superio: Add SMSC SIO1007 driver

The SMSC SIO1007 superio chipset integrates two ns16550 compatible
serial ports for legacy applications, 16 GPIO pins and some other
functionalities like power management.

This adds a simple driver to enable serial port and handle GPIO.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

drivers/misc/Makefile

@@ -32,6 +32,7 @@ ifdef CONFIG_DM_I2C
 obj-$(CONFIG_SANDBOX) += i2c_eeprom_emul.o
 endif
 obj-$(CONFIG_SMSC_LPC47M) += smsc_lpc47m.o
+obj-$(CONFIG_SMSC_SIO1007) += smsc_sio1007.o
 obj-$(CONFIG_STATUS_LED) += status_led.o
 obj-$(CONFIG_SANDBOX) += swap_case.o
 obj-$(CONFIG_SANDBOX) += syscon_sandbox.o

drivers/misc/smsc_sio1007.c

+/*
+ * Copyright (C) 2016, Bin Meng <bmeng.cn@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <smsc_sio1007.h>
+
+static inline u8 sio1007_read(int port, int reg)
+{
+	outb(reg, port);
+
+	return inb(port + 1);
+}
+
+static inline void sio1007_write(int port, int reg, int val)
+{
+	outb(reg, port);
+	outb(val, port + 1);
+}
+
+static inline void sio1007_clrsetbits(int port, int reg, u8 clr, u8 set)
+{
+	sio1007_write(port, reg, (sio1007_read(port, reg) & ~clr) | set);
+}
+
+void sio1007_enable_serial(int port, int num, int iobase, int irq)
+{
+	if (num < 0 || num > SIO1007_UART_NUM)
+		return;
+
+	/* enter configuration state */
+	outb(0x55, port);
+
+	/* power on serial port and set up its i/o base & irq */
+	if (!num) {
+		sio1007_clrsetbits(port, DEV_POWER_CTRL, 0, UART1_POWER_ON);
+		sio1007_clrsetbits(port, UART1_IOBASE, 0xfe, iobase >> 2);
+		sio1007_clrsetbits(port, UART_IRQ, 0xf0, irq << 4);
+	} else {
+		sio1007_clrsetbits(port, DEV_POWER_CTRL, 0, UART2_POWER_ON);
+		sio1007_clrsetbits(port, UART2_IOBASE, 0xfe, iobase >> 2);
+		sio1007_clrsetbits(port, UART_IRQ, 0x0f, irq);
+	}
+
+	/* exit configuration state */
+	outb(0xaa, port);
+}
+
+void sio1007_enable_runtime(int port, int iobase)
+{
+	/* enter configuration state */
+	outb(0x55, port);
+
+	/* set i/o base for the runtime register block */
+	sio1007_clrsetbits(port, RTR_IOBASE_LOW, 0, iobase >> 4);
+	sio1007_clrsetbits(port, RTR_IOBASE_HIGH, 0, iobase >> 12);
+	/* turn on address decoding for this block */
+	sio1007_clrsetbits(port, DEV_ACTIVATE, 0, RTR_EN);
+
+	/* exit configuration state */
+	outb(0xaa, port);
+}
+
+void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type)
+{
+	int reg = GPIO0_DIR;
+
+	if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
+		return;
+	if (gpio >= GPIO_NUM_PER_GROUP) {
+		reg = GPIO1_DIR;
+		gpio -= GPIO_NUM_PER_GROUP;
+	}
+
+	/* enter configuration state */
+	outb(0x55, port);
+
+	/* set gpio pin direction, polority and type */
+	sio1007_clrsetbits(port, reg, 1 << gpio, dir << gpio);
+	sio1007_clrsetbits(port, reg + 1, 1 << gpio, pol << gpio);
+	sio1007_clrsetbits(port, reg + 2, 1 << gpio, type << gpio);
+
+	/* exit configuration state */
+	outb(0xaa, port);
+}
+
+int sio1007_gpio_get_value(int port, int gpio)
+{
+	int reg = GPIO0_DATA;
+	int val;
+
+	if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
+		return -EINVAL;
+	if (gpio >= GPIO_NUM_PER_GROUP) {
+		reg = GPIO1_DATA;
+		gpio -= GPIO_NUM_PER_GROUP;
+	}
+
+	val = inb(port + reg);
+	if (val & (1 << gpio))
+		return 1;
+	else
+		return 0;
+}
+
+void sio1007_gpio_set_value(int port, int gpio, int val)
+{
+	int reg = GPIO0_DATA;
+	u8 data;
+
+	if (gpio < 0 || gpio > SIO1007_GPIO_NUM)
+		return;
+	if (gpio >= GPIO_NUM_PER_GROUP) {
+		reg = GPIO1_DATA;
+		gpio -= GPIO_NUM_PER_GROUP;
+	}
+
+	data = inb(port + reg);
+	data &= ~(1 << gpio);
+	data |= (val << gpio);
+	outb(data, port + reg);
+}

