gpio.h

/*
 * Copyright (c) 2011 The Chromium OS Authors.
 * Copyright (c) 2011, NVIDIA Corp. All rights reserved.
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _ASM_GENERIC_GPIO_H_
#define _ASM_GENERIC_GPIO_H_

/*
 * Generic GPIO API for U-Boot
 *
 * GPIOs are numbered from 0 to GPIO_COUNT-1 which value is defined
 * by the SOC/architecture.
 *
 * Each GPIO can be an input or output. If an input then its value can
 * be read as 0 or 1. If an output then its value can be set to 0 or 1.
 * If you try to write an input then the value is undefined. If you try
 * to read an output, barring something very unusual,  you will get
 * back the value of the output that you previously set.
 *
 * In some cases the operation may fail, for example if the GPIO number
 * is out of range, or the GPIO is not available because its pin is
 * being used by another function. In that case, functions may return
 * an error value of -1.
 */

/**
 * Request a GPIO. This should be called before any of the other functions
 * are used on this GPIO.
 *
 * Note: With driver model, the label is allocated so there is no need for
 * the caller to preserve it.
 *
 * @param gp	GPIO number
 * @param label	User label for this GPIO
 * @return 0 if ok, -1 on error
 */
int gpio_request(unsigned gpio, const char *label);

/**
 * Stop using the GPIO.  This function should not alter pin configuration.
 *
 * @param gpio	GPIO number
 * @return 0 if ok, -1 on error
 */
int gpio_free(unsigned gpio);

/**
 * Make a GPIO an input.
 *
 * @param gpio	GPIO number
 * @return 0 if ok, -1 on error
 */
int gpio_direction_input(unsigned gpio);

/**
 * Make a GPIO an output, and set its value.
 *
 * @param gpio	GPIO number
 * @param value	GPIO value (0 for low or 1 for high)
 * @return 0 if ok, -1 on error
 */
int gpio_direction_output(unsigned gpio, int value);

/**
 * Get a GPIO's value. This will work whether the GPIO is an input
 * or an output.
 *
 * @param gpio	GPIO number
 * @return 0 if low, 1 if high, -1 on error
 */
int gpio_get_value(unsigned gpio);

/**
 * Set an output GPIO's value. The GPIO must already be an output or
 * this function may have no effect.
 *
 * @param gpio	GPIO number
 * @param value	GPIO value (0 for low or 1 for high)
 * @return 0 if ok, -1 on error
 */
int gpio_set_value(unsigned gpio, int value);

/* State of a GPIO, as reported by get_function() */
enum gpio_func_t {
	GPIOF_INPUT = 0,
	GPIOF_OUTPUT,
	GPIOF_UNUSED,		/* Not claimed */
	GPIOF_UNKNOWN,		/* Not known */
	GPIOF_FUNC,		/* Not used as a GPIO */

	GPIOF_COUNT,
};

struct udevice;

/**
 * gpio_get_status() - get the current GPIO status as a string
 *
 * Obtain the current GPIO status as a string which can be presented to the
 * user. A typical string is:
 *
 * "b4:  in: 1 [x] sdmmc_cd"
 *
 * which means this is GPIO bank b, offset 4, currently set to input, current
 * value 1, [x] means that it is requested and the owner is 'sdmmc_cd'
 *
 * @dev:	Device to check
 * @offset:	Offset of device GPIO to check
 * @buf:	Place to put string
 * @buffsize:	Size of string including \0
 */
int gpio_get_status(struct udevice *dev, int offset, char *buf, int buffsize);

/**
 * gpio_get_function() - get the current function for a GPIO pin
 *
 * Note this returns GPIOF_UNUSED if the GPIO is not requested.
 *
 * @dev:	Device to check
 * @offset:	Offset of device GPIO to check
 * @namep:	If non-NULL, this is set to the nane given when the GPIO
 *		was requested, or -1 if it has not been requested
 * @return  -ENODATA if the driver returned an unknown function,
 * -ENODEV if the device is not active, -EINVAL if the offset is invalid.
 * GPIOF_UNUSED if the GPIO has not been requested. Otherwise returns the
 * function from enum gpio_func_t.
 */
int gpio_get_function(struct udevice *dev, int offset, const char **namep);

/**
 * gpio_get_raw_function() - get the current raw function for a GPIO pin
 *
 * Note this does not return GPIOF_UNUSED - it will always return the GPIO
 * driver's view of a pin function, even if it is not correctly set up.
 *
 * @dev:	Device to check
 * @offset:	Offset of device GPIO to check
 * @namep:	If non-NULL, this is set to the nane given when the GPIO
 *		was requested, or -1 if it has not been requested
 * @return  -ENODATA if the driver returned an unknown function,
 * -ENODEV if the device is not active, -EINVAL if the offset is invalid.
 * Otherwise returns the function from enum gpio_func_t.
 */
int gpio_get_raw_function(struct udevice *dev, int offset, const char **namep);

