Newer
Older
/*
* Copyright 2012 Freescale Semiconductor, Inc.
* Andy Fleming <afleming@freescale.com>
* Roy Zang <tie-fei.zang@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
* Some part is taken from tsec.c
*/
#include <common.h>
#include <miiphy.h>
#include <phy.h>
#include <asm/io.h>
#include <asm/fsl_memac.h>
#include <fm_eth.h>
/*
* Write value to the PHY for this device to the register at regnum, waiting
* until the write is done before it returns. All PHY configuration has to be
* done through the TSEC1 MIIM regs
*/
int memac_mdio_write(struct mii_dev *bus, int port_addr, int dev_addr,
int regnum, u16 value)
{
u32 mdio_ctl;
struct memac_mdio_controller *regs = bus->priv;
u32 c45 = 1; /* Default to 10G interface */
if (dev_addr == MDIO_DEVAD_NONE) {
c45 = 0; /* clause 22 */
dev_addr = regnum & 0x1f;
clrbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
} else {
setbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
setbits_be32(®s->mdio_stat, MDIO_STAT_HOLD_15_CLK);
}
/* Wait till the bus is free */
while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
;
/* Set the port and dev addr */
mdio_ctl = MDIO_CTL_PORT_ADDR(port_addr) | MDIO_CTL_DEV_ADDR(dev_addr);
out_be32(®s->mdio_ctl, mdio_ctl);
/* Set the register address */
if (c45)
out_be32(®s->mdio_addr, regnum & 0xffff);
/* Wait till the bus is free */
while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
;
/* Write the value to the register */
out_be32(®s->mdio_data, MDIO_DATA(value));
/* Wait till the MDIO write is complete */
while ((in_be32(®s->mdio_data)) & MDIO_DATA_BSY)
;
return 0;
}
/*
* Reads from register regnum in the PHY for device dev, returning the value.
* Clears miimcom first. All PHY configuration has to be done through the
* TSEC1 MIIM regs
*/
int memac_mdio_read(struct mii_dev *bus, int port_addr, int dev_addr,
int regnum)
{
u32 mdio_ctl;
struct memac_mdio_controller *regs = bus->priv;
u32 c45 = 1;
if (dev_addr == MDIO_DEVAD_NONE) {
c45 = 0; /* clause 22 */
dev_addr = regnum & 0x1f;
clrbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
} else {
setbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
setbits_be32(®s->mdio_stat, MDIO_STAT_HOLD_15_CLK);
}
/* Wait till the bus is free */
while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
;
/* Set the Port and Device Addrs */
mdio_ctl = MDIO_CTL_PORT_ADDR(port_addr) | MDIO_CTL_DEV_ADDR(dev_addr);
out_be32(®s->mdio_ctl, mdio_ctl);
/* Set the register address */
if (c45)
out_be32(®s->mdio_addr, regnum & 0xffff);
/* Wait till the bus is free */
while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
;
/* Initiate the read */
mdio_ctl |= MDIO_CTL_READ;
out_be32(®s->mdio_ctl, mdio_ctl);
/* Wait till the MDIO write is complete */
while ((in_be32(®s->mdio_data)) & MDIO_DATA_BSY)
;
/* Return all Fs if nothing was there */
if (in_be32(®s->mdio_stat) & MDIO_STAT_RD_ER)
return 0xffff;
return in_be32(®s->mdio_data) & 0xffff;
}
int memac_mdio_reset(struct mii_dev *bus)
{
return 0;
}
int fm_memac_mdio_init(bd_t *bis, struct memac_mdio_info *info)
{
struct mii_dev *bus = mdio_alloc();
if (!bus) {
printf("Failed to allocate FM TGEC MDIO bus\n");
return -1;
}
bus->read = memac_mdio_read;
bus->write = memac_mdio_write;
bus->reset = memac_mdio_reset;
sprintf(bus->name, info->name);
bus->priv = info->regs;
/*
* On some platforms like B4860, default value of MDIO_CLK_DIV bits
* in mdio_stat(mdio_cfg) register generates MDIO clock too high
* (much higher than 2.5MHz), violating the IEEE specs.
* On other platforms like T1040, default value of MDIO_CLK_DIV bits
* is zero, so MDIO clock is disabled.
* So, for proper functioning of MDIO, MDIO_CLK_DIV bits needs to
* be properly initialized.
*/
setbits_be32(&((struct memac_mdio_controller *)info->regs)->mdio_stat,
MDIO_STAT_CLKDIV(258));