Newer
Older
/* Initializes CPU and basic hardware such as memory
* controllers, IRQ controller and system timer 0.
*
* (C) Copyright 2007
* Daniel Hellstrom, Gaisler Research, daniel@gaisler.com
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/asi.h>
#include <asm/leon.h>
#include <config.h>
#define TIMER_BASE_CLK 1000000
#define US_PER_TICK (1000000 / CONFIG_SYS_HZ)
DECLARE_GLOBAL_DATA_PTR;
/* reset CPU (jump to 0, without reset) */
void start(void);
struct {
gd_t gd_area;
bd_t bd;
} global_data;
/*
* Breath some life into the CPU...
*
* Set up the memory map,
* initialize a bunch of registers.
*
* Run from FLASH/PROM:
* - until memory controller is set up, only registers available
* - no global variables available for writing
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
*/
void cpu_init_f(void)
{
LEON2_regs *leon2 = (LEON2_regs *) LEON2_PREGS;
/* initialize the IRQMP */
leon2->Interrupt_Force = 0;
leon2->Interrupt_Pending = 0;
leon2->Interrupt_Clear = 0xfffe; /* clear all old pending interrupts */
leon2->Interrupt_Mask = 0xfffe0000; /* mask all IRQs */
/* cache */
/* I/O port setup */
#ifdef LEON2_IO_PORT_DIR
leon2->PIO_Direction = LEON2_IO_PORT_DIR;
#endif
#ifdef LEON2_IO_PORT_DATA
leon2->PIO_Data = LEON2_IO_PORT_DATA;
#endif
#ifdef LEON2_IO_PORT_INT
leon2->PIO_Interrupt = LEON2_IO_PORT_INT;
#else
leon2->PIO_Interrupt = 0;
#endif
}
void cpu_init_f2(void)
{
}
/*
* initialize higher level parts of CPU like time base and timers
*/
int cpu_init_r(void)
{
LEON2_regs *leon2 = (LEON2_regs *) LEON2_PREGS;
/* initialize prescaler common to all timers to 1MHz */
leon2->Scaler_Counter = leon2->Scaler_Reload =
(((CONFIG_SYS_CLK_FREQ / 1000) + 500) / 1000) - 1;
return (0);
}
/* Uses Timer 0 to get accurate
* pauses. Max 2 raised to 32 ticks
*
*/
void cpu_wait_ticks(unsigned long ticks)
{
unsigned long start = get_timer(0);
while (get_timer(start) < ticks) ;
}
/* initiate and setup timer0 interrupt to configured HZ. Base clock is 1MHz.
* Return irq number for timer int or a negative number for
* dealing with self
*/
int timer_interrupt_init_cpu(void)
{
LEON2_regs *leon2 = (LEON2_regs *) LEON2_PREGS;
/* SYS_HZ ticks per second */
leon2->Timer_Counter_1 = 0;
leon2->Timer_Reload_1 = (TIMER_BASE_CLK / CONFIG_SYS_HZ) - 1;
leon2->Timer_Control_1 =
(LEON2_TIMER_CTRL_EN | LEON2_TIMER_CTRL_RS | LEON2_TIMER_CTRL_LD);
return LEON2_TIMER1_IRQNO;
}
ulong get_tbclk(void)
{
return TIMER_BASE_CLK;
}
/*
* This function is intended for SHORT delays only.
*/
unsigned long cpu_usec2ticks(unsigned long usec)
{
if (usec < US_PER_TICK)
return usec / US_PER_TICK;
}
unsigned long cpu_ticks2usec(unsigned long ticks)
{
return ticks * US_PER_TICK;