/**
 * gpio_requestf() - request a GPIO using a format string for the owner
 *
 * This is a helper function for gpio_request(). It allows you to provide
 * a printf()-format string for the GPIO owner. It calls gpio_request() with
 * the string that is created
 */
int gpio_requestf(unsigned gpio, const char *fmt, ...)
		__attribute__ ((format (__printf__, 2, 3)));

/**
 * struct struct dm_gpio_ops - Driver model GPIO operations
 *
 * Refer to functions above for description. These function largely copy
 * the old API.
 *
 * This is trying to be close to Linux GPIO API. Once the U-Boot uses the
 * new DM GPIO API, this should be really easy to flip over to the Linux
 * GPIO API-alike interface.
 *
 * Also it would be useful to standardise additional functions like
 * pullup, slew rate and drive strength.
 *
 * gpio_request)( and gpio_free() are optional - if NULL then they will
 * not be called.
 *
 * Note that @offset is the offset from the base GPIO of the device. So
 * offset 0 is the device's first GPIO and offset o-1 is the last GPIO,
 * where o is the number of GPIO lines controlled by the device. A device
 * is typically used to control a single bank of GPIOs. Within complex
 * SoCs there may be many banks and therefore many devices all referring
 * to the different IO addresses within the SoC.
 *
 * The uclass combines all GPIO devices together to provide a consistent
 * numbering from 0 to n-1, where n is the number of GPIOs in total across
 * all devices. Be careful not to confuse offset with gpio in the parameters.
 */
struct dm_gpio_ops {
	int (*request)(struct udevice *dev, unsigned offset, const char *label);
	int (*free)(struct udevice *dev, unsigned offset);
	int (*direction_input)(struct udevice *dev, unsigned offset);
	int (*direction_output)(struct udevice *dev, unsigned offset,
				int value);
	int (*get_value)(struct udevice *dev, unsigned offset);
	int (*set_value)(struct udevice *dev, unsigned offset, int value);
	/**
	 * get_function() Get the GPIO function
	 *
	 * @dev:     Device to check
	 * @offset:  GPIO offset within that device
	 * @return current function - GPIOF_...
	 */
	int (*get_function)(struct udevice *dev, unsigned offset);
};

/**
 * struct gpio_dev_priv - information about a device used by the uclass
 *
 * The uclass combines all active GPIO devices into a unified numbering
 * scheme. To do this it maintains some private information about each
 * device.
 *
 * To implement driver model support in your GPIO driver, add a probe
 * handler, and set @gpio_count and @bank_name correctly in that handler.
 * This tells the uclass the name of the GPIO bank and the number of GPIOs
 * it contains.
 *
 * @bank_name: Name of the GPIO device (e.g 'a' means GPIOs will be called
 * 'A0', 'A1', etc.
 * @gpio_count: Number of GPIOs in this device
 * @gpio_base: Base GPIO number for this device. For the first active device
 * this will be 0; the numbering for others will follow sequentially so that
 * @gpio_base for device 1 will equal the number of GPIOs in device 0.
 * @name: Array of pointers to the name for each GPIO in this bank. The
 * value of the pointer will be NULL if the GPIO has not been claimed.
 */
struct gpio_dev_priv {
	const char *bank_name;
	unsigned gpio_count;
	unsigned gpio_base;
	char **name;
};

/* Access the GPIO operations for a device */
#define gpio_get_ops(dev)	((struct dm_gpio_ops *)(dev)->driver->ops)

/**
 * gpio_get_bank_info - Return information about a GPIO bank/device
 *
 * This looks up a device and returns both its GPIO base name and the number
 * of GPIOs it controls.
 *
 * @dev: Device to look up
 * @offset_count: Returns number of GPIOs within this bank
 * @return bank name of this device
 */
const char *gpio_get_bank_info(struct udevice *dev, int *offset_count);

/**
 * gpio_lookup_name - Look up a GPIO name and return its details
 *
 * This is used to convert a named GPIO into a device, offset and GPIO
 * number.
 *
 * @name: GPIO name to look up
 * @devp: Returns pointer to device which contains this GPIO
 * @offsetp: Returns the offset number within this device
 * @gpiop: Returns the absolute GPIO number, numbered from 0
 */
int gpio_lookup_name(const char *name, struct udevice **devp,
		     unsigned int *offsetp, unsigned int *gpiop);

/**
 * get_gpios() - Turn the values of a list of GPIOs into an integer
 *
 * This puts the value of the first GPIO into bit 0, the second into bit 1,
 * etc. then returns the resulting integer.
 *
 * @gpio_list: List of GPIOs to collect
 * @return resulting integer value
 */
unsigned gpio_get_values_as_int(const int *gpio_list);

#endif	/* _ASM_GENERIC_GPIO_H_ */