diff --git a/.travis.yml b/.travis.yml
index d7094e325a8da395818199f34f12421b8ce116b6..891528472e1ed094138781ec605f8e4032507a1b 100644
--- a/.travis.yml
+++ b/.travis.yml
@@ -217,8 +217,6 @@ matrix:
- BUILDMAN="corenet_ds b4860qds sbc8548 bsc91*"
- env:
- BUILDMAN="mpc86xx"
- - env:
- - BUILDMAN="mpc8xx"
- env:
- BUILDMAN="siemens"
- env:
diff --git a/README b/README
index a4a9c3b4eccf34e40530de76688af6b5cf2193ed..4819696deb64d0b34b1b3fac1337b456662733f7 100644
--- a/README
+++ b/README
@@ -328,34 +328,6 @@ The following options need to be configured:
multiple fs option at one time
for marvell soc family
-- 8xx CPU Options: (if using an MPC8xx CPU)
- CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
- get_gclk_freq() cannot work
- e.g. if there is no 32KHz
- reference PIT/RTC clock
- CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
- or XTAL/EXTAL)
-
-- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
- CONFIG_SYS_8xx_CPUCLK_MIN
- CONFIG_SYS_8xx_CPUCLK_MAX
- CONFIG_8xx_CPUCLK_DEFAULT
- See doc/README.MPC866
-
- CONFIG_SYS_MEASURE_CPUCLK
-
- Define this to measure the actual CPU clock instead
- of relying on the correctness of the configured
- values. Mostly useful for board bringup to make sure
- the PLL is locked at the intended frequency. Note
- that this requires a (stable) reference clock (32 kHz
- RTC clock or CONFIG_SYS_8XX_XIN)
-
- CONFIG_SYS_DELAYED_ICACHE
-
- Define this option if you want to enable the
- ICache only when Code runs from RAM.
-
- 85xx CPU Options:
CONFIG_SYS_PPC64
@@ -723,26 +695,15 @@ The following options need to be configured:
Define this variable to enable hw flow control in serial driver.
Current user of this option is drivers/serial/nsl16550.c driver
-- Console Interface:
- Depending on board, define exactly one serial port
- (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
- CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
- console by defining CONFIG_8xx_CONS_NONE
-
- Note: if CONFIG_8xx_CONS_NONE is defined, the serial
- port routines must be defined elsewhere
- (i.e. serial_init(), serial_getc(), ...)
-
- Console Baudrate:
CONFIG_BAUDRATE - in bps
Select one of the baudrates listed in
CONFIG_SYS_BAUDRATE_TABLE, see below.
- CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
- Console Rx buffer length
With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
the maximum receive buffer length for the SMC.
- This option is actual only for 82xx and 8xx possible.
+ This option is actual only for 82xx possible.
If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
must be defined, to setup the maximum idle timeout for
the SMC.
@@ -912,7 +873,7 @@ The following options need to be configured:
Note: Don't enable the "icache" and "dcache" commands
(configuration option CONFIG_CMD_CACHE) unless you know
what you (and your U-Boot users) are doing. Data
- cache cannot be enabled on systems like the 8xx or
+ cache cannot be enabled on systems like the
8260 (where accesses to the IMMR region must be
uncached), and it cannot be disabled on all other
systems where we (mis-) use the data cache to hold an
@@ -976,7 +937,7 @@ The following options need to be configured:
CONFIG_WATCHDOG
If this variable is defined, it enables watchdog
support for the SoC. There must be support in the SoC
- specific code for a watchdog. For the 8xx and 8260
+ specific code for a watchdog. For the 8260
CPUs, the SIU Watchdog feature is enabled in the SYPCR
register. When supported for a specific SoC is
available, then no further board specific code should
@@ -1004,7 +965,6 @@ The following options need to be configured:
has to be selected, too. Define exactly one of the
following options:
- CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
@@ -1345,11 +1305,6 @@ The following options need to be configured:
Define this if you want stdin, stdout &/or stderr to
be set to usbtty.
- mpc8xx:
- CONFIG_SYS_USB_EXTC_CLK 0xBLAH
- Derive USB clock from external clock "blah"
- - CONFIG_SYS_USB_EXTC_CLK 0x02
-
If you have a USB-IF assigned VendorID then you may wish to
define your own vendor specific values either in BoardName.h
or directly in usbd_vendor_info.h. If you don't define
@@ -1953,7 +1908,7 @@ The following options need to be configured:
Defining CONFIG_CAN_DRIVER enables CAN driver support
on those systems that support this (optional)
- feature, like the TQM8xxL modules.
+ feature.
- I2C Support: CONFIG_SYS_I2C
@@ -2445,7 +2400,7 @@ The following options need to be configured:
following board configurations are known to be
"pRAM-clean":
- IVMS8, IVML24, SPD8xx, TQM8xxL,
+ IVMS8, IVML24, SPD8xx,
HERMES, IP860, RPXlite, LWMON,
FLAGADM, TQM8260
@@ -4048,7 +4003,7 @@ Low Level (hardware related) configuration options:
- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
DO NOT CHANGE unless you know exactly what you're
- doing! (11-4) [MPC8xx/82xx systems only]
+ doing! (11-4) [82xx systems only]
- CONFIG_SYS_INIT_RAM_ADDR:
@@ -4061,7 +4016,7 @@ Low Level (hardware related) configuration options:
sequences.
U-Boot uses the following memory types:
- - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
+ - MPC8260: IMMR (internal memory of the CPU)
- MPC824X: data cache
- PPC4xx: data cache
@@ -4119,19 +4074,7 @@ Low Level (hardware related) configuration options:
Machine Mode Register and Memory Periodic Timer
Prescaler definitions (SDRAM timing)
-- CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
- enable I2C microcode relocation patch (MPC8xx);
- define relocation offset in DPRAM [DSP2]
-
-- CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
- enable SMC microcode relocation patch (MPC8xx);
- define relocation offset in DPRAM [SMC1]
-
-- CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
- enable SPI microcode relocation patch (MPC8xx);
- define relocation offset in DPRAM [SCC4]
-
-- CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
+- CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8260 only)
Offset of the bootmode word in DPRAM used by post
(Power On Self Tests). This definition overrides
#define'd default value in commproc.h resp.
@@ -4225,21 +4168,6 @@ Low Level (hardware related) configuration options:
Only for 83xx systems. If specified, then DDR should
be configured using CS0 and CS1 instead of CS2 and CS3.
-- CONFIG_ETHER_ON_FEC[12]
- Define to enable FEC[12] on a 8xx series processor.
-
-- CONFIG_FEC[12]_PHY
- Define to the hardcoded PHY address which corresponds
- to the given FEC; i. e.
- #define CONFIG_FEC1_PHY 4
- means that the PHY with address 4 is connected to FEC1
-
- When set to -1, means to probe for first available.
-
-- CONFIG_FEC[12]_PHY_NORXERR
- The PHY does not have a RXERR line (RMII only).
- (so program the FEC to ignore it).
-
- CONFIG_RMII
Enable RMII mode for all FECs.
Note that this is a global option, we can't
diff --git a/api/api_platform-powerpc.c b/api/api_platform-powerpc.c
index f23f17501fa03c34b06d9fc22b8a754a9845dc1a..71fea5a75acbda15c3c3a27d93847a3bebe7bd31 100644
--- a/api/api_platform-powerpc.c
+++ b/api/api_platform-powerpc.c
@@ -30,7 +30,7 @@ int platform_sys_info(struct sys_info *si)
si->clk_bus = gd->bus_clk;
si->clk_cpu = gd->cpu_clk;
-#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || defined(CONFIG_MPC8260) || \
+#if defined(CONFIG_5xx) || defined(CONFIG_MPC8260) || \
defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
#define bi_bar bi_immr_base
#elif defined(CONFIG_MPC5xxx)
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index f37a9cbffb9b01c9db5db40896693ea0c6959739..671d2cc0cf7896c4b8ef226bbd7964b94894da05 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -41,9 +41,6 @@ config MPC86xx
select SYS_FSL_DDR
select SYS_FSL_DDR_BE
-config 8xx
- bool "MPC8xx"
-
config 4xx
bool "PPC4xx"
select CREATE_ARCH_SYMLINK
@@ -60,7 +57,6 @@ source "arch/powerpc/cpu/mpc8260/Kconfig"
source "arch/powerpc/cpu/mpc83xx/Kconfig"
source "arch/powerpc/cpu/mpc85xx/Kconfig"
source "arch/powerpc/cpu/mpc86xx/Kconfig"
-source "arch/powerpc/cpu/mpc8xx/Kconfig"
source "arch/powerpc/cpu/ppc4xx/Kconfig"
endmenu
diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig
deleted file mode 100644
index 79cee35fb1277d4038df81ebf74db1e1bff00a70..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/Kconfig
+++ /dev/null
@@ -1,51 +0,0 @@
-menu "mpc8xx CPU"
- depends on 8xx
-
-config SYS_CPU
- default "mpc8xx"
-
-choice
- prompt "Target select"
- optional
-
-config TARGET_TQM823L
- bool "Support TQM823L"
-
-config TARGET_TQM823M
- bool "Support TQM823M"
-
-config TARGET_TQM850L
- bool "Support TQM850L"
-
-config TARGET_TQM850M
- bool "Support TQM850M"
-
-config TARGET_TQM855L
- bool "Support TQM855L"
-
-config TARGET_TQM855M
- bool "Support TQM855M"
-
-config TARGET_TQM860L
- bool "Support TQM860L"
-
-config TARGET_TQM860M
- bool "Support TQM860M"
-
-config TARGET_TQM862L
- bool "Support TQM862L"
-
-config TARGET_TQM862M
- bool "Support TQM862M"
-
-config TARGET_TQM866M
- bool "Support TQM866M"
-
-config TARGET_TQM885D
- bool "Support TQM885D"
-
-endchoice
-
-source "board/tqc/tqm8xx/Kconfig"
-
-endmenu
diff --git a/arch/powerpc/cpu/mpc8xx/Makefile b/arch/powerpc/cpu/mpc8xx/Makefile
deleted file mode 100644
index fc91a054f0e029123db3896623f04a1080f52a1d..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/Makefile
+++ /dev/null
@@ -1,25 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-# ccflags-y += -DET_DEBUG
-
-extra-y += start.o
-extra-y += traps.o
-obj-y += bedbug_860.o
-obj-y += cpu.o
-obj-y += cpu_init.o
-obj-y += fec.o
-obj-$(CONFIG_OF_LIBFDT) += fdt.o
-obj-y += interrupts.o
-obj-y += scc.o
-obj-y += serial.o
-obj-y += speed.o
-obj-y += spi.o
-obj-y += upatch.o
-obj-y += video.o
-obj-y += kgdb.o
-obj-y += plprcr_write.o
diff --git a/arch/powerpc/cpu/mpc8xx/bedbug_860.c b/arch/powerpc/cpu/mpc8xx/bedbug_860.c
deleted file mode 100644
index c0016f72ff2be066c64a3eaa8d80806f8ec33c20..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/bedbug_860.c
+++ /dev/null
@@ -1,314 +0,0 @@
-/*
- * Bedbug Functions specific to the MPC860 chip
- */
-
-#include <common.h>
-#include <command.h>
-#include <linux/ctype.h>
-#include <bedbug/bedbug.h>
-#include <bedbug/regs.h>
-#include <bedbug/ppc.h>
-#include <bedbug/type.h>
-
-#if defined(CONFIG_CMD_BEDBUG) && defined(CONFIG_8xx)
-
-#define MAX_BREAK_POINTS 2
-
-extern CPU_DEBUG_CTX bug_ctx;
-
-void bedbug860_init __P((void));
-void bedbug860_do_break __P((cmd_tbl_t*,int,int,char*const[]));
-void bedbug860_break_isr __P((struct pt_regs*));
-int bedbug860_find_empty __P((void));
-int bedbug860_set __P((int,unsigned long));
-int bedbug860_clear __P((int));
-
-
-/* ======================================================================
- * Initialize the global bug_ctx structure for the MPC860. Clear all
- * of the breakpoints.
- * ====================================================================== */
-
-void bedbug860_init( void )
-{
- int i;
- /* -------------------------------------------------- */
-
- bug_ctx.hw_debug_enabled = 0;
- bug_ctx.stopped = 0;
- bug_ctx.current_bp = 0;
- bug_ctx.regs = NULL;
-
- bug_ctx.do_break = bedbug860_do_break;
- bug_ctx.break_isr = bedbug860_break_isr;
- bug_ctx.find_empty = bedbug860_find_empty;
- bug_ctx.set = bedbug860_set;
- bug_ctx.clear = bedbug860_clear;
-
- for( i = 1; i <= MAX_BREAK_POINTS; ++i )
- (*bug_ctx.clear)( i );
-
- puts ("BEDBUG:ready\n");
- return;
-} /* bedbug_init_breakpoints */
-
-
-
-/* ======================================================================
- * Set/clear/show one of the hardware breakpoints for the 860. The "off"
- * string will disable a specific breakpoint. The "show" string will
- * display the current breakpoints. Otherwise an address will set a
- * breakpoint at that address. Setting a breakpoint uses the CPU-specific
- * set routine which will assign a breakpoint number.
- * ====================================================================== */
-
-void bedbug860_do_break (cmd_tbl_t *cmdtp, int flag, int argc,
- char * const argv[])
-{
- long addr = 0; /* Address to break at */
- int which_bp; /* Breakpoint number */
- /* -------------------------------------------------- */
-
- if (argc < 2) {
- cmd_usage(cmdtp);
- return;
- }
-
- /* Turn off a breakpoint */
-
- if( strcmp( argv[ 1 ], "off" ) == 0 )
- {
- if( bug_ctx.hw_debug_enabled == 0 )
- {
- printf( "No breakpoints enabled\n" );
- return;
- }
-
- which_bp = simple_strtoul( argv[ 2 ], NULL, 10 );
-
- if( bug_ctx.clear )
- (*bug_ctx.clear)( which_bp );
-
- printf( "Breakpoint %d removed\n", which_bp );
- return;
- }
-
- /* Show a list of breakpoints */
-
- if( strcmp( argv[ 1 ], "show" ) == 0 )
- {
- for( which_bp = 1; which_bp <= MAX_BREAK_POINTS; ++which_bp )
- {
-
- switch( which_bp )
- {
- case 1: addr = GET_CMPA(); break;
- case 2: addr = GET_CMPB(); break;
- case 3: addr = GET_CMPC(); break;
- case 4: addr = GET_CMPD(); break;
- }
-
- printf( "Breakpoint [%d]: ", which_bp );
- if( addr == 0 )
- printf( "NOT SET\n" );
- else
- disppc( (unsigned char *)addr, 0, 1, bedbug_puts, F_RADHEX );
- }
- return;
- }
-
- /* Set a breakpoint at the address */
-
- if( !isdigit( argv[ 1 ][ 0 ])) {
- cmd_usage(cmdtp);
- return;
- }
-
- addr = simple_strtoul( argv[ 1 ], NULL, 16 ) & 0xfffffffc;
-
- if(( bug_ctx.set ) && ( which_bp = (*bug_ctx.set)( 0, addr )) > 0 )
- {
- printf( "Breakpoint [%d]: ", which_bp );
- disppc( (unsigned char *)addr, 0, 1, bedbug_puts, F_RADHEX );
- }
-
- return;
-} /* bedbug860_do_break */
-
-
-
-/* ======================================================================
- * Handle a breakpoint. First determine which breakpoint was hit by
- * looking at the DeBug Status Register (DBSR), clear the breakpoint
- * and enter a mini main loop. Stay in the loop until the stopped flag
- * in the debug context is cleared.
- * ====================================================================== */
-
-void bedbug860_break_isr( struct pt_regs *regs )
-{
- unsigned long addr; /* Address stopped at */
- unsigned long cause; /* Address stopped at */
- /* -------------------------------------------------- */
-
- cause = GET_ICR();
-
- if( !(cause & 0x00000004)) {
- printf( "Not an instruction breakpoint (ICR 0x%08lx)\n", cause );
- return;
- }
-
- addr = regs->nip;
-
- if( addr == GET_CMPA() )
- {
- bug_ctx.current_bp = 1;
- }
- else if( addr == GET_CMPB() )
- {
- bug_ctx.current_bp = 2;
- }
- else if( addr == GET_CMPC() )
- {
- bug_ctx.current_bp = 3;
- }
- else if( addr == GET_CMPD() )
- {
- bug_ctx.current_bp = 4;
- }
-
- bedbug_main_loop( addr, regs );
- return;
-} /* bedbug860_break_isr */
-
-
-
-/* ======================================================================
- * Look through all of the hardware breakpoints available to see if one
- * is unused.
- * ====================================================================== */
-
-int bedbug860_find_empty( void )
-{
- /* -------------------------------------------------- */
-
- if( GET_CMPA() == 0 )
- return 1;
-
- if( GET_CMPB() == 0 )
- return 2;
-
- if( GET_CMPC() == 0 )
- return 3;
-
- if( GET_CMPD() == 0 )
- return 4;
-
- return 0;
-} /* bedbug860_find_empty */
-
-
-
-/* ======================================================================
- * Set a breakpoint. If 'which_bp' is zero then find an unused breakpoint
- * number, otherwise reassign the given breakpoint. If hardware debugging
- * is not enabled, then turn it on via the MSR and DBCR0. Set the break
- * address in the appropriate IACx register and enable proper address
- * beakpoint in DBCR0.
- * ====================================================================== */
-
-int bedbug860_set( int which_bp, unsigned long addr )
-{
- /* -------------------------------------------------- */
-
- /* Only look if which_bp == 0, else use which_bp */
- if(( bug_ctx.find_empty ) && ( !which_bp ) &&
- ( which_bp = (*bug_ctx.find_empty)()) == 0 )
- {
- printf( "All breakpoints in use\n" );
- return 0;
- }
-
- if( which_bp < 1 || which_bp > MAX_BREAK_POINTS )
- {
- printf( "Invalid break point # %d\n", which_bp );
- return 0;
- }
-
- if( ! bug_ctx.hw_debug_enabled )
- {
- bug_ctx.hw_debug_enabled = 1;
- SET_DER( GET_DER() | 0x00000004 );
- }
-
- switch( which_bp )
- {
- case 1:
- SET_CMPA( addr );
- SET_ICTRL( GET_ICTRL() | 0x80080800 ); /* CTA=Equal,IW0=Match A,SIW0EN */
- break;
-
- case 2:
- SET_CMPB( addr );
- SET_ICTRL( GET_ICTRL() | 0x10020400 ); /* CTB=Equal,IW1=Match B,SIW1EN */
- break;
-
- case 3:
- SET_CMPC( addr );
- SET_ICTRL( GET_ICTRL() | 0x02008200 ); /* CTC=Equal,IW2=Match C,SIW2EN */
- break;
-
- case 4:
- SET_CMPD( addr );
- SET_ICTRL( GET_ICTRL() | 0x00404100 ); /* CTD=Equal,IW3=Match D,SIW3EN */
- break;
- }
-
- return which_bp;
-} /* bedbug860_set */
-
-
-
-/* ======================================================================
- * Disable a specific breakoint by setting the appropriate IACx register
- * to zero and claring the instruction address breakpoint in DBCR0.
