pupd = STM32_GPIO_PUPD_NO;
+	ctl.speed = STM32_GPIO_SPEED_50M;
+
+	return stm32_gpio_config(&dsc, &ctl);
+}
+
+int gpio_direction_output(unsigned gpio, int value)
+{
+	struct stm32_gpio_dsc dsc;
+	struct stm32_gpio_ctl ctl;
+	int res;
+
+	dsc.port = stm32_gpio_to_port(gpio);
+	dsc.pin = stm32_gpio_to_pin(gpio);
+	ctl.af = STM32_GPIO_AF0;
+	ctl.mode = STM32_GPIO_MODE_OUT;
+	ctl.otype = STM32_GPIO_OTYPE_PP;
+	ctl.pupd = STM32_GPIO_PUPD_NO;
+	ctl.speed = STM32_GPIO_SPEED_50M;
+
+	res = stm32_gpio_config(&dsc, &ctl);
+	if (res < 0)
+		goto out;
+	res = stm32_gpout_set(&dsc, value);
+out:
+	return res;
+}
+
+int gpio_get_value(unsigned gpio)
+{
+	struct stm32_gpio_dsc dsc;
+
+	dsc.port = stm32_gpio_to_port(gpio);
+	dsc.pin = stm32_gpio_to_pin(gpio);
+
+	return stm32_gpin_get(&dsc);
+}
+
+int gpio_set_value(unsigned gpio, int value)
+{
+	struct stm32_gpio_dsc dsc;
+
+	dsc.port = stm32_gpio_to_port(gpio);
+	dsc.pin = stm32_gpio_to_pin(gpio);
+
+	return stm32_gpout_set(&dsc, value);
+}

include/flash.h

@@ -459,6 +459,8 @@ extern flash_info_t *flash_get_info(ulong base);
 #define FLASH_S29GL064M 0x00F0		/* Spansion S29GL064M-R6		*/
 #define FLASH_S29GL128N 0x00F1		/* Spansion S29GL128N			*/
 
+#define FLASH_STM32F4	0x00F2		/* STM32F4 Embedded Flash */
+
 #define FLASH_UNKNOWN	0xFFFF		/* unknown flash type			*/