u8500: Moving processor-specific functions to cpu area.

Functions such as providing power to the MMC device and reading
the processor version register should be in the cpu area for
access by multiple u8500-based boards.

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>

arch/arm/cpu/armv7/u8500/cpu.c

@@ -28,6 +28,24 @@
 #include <asm/io.h>
 #include <asm/arch/prcmu.h>
 #include <asm/arch/clock.h>
+#include <asm/arch/hardware.h>
+
+#include <asm/arch/hardware.h>
+
+#define CPUID_DB8500V1		0x411fc091
+#define ASICID_DB8500V11	0x008500A1
+
+static unsigned int read_asicid(void)
+{
+	unsigned int *address = (void *)U8500_BOOTROM_BASE
+				+ U8500_BOOTROM_ASIC_ID_OFFSET;
+	return readl(address);
+}
+
+static int cpu_is_u8500v11(void)
+{
+	return read_asicid() == ASICID_DB8500V11;
+}
 
 #ifdef CONFIG_ARCH_CPU_INIT
 /*
@@ -41,3 +59,65 @@ int arch_cpu_init(void)
 	return 0;
 }
 #endif /* CONFIG_ARCH_CPU_INIT */
+
+#ifdef CONFIG_MMC
+
+#define LDO_VAUX3_MASK		0x3
+#define LDO_VAUX3_ENABLE	0x1
+#define VAUX3_VOLTAGE_2_9V	0xd
+
+#define AB8500_REGU_CTRL2	0x4
+#define AB8500_REGU_VRF1VAUX3_REGU_REG	0x040A
+#define AB8500_REGU_VRF1VAUX3_SEL_REG	0x0421
+
+int u8500_mmc_power_init(void)
+{
+	int ret;
+	int val;
+
+	if (!cpu_is_u8500v11())
+		return 0;
+
+	/*
+	 * On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD
+	 * card to work.  This is done by enabling the regulators in the AB8500
+	 * via PRCMU I2C transactions.
+	 *
+	 * This code is derived from the handling of AB8500_LDO_VAUX3 in
+	 * ab8500_ldo_enable() and ab8500_ldo_disable() in Linux.
+	 *
+	 * Turn off and delay is required to have it work across soft reboots.
+	 */
+
+	ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG);
+	if (ret < 0)
+		goto out;
+
+	val = ret;
+
+	/* Turn off */
+	ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG,
+							val & ~LDO_VAUX3_MASK);
+	if (ret < 0)
+		goto out;
+
+	udelay(10 * 1000);
+
+	/* Set the voltage to 2.9V */
+	ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
+				AB8500_REGU_VRF1VAUX3_SEL_REG,
+				VAUX3_VOLTAGE_2_9V);
+	if (ret < 0)
+		goto out;
+
+	val = val & ~LDO_VAUX3_MASK;
+	val = val | LDO_VAUX3_ENABLE;
+
+	/* Turn on the supply */
+	ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
+				AB8500_REGU_VRF1VAUX3_REGU_REG, val);
+
+out:
+	return ret;
+}
+#endif /* CONFIG_MMC */

arch/arm/include/asm/arch-u8500/sys_proto.h

@@ -23,5 +23,6 @@
 #define _SYS_PROTO_H_
 
 void gpio_init(void);
+int u8500_mmc_power_init(void);
 
 #endif  /* _SYS_PROTO_H_ */

board/st-ericsson/u8500/u8500_href.c

@@ -138,18 +138,6 @@ void show_boot_progress(int progress)
 }
 #endif
 
-static unsigned int read_asicid(void)
-{
-	unsigned int *address = (void *)U8500_BOOTROM_BASE
-				+ U8500_BOOTROM_ASIC_ID_OFFSET;
-	return readl(address);
-}
-
-int cpu_is_u8500v11(void)
-{
-	return read_asicid() == 0x008500A1;
-}
-
 /*
  * Miscellaneous platform dependent initialisations
  */
@@ -226,67 +214,6 @@ unsigned int addr_vall_arr[] = {
 };
 
 #ifdef CONFIG_BOARD_LATE_INIT
-#ifdef CONFIG_MMC
-
-#define LDO_VAUX3_MASK		0x3
-#define LDO_VAUX3_ENABLE	0x1
-#define VAUX3_VOLTAGE_2_9V	0xd
-
-#define AB8500_REGU_CTRL2	0x4
-#define AB8500_REGU_VRF1VAUX3_REGU_REG	0x040A
-#define AB8500_REGU_VRF1VAUX3_SEL_REG	0x0421
-
-static int hrefplus_mmc_power_init(void)
-{
-	int ret;
-	int val;
-
-	if (!cpu_is_u8500v11())
-		return 0;
-
-	/*
-	 * On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD
-	 * card to work.  This is done by enabling the regulators in the AB8500
-	 * via PRCMU I2C transactions.
-	 *
-	 * This code is derived from the handling of AB8500_LDO_VAUX3 in
-	 * ab8500_ldo_enable() and ab8500_ldo_disable() in Linux.
-	 *
-	 * Turn off and delay is required to have it work across soft reboots.
-	 */
-
-	ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG);
-	if (ret < 0)
-		goto out;
-
-	val = ret;
-
-	/* Turn off */
-	ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG,
-				val & ~LDO_VAUX3_MASK);
-	if (ret < 0)
-		goto out;
-
-	udelay(10 * 1000);
-
-	/* Set the voltage to 2.9V */
-	ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
-				AB8500_REGU_VRF1VAUX3_SEL_REG,
-				VAUX3_VOLTAGE_2_9V);
-	if (ret < 0)
-		goto out;
-
-	val = val & ~LDO_VAUX3_MASK;
-	val = val | LDO_VAUX3_ENABLE;
-
-	/* Turn on the supply */
-	ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
-				AB8500_REGU_VRF1VAUX3_REGU_REG, val);
-
-out:
-	return ret;
-}
-#endif
 /*
  * called after all initialisation were done, but before the generic
  * mmc_initialize().
@@ -313,7 +240,7 @@ int board_late_init(void)
 		setenv("board_id", "1");
 	}
 #ifdef CONFIG_MMC
-	hrefplus_mmc_power_init();
+	u8500_mmc_power_init();
 
 	/*
 	 * config extended GPIO pins for level shifter and