- * ====================================================================== */
-
-int bedbug860_clear( int which_bp )
-{
- /* -------------------------------------------------- */
-
- if( which_bp < 1 || which_bp > MAX_BREAK_POINTS )
- {
- printf( "Invalid break point # (%d)\n", which_bp );
- return -1;
- }
-
- switch( which_bp )
- {
- case 1:
- SET_CMPA( 0 );
- SET_ICTRL( GET_ICTRL() & ~0x80080800 ); /* CTA=Equal,IW0=Match A,SIW0EN */
- break;
-
- case 2:
- SET_CMPB( 0 );
- SET_ICTRL( GET_ICTRL() & ~0x10020400 ); /* CTB=Equal,IW1=Match B,SIW1EN */
- break;
-
- case 3:
- SET_CMPC( 0 );
- SET_ICTRL( GET_ICTRL() & ~0x02008200 ); /* CTC=Equal,IW2=Match C,SIW2EN */
- break;
-
- case 4:
- SET_CMPD( 0 );
- SET_ICTRL( GET_ICTRL() & ~0x00404100 ); /* CTD=Equal,IW3=Match D,SIW3EN */
- break;
- }
-
- return 0;
-} /* bedbug860_clear */
-
-
-/* ====================================================================== */
-#endif
diff --git a/arch/powerpc/cpu/mpc8xx/config.mk b/arch/powerpc/cpu/mpc8xx/config.mk
deleted file mode 100644
index 485e43d2de3cf95ac846ab3f9c73d84cd0217be8..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/config.mk
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2010
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-PLATFORM_CPPFLAGS += -mstring -mcpu=860 -msoft-float
diff --git a/arch/powerpc/cpu/mpc8xx/cpu.c b/arch/powerpc/cpu/mpc8xx/cpu.c
deleted file mode 100644
index 105be9ccc7e16e7a0b93b51fb199392c4d8b8d87..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/cpu.c
+++ /dev/null
@@ -1,580 +0,0 @@
-/*
- * (C) Copyright 2000-2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * m8xx.c
- *
- * CPU specific code
- *
- * written or collected and sometimes rewritten by
- * Magnus Damm <damm@bitsmart.com>
- *
- * minor modifications by
- * Wolfgang Denk <wd@denx.de>
- */
-
-#include <common.h>
-#include <watchdog.h>
-#include <command.h>
-#include <mpc8xx.h>
-#include <commproc.h>
-#include <netdev.h>
-#include <asm/cache.h>
-#include <linux/compiler.h>
-#include <asm/io.h>
-
-#if defined(CONFIG_OF_LIBFDT)
-#include <libfdt.h>
-#include <fdt_support.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static char *cpu_warning = "\n " \
- "*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***";
-
-#if ((defined(CONFIG_MPC86x) || defined(CONFIG_MPC855)) && \
- !defined(CONFIG_MPC862))
-
-static int check_CPU (long clock, uint pvr, uint immr)
-{
- char *id_str =
-# if defined(CONFIG_MPC855)
- "PC855";
-# elif defined(CONFIG_MPC860P)
- "PC860P";
-# else
- NULL;
-# endif
- volatile immap_t *immap = (immap_t *) (immr & 0xFFFF0000);
- uint k, m;
- char buf[32];
- char pre = 'X';
- char *mid = "xx";
- char *suf;
-
- /* the highest 16 bits should be 0x0050 for a 860 */
-
- if ((pvr >> 16) != 0x0050)
- return -1;
-
- k = (immr << 16) |
- immap->im_cpm.cp_dparam16[PROFF_REVNUM / sizeof(u16)];
- m = 0;
- suf = "";
-
- /*
- * Some boards use sockets so different CPUs can be used.
- * We have to check chip version in run time.
- */
- switch (k) {
- case 0x00020001: pre = 'P'; break;
- case 0x00030001: break;
- case 0x00120003: suf = "A"; break;
- case 0x00130003: suf = "A3"; break;
-
- case 0x00200004: suf = "B"; break;
-
- case 0x00300004: suf = "C"; break;
- case 0x00310004: suf = "C1"; m = 1; break;
-
- case 0x00200064: mid = "SR"; suf = "B"; break;
- case 0x00300065: mid = "SR"; suf = "C"; break;
- case 0x00310065: mid = "SR"; suf = "C1"; m = 1; break;
- case 0x05010000: suf = "D3"; m = 1; break;
- case 0x05020000: suf = "D4"; m = 1; break;
- /* this value is not documented anywhere */
- case 0x40000000: pre = 'P'; suf = "D"; m = 1; break;
- /* MPC866P/MPC866T/MPC859T/MPC859DSL/MPC852T */
- case 0x08010004: /* Rev. A.0 */
- suf = "A";
- /* fall through */
- case 0x08000003: /* Rev. 0.3 */
- pre = 'M'; m = 1;
- if (id_str == NULL)
- id_str =
-# if defined(CONFIG_MPC859T)
- "PC859T";
-# else
- "PC866x"; /* Unknown chip from MPC866 family */
-# endif
- break;
- case 0x09000000: pre = 'M'; mid = suf = ""; m = 1;
- if (id_str == NULL)
- id_str = "PC885"; /* 870/875/880/885 */
- break;
-
- default: suf = NULL; break;
- }
-
- if (id_str == NULL)
- id_str = "PC86x"; /* Unknown 86x chip */
- if (suf)
- printf ("%c%s%sZPnn%s", pre, id_str, mid, suf);
- else
- printf ("unknown M%s (0x%08x)", id_str, k);
-
-
-#if defined(CONFIG_SYS_8xx_CPUCLK_MIN) && defined(CONFIG_SYS_8xx_CPUCLK_MAX)
- printf (" at %s MHz [%d.%d...%d.%d MHz]\n ",
- strmhz (buf, clock),
- CONFIG_SYS_8xx_CPUCLK_MIN / 1000000,
- ((CONFIG_SYS_8xx_CPUCLK_MIN % 1000000) + 50000) / 100000,
- CONFIG_SYS_8xx_CPUCLK_MAX / 1000000,
- ((CONFIG_SYS_8xx_CPUCLK_MAX % 1000000) + 50000) / 100000
- );
-#else
- printf (" at %s MHz: ", strmhz (buf, clock));
-#endif
- print_size(checkicache(), " I-Cache ");
- print_size(checkdcache(), " D-Cache");
-
- /* do we have a FEC (860T/P or 852/859/866/885)? */
-
- immap->im_cpm.cp_fec.fec_addr_low = 0x12345678;
- if (immap->im_cpm.cp_fec.fec_addr_low == 0x12345678) {
- printf (" FEC present");
- }
-
- if (!m) {
- puts (cpu_warning);
- }
-
- putc ('\n');
-
-#ifdef DEBUG
- if(clock != measure_gclk()) {
- printf ("clock %ldHz != %dHz\n", clock, measure_gclk());
- }
-#endif
-
- return 0;
-}
-
-#elif defined(CONFIG_MPC862)
-
-static int check_CPU (long clock, uint pvr, uint immr)
-{
- volatile immap_t *immap = (immap_t *) (immr & 0xFFFF0000);
- uint k, m;
- char buf[32];
- char pre = 'X';
- __maybe_unused char *mid = "xx";
- char *suf;
-
- /* the highest 16 bits should be 0x0050 for a 8xx */
-
- if ((pvr >> 16) != 0x0050)
- return -1;
-
- k = (immr << 16) |
- immap->im_cpm.cp_dparam16[PROFF_REVNUM / sizeof(u16)];
- m = 0;
-
- switch (k) {
-
- /* this value is not documented anywhere */
- case 0x06000000: mid = "P"; suf = "0"; break;
- case 0x06010001: mid = "P"; suf = "A"; m = 1; break;
- case 0x07000003: mid = "P"; suf = "B"; m = 1; break;
- default: suf = NULL; break;
- }
-
-#ifndef CONFIG_MPC857
- if (suf)
- printf ("%cPC862%sZPnn%s", pre, mid, suf);
- else
- printf ("unknown MPC862 (0x%08x)", k);
-#else
- if (suf)
- printf ("%cPC857TZPnn%s", pre, suf); /* only 857T tested right now! */
- else
- printf ("unknown MPC857 (0x%08x)", k);
-#endif
-
- printf(" at %s MHz: ", strmhz(buf, clock));
-
- print_size(checkicache(), " I-Cache ");
- print_size(checkdcache(), " D-Cache");
-
- /* lets check and see if we're running on a 862T (or P?) */
-
- immap->im_cpm.cp_fec.fec_addr_low = 0x12345678;
- if (immap->im_cpm.cp_fec.fec_addr_low == 0x12345678) {
- printf (" FEC present");
- }
-
- if (!m) {
- puts (cpu_warning);
- }
-
- putc ('\n');
-
- return 0;
-}
-
-#elif defined(CONFIG_MPC823)
-
-static int check_CPU (long clock, uint pvr, uint immr)
-{
- volatile immap_t *immap = (immap_t *) (immr & 0xFFFF0000);
- uint k, m;
- char buf[32];
- char *suf;
-
- /* the highest 16 bits should be 0x0050 for a 8xx */
-
- if ((pvr >> 16) != 0x0050)
- return -1;
-
- k = (immr << 16) |
- in_be16(&immap->im_cpm.cp_dparam16[PROFF_REVNUM / sizeof(u16)]);
- m = 0;
-
- switch (k) {
- /* MPC823 */
- case 0x20000000: suf = "0"; break;
- case 0x20010000: suf = "0.1"; break;
- case 0x20020000: suf = "Z2/3"; break;
- case 0x20020001: suf = "Z3"; break;
- case 0x21000000: suf = "A"; break;
- case 0x21010000: suf = "B"; m = 1; break;
- case 0x21010001: suf = "B2"; m = 1; break;
- /* MPC823E */
- case 0x24010000: suf = NULL;
- puts ("PPC823EZTnnB2");
- m = 1;
- break;
- default:
- suf = NULL;
- printf ("unknown MPC823 (0x%08x)", k);
- break;
- }
- if (suf)
- printf ("PPC823ZTnn%s", suf);
-
- printf(" at %s MHz: ", strmhz(buf, clock));
-
- print_size(checkicache(), " I-Cache ");
- print_size(checkdcache(), " D-Cache");
-
- /* lets check and see if we're running on a 860T (or P?) */
-
- immap->im_cpm.cp_fec.fec_addr_low = 0x12345678;
- if (immap->im_cpm.cp_fec.fec_addr_low == 0x12345678) {
- puts (" FEC present");
- }
-
- if (!m) {
- puts (cpu_warning);
- }
-
- putc ('\n');
-
- return 0;
-}
-
-#elif defined(CONFIG_MPC850)
-
-static int check_CPU (long clock, uint pvr, uint immr)
-{
- volatile immap_t *immap = (immap_t *) (immr & 0xFFFF0000);
- uint k, m;
- char buf[32];
-
- /* the highest 16 bits should be 0x0050 for a 8xx */
-
- if ((pvr >> 16) != 0x0050)
- return -1;
-
- k = (immr << 16) |
- immap->im_cpm.cp_dparam16[PROFF_REVNUM / sizeof(u16)];
- m = 0;
-
- switch (k) {
- case 0x20020001:
- printf ("XPC850xxZT");
- break;
- case 0x21000065:
- printf ("XPC850xxZTA");
- break;
- case 0x21010067:
- printf ("XPC850xxZTB");
- m = 1;
- break;
- case 0x21020068:
- printf ("XPC850xxZTC");
- m = 1;
- break;
- default:
- printf ("unknown MPC850 (0x%08x)", k);
- }
- printf(" at %s MHz: ", strmhz(buf, clock));
-
- print_size(checkicache(), " I-Cache ");
- print_size(checkdcache(), " D-Cache");
-
- /* lets check and see if we're running on a 850T (or P?) */
-
- immap->im_cpm.cp_fec.fec_addr_low = 0x12345678;
- if (immap->im_cpm.cp_fec.fec_addr_low == 0x12345678) {
- printf (" FEC present");
- }
-
- if (!m) {
- puts (cpu_warning);
- }
-
- putc ('\n');
-
- return 0;
-}
-#else
-#error CPU undefined
-#endif
-/* ------------------------------------------------------------------------- */
-
-int checkcpu (void)
-{
- ulong clock = gd->cpu_clk;
- uint immr = get_immr (0); /* Return full IMMR contents */
- uint pvr = get_pvr ();
-
- puts ("CPU: ");
-
- /* 850 has PARTNUM 20 */
- /* 801 has PARTNUM 10 */
- return check_CPU (clock, pvr, immr);
-}
-
-/* ------------------------------------------------------------------------- */
-/* L1 i-cache */
-/* the standard 860 has 128 sets of 16 bytes in 2 ways (= 4 kB) */
-/* the 860 P (plus) has 256 sets of 16 bytes in 4 ways (= 16 kB) */
-
-int checkicache (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- u32 cacheon = rd_ic_cst () & IDC_ENABLED;
-
-#ifdef CONFIG_IP86x
- u32 k = memctl->memc_br1 & ~0x00007fff; /* probe in flash memoryarea */
-#else
- u32 k = memctl->memc_br0 & ~0x00007fff; /* probe in flash memoryarea */
-#endif
- u32 m;
- u32 lines = -1;
-
- wr_ic_cst (IDC_UNALL);
- wr_ic_cst (IDC_INVALL);
- wr_ic_cst (IDC_DISABLE);
- __asm__ volatile ("isync");
-
- while (!((m = rd_ic_cst ()) & IDC_CERR2)) {
- wr_ic_adr (k);
- wr_ic_cst (IDC_LDLCK);
- __asm__ volatile ("isync");
-
- lines++;
- k += 0x10; /* the number of bytes in a cacheline */
- }
-
- wr_ic_cst (IDC_UNALL);
- wr_ic_cst (IDC_INVALL);
-
- if (cacheon)
- wr_ic_cst (IDC_ENABLE);
- else
- wr_ic_cst (IDC_DISABLE);
-
- __asm__ volatile ("isync");
-
- return lines << 4;
-};
-
-/* ------------------------------------------------------------------------- */
-/* L1 d-cache */
-/* the standard 860 has 128 sets of 16 bytes in 2 ways (= 4 kB) */
-/* the 860 P (plus) has 256 sets of 16 bytes in 2 ways (= 8 kB) */
-/* call with cache disabled */
-
-int checkdcache (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- u32 cacheon = rd_dc_cst () & IDC_ENABLED;
-
-#ifdef CONFIG_IP86x
- u32 k = memctl->memc_br1 & ~0x00007fff; /* probe in flash memoryarea */
-#else
- u32 k = memctl->memc_br0 & ~0x00007fff; /* probe in flash memoryarea */
-#endif
- u32 m;
- u32 lines = -1;
-
- wr_dc_cst (IDC_UNALL);
- wr_dc_cst (IDC_INVALL);
- wr_dc_cst (IDC_DISABLE);
-
- while (!((m = rd_dc_cst ()) & IDC_CERR2)) {
- wr_dc_adr (k);
- wr_dc_cst (IDC_LDLCK);
- lines++;
- k += 0x10; /* the number of bytes in a cacheline */
- }
-
- wr_dc_cst (IDC_UNALL);
- wr_dc_cst (IDC_INVALL);
-
- if (cacheon)
- wr_dc_cst (IDC_ENABLE);
- else
- wr_dc_cst (IDC_DISABLE);
-
- return lines << 4;
-};
-
-/* ------------------------------------------------------------------------- */
-
-void upmconfig (uint upm, uint * table, uint size)
-{
- uint i;
- uint addr = 0;
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- for (i = 0; i < size; i++) {
- memctl->memc_mdr = table[i]; /* (16-15) */
- memctl->memc_mcr = addr | upm; /* (16-16) */
- addr++;
- }
-}
-
-/* ------------------------------------------------------------------------- */
-
-int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- ulong msr, addr;
-
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- immap->im_clkrst.car_plprcr |= PLPRCR_CSR; /* Checkstop Reset enable */
-
- /* Interrupts and MMU off */
- __asm__ volatile ("mtspr 81, 0");
- __asm__ volatile ("mfmsr %0":"=r" (msr));
-
- msr &= ~0x1030;
- __asm__ volatile ("mtmsr %0"::"r" (msr));
-
- /*
- * Trying to execute the next instruction at a non-existing address
- * should cause a machine check, resulting in reset
- */
-#ifdef CONFIG_SYS_RESET_ADDRESS
- addr = CONFIG_SYS_RESET_ADDRESS;
-#else
- /*
- * note: when CONFIG_SYS_MONITOR_BASE points to a RAM address, CONFIG_SYS_MONITOR_BASE
- * - sizeof (ulong) is usually a valid address. Better pick an address
- * known to be invalid on your system and assign it to CONFIG_SYS_RESET_ADDRESS.
- * "(ulong)-1" used to be a good choice for many systems...
- */
- addr = CONFIG_SYS_MONITOR_BASE - sizeof (ulong);
-#endif
- ((void (*)(void)) addr) ();
- return 1;
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Get timebase clock frequency (like cpu_clk in Hz)
- *
- * See sections 14.2 and 14.6 of the User's Manual
- */
-unsigned long get_tbclk (void)
-{
- uint immr = get_immr (0); /* Return full IMMR contents */
- volatile immap_t *immap = (volatile immap_t *)(immr & 0xFFFF0000);
- ulong oscclk, factor, pll;
-
- if (immap->im_clkrst.car_sccr & SCCR_TBS) {
- return (gd->cpu_clk / 16);
- }
-
- pll = immap->im_clkrst.car_plprcr;
-
-#define PLPRCR_val(a) ((pll & PLPRCR_ ## a ## _MSK) >> PLPRCR_ ## a ## _SHIFT)
-
- /*
- * For newer PQ1 chips (MPC866/87x/88x families), PLL multiplication
- * factor is calculated as follows:
- *
- * MFN
- * MFI + -------
- * MFD + 1
- * factor = -----------------
- * (PDF + 1) * 2^S
- *
- * For older chips, it's just MF field of PLPRCR plus one.
- */
- if ((immr & 0x0FFF) >= MPC8xx_NEW_CLK) { /* MPC866/87x/88x series */
- factor = (PLPRCR_val(MFI) + PLPRCR_val(MFN)/(PLPRCR_val(MFD)+1))/
- (PLPRCR_val(PDF)+1) / (1<<PLPRCR_val(S));
- } else {
- factor = PLPRCR_val(MF)+1;
- }
-
- oscclk = gd->cpu_clk / factor;
-
- if ((immap->im_clkrst.car_sccr & SCCR_RTSEL) == 0 || factor > 2) {
- return (oscclk / 4);
- }
- return (oscclk / 16);
-}
-
-/* ------------------------------------------------------------------------- */
-
-#if defined(CONFIG_WATCHDOG)
-void watchdog_reset (void)
-{
- int re_enable = disable_interrupts ();
-
- reset_8xx_watchdog ((immap_t *) CONFIG_SYS_IMMR);
- if (re_enable)
- enable_interrupts ();
-}
-#endif /* CONFIG_WATCHDOG */
-
-#if defined(CONFIG_WATCHDOG)
-
-void reset_8xx_watchdog (volatile immap_t * immr)
-{
- /*
- * All other boards use the MPC8xx Internal Watchdog
- */
- immr->im_siu_conf.sc_swsr = 0x556c; /* write magic1 */
- immr->im_siu_conf.sc_swsr = 0xaa39; /* write magic2 */
-}
-#endif /* CONFIG_WATCHDOG */
-
-/*
- * Initializes on-chip ethernet controllers.
