armv8/ls1043aqds: add DSPI support

Enable three DSPI flash memories on board.

Commands:
=> sf probe 1:0
SF: Detected N25Q128A with page size 256 Bytes,
				erase size 64 KiB, total 16 MiB
=> sf probe 1:1
SF: Detected SST25WF040B with page size 256 Bytes,
				erase size 4 KiB, total 512 KiB
=> sf probe 1:2
SF: Detected EN25S64 with page size 256 Bytes,
				erase size 64 KiB, total 8 MiB

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>

configs/ls1043aqds_defconfig

@@ -4,3 +4,6 @@ CONFIG_TARGET_LS1043AQDS=y
 CONFIG_SYS_NS16550=y
 CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
 CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI=y

configs/ls1043aqds_nand_defconfig

@@ -3,3 +3,8 @@ CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL,NAND_BOOT"
 CONFIG_ARM=y
 CONFIG_TARGET_LS1043AQDS=y
 CONFIG_SYS_NS16550=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI=y

configs/ls1043aqds_nor_ddr3_defconfig

 CONFIG_ARM=y
 CONFIG_TARGET_LS1043AQDS=y
 CONFIG_SYS_NS16550=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI=y

configs/ls1043aqds_sdcard_ifc_defconfig

@@ -3,3 +3,8 @@ CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT"
 CONFIG_ARM=y
 CONFIG_TARGET_LS1043AQDS=y
 CONFIG_SYS_NS16550=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart"
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI=y

include/configs/ls1043a_common.h

@@ -197,6 +197,18 @@
 #define CONFIG_DOS_PARTITION
 #endif
 
+/*  DSPI  */
+#define CONFIG_FSL_DSPI
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_CMD_SF
+#define CONFIG_DM_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
+#define CONFIG_SPI_FLASH_SST		/* cs1 */
+#define CONFIG_SPI_FLASH_EON		/* cs2 */
+#define CONFIG_SF_DEFAULT_BUS		1
+#define CONFIG_SF_DEFAULT_CS		0
+#endif
+
 #define CONFIG_FSL_CAAM			/* Enable SEC/CAAM */
 
 /* FMan ucode */

include/configs/ls1043ardb.h

@@ -222,16 +222,6 @@
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
 
-/* DSPI */
-#define CONFIG_FSL_DSPI
-#ifdef CONFIG_FSL_DSPI
-#define CONFIG_CMD_SF
-#define CONFIG_DM_SPI_FLASH
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SF_DEFAULT_BUS		1
-#define CONFIG_SF_DEFAULT_CS		0
-#endif
-
 /*
  * Environment
  */