include/smsc_sio1007.h

+/*
+ * Copyright (C) 2016, Bin Meng <bmeng.cn@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _SMSC_SIO1007_H_
+#define _SMSC_SIO1007_H_
+
+/*
+ * The I/O base address of SIO1007 at power-up is determined by the SYSOPT0
+ * and SYSOPT1 pins at the deasserting edge of PCIRST#. The combination of
+ * SYSOPT0 and SYSOPT1 determines one of the following addresses.
+ */
+#define SIO1007_IOPORT0		0x002e
+#define SIO1007_IOPORT1		0x004e
+#define SIO1007_IOPORT2		0x162e
+#define SIO1007_IOPORT3		0x164e
+
+/* SIO1007 registers */
+
+#define DEV_POWER_CTRL		0x02
+#define UART1_POWER_ON		(1 << 3)
+#define UART2_POWER_ON		(1 << 7)
+
+#define UART1_IOBASE		0x24
+#define UART2_IOBASE		0x25
+#define UART_IRQ		0x28
+
+#define RTR_IOBASE_HIGH		0x21
+#define RTR_IOBASE_LOW		0x30
+
+#define GPIO0_DIR		0x31
+#define GPIO1_DIR		0x35
+#define GPIO_DIR_INPUT		0
+#define GPIO_DIR_OUTPUT		1
+
+#define GPIO0_POL		0x32
+#define GPIO1_POL		0x36
+#define GPIO_POL_NO_INVERT	0
+#define GPIO_POL_INVERT		1
+
+#define GPIO0_TYPE		0x33
+#define GPIO1_TYPE		0x37
+#define GPIO_TYPE_PUSH_PULL	0
+#define GPIO_TYPE_OPEN_DRAIN	1
+
+#define DEV_ACTIVATE		0x3a
+#define RTR_EN			(1 << 1)
+
+/* Runtime register offset */
+
+#define GPIO0_DATA		0xc
+#define GPIO1_DATA		0xe
+
+/* Number of serial ports supported */
+#define SIO1007_UART_NUM	2
+
+/* Number of gpio pins supported */
+#define GPIO_NUM_PER_GROUP	8
+#define GPIO_GROUP_NUM		2
+#define SIO1007_GPIO_NUM	(GPIO_NUM_PER_GROUP * GPIO_GROUP_NUM)
+
+/**
+ * Configure the I/O port address of the specified serial device and
+ * enable the serial device.
+ *
+ * @port:	SIO1007 I/O port address
+ * @num:	serial device number (0 or 1)
+ * @iobase:	processor I/O port address to assign to this serial device
+ * @irq:	processor IRQ number to assign to this serial device
+ */
+void sio1007_enable_serial(int port, int num, int iobase, int irq);
+
+/**
+ * Configure the I/O port address of the runtime register block and
+ * enable the address decoding.
+ *
+ * @port:	SIO1007 I/O port address
+ * @iobase:	processor I/O port address to assign to the runtime registers
+ */
+void sio1007_enable_runtime(int port, int iobase);
+
+/**
+ * Configure the direction/polority/type of a specified GPIO pin
+ *
+ * @port:	SIO1007 I/O port address
+ * @gpio:	GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
+ * @dir:	GPIO_DIR_INPUT or GPIO_DIR_OUTPUT
+ * @pol:	GPIO_POL_NO_INVERT or GPIO_POL_INVERT
+ * @type:	GPIO_TYPE_PUSH_PULL or GPIO_TYPE_OPEN_DRAIN
+ */
+void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type);
+
+/**
+ * Get a GPIO pin value.
+ * This will work whether the GPIO is an input or an output.
+ *
+ * @port:	runtime register block I/O port address
+ * @gpio:	GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
+ * @return:	0 if low, 1 if high, -EINVAL if gpio number is invalid
+ */
+int sio1007_gpio_get_value(int port, int gpio);
+
+/**
+ * Set a GPIO pin value.
+ * This will only work when the GPIO is configured as an output.
+ *
+ * @port:	runtime register block I/O port address
+ * @gpio:	GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
+ * @val:	0 if low, 1 if high
+ */
+void sio1007_gpio_set_value(int port, int gpio, int val);
+
+#endif /* _SMSC_SIO1007_H_ */