- * to override, implement board_eth_init()
- */
-int cpu_eth_init(bd_t *bis)
-{
-#if defined(SCC_ENET) && defined(CONFIG_CMD_NET)
- scc_initialize(bis);
-#endif
-#if defined(FEC_ENET)
- fec_initialize(bis);
-#endif
- return 0;
-}
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
deleted file mode 100644
index f621d6285ceb730b0380c1ee8e2988aa0a1214fe..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ /dev/null
@@ -1,218 +0,0 @@
-/*
- * (C) Copyright 2000-2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <watchdog.h>
-
-#include <mpc8xx.h>
-#include <commproc.h>
-
-#if defined(CONFIG_SYS_RTCSC) || defined(CONFIG_SYS_RMDS)
-DECLARE_GLOBAL_DATA_PTR;
-#endif
-
-#if defined(CONFIG_SYS_I2C_UCODE_PATCH) || defined(CONFIG_SYS_SPI_UCODE_PATCH) || \
- defined(CONFIG_SYS_SMC_UCODE_PATCH)
-void cpm_load_patch (volatile immap_t * immr);
-#endif
-
-/*
- * Breath some life into the CPU...
- *
- * Set up the memory map,
- * initialize a bunch of registers,
- * initialize the UPM's
- */
-void cpu_init_f (volatile immap_t * immr)
-{
- volatile memctl8xx_t *memctl = &immr->im_memctl;
-# ifdef CONFIG_SYS_PLPRCR
- ulong mfmask;
-# endif
- ulong reg;
-
- /* SYPCR - contains watchdog control (11-9) */
-
- immr->im_siu_conf.sc_sypcr = CONFIG_SYS_SYPCR;
-
-#if defined(CONFIG_WATCHDOG)
- reset_8xx_watchdog (immr);
-#endif /* CONFIG_WATCHDOG */
-
- /* SIUMCR - contains debug pin configuration (11-6) */
- immr->im_siu_conf.sc_siumcr |= CONFIG_SYS_SIUMCR;
- /* initialize timebase status and control register (11-26) */
- /* unlock TBSCRK */
-
- immr->im_sitk.sitk_tbscrk = KAPWR_KEY;
- immr->im_sit.sit_tbscr = CONFIG_SYS_TBSCR;
-
- /* initialize the PIT (11-31) */
-
- immr->im_sitk.sitk_piscrk = KAPWR_KEY;
- immr->im_sit.sit_piscr = CONFIG_SYS_PISCR;
-
- /* System integration timers. Don't change EBDF! (15-27) */
-
- immr->im_clkrstk.cark_sccrk = KAPWR_KEY;
- reg = immr->im_clkrst.car_sccr;
- reg &= SCCR_MASK;
- reg |= CONFIG_SYS_SCCR;
- immr->im_clkrst.car_sccr = reg;
-
- /* PLL (CPU clock) settings (15-30) */
-
- immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
-
- /* If CONFIG_SYS_PLPRCR (set in the various *_config.h files) tries to
- * set the MF field, then just copy CONFIG_SYS_PLPRCR over car_plprcr,
- * otherwise OR in CONFIG_SYS_PLPRCR so we do not change the current MF
- * field value.
- *
- * For newer (starting MPC866) chips PLPRCR layout is different.
- */
-#ifdef CONFIG_SYS_PLPRCR
- if (get_immr(0xFFFF) >= MPC8xx_NEW_CLK)
- mfmask = PLPRCR_MFACT_MSK;
- else
- mfmask = PLPRCR_MF_MSK;
-
- if ((CONFIG_SYS_PLPRCR & mfmask) != 0)
- reg = CONFIG_SYS_PLPRCR; /* reset control bits */
- else {
- reg = immr->im_clkrst.car_plprcr;
- reg &= mfmask; /* isolate MF-related fields */
- reg |= CONFIG_SYS_PLPRCR; /* reset control bits */
- }
- immr->im_clkrst.car_plprcr = reg;
-#endif
-
- /*
- * Memory Controller:
- */
-
- /* perform BR0 reset that MPC850 Rev. A can't guarantee */
- reg = memctl->memc_br0;
- reg &= BR_PS_MSK; /* Clear everything except Port Size bits */
- reg |= BR_V; /* then add just the "Bank Valid" bit */
- memctl->memc_br0 = reg;
-
- /* Map banks 0 (and maybe 1) to the FLASH banks 0 (and 1) at
- * preliminary addresses - these have to be modified later
- * when FLASH size has been determined
- *
- * Depending on the size of the memory region defined by
- * CONFIG_SYS_OR0_REMAP some boards (wide address mask) allow to map the
- * CONFIG_SYS_MONITOR_BASE, while others (narrower address mask) can't
- * map CONFIG_SYS_MONITOR_BASE.
- *
- * For example, for CONFIG_IVMS8, the CONFIG_SYS_MONITOR_BASE is
- * 0xff000000, but CONFIG_SYS_OR0_REMAP's address mask is 0xfff80000.
- *
- * If BR0 wasn't loaded with address base 0xff000000, then BR0's
- * base address remains as 0x00000000. However, the address mask
- * have been narrowed to 512Kb, so CONFIG_SYS_MONITOR_BASE wasn't mapped
- * into the Bank0.
- *
- * This is why CONFIG_IVMS8 and similar boards must load BR0 with
- * CONFIG_SYS_BR0_PRELIM in advance.
- *
- * [Thanks to Michael Liao for this explanation.
- * I owe him a free beer. - wd]
- */
-
-#if defined(CONFIG_SYS_OR0_REMAP)
- memctl->memc_or0 = CONFIG_SYS_OR0_REMAP;
-#endif
-#if defined(CONFIG_SYS_OR1_REMAP)
- memctl->memc_or1 = CONFIG_SYS_OR1_REMAP;
-#endif
-#if defined(CONFIG_SYS_OR5_REMAP)
- memctl->memc_or5 = CONFIG_SYS_OR5_REMAP;
-#endif
-
- /* now restrict to preliminary range */
- memctl->memc_br0 = CONFIG_SYS_BR0_PRELIM;
- memctl->memc_or0 = CONFIG_SYS_OR0_PRELIM;
-
-#if (defined(CONFIG_SYS_OR1_PRELIM) && defined(CONFIG_SYS_BR1_PRELIM))
- memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
- memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
- memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM;
- memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_OR3_PRELIM) && defined(CONFIG_SYS_BR3_PRELIM)
- memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_OR4_PRELIM) && defined(CONFIG_SYS_BR4_PRELIM)
- memctl->memc_or4 = CONFIG_SYS_OR4_PRELIM;
- memctl->memc_br4 = CONFIG_SYS_BR4_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_OR5_PRELIM) && defined(CONFIG_SYS_BR5_PRELIM)
- memctl->memc_or5 = CONFIG_SYS_OR5_PRELIM;
- memctl->memc_br5 = CONFIG_SYS_BR5_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_OR6_PRELIM) && defined(CONFIG_SYS_BR6_PRELIM)
- memctl->memc_or6 = CONFIG_SYS_OR6_PRELIM;
- memctl->memc_br6 = CONFIG_SYS_BR6_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_OR7_PRELIM) && defined(CONFIG_SYS_BR7_PRELIM)
- memctl->memc_or7 = CONFIG_SYS_OR7_PRELIM;
- memctl->memc_br7 = CONFIG_SYS_BR7_PRELIM;
-#endif
-
- /*
- * Reset CPM
- */
- immr->im_cpm.cp_cpcr = CPM_CR_RST | CPM_CR_FLG;
- do { /* Spin until command processed */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
-
-#ifdef CONFIG_SYS_RCCR /* must be done before cpm_load_patch() */
- /* write config value */
- immr->im_cpm.cp_rccr = CONFIG_SYS_RCCR;
-#endif
-
-#if defined(CONFIG_SYS_I2C_UCODE_PATCH) || defined(CONFIG_SYS_SPI_UCODE_PATCH) || \
- defined(CONFIG_SYS_SMC_UCODE_PATCH)
- cpm_load_patch (immr); /* load mpc8xx microcode patch */
-#endif
-}
-
-/*
- * initialize higher level parts of CPU like timers
- */
-int cpu_init_r (void)
-{
-#if defined(CONFIG_SYS_RTCSC) || defined(CONFIG_SYS_RMDS)
- bd_t *bd = gd->bd;
- volatile immap_t *immr = (volatile immap_t *) (bd->bi_immr_base);
-#endif
-
-#ifdef CONFIG_SYS_RTCSC
- /* Unlock RTSC register */
- immr->im_sitk.sitk_rtcsck = KAPWR_KEY;
- /* write config value */
- immr->im_sit.sit_rtcsc = CONFIG_SYS_RTCSC;
-#endif
-
-#ifdef CONFIG_SYS_RMDS
- /* write config value */
- immr->im_cpm.cp_rmds = CONFIG_SYS_RMDS;
-#endif
- return (0);
-}
diff --git a/arch/powerpc/cpu/mpc8xx/fdt.c b/arch/powerpc/cpu/mpc8xx/fdt.c
deleted file mode 100644
index 34d36478d30ac2f2c36b105b357cb8020056d2e3..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/fdt.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * Copyright 2008 (C) Bryan O'Donoghue
- *
- * Code copied & edited from Freescale mpc85xx stuff.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void ft_cpu_setup(void *blob, bd_t *bd)
-{
- do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
- "timebase-frequency", get_tbclk(), 1);
- do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
- "bus-frequency", bd->bi_busfreq, 1);
- do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
- "clock-frequency", bd->bi_intfreq, 1);
- do_fixup_by_compat_u32(blob, "fsl,cpm-brg", "clock-frequency",
- gd->arch.brg_clk, 1);
-
- fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize);
-}
diff --git a/arch/powerpc/cpu/mpc8xx/fec.c b/arch/powerpc/cpu/mpc8xx/fec.c
deleted file mode 100644
index b27310fffb97bb46b03652a7dafe5a08472b8b80..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/fec.c
+++ /dev/null
@@ -1,933 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <commproc.h>
-#include <malloc.h>
-#include <net.h>
-
-#include <phy.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#undef ET_DEBUG
-
-#if defined(CONFIG_CMD_NET) && \
- (defined(FEC_ENET) || defined(CONFIG_ETHER_ON_FEC1) || defined(CONFIG_ETHER_ON_FEC2))
-
-/* compatibility test, if only FEC_ENET defined assume ETHER on FEC1 */
-#if defined(FEC_ENET) && !defined(CONFIG_ETHER_ON_FEC1) && !defined(CONFIG_ETHER_ON_FEC2)
-#define CONFIG_ETHER_ON_FEC1 1
-#endif
-
-/* define WANT_MII when MII support is required */
-#if defined(CONFIG_SYS_DISCOVER_PHY) || defined(CONFIG_FEC1_PHY) || defined(CONFIG_FEC2_PHY)
-#define WANT_MII
-#else
-#undef WANT_MII
-#endif
-
-#if defined(WANT_MII)
-#include <miiphy.h>
-
-#if !(defined(CONFIG_MII) || defined(CONFIG_CMD_MII))
-#error "CONFIG_MII has to be defined!"
-#endif
-
-#endif
-
-#if defined(CONFIG_RMII) && !defined(WANT_MII)
-#error RMII support is unusable without a working PHY.
-#endif
-
-#ifdef CONFIG_SYS_DISCOVER_PHY
-static int mii_discover_phy(struct eth_device *dev);
-#endif
-
-int fec8xx_miiphy_read(struct mii_dev *bus, int addr, int devad, int reg);
-int fec8xx_miiphy_write(struct mii_dev *bus, int addr, int devad, int reg,
- u16 value);
-
-static struct ether_fcc_info_s
-{
- int ether_index;
- int fecp_offset;
- int phy_addr;
- int actual_phy_addr;
- int initialized;
-}
- ether_fcc_info[] = {
-#if defined(CONFIG_ETHER_ON_FEC1)
- {
- 0,
- offsetof(immap_t, im_cpm.cp_fec1),
-#if defined(CONFIG_FEC1_PHY)
- CONFIG_FEC1_PHY,
-#else
- -1, /* discover */
-#endif
- -1,
- 0,
-
- },
-#endif
-#if defined(CONFIG_ETHER_ON_FEC2)
- {
- 1,
- offsetof(immap_t, im_cpm.cp_fec2),
-#if defined(CONFIG_FEC2_PHY)
- CONFIG_FEC2_PHY,
-#else
- -1,
-#endif
- -1,
- 0,
- },
-#endif
-};
-
-/* Ethernet Transmit and Receive Buffers */
-#define DBUF_LENGTH 1520
-
-#define TX_BUF_CNT 2
-
-#define TOUT_LOOP 100
-
-#define PKT_MAXBUF_SIZE 1518
-#define PKT_MINBUF_SIZE 64
-#define PKT_MAXBLR_SIZE 1520
-
-#ifdef __GNUC__
-static char txbuf[DBUF_LENGTH] __attribute__ ((aligned(8)));
-#else
-#error txbuf must be aligned.
-#endif
-
-static uint rxIdx; /* index of the current RX buffer */
-static uint txIdx; /* index of the current TX buffer */
-
-/*
- * FEC Ethernet Tx and Rx buffer descriptors allocated at the
- * immr->udata_bd address on Dual-Port RAM
- * Provide for Double Buffering
- */
-
-typedef volatile struct CommonBufferDescriptor {
- cbd_t rxbd[PKTBUFSRX]; /* Rx BD */
- cbd_t txbd[TX_BUF_CNT]; /* Tx BD */
-} RTXBD;
-
-static RTXBD *rtx = NULL;
-
-static int fec_send(struct eth_device *dev, void *packet, int length);
-static int fec_recv(struct eth_device* dev);
-static int fec_init(struct eth_device* dev, bd_t * bd);
-static void fec_halt(struct eth_device* dev);
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
-static void __mii_init(void);
-#endif
-
-int fec_initialize(bd_t *bis)
-{
- struct eth_device* dev;
- struct ether_fcc_info_s *efis;
- int i;
-
- for (i = 0; i < ARRAY_SIZE(ether_fcc_info); i++) {
-
- dev = malloc(sizeof(*dev));
- if (dev == NULL)
- hang();
-
- memset(dev, 0, sizeof(*dev));
-
- /* for FEC1 make sure that the name of the interface is the same
- as the old one for compatibility reasons */
- if (i == 0) {
- strcpy(dev->name, "FEC");
- } else {
- sprintf (dev->name, "FEC%d",
- ether_fcc_info[i].ether_index + 1);
- }
-
- efis = ðer_fcc_info[i];
-
- /*
- * reset actual phy addr
- */
- efis->actual_phy_addr = -1;
-
- dev->priv = efis;
- dev->init = fec_init;
- dev->halt = fec_halt;
- dev->send = fec_send;
- dev->recv = fec_recv;
-
- eth_register(dev);
-
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
- int retval;
- struct mii_dev *mdiodev = mdio_alloc();
- if (!mdiodev)
- return -ENOMEM;
- strncpy(mdiodev->name, dev->name, MDIO_NAME_LEN);
- mdiodev->read = fec8xx_miiphy_read;
- mdiodev->write = fec8xx_miiphy_write;
-
- retval = mdio_register(mdiodev);
- if (retval < 0)
- return retval;
-#endif
- }
- return 1;
-}
-
-static int fec_send(struct eth_device *dev, void *packet, int length)
-{
- int j, rc;
- struct ether_fcc_info_s *efis = dev->priv;
- volatile fec_t *fecp = (volatile fec_t *)(CONFIG_SYS_IMMR + efis->fecp_offset);
-
- /* section 16.9.23.3
- * Wait for ready
- */
- j = 0;
- while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
- udelay(1);
- j++;
- }
- if (j>=TOUT_LOOP) {
- printf("TX not ready\n");
- }
-
- rtx->txbd[txIdx].cbd_bufaddr = (uint)packet;
- rtx->txbd[txIdx].cbd_datlen = length;
- rtx->txbd[txIdx].cbd_sc |= BD_ENET_TX_READY | BD_ENET_TX_LAST;
- __asm__ ("eieio");
-
- /* Activate transmit Buffer Descriptor polling */
- fecp->fec_x_des_active = 0x01000000; /* Descriptor polling active */
-
- j = 0;
- while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
- udelay(1);
- j++;
- }
- if (j>=TOUT_LOOP) {
- printf("TX timeout\n");
- }
-#ifdef ET_DEBUG
- printf("%s[%d] %s: cycles: %d status: %x retry cnt: %d\n",
- __FILE__,__LINE__,__FUNCTION__,j,rtx->txbd[txIdx].cbd_sc,
- (rtx->txbd[txIdx].cbd_sc & 0x003C)>>2);
-#endif
- /* return only status bits */;
- rc = (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_STATS);
-
- txIdx = (txIdx + 1) % TX_BUF_CNT;
-
- return rc;
-}
-
-static int fec_recv (struct eth_device *dev)
-{
- struct ether_fcc_info_s *efis = dev->priv;
- volatile fec_t *fecp =
- (volatile fec_t *) (CONFIG_SYS_IMMR + efis->fecp_offset);
- int length;
-
- for (;;) {
- /* section 16.9.23.2 */
- if (rtx->rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
- length = -1;
- break; /* nothing received - leave for() loop */
- }
-
- length = rtx->rxbd[rxIdx].cbd_datlen;
-
- if (rtx->rxbd[rxIdx].cbd_sc & 0x003f) {
-#ifdef ET_DEBUG
- printf ("%s[%d] err: %x\n",
- __FUNCTION__, __LINE__,
- rtx->rxbd[rxIdx].cbd_sc);
-#endif
- } else {
- uchar *rx = net_rx_packets[rxIdx];
-
- length -= 4;
-
-#if defined(CONFIG_CMD_CDP)
- if ((rx[0] & 1) != 0 &&
- memcmp((uchar *)rx, net_bcast_ethaddr, 6) != 0 &&
- !is_cdp_packet((uchar *)rx))
- rx = NULL;
-#endif
- /*
- * Pass the packet up to the protocol layers.
