powerpc/QorIQ: fix network frame manager TBI PHY address settings

TBI PHY address (TBIPA) register has been set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c

So remove the duplicate code on QorIQ frame manager Ethernet related
platforms, which include Hydra board, P4080DS board and P2041rdb board.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

board/freescale/corenet_ds/eth_hydra.c

@@ -377,7 +377,6 @@ void fdt_fixup_board_enet(void *fdt)
 int board_eth_init(bd_t *bis)
 {
 #ifdef CONFIG_FMAN_ENET
-	struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
 	struct fsl_pq_mdio_info dtsec_mdio_info;
 	struct tgec_mdio_info tgec_mdio_info;
 	unsigned int i, slot;
@@ -387,13 +386,6 @@ int board_eth_init(bd_t *bis)
 
 	initialize_lane_to_slot();
 
-	/*
-	 * Set TBIPA on FM1@DTSEC1.  This is needed for configurations
-	 * where FM1@DTSEC1 isn't used directly, since it provides
-	 * MDIO for other ports.
-	 */
-	out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
 	/* We want to use the PIXIS to configure MUX routing, not GPIOs. */
 	setbits_8(&pixis->brdcfg2, BRDCFG2_REG_GPIO_SEL);
 

board/freescale/corenet_ds/eth_p4080.c

@@ -301,7 +301,6 @@ int board_eth_init(bd_t *bis)
 {
 #ifdef CONFIG_FMAN_ENET
 	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
-	struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
 	int i;
 	struct fsl_pq_mdio_info dtsec_mdio_info;
 	struct tgec_mdio_info tgec_mdio_info;
@@ -327,13 +326,6 @@ int board_eth_init(bd_t *bis)
 		SLOT5, /* 17 - Bank 3:D */
 	};
 
-	/*
-	 * Set TBIPA on FM1@DTSEC1.  This is needed for configurations
-	 * where FM1@DTSEC1 isn't used directly, since it provides
-	 * MDIO for other ports.
-	 */
-	out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
 	/* Initialize the mdio_mux array so we can recognize empty elements */
 	for (i = 0; i < NUM_FM_PORTS; i++)
 		mdio_mux[i] = EMI_NONE;

board/freescale/p2041rdb/eth.c

@@ -139,7 +139,6 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 int board_eth_init(bd_t *bis)
 {
 #ifdef CONFIG_FMAN_ENET
-	struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
 	struct fsl_pq_mdio_info dtsec_mdio_info;
 	struct tgec_mdio_info tgec_mdio_info;
 	unsigned int i, slot;
@@ -149,13 +148,6 @@ int board_eth_init(bd_t *bis)
 
 	initialize_lane_to_slot();
 
-	/*
-	 * Set TBIPA on FM1@DTSEC1.  This is needed for configurations
-	 * where FM1@DTSEC1 isn't used directly, since it provides
-	 * MDIO for other ports.
-	 */
-	out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
-
 	dtsec_mdio_info.regs =
 		(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
 	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;