Newer
Older
* Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* U-boot - Common settings for UniPhier Family */
#ifndef __CONFIG_UNIPHIER_COMMON_H__
#define __CONFIG_UNIPHIER_COMMON_H__
#if defined(CONFIG_MACH_PH1_PRO4)
#define CONFIG_DDR_NUM_CH0 2
#define CONFIG_DDR_NUM_CH1 2
/* Physical start address of SDRAM */
#define CONFIG_SDRAM0_BASE 0x80000000
#define CONFIG_SDRAM0_SIZE 0x20000000
#define CONFIG_SDRAM1_BASE 0xa0000000
#define CONFIG_SDRAM1_SIZE 0x20000000
#endif
#if defined(CONFIG_MACH_PH1_LD4)
#define CONFIG_DDR_NUM_CH0 1
#define CONFIG_DDR_NUM_CH1 1
/* Physical start address of SDRAM */
#define CONFIG_SDRAM0_BASE 0x80000000
#define CONFIG_SDRAM0_SIZE 0x10000000
#define CONFIG_SDRAM1_BASE 0x90000000
#define CONFIG_SDRAM1_SIZE 0x10000000
#endif
#if defined(CONFIG_MACH_PH1_SLD8)
#define CONFIG_DDR_NUM_CH0 1
#define CONFIG_DDR_NUM_CH1 1
/* Physical start address of SDRAM */
#define CONFIG_SDRAM0_BASE 0x80000000
#define CONFIG_SDRAM0_SIZE 0x10000000
#define CONFIG_SDRAM1_BASE 0x90000000
#define CONFIG_SDRAM1_SIZE 0x10000000
#endif
#define CONFIG_I2C_EEPROM
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/*
* Support card address map
*/
#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
# define CONFIG_SUPPORT_CARD_BASE 0x03f00000
# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
#endif
#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
# define CONFIG_SUPPORT_CARD_BASE 0x08000000
# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
#endif
#ifdef CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE
#define CONFIG_SYS_NS16550_CLK 12288000
#define CONFIG_SYS_NS16550_REG_SIZE -2
/* TODO: move to Kconfig and device tree */
#if 0
#define CONFIG_SYS_NS16550_SERIAL
#endif
#define CONFIG_SMC911X
#define CONFIG_SMC911X_BASE CONFIG_SUPPORT_CARD_ETHER_BASE
#define CONFIG_SMC911X_32_BIT
/*-----------------------------------------------------------------------
* MMU and Cache Setting
*----------------------------------------------------------------------*/
/* Comment out the following to enable L1 cache */
/* #define CONFIG_SYS_ICACHE_OFF */
/* #define CONFIG_SYS_DCACHE_OFF */
#define CONFIG_SYS_CACHELINE_SIZE 32
/* Comment out the following to enable L2 cache */
#define CONFIG_UNIPHIER_L2CACHE_ON
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#define CONFIG_TIMESTAMP
/* FLASH related */
#define CONFIG_MTD_DEVICE
/*
* uncomment the following to disable FLASH related code.
*/
/* #define CONFIG_SYS_NO_FLASH */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_MAX_FLASH_SECT 256
#define CONFIG_SYS_MONITOR_BASE 0
#define CONFIG_SYS_FLASH_BASE 0
/*
* flash_toggle does not work for out supoort card.
* We need to use flash_status_poll.
*/
#define CONFIG_SYS_CFI_FLASH_STATUS_POLL
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
/* serial console configuration */
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_GENERIC_BOARD
#if !defined(CONFIG_SPL_BUILD)
#define CONFIG_USE_ARCH_MEMSET
#define CONFIG_USE_ARCH_MEMCPY
#endif
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* add command line history */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
#define CONFIG_CONS_INDEX 1
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
*/
/* #define CONFIG_ENV_IS_IN_NAND */
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET 0x0
/* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
/* Time clock 1MHz */
#define CONFIG_SYS_TIMER_RATE 1000000
/*
* By default, ARP timeout is 5 sec.
* The first ARP request does not seem to work.
* So we need to retry ARP request anyway.
* We want to shrink the interval until the second ARP request.
*/
#define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_MAX_CHIPS 2
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_NAND_DENALI_ECC_SIZE 1024
#define CONFIG_SYS_NAND_REGS_BASE 0x68100000
#define CONFIG_SYS_NAND_DATA_BASE 0x68000000
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10)
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
/* USB */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 4
#define CONFIG_CMD_FAT
#define CONFIG_FAT_WRITE
#define CONFIG_DOS_PARTITION
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000)
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_AUTOBOOT_KEYED 1
#define CONFIG_AUTOBOOT_PROMPT \
"Press SPACE to abort autoboot in %d seconds\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR "d"
#define CONFIG_AUTOBOOT_STOP_STR " "
/*
* Network Configuration
*/
#define CONFIG_SERVERIP 192.168.11.1
#define CONFIG_IPADDR 192.168.11.10
#define CONFIG_GATEWAYIP 192.168.11.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_LOADADDR 0x84000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_BOOTFILE "fit.itb"
#define CONFIG_CMDLINE_EDITING /* add command line history */
#define CONFIG_BOOTCOMMAND "run $bootmode"
#define CONFIG_ROOTPATH "/nfs/root/path"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs $bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
"tftpboot; bootm;"
#define CONFIG_BOOTARGS " user_debug=0x1f init=/sbin/init"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"image_offset=0x00080000\0" \
"image_size=0x00f00000\0" \
"verify=n\0" \
"nandupdate=nand erase 0 0x100000 &&" \
"tftpboot u-boot-spl.bin &&" \
"nand write $loadaddr 0 0x10000 &&" \
"tftpboot u-boot-dtb.img &&" \
"nand write $loadaddr 0x10000 0xf0000\0" \
"norboot=run add_default_bootargs &&" \
"bootm $image_offset\0" \
"nandboot=run add_default_bootargs &&" \
"nand read $loadaddr $image_offset $image_size &&" \
"bootm\0" \
"add_default_bootargs=setenv bootargs $bootargs" \
" console=ttyS0,$baudrate\0" \
/* Open Firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_HAVE_ARM_SECURE
/* Memory Size & Mapping */
#define CONFIG_SYS_SDRAM_BASE CONFIG_SDRAM0_BASE
#if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
/* Thre is no memory hole */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
#else
#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE)
#endif
#if defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8)
#define CONFIG_SPL_TEXT_BASE 0x00040000
#endif
#if defined(CONFIG_MACH_PH1_PRO4)
#define CONFIG_SPL_TEXT_BASE 0x00100000
#endif
#define CONFIG_SPL_STACK (0x0ff08000)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE)
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000
#define CONFIG_SPL_MAX_FOOTPRINT 0x10000
#endif /* __CONFIG_UNIPHIER_COMMON_H__ */