- */
- if (rx != NULL)
- net_process_received_packet(rx, length);
- }
-
- /* Give the buffer back to the FEC. */
- rtx->rxbd[rxIdx].cbd_datlen = 0;
-
- /* wrap around buffer index when necessary */
- if ((rxIdx + 1) >= PKTBUFSRX) {
- rtx->rxbd[PKTBUFSRX - 1].cbd_sc =
- (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
- rxIdx = 0;
- } else {
- rtx->rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
- rxIdx++;
- }
-
- __asm__ ("eieio");
-
- /* Try to fill Buffer Descriptors */
- fecp->fec_r_des_active = 0x01000000; /* Descriptor polling active */
- }
-
- return length;
-}
-
-/**************************************************************
- *
- * FEC Ethernet Initialization Routine
- *
- *************************************************************/
-
-#define FEC_ECNTRL_PINMUX 0x00000004
-#define FEC_ECNTRL_ETHER_EN 0x00000002
-#define FEC_ECNTRL_RESET 0x00000001
-
-#define FEC_RCNTRL_BC_REJ 0x00000010
-#define FEC_RCNTRL_PROM 0x00000008
-#define FEC_RCNTRL_MII_MODE 0x00000004
-#define FEC_RCNTRL_DRT 0x00000002
-#define FEC_RCNTRL_LOOP 0x00000001
-
-#define FEC_TCNTRL_FDEN 0x00000004
-#define FEC_TCNTRL_HBC 0x00000002
-#define FEC_TCNTRL_GTS 0x00000001
-
-#define FEC_RESET_DELAY 50
-
-#if defined(CONFIG_RMII)
-
-static inline void fec_10Mbps(struct eth_device *dev)
-{
- struct ether_fcc_info_s *efis = dev->priv;
- int fecidx = efis->ether_index;
- uint mask = (fecidx == 0) ? 0x0000010 : 0x0000008;
-
- if ((unsigned int)fecidx >= 2)
- hang();
-
- ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_cptr |= mask;
-}
-
-static inline void fec_100Mbps(struct eth_device *dev)
-{
- struct ether_fcc_info_s *efis = dev->priv;
- int fecidx = efis->ether_index;
- uint mask = (fecidx == 0) ? 0x0000010 : 0x0000008;
-
- if ((unsigned int)fecidx >= 2)
- hang();
-
- ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_cptr &= ~mask;
-}
-
-#endif
-
-static inline void fec_full_duplex(struct eth_device *dev)
-{
- struct ether_fcc_info_s *efis = dev->priv;
- volatile fec_t *fecp = (volatile fec_t *)(CONFIG_SYS_IMMR + efis->fecp_offset);
-
- fecp->fec_r_cntrl &= ~FEC_RCNTRL_DRT;
- fecp->fec_x_cntrl |= FEC_TCNTRL_FDEN; /* FD enable */
-}
-
-static inline void fec_half_duplex(struct eth_device *dev)
-{
- struct ether_fcc_info_s *efis = dev->priv;
- volatile fec_t *fecp = (volatile fec_t *)(CONFIG_SYS_IMMR + efis->fecp_offset);
-
- fecp->fec_r_cntrl |= FEC_RCNTRL_DRT;
- fecp->fec_x_cntrl &= ~FEC_TCNTRL_FDEN; /* FD disable */
-}
-
-static void fec_pin_init(int fecidx)
-{
- bd_t *bd = gd->bd;
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- /*
- * Set MII speed to 2.5 MHz or slightly below.
- *
- * According to the MPC860T (Rev. D) Fast ethernet controller user
- * manual (6.2.14),
- * the MII management interface clock must be less than or equal
- * to 2.5 MHz.
- * This MDC frequency is equal to system clock / (2 * MII_SPEED).
- * Then MII_SPEED = system_clock / 2 * 2,5 MHz.
- *
- * All MII configuration is done via FEC1 registers:
- */
- immr->im_cpm.cp_fec1.fec_mii_speed = ((bd->bi_intfreq + 4999999) / 5000000) << 1;
-
-#if defined(CONFIG_MPC885_FAMILY) && defined(WANT_MII)
- /* use MDC for MII */
- immr->im_ioport.iop_pdpar |= 0x0080;
- immr->im_ioport.iop_pddir &= ~0x0080;
-#endif
-
- if (fecidx == 0) {
-#if defined(CONFIG_ETHER_ON_FEC1)
-
-#if defined(CONFIG_MPC885_FAMILY) /* MPC87x/88x have got 2 FECs and different pinout */
-
-#if !defined(CONFIG_RMII)
-
- immr->im_ioport.iop_papar |= 0xf830;
- immr->im_ioport.iop_padir |= 0x0830;
- immr->im_ioport.iop_padir &= ~0xf000;
-
- immr->im_cpm.cp_pbpar |= 0x00001001;
- immr->im_cpm.cp_pbdir &= ~0x00001001;
-
- immr->im_ioport.iop_pcpar |= 0x000c;
- immr->im_ioport.iop_pcdir &= ~0x000c;
-
- immr->im_cpm.cp_pepar |= 0x00000003;
- immr->im_cpm.cp_pedir |= 0x00000003;
- immr->im_cpm.cp_peso &= ~0x00000003;
-
- immr->im_cpm.cp_cptr &= ~0x00000100;
-
-#else
-
-#if !defined(CONFIG_FEC1_PHY_NORXERR)
- immr->im_ioport.iop_papar |= 0x1000;
- immr->im_ioport.iop_padir &= ~0x1000;
-#endif
- immr->im_ioport.iop_papar |= 0xe810;
- immr->im_ioport.iop_padir |= 0x0810;
- immr->im_ioport.iop_padir &= ~0xe000;
-
- immr->im_cpm.cp_pbpar |= 0x00000001;
- immr->im_cpm.cp_pbdir &= ~0x00000001;
-
- immr->im_cpm.cp_cptr |= 0x00000100;
- immr->im_cpm.cp_cptr &= ~0x00000050;
-
-#endif /* !CONFIG_RMII */
-
-#else
- /*
- * Configure all of port D for MII.
- */
- immr->im_ioport.iop_pdpar = 0x1fff;
-
- /*
- * Bits moved from Rev. D onward
- */
- if ((get_immr(0) & 0xffff) < 0x0501)
- immr->im_ioport.iop_pddir = 0x1c58; /* Pre rev. D */
- else
- immr->im_ioport.iop_pddir = 0x1fff; /* Rev. D and later */
-#endif
-
-#endif /* CONFIG_ETHER_ON_FEC1 */
- } else if (fecidx == 1) {
-
-#if defined(CONFIG_ETHER_ON_FEC2)
-
-#if defined(CONFIG_MPC885_FAMILY) /* MPC87x/88x have got 2 FECs and different pinout */
-
-#if !defined(CONFIG_RMII)
- immr->im_cpm.cp_pepar |= 0x0003fffc;
- immr->im_cpm.cp_pedir |= 0x0003fffc;
- immr->im_cpm.cp_peso &= ~0x000087fc;
- immr->im_cpm.cp_peso |= 0x00037800;
-
- immr->im_cpm.cp_cptr &= ~0x00000080;
-#else
-
-#if !defined(CONFIG_FEC2_PHY_NORXERR)
- immr->im_cpm.cp_pepar |= 0x00000010;
- immr->im_cpm.cp_pedir |= 0x00000010;
- immr->im_cpm.cp_peso &= ~0x00000010;
-#endif
- immr->im_cpm.cp_pepar |= 0x00039620;
- immr->im_cpm.cp_pedir |= 0x00039620;
- immr->im_cpm.cp_peso |= 0x00031000;
- immr->im_cpm.cp_peso &= ~0x00008620;
-
- immr->im_cpm.cp_cptr |= 0x00000080;
- immr->im_cpm.cp_cptr &= ~0x00000028;
-#endif /* CONFIG_RMII */
-
-#endif /* CONFIG_MPC885_FAMILY */
-
-#endif /* CONFIG_ETHER_ON_FEC2 */
-
- }
-}
-
-static int fec_reset(volatile fec_t *fecp)
-{
- int i;
-
- /* Whack a reset.
- * A delay is required between a reset of the FEC block and
- * initialization of other FEC registers because the reset takes
- * some time to complete. If you don't delay, subsequent writes
- * to FEC registers might get killed by the reset routine which is
- * still in progress.
- */
-
- fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_RESET;
- for (i = 0;
- (fecp->fec_ecntrl & FEC_ECNTRL_RESET) && (i < FEC_RESET_DELAY);
- ++i) {
- udelay (1);
- }
- if (i == FEC_RESET_DELAY)
- return -1;
-
- return 0;
-}
-
-static int fec_init (struct eth_device *dev, bd_t * bd)
-{
- struct ether_fcc_info_s *efis = dev->priv;
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile fec_t *fecp =
- (volatile fec_t *) (CONFIG_SYS_IMMR + efis->fecp_offset);
- int i;
-
-#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
- /* the MII interface is connected to FEC1
- * so for the miiphy_xxx function to work we must
- * call mii_init since fec_halt messes the thing up
- */
- if (efis->ether_index != 0)
- __mii_init();
-#endif
-
- if (fec_reset(fecp) < 0)
- printf ("FEC_RESET_DELAY timeout\n");
-
- /* We use strictly polling mode only
- */
- fecp->fec_imask = 0;
-
- /* Clear any pending interrupt
- */
- fecp->fec_ievent = 0xffc0;
-
- /* No need to set the IVEC register */
-
- /* Set station address
- */
-#define ea dev->enetaddr
- fecp->fec_addr_low = (ea[0] << 24) | (ea[1] << 16) | (ea[2] << 8) | (ea[3]);
- fecp->fec_addr_high = (ea[4] << 8) | (ea[5]);
-#undef ea
-
-#if defined(CONFIG_CMD_CDP)
- /*
- * Turn on multicast address hash table
- */
- fecp->fec_hash_table_high = 0xffffffff;
- fecp->fec_hash_table_low = 0xffffffff;
-#else
- /* Clear multicast address hash table
- */
- fecp->fec_hash_table_high = 0;
- fecp->fec_hash_table_low = 0;
-#endif
-
- /* Set maximum receive buffer size.
- */
- fecp->fec_r_buff_size = PKT_MAXBLR_SIZE;
-
- /* Set maximum frame length
- */
- fecp->fec_r_hash = PKT_MAXBUF_SIZE;
-
- /*
- * Setup Buffers and Buffer Desriptors
- */
- rxIdx = 0;
- txIdx = 0;
-
- if (!rtx)
- rtx = (RTXBD *)(immr->im_cpm.cp_dpmem + CPM_FEC_BASE);
- /*
- * Setup Receiver Buffer Descriptors (13.14.24.18)
- * Settings:
- * Empty, Wrap
- */
- for (i = 0; i < PKTBUFSRX; i++) {
- rtx->rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
- rtx->rxbd[i].cbd_datlen = 0; /* Reset */
- rtx->rxbd[i].cbd_bufaddr = (uint) net_rx_packets[i];
- }
- rtx->rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;
-
- /*
- * Setup Ethernet Transmitter Buffer Descriptors (13.14.24.19)
- * Settings:
- * Last, Tx CRC
- */
- for (i = 0; i < TX_BUF_CNT; i++) {
- rtx->txbd[i].cbd_sc = BD_ENET_TX_LAST | BD_ENET_TX_TC;
- rtx->txbd[i].cbd_datlen = 0; /* Reset */
- rtx->txbd[i].cbd_bufaddr = (uint) (&txbuf[0]);
- }
- rtx->txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
-
- /* Set receive and transmit descriptor base
- */
- fecp->fec_r_des_start = (unsigned int) (&rtx->rxbd[0]);
- fecp->fec_x_des_start = (unsigned int) (&rtx->txbd[0]);
-
- /* Enable MII mode
- */
-#if 0 /* Full duplex mode */
- fecp->fec_r_cntrl = FEC_RCNTRL_MII_MODE;
- fecp->fec_x_cntrl = FEC_TCNTRL_FDEN;
-#else /* Half duplex mode */
- fecp->fec_r_cntrl = FEC_RCNTRL_MII_MODE | FEC_RCNTRL_DRT;
- fecp->fec_x_cntrl = 0;
-#endif
-
- /* Enable big endian and don't care about SDMA FC.
- */
- fecp->fec_fun_code = 0x78000000;
-
- /*
- * Setup the pin configuration of the FEC
- */
- fec_pin_init (efis->ether_index);
-
- rxIdx = 0;
- txIdx = 0;
-
- /*
- * Now enable the transmit and receive processing
- */
- fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN;
-
- if (efis->phy_addr == -1) {
-#ifdef CONFIG_SYS_DISCOVER_PHY
- /*
- * wait for the PHY to wake up after reset
- */
- efis->actual_phy_addr = mii_discover_phy (dev);
-
- if (efis->actual_phy_addr == -1) {
- printf ("Unable to discover phy!\n");
- return -1;
- }
-#else
- efis->actual_phy_addr = -1;
-#endif
- } else {
- efis->actual_phy_addr = efis->phy_addr;
- }
-
-#if defined(CONFIG_MII) && defined(CONFIG_RMII)
- /*
- * adapt the RMII speed to the speed of the phy
- */
- if (miiphy_speed (dev->name, efis->actual_phy_addr) == _100BASET) {
- fec_100Mbps (dev);
- } else {
- fec_10Mbps (dev);
- }
-#endif
-
-#if defined(CONFIG_MII)
- /*
- * adapt to the half/full speed settings
- */
- if (miiphy_duplex (dev->name, efis->actual_phy_addr) == FULL) {
- fec_full_duplex (dev);
- } else {
- fec_half_duplex (dev);
- }
-#endif
-
- /* And last, try to fill Rx Buffer Descriptors */
- fecp->fec_r_des_active = 0x01000000; /* Descriptor polling active */
-
- efis->initialized = 1;
-
- return 0;
-}
-
-
-static void fec_halt(struct eth_device* dev)
-{
- struct ether_fcc_info_s *efis = dev->priv;
- volatile fec_t *fecp = (volatile fec_t *)(CONFIG_SYS_IMMR + efis->fecp_offset);
- int i;
-
- /* avoid halt if initialized; mii gets stuck otherwise */
- if (!efis->initialized)
- return;
-
- /* Whack a reset.
- * A delay is required between a reset of the FEC block and
- * initialization of other FEC registers because the reset takes
- * some time to complete. If you don't delay, subsequent writes
- * to FEC registers might get killed by the reset routine which is
- * still in progress.
- */
-
- fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_RESET;
- for (i = 0;
- (fecp->fec_ecntrl & FEC_ECNTRL_RESET) && (i < FEC_RESET_DELAY);
- ++i) {
- udelay (1);
- }
- if (i == FEC_RESET_DELAY) {
- printf ("FEC_RESET_DELAY timeout\n");
- return;
- }
-
- efis->initialized = 0;
-}
-
-#if defined(CONFIG_SYS_DISCOVER_PHY) || defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
-
-/* Make MII read/write commands for the FEC.
-*/
-
-#define mk_mii_read(ADDR, REG) (0x60020000 | ((ADDR << 23) | \
- (REG & 0x1f) << 18))
-
-#define mk_mii_write(ADDR, REG, VAL) (0x50020000 | ((ADDR << 23) | \
- (REG & 0x1f) << 18) | \
- (VAL & 0xffff))
-
-/* Interrupt events/masks.
-*/
-#define FEC_ENET_HBERR ((uint)0x80000000) /* Heartbeat error */
-#define FEC_ENET_BABR ((uint)0x40000000) /* Babbling receiver */
-#define FEC_ENET_BABT ((uint)0x20000000) /* Babbling transmitter */
-#define FEC_ENET_GRA ((uint)0x10000000) /* Graceful stop complete */
-#define FEC_ENET_TXF ((uint)0x08000000) /* Full frame transmitted */
-#define FEC_ENET_TXB ((uint)0x04000000) /* A buffer was transmitted */
-#define FEC_ENET_RXF ((uint)0x02000000) /* Full frame received */
-#define FEC_ENET_RXB ((uint)0x01000000) /* A buffer was received */
-#define FEC_ENET_MII ((uint)0x00800000) /* MII interrupt */
-#define FEC_ENET_EBERR ((uint)0x00400000) /* SDMA bus error */
-
-/* PHY identification
- */
-#define PHY_ID_LXT970 0x78100000 /* LXT970 */
-#define PHY_ID_LXT971 0x001378e0 /* LXT971 and 972 */
-#define PHY_ID_82555 0x02a80150 /* Intel 82555 */
-#define PHY_ID_QS6612 0x01814400 /* QS6612 */
-#define PHY_ID_AMD79C784 0x00225610 /* AMD 79C784 */
-#define PHY_ID_LSI80225 0x0016f870 /* LSI 80225 */
-#define PHY_ID_LSI80225B 0x0016f880 /* LSI 80225/B */
-#define PHY_ID_DM9161 0x0181B880 /* Davicom DM9161 */
-#define PHY_ID_KSM8995M 0x00221450 /* MICREL KS8995MA */
-
-/* send command to phy using mii, wait for result */
-static uint
-mii_send(uint mii_cmd)
-{
- uint mii_reply;
- volatile fec_t *ep;
- int cnt;
-
- ep = &(((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_fec);
-
- ep->fec_mii_data = mii_cmd; /* command to phy */
-
- /* wait for mii complete */
- cnt = 0;
- while (!(ep->fec_ievent & FEC_ENET_MII)) {
- if (++cnt > 1000) {
- printf("mii_send STUCK!\n");
- break;
- }
- }
- mii_reply = ep->fec_mii_data; /* result from phy */
- ep->fec_ievent = FEC_ENET_MII; /* clear MII complete */
-#if 0
- printf("%s[%d] %s: sent=0x%8.8x, reply=0x%8.8x\n",
- __FILE__,__LINE__,__FUNCTION__,mii_cmd,mii_reply);
-#endif
- return (mii_reply & 0xffff); /* data read from phy */
-}
-#endif
-
-#if defined(CONFIG_SYS_DISCOVER_PHY)
-static int mii_discover_phy(struct eth_device *dev)
-{
-#define MAX_PHY_PASSES 11
- uint phyno;
- int pass;
- uint phytype;
- int phyaddr;
-
- phyaddr = -1; /* didn't find a PHY yet */
- for (pass = 1; pass <= MAX_PHY_PASSES && phyaddr < 0; ++pass) {
- if (pass > 1) {
- /* PHY may need more time to recover from reset.
- * The LXT970 needs 50ms typical, no maximum is
- * specified, so wait 10ms before try again.
- * With 11 passes this gives it 100ms to wake up.
- */
- udelay(10000); /* wait 10ms */
- }
- for (phyno = 0; phyno < 32 && phyaddr < 0; ++phyno) {
- phytype = mii_send(mk_mii_read(phyno, MII_PHYSID2));
-#ifdef ET_DEBUG
- printf("PHY type 0x%x pass %d type ", phytype, pass);
-#endif
- if (phytype != 0xffff) {
- phyaddr = phyno;
- phytype |= mii_send(mk_mii_read(phyno,
- MII_PHYSID1)) << 16;
-
-#ifdef ET_DEBUG
- printf("PHY @ 0x%x pass %d type ",phyno,pass);
- switch (phytype & 0xfffffff0) {
- case PHY_ID_LXT970:
- printf("LXT970\n");
- break;
- case PHY_ID_LXT971:
- printf("LXT971\n");
- break;
- case PHY_ID_82555:
- printf("82555\n");
- break;
- case PHY_ID_QS6612:
- printf("QS6612\n");
- break;
- case PHY_ID_AMD79C784:
- printf("AMD79C784\n");
- break;
- case PHY_ID_LSI80225B:
- printf("LSI L80225/B\n");
- break;
- case PHY_ID_DM9161:
- printf("Davicom DM9161\n");
- break;
- case PHY_ID_KSM8995M:
- printf("MICREL KS8995M\n");
- break;
- default:
- printf("0x%08x\n", phytype);
- break;
- }
-#endif
- }
- }
- }
- if (phyaddr < 0) {
- printf("No PHY device found.\n");
- }
- return phyaddr;
-}
-#endif /* CONFIG_SYS_DISCOVER_PHY */
-
-#if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII)) && !defined(CONFIG_BITBANGMII)
-
-/****************************************************************************
- * mii_init -- Initialize the MII via FEC 1 for MII command without ethernet
- * This function is a subset of eth_init
- ****************************************************************************
- */
-static void __mii_init(void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile fec_t *fecp = &(immr->im_cpm.cp_fec);
-
- if (fec_reset(fecp) < 0)
- printf ("FEC_RESET_DELAY timeout\n");
-
- /* We use strictly polling mode only
- */
- fecp->fec_imask = 0;
-
- /* Clear any pending interrupt
- */
- fecp->fec_ievent = 0xffc0;
-
- /* Now enable the transmit and receive processing
- */
- fecp->fec_ecntrl = FEC_ECNTRL_PINMUX | FEC_ECNTRL_ETHER_EN;
-}
-
-void mii_init (void)
-{
- int i;
-
- __mii_init();
-
- /* Setup the pin configuration of the FEC(s)
- */
- for (i = 0; i < ARRAY_SIZE(ether_fcc_info); i++)
- fec_pin_init(ether_fcc_info[i].ether_index);
-}
-
-/*****************************************************************************
- * Read and write a MII PHY register, routines used by MII Utilities
- *
- * FIXME: These routines are expected to return 0 on success, but mii_send
- * does _not_ return an error code. Maybe 0xFFFF means error, i.e.
- * no PHY connected...
- * For now always return 0.
- * FIXME: These routines only work after calling eth_init() at least once!
- * Otherwise they hang in mii_send() !!! Sorry!
- *****************************************************************************/
-
-int fec8xx_miiphy_read(struct mii_dev *bus, int addr, int devad, int reg)
-{
- unsigned short value = 0;
- short rdreg; /* register working value */
-
-#ifdef MII_DEBUG
- printf ("miiphy_read(0x%x) @ 0x%x = ", reg, addr);
-#endif
- rdreg = mii_send(mk_mii_read(addr, reg));
-
- value = rdreg;
-#ifdef MII_DEBUG
- printf ("0x%04x\n", value);
-#endif
- return value;
-}
-
-int fec8xx_miiphy_write(struct mii_dev *bus, int addr, int devad, int reg,
- u16 value)
-{
-#ifdef MII_DEBUG
- printf ("miiphy_write(0x%x) @ 0x%x = ", reg, addr);
-#endif
- (void)mii_send(mk_mii_write(addr, reg, value));
-
-#ifdef MII_DEBUG
- printf ("0x%04x\n", value);
-#endif
- return 0;
-}
-#endif
-
-#endif
diff --git a/arch/powerpc/cpu/mpc8xx/fec.h b/arch/powerpc/cpu/mpc8xx/fec.h
deleted file mode 100644
index e025c3f464430bd4b9435936d08317c37ee85bbf..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/fec.h
+++ /dev/null
@@ -1,12 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _FEC_H_
-#define _FEC_H_
-
-
-#endif /* _FEC_H_ */
diff --git a/arch/powerpc/cpu/mpc8xx/interrupts.c b/arch/powerpc/cpu/mpc8xx/interrupts.c
deleted file mode 100644
index 482ceecb9fb7398a46d0856c71ca6a21a278d839..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/interrupts.c
+++ /dev/null
@@ -1,278 +0,0 @@
-/*
- * (C) Copyright 2000-2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <mpc8xx_irq.h>
-#include <asm/processor.h>
-#include <commproc.h>
-
-/************************************************************************/
-
-/*
- * CPM interrupt vector functions.
- */
-struct interrupt_action {
- interrupt_handler_t *handler;
- void *arg;
-};
-
-static struct interrupt_action cpm_vecs[CPMVEC_NR];
-static struct interrupt_action irq_vecs[NR_IRQS];
-
-static void cpm_interrupt_init (void);
-static void cpm_interrupt (void *regs);
-
-/************************************************************************/
-
-int interrupt_init_cpu (unsigned *decrementer_count)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- *decrementer_count = get_tbclk () / CONFIG_SYS_HZ;
-
- /* disable all interrupts */
- immr->im_siu_conf.sc_simask = 0;
-
- /* Configure CPM interrupts */
- cpm_interrupt_init ();
-
- return (0);
-}
-
-/************************************************************************/
-
-/*
- * Handle external interrupts
- */
-void external_interrupt (struct pt_regs *regs)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- int irq;
- ulong simask, newmask;
- ulong vec, v_bit;
-
- /*
- * read the SIVEC register and shift the bits down
- * to get the irq number
- */
- vec = immr->im_siu_conf.sc_sivec;
- irq = vec >> 26;
- v_bit = 0x80000000UL >> irq;
-
- /*
- * Read Interrupt Mask Register and Mask Interrupts
- */
- simask = immr->im_siu_conf.sc_simask;
- newmask = simask & (~(0xFFFF0000 >> irq));
- immr->im_siu_conf.sc_simask = newmask;
-
- if (!(irq & 0x1)) { /* External Interrupt ? */
- ulong siel;
-
- /*
- * Read Interrupt Edge/Level Register
- */
- siel = immr->im_siu_conf.sc_siel;
-
- if (siel & v_bit) { /* edge triggered interrupt ? */
- /*
- * Rewrite SIPEND Register to clear interrupt
- */
- immr->im_siu_conf.sc_sipend = v_bit;
- }
- }
-
- if (irq_vecs[irq].handler != NULL) {
- irq_vecs[irq].handler (irq_vecs[irq].arg);
- } else {
- printf ("\nBogus External Interrupt IRQ %d Vector %ld\n",
- irq, vec);
- /* turn off the bogus interrupt to avoid it from now */
- simask &= ~v_bit;
- }
- /*
- * Re-Enable old Interrupt Mask
- */
- immr->im_siu_conf.sc_simask = simask;
-}
-
-/************************************************************************/
-
-/*
- * CPM interrupt handler
- */
-static void cpm_interrupt (void *regs)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- uint vec;
-
- /*
- * Get the vector by setting the ACK bit
- * and then reading the register.
- */
- immr->im_cpic.cpic_civr = 1;
- vec = immr->im_cpic.cpic_civr;
- vec >>= 11;
-
- if (cpm_vecs[vec].handler != NULL) {
- (*cpm_vecs[vec].handler) (cpm_vecs[vec].arg);
- } else {
- immr->im_cpic.cpic_cimr &= ~(1 << vec);
- printf ("Masking bogus CPM interrupt vector 0x%x\n", vec);
- }
- /*
- * After servicing the interrupt,
- * we have to remove the status indicator.
- */
- immr->im_cpic.cpic_cisr |= (1 << vec);
-}
-
-/*
- * The CPM can generate the error interrupt when there is a race
- * condition between generating and masking interrupts. All we have
- * to do is ACK it and return. This is a no-op function so we don't
- * need any special tests in the interrupt handler.
- */
-static void cpm_error_interrupt (void *dummy)
-{
-}
-
-/************************************************************************/
-/*
- * Install and free an interrupt handler
- */
-void irq_install_handler (int vec, interrupt_handler_t * handler,
- void *arg)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- if ((vec & CPMVEC_OFFSET) != 0) {
- /* CPM interrupt */
- vec &= 0xffff;
- if (cpm_vecs[vec].handler != NULL) {
- printf ("CPM interrupt 0x%x replacing 0x%x\n",
- (uint) handler,
- (uint) cpm_vecs[vec].handler);
- }
- cpm_vecs[vec].handler = handler;
- cpm_vecs[vec].arg = arg;
- immr->im_cpic.cpic_cimr |= (1 << vec);
-#if 0
- printf ("Install CPM interrupt for vector %d ==> %p\n",
- vec, handler);
-#endif
- } else {
- /* SIU interrupt */
- if (irq_vecs[vec].handler != NULL) {
- printf ("SIU interrupt %d 0x%x replacing 0x%x\n",
- vec,
- (uint) handler,
- (uint) cpm_vecs[vec].handler);
- }
- irq_vecs[vec].handler = handler;
- irq_vecs[vec].arg = arg;
- immr->im_siu_conf.sc_simask |= 1 << (31 - vec);
-#if 0
- printf ("Install SIU interrupt for vector %d ==> %p\n",
- vec, handler);
-#endif
- }
-}
-
-void irq_free_handler (int vec)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- if ((vec & CPMVEC_OFFSET) != 0) {
- /* CPM interrupt */
- vec &= 0xffff;
-#if 0
- printf ("Free CPM interrupt for vector %d ==> %p\n",
- vec, cpm_vecs[vec].handler);
-#endif
- immr->im_cpic.cpic_cimr &= ~(1 << vec);
- cpm_vecs[vec].handler = NULL;
- cpm_vecs[vec].arg = NULL;
- } else {
- /* SIU interrupt */
-#if 0
- printf ("Free CPM interrupt for vector %d ==> %p\n",
- vec, cpm_vecs[vec].handler);
-#endif
- immr->im_siu_conf.sc_simask &= ~(1 << (31 - vec));
- irq_vecs[vec].handler = NULL;
- irq_vecs[vec].arg = NULL;
- }
-}
-
-/************************************************************************/
-
-static void cpm_interrupt_init (void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- /*
- * Initialize the CPM interrupt controller.
- */
-
- immr->im_cpic.cpic_cicr =
- (CICR_SCD_SCC4 |
- CICR_SCC_SCC3 |
- CICR_SCB_SCC2 |
- CICR_SCA_SCC1) | ((CPM_INTERRUPT / 2) << 13) | CICR_HP_MASK;
-
- immr->im_cpic.cpic_cimr = 0;
-
- /*
- * Install the error handler.
- */
- irq_install_handler (CPMVEC_ERROR, cpm_error_interrupt, NULL);
-
- immr->im_cpic.cpic_cicr |= CICR_IEN;
-
- /*
- * Install the cpm interrupt handler
- */
- irq_install_handler (CPM_INTERRUPT, cpm_interrupt, NULL);
-}
-
-/************************************************************************/
-
-/*
- * timer_interrupt - gets called when the decrementer overflows,
- * with interrupts disabled.
- * Trivial implementation - no need to be really accurate.
- */
-void timer_interrupt_cpu (struct pt_regs *regs)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
-#if 0
- printf ("*** Timer Interrupt *** ");
-#endif
- /* Reset Timer Expired and Timers Interrupt Status */
- immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
- __asm__ ("nop");
- /*
- Clear TEXPS (and TMIST on older chips). SPLSS (on older
- chips) is cleared too.
-
- Bitwise OR is a read-modify-write operation so ALL bits
- which are cleared by writing `1' would be cleared by
- operations like
-
- immr->im_clkrst.car_plprcr |= PLPRCR_TEXPS;
-
- The same can be achieved by simple writing of the PLPRCR
- to itself. If a bit value should be preserved, read the
- register, ZERO the bit and write, not OR, the result back.
- */
- immr->im_clkrst.car_plprcr = immr->im_clkrst.car_plprcr;
-}
-
-/************************************************************************/
diff --git a/arch/powerpc/cpu/mpc8xx/kgdb.S b/arch/powerpc/cpu/mpc8xx/kgdb.S
deleted file mode 100644
index 0ea1a06c7ab38f66651edb519f2b7b1944fddd25..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/kgdb.S
+++ /dev/null
@@ -1,54 +0,0 @@
-/*
- * Copyright (C) 2000 Murray Jensen <Murray.Jensen@cmst.csiro.au>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <command.h>
-#include <mpc8xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-
-#if defined(CONFIG_CMD_KGDB)
-
- /*
- * cache flushing routines for kgdb
- */
-
- .globl kgdb_flush_cache_all
-kgdb_flush_cache_all:
- lis r3, IDC_INVALL@h
- mtspr DC_CST, r3
- sync
- lis r3, IDC_INVALL@h
- mtspr IC_CST, r3
- SYNC
- blr
-
- .globl kgdb_flush_cache_range
-kgdb_flush_cache_range:
- li r5,CONFIG_SYS_CACHELINE_SIZE-1
- andc r3,r3,r5
- subf r4,r3,r4
- add r4,r4,r5
- srwi. r4,r4,CONFIG_SYS_CACHELINE_SHIFT
- beqlr
- mtctr r4
- mr r6,r3
-1: dcbst 0,r3
- addi r3,r3,CONFIG_SYS_CACHELINE_SIZE
- bdnz 1b
- sync /* wait for dcbst's to get to ram */
- mtctr r4
-2: icbi 0,r6
- addi r6,r6,CONFIG_SYS_CACHELINE_SIZE
- bdnz 2b
- SYNC
- blr
-
-#endif
diff --git a/arch/powerpc/cpu/mpc8xx/plprcr_write.S b/arch/powerpc/cpu/mpc8xx/plprcr_write.S
deleted file mode 100644
index e28292f5e2fb683fc14b0dbbdafae7d50bed66ad..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/plprcr_write.S
+++ /dev/null
@@ -1,119 +0,0 @@
-/*
- * (C) Copyright 2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <mpc8xx.h>
-#include <ppc_asm.tmpl>
-#include <asm/cache.h>
-
-#define CACHE_CMD_ENABLE 0x02000000
-#define CACHE_CMD_DISABLE 0x04000000
-#define CACHE_CMD_LOAD_LOCK 0x06000000
-#define CACHE_CMD_UNLOCK_LINE 0x08000000
-#define CACHE_CMD_UNLOCK_ALL 0x0A000000
-#define CACHE_CMD_INVALIDATE 0x0C000000
-#define SPEED_PLPRCR_WAIT_5CYC 150
-#define _CACHE_ALIGN_SIZE 16
-
-
- .text
- .align 2
- .globl plprcr_write_866
-
-/*
- * void plprcr_write_866 (long plprcr)
- * Write PLPRCR, including workaround for device errata SIU4 and SIU9.
- */
-
-plprcr_write_866:
- mfspr r10, LR /* save the Link Register value */
-
- /* turn instruction cache on (no MMU required for instructions)
- */
- lis r4, CACHE_CMD_ENABLE@h
- ori r4, r4, CACHE_CMD_ENABLE@l
- mtspr IC_CST, r4
- isync
-
- /* clear IC_CST error bits
- */
- mfspr r4, IC_CST
-
- bl plprcr_here
-
-plprcr_here:
- mflr r5
-
- /* calculate relocation offset
- */
- lis r4, plprcr_here@h
- ori r4, r4, plprcr_here@l
- sub r5, r5, r4
-
- /* calculate first address of this function
- */
- lis r6, plprcr_write_866@h
- ori r6, r6, plprcr_write_866@l
- add r6, r6, r5
-
- /* calculate end address of this function
- */
- lis r7, plprcr_end@h
- ori r7, r7, plprcr_end@l
- add r7, r7, r5
-
- /* load and lock code addresses
- */
- mr r5, r6
-
-plprcr_loop:
- mtspr IC_ADR, r5
- addi r5, r5, _CACHE_ALIGN_SIZE /* increment by one line */
-
- lis r4, CACHE_CMD_LOAD_LOCK@h
- ori r4, r4, CACHE_CMD_LOAD_LOCK@l
- mtspr IC_CST, r4
- isync
-
- cmpw r5, r7
- blt plprcr_loop
-
- /* IC_CST error bits not evaluated
- */
-
- /* switch PLPRCR
- */
- mfspr r4, IMMR /* read IMMR */
- rlwinm r4, r4, 0, 0, 15 /* only high 16 bits count */
-
- /* write sequence according to MPC866 Errata
- */
- stw r3, PLPRCR(r4)
- isync
-
- lis r3, SPEED_PLPRCR_WAIT_5CYC@h
- ori r3, r3, SPEED_PLPRCR_WAIT_5CYC@l
-
-plprcr_wait:
- cmpwi r3, 0
- beq plprcr_wait_end
- nop
- subi r3, r3, 1
- b plprcr_wait
-
-plprcr_wait_end:
-
- /* unlock instruction cache but leave it enabled
- */
- lis r4, CACHE_CMD_UNLOCK_ALL@h
- ori r4, r4, CACHE_CMD_UNLOCK_ALL@l
- mtspr IC_CST, r4
- isync
-
- mtspr LR, r10 /* restore original Link Register value */
- blr
-
-plprcr_end:
diff --git a/arch/powerpc/cpu/mpc8xx/scc.c b/arch/powerpc/cpu/mpc8xx/scc.c
deleted file mode 100644
index 17bcc2fe0a14ef0cadbe660dcf04e0285c9bc615..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/scc.c
+++ /dev/null
@@ -1,472 +0,0 @@
-/*
- * File: scc.c
- * Description:
- * Basic ET HW initialization and packet RX/TX routines
- *
- * NOTE <<<IMPORTANT: PLEASE READ>>>:
- * Do not cache Rx/Tx buffers!
- */
-
-/*
- * MPC823 <-> MC68160 Connections:
- *
- * Setup MPC823 to work with MC68160 Enhanced Ethernet
- * Serial Tranceiver as follows:
- *
- * MPC823 Signal MC68160 Comments
- * ------ ------ ------- --------
- * PA-12 ETHTX --------> TX Eth. Port Transmit Data
- * PB-18 E_TENA --------> TENA Eth. Transmit Port Enable
- * PA-5 ETHTCK <-------- TCLK Eth. Port Transmit Clock
- * PA-13 ETHRX <-------- RX Eth. Port Receive Data
- * PC-8 E_RENA <-------- RENA Eth. Receive Enable
- * PA-6 ETHRCK <-------- RCLK Eth. Port Receive Clock
- * PC-9 E_CLSN <-------- CLSN Eth. Port Collision Indication
- *
- * FADS Board Signal MC68160 Comments
- * ----------------- ------- --------
- * (BCSR1) ETHEN* --------> CS2 Eth. Port Enable
- * (BSCR4) TPSQEL* --------> TPSQEL Twisted Pair Signal Quality Error Test Enable
- * (BCSR4) TPFLDL* --------> TPFLDL Twisted Pair Full-Duplex
- * (BCSR4) ETHLOOP --------> LOOP Eth. Port Diagnostic Loop-Back
- *
- */
-
-#include <common.h>
-#include <malloc.h>
-#include <commproc.h>
-#include <net.h>
-#include <command.h>
-
-#if defined(CONFIG_CMD_NET) && defined(SCC_ENET)
-
-/* Ethernet Transmit and Receive Buffers */
-#define DBUF_LENGTH 1520
-
-#define TX_BUF_CNT 2
-
-#define TOUT_LOOP 10000 /* 10 ms to have a packet sent */
-
-static char txbuf[DBUF_LENGTH];
-
-static uint rxIdx; /* index of the current RX buffer */
-static uint txIdx; /* index of the current TX buffer */
-
-/*
- * SCC Ethernet Tx and Rx buffer descriptors allocated at the
- * immr->udata_bd address on Dual-Port RAM
- * Provide for Double Buffering
- */
-
-typedef volatile struct CommonBufferDescriptor {
- cbd_t rxbd[PKTBUFSRX]; /* Rx BD */
- cbd_t txbd[TX_BUF_CNT]; /* Tx BD */
-} RTXBD;
-
-static RTXBD *rtx;
-
-static int scc_send(struct eth_device *dev, void *packet, int length);
-static int scc_recv(struct eth_device* dev);
-static int scc_init (struct eth_device* dev, bd_t * bd);
-static void scc_halt(struct eth_device* dev);
-
-int scc_initialize(bd_t *bis)
-{
- struct eth_device* dev;
-
- dev = (struct eth_device*) malloc(sizeof *dev);
- memset(dev, 0, sizeof *dev);
-
- strcpy(dev->name, "SCC");
- dev->iobase = 0;
- dev->priv = 0;
- dev->init = scc_init;
- dev->halt = scc_halt;
- dev->send = scc_send;
- dev->recv = scc_recv;
-
- eth_register(dev);
-
- return 1;
-}
-
-static int scc_send(struct eth_device *dev, void *packet, int length)
-{
- int i, j=0;
-#if 0
- volatile char *in, *out;
-#endif
-
- /* section 16.9.23.3
- * Wait for ready
- */
-#if 0
- while (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY);
- out = (char *)(rtx->txbd[txIdx].cbd_bufaddr);
- in = packet;
- for(i = 0; i < length; i++) {
- *out++ = *in++;
- }
- rtx->txbd[txIdx].cbd_datlen = length;
- rtx->txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST);
- while (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) j++;
-
-#ifdef ET_DEBUG
- printf("cycles: %d status: %x\n", j, rtx->txbd[txIdx].cbd_sc);
-#endif
- i = (rtx->txbd[txIdx++].cbd_sc & BD_ENET_TX_STATS) /* return only status bits */;
-
- /* wrap around buffer index when necessary */
- if (txIdx >= TX_BUF_CNT) txIdx = 0;
-#endif
-
- while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
- udelay (1); /* will also trigger Wd if needed */
- j++;
- }
- if (j>=TOUT_LOOP) printf("TX not ready\n");
- rtx->txbd[txIdx].cbd_bufaddr = (uint)packet;
- rtx->txbd[txIdx].cbd_datlen = length;
- rtx->txbd[txIdx].cbd_sc |= (BD_ENET_TX_READY | BD_ENET_TX_LAST |BD_ENET_TX_WRAP);
- while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
- udelay (1); /* will also trigger Wd if needed */
- j++;
- }
- if (j>=TOUT_LOOP) printf("TX timeout\n");
-#ifdef ET_DEBUG
- printf("cycles: %d status: %x\n", j, rtx->txbd[txIdx].cbd_sc);
-#endif
- i = (rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_STATS) /* return only status bits */;
- return i;
-}
-
-static int scc_recv (struct eth_device *dev)
-{
- int length;
-
- for (;;) {
- /* section 16.9.23.2 */
- if (rtx->rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
- length = -1;
- break; /* nothing received - leave for() loop */
- }
-
- length = rtx->rxbd[rxIdx].cbd_datlen;
-
- if (rtx->rxbd[rxIdx].cbd_sc & 0x003f) {
-#ifdef ET_DEBUG
- printf ("err: %x\n", rtx->rxbd[rxIdx].cbd_sc);
-#endif
- } else {
- /* Pass the packet up to the protocol layers. */
- net_process_received_packet(net_rx_packets[rxIdx],
- length - 4);
- }
-
-
- /* Give the buffer back to the SCC. */
- rtx->rxbd[rxIdx].cbd_datlen = 0;
-
- /* wrap around buffer index when necessary */
- if ((rxIdx + 1) >= PKTBUFSRX) {
- rtx->rxbd[PKTBUFSRX - 1].cbd_sc =
- (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
- rxIdx = 0;
- } else {
- rtx->rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
- rxIdx++;
- }
- }
- return length;
-}
-
-/**************************************************************
- *
- * SCC Ethernet Initialization Routine
- *
- *************************************************************/
-
-static int scc_init (struct eth_device *dev, bd_t * bis)
-{
-
- int i;
- scc_enet_t *pram_ptr;
-
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- pram_ptr = (scc_enet_t *) & (immr->im_cpm.cp_dparam[PROFF_ENET]);
-
- rxIdx = 0;
- txIdx = 0;
-
- if (!rtx)
- rtx = (RTXBD *)(immr->im_cpm.cp_dpmem + CPM_SCC_BASE);
-
-#if (defined(PA_ENET_RXD) && defined(PA_ENET_TXD))
- /* Configure port A pins for Txd and Rxd.
- */
- immr->im_ioport.iop_papar |= (PA_ENET_RXD | PA_ENET_TXD);
- immr->im_ioport.iop_padir &= ~(PA_ENET_RXD | PA_ENET_TXD);
- immr->im_ioport.iop_paodr &= ~PA_ENET_TXD;
-#elif (defined(PB_ENET_RXD) && defined(PB_ENET_TXD))
- /* Configure port B pins for Txd and Rxd.
- */
- immr->im_cpm.cp_pbpar |= (PB_ENET_RXD | PB_ENET_TXD);
- immr->im_cpm.cp_pbdir &= ~(PB_ENET_RXD | PB_ENET_TXD);
- immr->im_cpm.cp_pbodr &= ~PB_ENET_TXD;
-#else
-#error Configuration Error: exactly ONE of PA_ENET_[RT]XD, PB_ENET_[RT]XD must be defined
-#endif
-
-#if defined(PC_ENET_LBK)
- /* Configure port C pins to disable External Loopback
- */
- immr->im_ioport.iop_pcpar &= ~PC_ENET_LBK;
- immr->im_ioport.iop_pcdir |= PC_ENET_LBK;
- immr->im_ioport.iop_pcso &= ~PC_ENET_LBK;
- immr->im_ioport.iop_pcdat &= ~PC_ENET_LBK; /* Disable Loopback */
-#endif /* PC_ENET_LBK */
-
- /* Configure port C pins to enable CLSN and RENA.
- */
- immr->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
- immr->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
- immr->im_ioport.iop_pcso |= (PC_ENET_CLSN | PC_ENET_RENA);
-
- /* Configure port A for TCLK and RCLK.
- */
- immr->im_ioport.iop_papar |= (PA_ENET_TCLK | PA_ENET_RCLK);
- immr->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
-
- /*
- * Configure Serial Interface clock routing -- see section 16.7.5.3
- * First, clear all SCC bits to zero, then set the ones we want.
- */
-
- immr->im_cpm.cp_sicr &= ~SICR_ENET_MASK;
- immr->im_cpm.cp_sicr |= SICR_ENET_CLKRT;
-
-
- /*
- * Initialize SDCR -- see section 16.9.23.7
- * SDMA configuration register
- */
- immr->im_siu_conf.sc_sdcr = 0x01;
-
-
- /*
- * Setup SCC Ethernet Parameter RAM
- */
-
- pram_ptr->sen_genscc.scc_rfcr = 0x18; /* Normal Operation and Mot byte ordering */
- pram_ptr->sen_genscc.scc_tfcr = 0x18; /* Mot byte ordering, Normal access */
-
- pram_ptr->sen_genscc.scc_mrblr = DBUF_LENGTH; /* max. ET package len 1520 */
-
- pram_ptr->sen_genscc.scc_rbase = (unsigned int) (&rtx->rxbd[0]); /* Set RXBD tbl start at Dual Port */
- pram_ptr->sen_genscc.scc_tbase = (unsigned int) (&rtx->txbd[0]); /* Set TXBD tbl start at Dual Port */
-
- /*
- * Setup Receiver Buffer Descriptors (13.14.24.18)
- * Settings:
- * Empty, Wrap
- */
-
- for (i = 0; i < PKTBUFSRX; i++) {
- rtx->rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
- rtx->rxbd[i].cbd_datlen = 0; /* Reset */
- rtx->rxbd[i].cbd_bufaddr = (uint) net_rx_packets[i];
- }
-
- rtx->rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;
-
- /*
- * Setup Ethernet Transmitter Buffer Descriptors (13.14.24.19)
- * Settings:
- * Add PADs to Short FRAMES, Wrap, Last, Tx CRC
- */
-
- for (i = 0; i < TX_BUF_CNT; i++) {
- rtx->txbd[i].cbd_sc =
- (BD_ENET_TX_PAD | BD_ENET_TX_LAST | BD_ENET_TX_TC);
- rtx->txbd[i].cbd_datlen = 0; /* Reset */
- rtx->txbd[i].cbd_bufaddr = (uint) (&txbuf[0]);
- }
-
- rtx->txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
-
- /*
- * Enter Command: Initialize Rx Params for SCC
- */
-
- do { /* Spin until ready to issue command */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
- /* Issue command */
- immr->im_cpm.cp_cpcr =
- ((CPM_CR_INIT_RX << 8) | (CPM_CR_ENET << 4) | CPM_CR_FLG);
- do { /* Spin until command processed */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
-
- /*
- * Ethernet Specific Parameter RAM
- * see table 13-16, pg. 660,
- * pg. 681 (example with suggested settings)
- */
-
- pram_ptr->sen_cpres = ~(0x0); /* Preset CRC */
- pram_ptr->sen_cmask = 0xdebb20e3; /* Constant Mask for CRC */
- pram_ptr->sen_crcec = 0x0; /* Error Counter CRC (unused) */
- pram_ptr->sen_alec = 0x0; /* Alignment Error Counter (unused) */
- pram_ptr->sen_disfc = 0x0; /* Discard Frame Counter (unused) */
- pram_ptr->sen_pads = 0x8888; /* Short Frame PAD Characters */
-
- pram_ptr->sen_retlim = 15; /* Retry Limit Threshold */
- pram_ptr->sen_maxflr = 1518; /* MAX Frame Length Register */
- pram_ptr->sen_minflr = 64; /* MIN Frame Length Register */
-
- pram_ptr->sen_maxd1 = DBUF_LENGTH; /* MAX DMA1 Length Register */
- pram_ptr->sen_maxd2 = DBUF_LENGTH; /* MAX DMA2 Length Register */
-
- pram_ptr->sen_gaddr1 = 0x0; /* Group Address Filter 1 (unused) */
- pram_ptr->sen_gaddr2 = 0x0; /* Group Address Filter 2 (unused) */
- pram_ptr->sen_gaddr3 = 0x0; /* Group Address Filter 3 (unused) */
- pram_ptr->sen_gaddr4 = 0x0; /* Group Address Filter 4 (unused) */
-
-#define ea eth_get_ethaddr()
- pram_ptr->sen_paddrh = (ea[5] << 8) + ea[4];
- pram_ptr->sen_paddrm = (ea[3] << 8) + ea[2];
- pram_ptr->sen_paddrl = (ea[1] << 8) + ea[0];
-#undef ea
-
- pram_ptr->sen_pper = 0x0; /* Persistence (unused) */
- pram_ptr->sen_iaddr1 = 0x0; /* Individual Address Filter 1 (unused) */
- pram_ptr->sen_iaddr2 = 0x0; /* Individual Address Filter 2 (unused) */
- pram_ptr->sen_iaddr3 = 0x0; /* Individual Address Filter 3 (unused) */
- pram_ptr->sen_iaddr4 = 0x0; /* Individual Address Filter 4 (unused) */
- pram_ptr->sen_taddrh = 0x0; /* Tmp Address (MSB) (unused) */
- pram_ptr->sen_taddrm = 0x0; /* Tmp Address (unused) */
- pram_ptr->sen_taddrl = 0x0; /* Tmp Address (LSB) (unused) */
-
- /*
- * Enter Command: Initialize Tx Params for SCC
- */
-
- do { /* Spin until ready to issue command */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
- /* Issue command */
- immr->im_cpm.cp_cpcr =
- ((CPM_CR_INIT_TX << 8) | (CPM_CR_ENET << 4) | CPM_CR_FLG);
- do { /* Spin until command processed */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
-
- /*
- * Mask all Events in SCCM - we use polling mode
- */
- immr->im_cpm.cp_scc[SCC_ENET].scc_sccm = 0;
-
- /*
- * Clear Events in SCCE -- Clear bits by writing 1's
- */
-
- immr->im_cpm.cp_scc[SCC_ENET].scc_scce = ~(0x0);
-
-
- /*
- * Initialize GSMR High 32-Bits
- * Settings: Normal Mode
- */
-
- immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrh = 0;
-
- /*
- * Initialize GSMR Low 32-Bits, but do not Enable Transmit/Receive
- * Settings:
- * TCI = Invert
- * TPL = 48 bits
- * TPP = Repeating 10's
- * MODE = Ethernet
- */
-
- immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl = (SCC_GSMRL_TCI |
- SCC_GSMRL_TPL_48 |
- SCC_GSMRL_TPP_10 |
- SCC_GSMRL_MODE_ENET);
-
- /*
- * Initialize the DSR -- see section 13.14.4 (pg. 513) v0.4
- */
-
- immr->im_cpm.cp_scc[SCC_ENET].scc_dsr = 0xd555;
-
- /*
- * Initialize the PSMR
- * Settings:
- * CRC = 32-Bit CCITT
- * NIB = Begin searching for SFD 22 bits after RENA
- * FDE = Full Duplex Enable
- * LPB = Loopback Enable (Needed when FDE is set)
- * BRO = Reject broadcast packets
- * PROMISCOUS = Catch all packets regardless of dest. MAC adress
- */
- immr->im_cpm.cp_scc[SCC_ENET].scc_psmr = SCC_PSMR_ENCRC |
- SCC_PSMR_NIB22 |
-#if defined(CONFIG_SCC_ENET_FULL_DUPLEX)
- SCC_PSMR_FDE | SCC_PSMR_LPB |
-#endif
-#if defined(CONFIG_SCC_ENET_NO_BROADCAST)
- SCC_PSMR_BRO |
-#endif
-#if defined(CONFIG_SCC_ENET_PROMISCOUS)
- SCC_PSMR_PRO |
-#endif
- 0;
-
- /*
- * Configure Ethernet TENA Signal
- */
-
-#if (defined(PC_ENET_TENA) && !defined(PB_ENET_TENA))
- immr->im_ioport.iop_pcpar |= PC_ENET_TENA;
- immr->im_ioport.iop_pcdir &= ~PC_ENET_TENA;
-#elif (defined(PB_ENET_TENA) && !defined(PC_ENET_TENA))
- immr->im_cpm.cp_pbpar |= PB_ENET_TENA;
- immr->im_cpm.cp_pbdir |= PB_ENET_TENA;
-#else
-#error Configuration Error: exactly ONE of PB_ENET_TENA, PC_ENET_TENA must be defined
-#endif
-
- /*
- * Set the ENT/ENR bits in the GSMR Low -- Enable Transmit/Receive
- */
-
- immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |=
- (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
- return 1;
-}
-
-
-static void scc_halt (struct eth_device *dev)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
- immr->im_ioport.iop_pcso &= ~(PC_ENET_CLSN | PC_ENET_RENA);
-}
-
-#if 0
-void restart (void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl |=
- (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-}
-#endif
-#endif
diff --git a/arch/powerpc/cpu/mpc8xx/serial.c b/arch/powerpc/cpu/mpc8xx/serial.c
deleted file mode 100644
index b6e12d0d854fae3f2b347b81f73e4885e21bc1b4..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/serial.c
+++ /dev/null
@@ -1,676 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <commproc.h>
-#include <command.h>
-#include <serial.h>
-#include <watchdog.h>
-#include <linux/compiler.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if !defined(CONFIG_8xx_CONS_NONE) /* No Console at all */
-
-#if defined(CONFIG_8xx_CONS_SMC1) /* Console on SMC1 */
-#define SMC_INDEX 0
-#define PROFF_SMC PROFF_SMC1
-#define CPM_CR_CH_SMC CPM_CR_CH_SMC1
-
-#elif defined(CONFIG_8xx_CONS_SMC2) /* Console on SMC2 */
-#define SMC_INDEX 1
-#define PROFF_SMC PROFF_SMC2
-#define CPM_CR_CH_SMC CPM_CR_CH_SMC2
-
-#endif /* CONFIG_8xx_CONS_SMCx */
-
-#if defined(CONFIG_8xx_CONS_SCC1) /* Console on SCC1 */
-#define SCC_INDEX 0
-#define PROFF_SCC PROFF_SCC1
-#define CPM_CR_CH_SCC CPM_CR_CH_SCC1
-
-#elif defined(CONFIG_8xx_CONS_SCC2) /* Console on SCC2 */
-#define SCC_INDEX 1
-#define PROFF_SCC PROFF_SCC2
-#define CPM_CR_CH_SCC CPM_CR_CH_SCC2
-
-#elif defined(CONFIG_8xx_CONS_SCC3) /* Console on SCC3 */
-#define SCC_INDEX 2
-#define PROFF_SCC PROFF_SCC3
-#define CPM_CR_CH_SCC CPM_CR_CH_SCC3
-
-#elif defined(CONFIG_8xx_CONS_SCC4) /* Console on SCC4 */
-#define SCC_INDEX 3
-#define PROFF_SCC PROFF_SCC4
-#define CPM_CR_CH_SCC CPM_CR_CH_SCC4
-
-#endif /* CONFIG_8xx_CONS_SCCx */
-
-#if !defined(CONFIG_SYS_SMC_RXBUFLEN)
-#define CONFIG_SYS_SMC_RXBUFLEN 1
-#define CONFIG_SYS_MAXIDLE 0
-#else
-#if !defined(CONFIG_SYS_MAXIDLE)
-#error "you must define CONFIG_SYS_MAXIDLE"
-#endif
-#endif
-
-typedef volatile struct serialbuffer {
- cbd_t rxbd; /* Rx BD */
- cbd_t txbd; /* Tx BD */
- uint rxindex; /* index for next character to read */
- volatile uchar rxbuf[CONFIG_SYS_SMC_RXBUFLEN];/* rx buffers */
- volatile uchar txbuf; /* tx buffers */
-} serialbuffer_t;
-
-static void serial_setdivisor(volatile cpm8xx_t *cp)
-{
- int divisor=(gd->cpu_clk + 8*gd->baudrate)/16/gd->baudrate;
-
- if(divisor/16>0x1000) {
- /* bad divisor, assume 50MHz clock and 9600 baud */
- divisor=(50*1000*1000 + 8*9600)/16/9600;
- }
-
-#ifdef CONFIG_SYS_BRGCLK_PRESCALE
- divisor /= CONFIG_SYS_BRGCLK_PRESCALE;
-#endif
-
- if(divisor<=0x1000) {
- cp->cp_brgc1=((divisor-1)<<1) | CPM_BRG_EN;
- } else {
- cp->cp_brgc1=((divisor/16-1)<<1) | CPM_BRG_EN | CPM_BRG_DIV16;
- }
-}
-
-#if (defined (CONFIG_8xx_CONS_SMC1) || defined (CONFIG_8xx_CONS_SMC2))
-
-/*
- * Minimal serial functions needed to use one of the SMC ports
- * as serial console interface.
- */
-
-static void smc_setbrg (void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(im->im_cpm);
-
- /* Set up the baud rate generator.
- * See 8xx_io/commproc.c for details.
- *
- * Wire BRG1 to SMCx
- */
-
- cp->cp_simode = 0x00000000;
-
- serial_setdivisor(cp);
-}
-
-static int smc_init (void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile smc_t *sp;
- volatile smc_uart_t *up;
- volatile cpm8xx_t *cp = &(im->im_cpm);
-#if (!defined(CONFIG_8xx_CONS_SMC1)) && (defined(CONFIG_MPC823) || defined(CONFIG_MPC850))
- volatile iop8xx_t *ip = (iop8xx_t *)&(im->im_ioport);
-#endif
- uint dpaddr;
- volatile serialbuffer_t *rtx;
-
- /* initialize pointers to SMC */
-
- sp = (smc_t *) &(cp->cp_smc[SMC_INDEX]);
- up = (smc_uart_t *) &cp->cp_dparam[PROFF_SMC];
-#ifdef CONFIG_SYS_SMC_UCODE_PATCH
- up = (smc_uart_t *) &cp->cp_dpmem[up->smc_rpbase];
-#else
- /* Disable relocation */
- up->smc_rpbase = 0;
-#endif
-
- /* Disable transmitter/receiver. */
- sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
-
- /* Enable SDMA. */
- im->im_siu_conf.sc_sdcr = 1;
-
- /* clear error conditions */
-#ifdef CONFIG_SYS_SDSR
- im->im_sdma.sdma_sdsr = CONFIG_SYS_SDSR;
-#else
- im->im_sdma.sdma_sdsr = 0x83;
-#endif
-
- /* clear SDMA interrupt mask */
-#ifdef CONFIG_SYS_SDMR
- im->im_sdma.sdma_sdmr = CONFIG_SYS_SDMR;
-#else
- im->im_sdma.sdma_sdmr = 0x00;
-#endif
-
-#if defined(CONFIG_8xx_CONS_SMC1)
- /* Use Port B for SMC1 instead of other functions. */
- cp->cp_pbpar |= 0x000000c0;
- cp->cp_pbdir &= ~0x000000c0;
- cp->cp_pbodr &= ~0x000000c0;
-#else /* CONFIG_8xx_CONS_SMC2 */
-# if defined(CONFIG_MPC823) || defined(CONFIG_MPC850)
- /* Use Port A for SMC2 instead of other functions. */
- ip->iop_papar |= 0x00c0;
- ip->iop_padir &= ~0x00c0;
- ip->iop_paodr &= ~0x00c0;
-# else /* must be a 860 then */
- /* Use Port B for SMC2 instead of other functions.
- */
- cp->cp_pbpar |= 0x00000c00;
- cp->cp_pbdir &= ~0x00000c00;
- cp->cp_pbodr &= ~0x00000c00;
-# endif
-#endif
-
- /* Set the physical address of the host memory buffers in
- * the buffer descriptors.
- */
- dpaddr = CPM_SERIAL_BASE;
-
- rtx = (serialbuffer_t *)&cp->cp_dpmem[dpaddr];
- /* Allocate space for two buffer descriptors in the DP ram.
- * For now, this address seems OK, but it may have to
- * change with newer versions of the firmware.
- * damm: allocating space after the two buffers for rx/tx data
- */
-
- rtx->rxbd.cbd_bufaddr = (uint) &rtx->rxbuf;
- rtx->rxbd.cbd_sc = 0;
-
- rtx->txbd.cbd_bufaddr = (uint) &rtx->txbuf;
- rtx->txbd.cbd_sc = 0;
-
- /* Set up the uart parameters in the parameter ram. */
- up->smc_rbase = dpaddr;
- up->smc_tbase = dpaddr+sizeof(cbd_t);
- up->smc_rfcr = SMC_EB;
- up->smc_tfcr = SMC_EB;
-#if defined (CONFIG_SYS_SMC_UCODE_PATCH)
- up->smc_rbptr = up->smc_rbase;
- up->smc_tbptr = up->smc_tbase;
- up->smc_rstate = 0;
- up->smc_tstate = 0;
-#endif
-
- /* Set UART mode, 8 bit, no parity, one stop.
- * Enable receive and transmit.
- */
- sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
-
- /* Mask all interrupts and remove anything pending.
- */
- sp->smc_smcm = 0;
- sp->smc_smce = 0xff;
-
-#ifdef CONFIG_SYS_SPC1920_SMC1_CLK4
- /* clock source is PLD */
-
- /* set freq to 19200 Baud */
- *((volatile uchar *) CONFIG_SYS_SPC1920_PLD_BASE+6) = 0x3;
- /* configure clk4 as input */
- im->im_ioport.iop_pdpar |= 0x800;
- im->im_ioport.iop_pddir &= ~0x800;
-
- cp->cp_simode = ((cp->cp_simode & ~0xf000) | 0x7000);
-#else
- /* Set up the baud rate generator */
- smc_setbrg ();
-#endif
-
- /* Make the first buffer the only buffer. */
- rtx->txbd.cbd_sc |= BD_SC_WRAP;
- rtx->rxbd.cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
-
- /* single/multi character receive. */
- up->smc_mrblr = CONFIG_SYS_SMC_RXBUFLEN;
- up->smc_maxidl = CONFIG_SYS_MAXIDLE;
- rtx->rxindex = 0;
-
- /* Initialize Tx/Rx parameters. */
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SMC, CPM_CR_INIT_TRX) | CPM_CR_FLG;
-
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- /* Enable transmitter/receiver. */
- sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
-
- return (0);
-}
-
-static void
-smc_putc(const char c)
-{
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
- volatile serialbuffer_t *rtx;
-
- if (c == '\n')
- smc_putc ('\r');
-
- up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
-#ifdef CONFIG_SYS_SMC_UCODE_PATCH
- up = (smc_uart_t *) &cpmp->cp_dpmem[up->smc_rpbase];
-#endif
-
- rtx = (serialbuffer_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
- /* Wait for last character to go. */
- rtx->txbuf = c;
- rtx->txbd.cbd_datlen = 1;
- rtx->txbd.cbd_sc |= BD_SC_READY;
- __asm__("eieio");
-
- while (rtx->txbd.cbd_sc & BD_SC_READY) {
- WATCHDOG_RESET ();
- __asm__("eieio");
- }
-}
-
-static void
-smc_puts (const char *s)
-{
- while (*s) {
- smc_putc (*s++);
- }
-}
-
-static int
-smc_getc(void)
-{
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
- volatile serialbuffer_t *rtx;
- unsigned char c;
-
- up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
-#ifdef CONFIG_SYS_SMC_UCODE_PATCH
- up = (smc_uart_t *) &cpmp->cp_dpmem[up->smc_rpbase];
-#endif
- rtx = (serialbuffer_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
- /* Wait for character to show up. */
- while (rtx->rxbd.cbd_sc & BD_SC_EMPTY)
- WATCHDOG_RESET ();
-
- /* the characters are read one by one,
- * use the rxindex to know the next char to deliver
- */
- c = *(unsigned char *) (rtx->rxbd.cbd_bufaddr+rtx->rxindex);
- rtx->rxindex++;
-
- /* check if all char are readout, then make prepare for next receive */
- if (rtx->rxindex >= rtx->rxbd.cbd_datlen) {
- rtx->rxindex = 0;
- rtx->rxbd.cbd_sc |= BD_SC_EMPTY;
- }
- return(c);
-}
-
-static int
-smc_tstc(void)
-{
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
- volatile serialbuffer_t *rtx;
-
- up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
-#ifdef CONFIG_SYS_SMC_UCODE_PATCH
- up = (smc_uart_t *) &cpmp->cp_dpmem[up->smc_rpbase];
-#endif
-
- rtx = (serialbuffer_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
- return !(rtx->rxbd.cbd_sc & BD_SC_EMPTY);
-}
-
-struct serial_device serial_smc_device =
-{
- .name = "serial_smc",
- .start = smc_init,
- .stop = NULL,
- .setbrg = smc_setbrg,
- .getc = smc_getc,
- .tstc = smc_tstc,
- .putc = smc_putc,
- .puts = smc_puts,
-};
-
-#endif /* CONFIG_8xx_CONS_SMC1 || CONFIG_8xx_CONS_SMC2 */
-
-#if defined(CONFIG_8xx_CONS_SCC1) || defined(CONFIG_8xx_CONS_SCC2) || \
- defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4)
-
-static void
-scc_setbrg (void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(im->im_cpm);
-
- /* Set up the baud rate generator.
- * See 8xx_io/commproc.c for details.
- *
- * Wire BRG1 to SCCx
- */
-
- cp->cp_sicr &= ~(0x000000FF << (8 * SCC_INDEX));
-
- serial_setdivisor(cp);
-}
-
-static int scc_init (void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile scc_t *sp;
- volatile scc_uart_t *up;
- volatile cbd_t *tbdf, *rbdf;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- uint dpaddr;
-#if (SCC_INDEX != 2) || !defined(CONFIG_MPC850)
- volatile iop8xx_t *ip = (iop8xx_t *)&(im->im_ioport);
-#endif
-
- /* initialize pointers to SCC */
-
- sp = (scc_t *) &(cp->cp_scc[SCC_INDEX]);
- up = (scc_uart_t *) &cp->cp_dparam[PROFF_SCC];
-
- /* Disable transmitter/receiver. */
- sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
-#if (SCC_INDEX == 2) && defined(CONFIG_MPC850)
- /*
- * The MPC850 has SCC3 on Port B
- */
- cp->cp_pbpar |= 0x06;
- cp->cp_pbdir &= ~0x06;
- cp->cp_pbodr &= ~0x06;
-
-#elif (SCC_INDEX < 2)
- /*
- * Standard configuration for SCC's is on Part A
- */
- ip->iop_papar |= ((3 << (2 * SCC_INDEX)));
- ip->iop_padir &= ~((3 << (2 * SCC_INDEX)));
- ip->iop_paodr &= ~((3 << (2 * SCC_INDEX)));
-#endif
-
- /* Allocate space for two buffer descriptors in the DP ram. */
- dpaddr = dpram_alloc_align(sizeof(cbd_t)*2 + 2, 8);
-
- /* Enable SDMA. */
- im->im_siu_conf.sc_sdcr = 0x0001;
-
- /* Set the physical address of the host memory buffers in
- * the buffer descriptors.
- */
-
- rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
- rbdf->cbd_bufaddr = (uint) (rbdf+2);
- rbdf->cbd_sc = 0;
- tbdf = rbdf + 1;
- tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
- tbdf->cbd_sc = 0;
-
- /* Set up the baud rate generator. */
- scc_setbrg ();
-
- /* Set up the uart parameters in the parameter ram. */
- up->scc_genscc.scc_rbase = dpaddr;
- up->scc_genscc.scc_tbase = dpaddr+sizeof(cbd_t);
-
- /* Initialize Tx/Rx parameters. */
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SCC, CPM_CR_INIT_TRX) | CPM_CR_FLG;
-
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- up->scc_genscc.scc_rfcr = SCC_EB | 0x05;
- up->scc_genscc.scc_tfcr = SCC_EB | 0x05;
-
- up->scc_genscc.scc_mrblr = 1; /* Single character receive */
- up->scc_maxidl = 0; /* disable max idle */
- up->scc_brkcr = 1; /* send one break character on stop TX */
- up->scc_parec = 0;
- up->scc_frmec = 0;
- up->scc_nosec = 0;
- up->scc_brkec = 0;
- up->scc_uaddr1 = 0;
- up->scc_uaddr2 = 0;
- up->scc_toseq = 0;
- up->scc_char1 = 0x8000;
- up->scc_char2 = 0x8000;
- up->scc_char3 = 0x8000;
- up->scc_char4 = 0x8000;
- up->scc_char5 = 0x8000;
- up->scc_char6 = 0x8000;
- up->scc_char7 = 0x8000;
- up->scc_char8 = 0x8000;
- up->scc_rccm = 0xc0ff;
-
- /* Set low latency / small fifo. */
- sp->scc_gsmrh = SCC_GSMRH_RFW;
-
- /* Set SCC(x) clock mode to 16x
- * See 8xx_io/commproc.c for details.
- *
- * Wire BRG1 to SCCn
- */
-
- /* Set UART mode, clock divider 16 on Tx and Rx */
- sp->scc_gsmrl &= ~0xF;
- sp->scc_gsmrl |=
- (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
-
- sp->scc_psmr = 0;
- sp->scc_psmr |= SCU_PSMR_CL;
-
- /* Mask all interrupts and remove anything pending. */
- sp->scc_sccm = 0;
- sp->scc_scce = 0xffff;
- sp->scc_dsr = 0x7e7e;
- sp->scc_psmr = 0x3000;
-
- /* Make the first buffer the only buffer. */
- tbdf->cbd_sc |= BD_SC_WRAP;
- rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
-
- /* Enable transmitter/receiver. */
- sp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
- return (0);
-}
-
-static void
-scc_putc(const char c)
-{
- volatile cbd_t *tbdf;
- volatile char *buf;
- volatile scc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
-
- if (c == '\n')
- scc_putc ('\r');
-
- up = (scc_uart_t *)&cpmp->cp_dparam[PROFF_SCC];
-
- tbdf = (cbd_t *)&cpmp->cp_dpmem[up->scc_genscc.scc_tbase];
-
- /* Wait for last character to go. */
-
- buf = (char *)tbdf->cbd_bufaddr;
-
- *buf = c;
- tbdf->cbd_datlen = 1;
- tbdf->cbd_sc |= BD_SC_READY;
- __asm__("eieio");
-
- while (tbdf->cbd_sc & BD_SC_READY) {
- __asm__("eieio");
- WATCHDOG_RESET ();
- }
-}
-
-static void
-scc_puts (const char *s)
-{
- while (*s) {
- scc_putc (*s++);
- }
-}
-
-static int
-scc_getc(void)
-{
- volatile cbd_t *rbdf;
- volatile unsigned char *buf;
- volatile scc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
- unsigned char c;
-
- up = (scc_uart_t *)&cpmp->cp_dparam[PROFF_SCC];
-
- rbdf = (cbd_t *)&cpmp->cp_dpmem[up->scc_genscc.scc_rbase];
-
- /* Wait for character to show up. */
- buf = (unsigned char *)rbdf->cbd_bufaddr;
-
- while (rbdf->cbd_sc & BD_SC_EMPTY)
- WATCHDOG_RESET ();
-
- c = *buf;
- rbdf->cbd_sc |= BD_SC_EMPTY;
-
- return(c);
-}
-
-static int
-scc_tstc(void)
-{
- volatile cbd_t *rbdf;
- volatile scc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
-
- up = (scc_uart_t *)&cpmp->cp_dparam[PROFF_SCC];
-
- rbdf = (cbd_t *)&cpmp->cp_dpmem[up->scc_genscc.scc_rbase];
-
- return(!(rbdf->cbd_sc & BD_SC_EMPTY));
-}
-
-struct serial_device serial_scc_device =
-{
- .name = "serial_scc",
- .start = scc_init,
- .stop = NULL,
- .setbrg = scc_setbrg,
- .getc = scc_getc,
- .tstc = scc_tstc,
- .putc = scc_putc,
- .puts = scc_puts,
-};
-
-#endif /* CONFIG_8xx_CONS_SCCx */
-
-__weak struct serial_device *default_serial_console(void)
-{
-#if defined(CONFIG_8xx_CONS_SMC1) || defined(CONFIG_8xx_CONS_SMC2)
- return &serial_smc_device;
-#else
- return &serial_scc_device;
-#endif
-}
-
-void mpc8xx_serial_initialize(void)
-{
-#if defined(CONFIG_8xx_CONS_SMC1) || defined(CONFIG_8xx_CONS_SMC2)
- serial_register(&serial_smc_device);
-#endif
-#if defined(CONFIG_8xx_CONS_SCC1) || defined(CONFIG_8xx_CONS_SCC2) || \
- defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4)
- serial_register(&serial_scc_device);
-#endif
-}
-
-#if defined(CONFIG_CMD_KGDB)
-
-void
-kgdb_serial_init(void)
-{
- int i = -1;
-
- if (strcmp(default_serial_console()->name, "serial_smc") == 0)
- {
-#if defined(CONFIG_8xx_CONS_SMC1)
- i = 1;
-#elif defined(CONFIG_8xx_CONS_SMC2)
- i = 2;
-#endif
- }
- else if (strcmp(default_serial_console()->name, "serial_scc") == 0)
- {
-#if defined(CONFIG_8xx_CONS_SCC1)
- i = 1;
-#elif defined(CONFIG_8xx_CONS_SCC2)
- i = 2;
-#elif defined(CONFIG_8xx_CONS_SCC3)
- i = 3;
-#elif defined(CONFIG_8xx_CONS_SCC4)
- i = 4;
-#endif
- }
-
- if (i >= 0)
- {
- serial_printf("[on %s%d] ", default_serial_console()->name, i);
- }
-}
-
-void
-putDebugChar (int c)
-{
- serial_putc (c);
-}
-
-void
-putDebugStr (const char *str)
-{
- serial_puts (str);
-}
-
-int
-getDebugChar (void)
-{
- return serial_getc();
-}
-
-void
-kgdb_interruptible (int yes)
-{
- return;
-}
-#endif
-
-#endif /* CONFIG_8xx_CONS_NONE */
diff --git a/arch/powerpc/cpu/mpc8xx/speed.c b/arch/powerpc/cpu/mpc8xx/speed.c
deleted file mode 100644
index e2295d253f97dbbab203c4875784f5f08a4d1fd5..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/speed.c
+++ /dev/null
@@ -1,403 +0,0 @@
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <asm/processor.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if !defined(CONFIG_8xx_CPUCLK_DEFAULT) || defined(CONFIG_SYS_MEASURE_CPUCLK) || defined(DEBUG)
-
-#define PITC_SHIFT 16
-#define PITR_SHIFT 16
-/* pitc values to time for 58/8192 seconds (about 70.8 milliseconds) */
-#define SPEED_PIT_COUNTS 58
-#define SPEED_PITC ((SPEED_PIT_COUNTS - 1) << PITC_SHIFT)
-#define SPEED_PITC_INIT ((SPEED_PIT_COUNTS + 1) << PITC_SHIFT)
-
-/* Access functions for the Machine State Register */
-static __inline__ unsigned long get_msr(void)
-{
- unsigned long msr;
-
- asm volatile("mfmsr %0" : "=r" (msr) :);
- return msr;
-}
-
-static __inline__ void set_msr(unsigned long msr)
-{
- asm volatile("mtmsr %0" : : "r" (msr));
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Measure CPU clock speed (core clock GCLK1, GCLK2),
- * also determine bus clock speed (checking bus divider factor)
- *
- * (Approx. GCLK frequency in Hz)
- *
- * Initializes timer 2 and PIT, but disables them before return.
- * [Use timer 2, because MPC823 CPUs mask 0.x do not have timers 3 and 4]
- *
- * When measuring the CPU clock against the PIT, we count cpu clocks
- * for 58/8192 seconds with a prescale divide by 177 for the cpu clock.
- * These strange values for the timing interval and prescaling are used
- * because the formula for the CPU clock is:
- *
- * CPU clock = count * (177 * (8192 / 58))
- *
- * = count * 24999.7241
- *
- * which is very close to
- *
- * = count * 25000
- *
- * Since the count gives the CPU clock divided by 25000, we can get
- * the CPU clock rounded to the nearest 0.1 MHz by
- *
- * CPU clock = ((count + 2) / 4) * 100000;
- *
- * The rounding is important since the measurement is sometimes going
- * to be high or low by 0.025 MHz, depending on exactly how the clocks
- * and counters interact. By rounding we get the exact answer for any
- * CPU clock that is an even multiple of 0.1 MHz.
- */
-
-unsigned long measure_gclk(void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpmtimer8xx_t *timerp = &immr->im_cpmtimer;
- ulong timer2_val;
- ulong msr_val;
-
-#ifdef CONFIG_SYS_8XX_XIN
- /* dont use OSCM, only use EXTCLK/512 */
- immr->im_clkrst.car_sccr |= SCCR_RTSEL | SCCR_RTDIV;
-#else
- immr->im_clkrst.car_sccr &= ~(SCCR_RTSEL | SCCR_RTDIV);
-#endif
-
- /* Reset + Stop Timer 2, no cascading
- */
- timerp->cpmt_tgcr &= ~(TGCR_CAS2 | TGCR_RST2);
-
- /* Keep stopped, halt in debug mode
- */
- timerp->cpmt_tgcr |= (TGCR_FRZ2 | TGCR_STP2);
-
- /* Timer 2 setup:
- * Output ref. interrupt disable, int. clock
- * Prescale by 177. Note that prescaler divides by value + 1
- * so we must subtract 1 here.
- */
- timerp->cpmt_tmr2 = ((177 - 1) << TMR_PS_SHIFT) | TMR_ICLK_IN_GEN;
-
- timerp->cpmt_tcn2 = 0; /* reset state */
- timerp->cpmt_tgcr |= TGCR_RST2; /* enable timer 2 */
-
- /*
- * PIT setup:
- *
- * We want to time for SPEED_PITC_COUNTS counts (of 8192 Hz),
- * so the count value would be SPEED_PITC_COUNTS - 1.
- * But there would be an uncertainty in the start time of 1/4
- * count since when we enable the PIT the count is not
- * synchronized to the 32768 Hz oscillator. The trick here is
- * to start the count higher and wait until the PIT count
- * changes to the required value before starting timer 2.
- *
- * One count high should be enough, but occasionally the start
- * is off by 1 or 2 counts of 32768 Hz. With the start value
- * set two counts high it seems very reliable.
- */
-
- immr->im_sitk.sitk_pitck = KAPWR_KEY; /* PIT initialization */
- immr->im_sit.sit_pitc = SPEED_PITC_INIT;
-
- immr->im_sitk.sitk_piscrk = KAPWR_KEY;
- immr->im_sit.sit_piscr = CONFIG_SYS_PISCR;
-
- /*
- * Start measurement - disable interrupts, just in case
- */
- msr_val = get_msr ();
- set_msr (msr_val & ~MSR_EE);
-
- immr->im_sit.sit_piscr |= PISCR_PTE;
-
- /* spin until get exact count when we want to start */
- while (immr->im_sit.sit_pitr > SPEED_PITC);
-
- timerp->cpmt_tgcr &= ~TGCR_STP2; /* Start Timer 2 */
- while ((immr->im_sit.sit_piscr & PISCR_PS) == 0);
- timerp->cpmt_tgcr |= TGCR_STP2; /* Stop Timer 2 */
-
- /* re-enable external interrupts if they were on */
- set_msr (msr_val);
-
- /* Disable timer and PIT
- */
- timer2_val = timerp->cpmt_tcn2; /* save before reset timer */
-
- timerp->cpmt_tgcr &= ~(TGCR_RST2 | TGCR_FRZ2 | TGCR_STP2);
- immr->im_sit.sit_piscr &= ~PISCR_PTE;
-
-#if defined(CONFIG_SYS_8XX_XIN)
- /* not using OSCM, using XIN, so scale appropriately */
- return (((timer2_val + 2) / 4) * (CONFIG_SYS_8XX_XIN/512))/8192 * 100000L;
-#else
- return ((timer2_val + 2) / 4) * 100000L; /* convert to Hz */
-#endif
-}
-
-#endif
-
-void get_brgclk(uint sccr)
-{
- uint divider = 0;
-
- switch((sccr&SCCR_DFBRG11)>>11){
- case 0:
- divider = 1;
- break;
- case 1:
- divider = 4;
- break;
- case 2:
- divider = 16;
- break;
- case 3:
- divider = 64;
- break;
- }
- gd->arch.brg_clk = gd->cpu_clk/divider;
-}
-
-#if !defined(CONFIG_8xx_CPUCLK_DEFAULT)
-
-/*
- * get_clocks() fills in gd->cpu_clock depending on CONFIG_8xx_GCLK_FREQ
- * or (if it is not defined) measure_gclk() (which uses the ref clock)
- * from above.
- */
-int get_clocks (void)
-{
- uint immr = get_immr (0); /* Return full IMMR contents */
- volatile immap_t *immap = (immap_t *) (immr & 0xFFFF0000);
- uint sccr = immap->im_clkrst.car_sccr;
- /*
- * If for some reason measuring the gclk frequency won't
- * work, we return the hardwired value.
- * (For example, the cogent CMA286-60 CPU module has no
- * separate oscillator for PITRTCLK)
- */
-#if defined(CONFIG_8xx_GCLK_FREQ)
- gd->cpu_clk = CONFIG_8xx_GCLK_FREQ;
-#elif defined(CONFIG_8xx_OSCLK)
-#define PLPRCR_val(a) ((pll & PLPRCR_ ## a ## _MSK) >> PLPRCR_ ## a ## _SHIFT)
- uint pll = immap->im_clkrst.car_plprcr;
- uint clk;
-
- if ((immr & 0x0FFF) >= MPC8xx_NEW_CLK) { /* MPC866/87x/88x series */
- clk = ((CONFIG_8xx_OSCLK / (PLPRCR_val(PDF)+1)) *
- (PLPRCR_val(MFI) + PLPRCR_val(MFN) / (PLPRCR_val(MFD)+1))) /
- (1<<PLPRCR_val(S));
- } else {
- clk = CONFIG_8xx_OSCLK * (PLPRCR_val(MF)+1);
- }
- if (pll & PLPRCR_CSRC) { /* Low frequency division factor is used */
- gd->cpu_clk = clk / (2 << ((sccr >> 8) & 7));
- } else { /* High frequency division factor is used */
- gd->cpu_clk = clk / (1 << ((sccr >> 5) & 7));
- }
-#else
- gd->cpu_clk = measure_gclk();
-#endif /* CONFIG_8xx_GCLK_FREQ */
-
- if ((sccr & SCCR_EBDF11) == 0) {
- /* No Bus Divider active */
- gd->bus_clk = gd->cpu_clk;
- } else {
- /* The MPC8xx has only one BDF: half clock speed */
- gd->bus_clk = gd->cpu_clk / 2;
- }
-
- get_brgclk(sccr);
-
- return (0);
-}
-
-#else /* CONFIG_8xx_CPUCLK_DEFAULT defined, use dynamic clock setting */
-
-static long init_pll_866 (long clk);
-
-/* Adjust sdram refresh rate to actual CPU clock.
- */
-static int sdram_adjust_866(void)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- long mamr;
-
- mamr = immr->im_memctl.memc_mamr;
- mamr &= ~MAMR_PTA_MSK;
- mamr |= ((gd->cpu_clk / CONFIG_SYS_PTA_PER_CLK) << MAMR_PTA_SHIFT);
- immr->im_memctl.memc_mamr = mamr;
-
- return 0;
-}
-
-/*
- * Adjust sdram refresh rate to actual CPU clock
- * and set timebase source according to actual CPU clock
- */
-static int adjust_sdram_tbs_8xx(void)
-{
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) && \
- !defined(CONFIG_TQM885D)
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- long mamr;
- long sccr;
-
- mamr = immr->im_memctl.memc_mamr;
- mamr &= ~MAMR_PTA_MSK;
- mamr |= ((gd->cpu_clk / CONFIG_SYS_PTA_PER_CLK) << MAMR_PTA_SHIFT);
- immr->im_memctl.memc_mamr = mamr;
-
- if (gd->cpu_clk < 67000000) {
- sccr = immr->im_clkrst.car_sccr;
- sccr |= SCCR_TBS;
- immr->im_clkrst.car_sccr = sccr;
- }
-#endif /* CONFIG_TQM8xxL/M, !TQM866M, !TQM885D */
-
- return 0;
-}
-
-/* This function sets up PLL (init_pll_866() is called) and
- * fills gd->cpu_clk and gd->bus_clk according to the environment
- * variable 'cpuclk' or to CONFIG_8xx_CPUCLK_DEFAULT (if 'cpuclk'
- * contains invalid value).
- * This functions requires an MPC866 or newer series CPU.
- */
-int get_clocks(void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- char tmp[64];
- long cpuclk = 0;
- long sccr_reg;
- int ret;
-
- if (getenv_f("cpuclk", tmp, sizeof (tmp)) > 0)
- cpuclk = simple_strtoul (tmp, NULL, 10) * 1000000;
-
- if ((CONFIG_SYS_8xx_CPUCLK_MIN > cpuclk) || (CONFIG_SYS_8xx_CPUCLK_MAX < cpuclk))
- cpuclk = CONFIG_8xx_CPUCLK_DEFAULT;
-
- gd->cpu_clk = init_pll_866 (cpuclk);
-#if defined(CONFIG_SYS_MEASURE_CPUCLK)
- gd->cpu_clk = measure_gclk ();
-#endif
-
- get_brgclk(immr->im_clkrst.car_sccr);
-
- /* if cpu clock <= 66 MHz then set bus division factor to 1,
- * otherwise set it to 2
- */
- sccr_reg = immr->im_clkrst.car_sccr;
- sccr_reg &= ~SCCR_EBDF11;
-
- if (gd->cpu_clk <= 66000000) {
- sccr_reg |= SCCR_EBDF00; /* bus division factor = 1 */
- gd->bus_clk = gd->cpu_clk;
- } else {
- sccr_reg |= SCCR_EBDF01; /* bus division factor = 2 */
- gd->bus_clk = gd->cpu_clk / 2;
- }
- immr->im_clkrst.car_sccr = sccr_reg;
-
- ret = sdram_adjust_866();
- if (ret)
- return ret;
-
- return adjust_sdram_tbs_8xx();
-}
-
-/* Configure PLL for MPC866/859/885 CPU series
- * PLL multiplication factor is set to the value nearest to the desired clk,
- * assuming a oscclk of 10 MHz.
- */
-static long init_pll_866 (long clk)
-{
- extern void plprcr_write_866 (long);
-
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- long n, plprcr;
- char mfi, mfn, mfd, s, pdf;
- long step_mfi, step_mfn;
-
- if (clk < 20000000) {
- clk *= 2;
- pdf = 1;
- } else {
- pdf = 0;
- }
-
- if (clk < 40000000) {
- s = 2;
- step_mfi = CONFIG_8xx_OSCLK / 4;
- mfd = 7;
- step_mfn = CONFIG_8xx_OSCLK / 30;
- } else if (clk < 80000000) {
- s = 1;
- step_mfi = CONFIG_8xx_OSCLK / 2;
- mfd = 14;
- step_mfn = CONFIG_8xx_OSCLK / 30;
- } else {
- s = 0;
- step_mfi = CONFIG_8xx_OSCLK;
- mfd = 29;
- step_mfn = CONFIG_8xx_OSCLK / 30;
- }
-
- /* Calculate integer part of multiplication factor
- */
- n = clk / step_mfi;
- mfi = (char)n;
-
- /* Calculate numerator of fractional part of multiplication factor
- */
- n = clk - (n * step_mfi);
- mfn = (char)(n / step_mfn);
-
- /* Calculate effective clk
- */
- n = ((mfi * step_mfi) + (mfn * step_mfn)) / (pdf + 1);
-
- immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
-
- plprcr = (immr->im_clkrst.car_plprcr & ~(PLPRCR_MFN_MSK
- | PLPRCR_MFD_MSK | PLPRCR_S_MSK
- | PLPRCR_MFI_MSK | PLPRCR_DBRMO
- | PLPRCR_PDF_MSK))
- | (mfn << PLPRCR_MFN_SHIFT)
- | (mfd << PLPRCR_MFD_SHIFT)
- | (s << PLPRCR_S_SHIFT)
- | (mfi << PLPRCR_MFI_SHIFT)
- | (pdf << PLPRCR_PDF_SHIFT);
-
- if( (mfn > 0) && ((mfd / mfn) > 10) )
- plprcr |= PLPRCR_DBRMO;
-
- plprcr_write_866 (plprcr); /* set value using SIU4/9 workaround */
- immr->im_clkrstk.cark_plprcrk = 0x00000000;
-
- return (n);
-}
-
-#endif /* CONFIG_8xx_CPUCLK_DEFAULT */
diff --git a/arch/powerpc/cpu/mpc8xx/spi.c b/arch/powerpc/cpu/mpc8xx/spi.c
deleted file mode 100644
index 35b425e7c14783ac4b1c13be155686bb44652dfd..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/spi.c
+++ /dev/null
@@ -1,533 +0,0 @@
-/*
- * Copyright (c) 2001 Navin Boppuri / Prashant Patel
- * <nboppuri@trinetcommunication.com>,
- * <pmpatel@trinetcommunication.com>
- * Copyright (c) 2001 Gerd Mennchen <Gerd.Mennchen@icn.siemens.de>
- * Copyright (c) 2001 Wolfgang Denk, DENX Software Engineering, <wd@denx.de>.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * MPC8xx CPM SPI interface.
- *
- * Parts of this code are probably not portable and/or specific to
- * the board which I used for the tests. Please send fixes/complaints
- * to wd@denx.de
- *
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <commproc.h>
-#include <linux/ctype.h>
-#include <malloc.h>
-#include <post.h>
-#include <serial.h>
-
-#if (defined(CONFIG_SPI)) || (CONFIG_POST & CONFIG_SYS_POST_SPI)
-
-/* Warning:
- * You cannot enable DEBUG for early system initalization, i. e. when
- * this driver is used to read environment parameters like "baudrate"
- * from EEPROM which are used to initialize the serial port which is
- * needed to print the debug messages...
- */
-#undef DEBUG
-
-#define SPI_EEPROM_WREN 0x06
-#define SPI_EEPROM_RDSR 0x05
-#define SPI_EEPROM_READ 0x03
-#define SPI_EEPROM_WRITE 0x02
-
-/* ---------------------------------------------------------------
- * Offset for initial SPI buffers in DPRAM:
- * We need a 520 byte scratch DPRAM area to use at an early stage.
- * It is used between the two initialization calls (spi_init_f()
- * and spi_init_r()).
- * The value 0xb00 makes it far enough from the start of the data
- * area (as well as from the stack pointer).
- * --------------------------------------------------------------- */
-#ifndef CONFIG_SYS_SPI_INIT_OFFSET
-#define CONFIG_SYS_SPI_INIT_OFFSET 0xB00
-#endif
-
-#ifdef DEBUG
-
-#define DPRINT(a) printf a;
-/* -----------------------------------------------
- * Helper functions to peek into tx and rx buffers
- * ----------------------------------------------- */
-static const char * const hex_digit = "0123456789ABCDEF";
-
-static char quickhex (int i)
-{
- return hex_digit[i];
-}
-
-static void memdump (void *pv, int num)
-{
- int i;
- unsigned char *pc = (unsigned char *) pv;
-
- for (i = 0; i < num; i++)
- printf ("%c%c ", quickhex (pc[i] >> 4), quickhex (pc[i] & 0x0f));
- printf ("\t");
- for (i = 0; i < num; i++)
- printf ("%c", isprint (pc[i]) ? pc[i] : '.');
- printf ("\n");
-}
-#else /* !DEBUG */
-
-#define DPRINT(a)
-
-#endif /* DEBUG */
-
-/* -------------------
- * Function prototypes
- * ------------------- */
-void spi_init (void);
-
-ssize_t spi_read (uchar *, int, uchar *, int);
-ssize_t spi_write (uchar *, int, uchar *, int);
-ssize_t spi_xfer (size_t);
-
-/* -------------------
- * Variables
- * ------------------- */
-
-#define MAX_BUFFER 0x104
-
-/* ----------------------------------------------------------------------
- * Initially we place the RX and TX buffers at a fixed location in DPRAM!
- * ---------------------------------------------------------------------- */
-static uchar *rxbuf =
- (uchar *)&((cpm8xx_t *)&((immap_t *)CONFIG_SYS_IMMR)->im_cpm)->cp_dpmem
- [CONFIG_SYS_SPI_INIT_OFFSET];
-static uchar *txbuf =
- (uchar *)&((cpm8xx_t *)&((immap_t *)CONFIG_SYS_IMMR)->im_cpm)->cp_dpmem
- [CONFIG_SYS_SPI_INIT_OFFSET+MAX_BUFFER];
-
-/* **************************************************************************
- *
- * Function: spi_init_f
- *
- * Description: Init SPI-Controller (ROM part)
- *
- * return: ---
- *
- * *********************************************************************** */
-void spi_init_f (void)
-{
- unsigned int dpaddr;
-
- volatile spi_t *spi;
- volatile immap_t *immr;
- volatile cpm8xx_t *cp;
- volatile cbd_t *tbdf, *rbdf;
-
- immr = (immap_t *) CONFIG_SYS_IMMR;
- cp = (cpm8xx_t *) &immr->im_cpm;
-
-#ifdef CONFIG_SYS_SPI_UCODE_PATCH
- spi = (spi_t *)&cp->cp_dpmem[spi->spi_rpbase];
-#else
- spi = (spi_t *)&cp->cp_dparam[PROFF_SPI];
- /* Disable relocation */
- spi->spi_rpbase = 0;
-#endif
-
-/* 1 */
- /* ------------------------------------------------
- * Initialize Port B SPI pins -> page 34-8 MPC860UM
- * (we are only in Master Mode !)
- * ------------------------------------------------ */
-
- /* --------------------------------------------
- * GPIO or per. Function
- * PBPAR[28] = 1 [0x00000008] -> PERI: (SPIMISO)
- * PBPAR[29] = 1 [0x00000004] -> PERI: (SPIMOSI)
- * PBPAR[30] = 1 [0x00000002] -> PERI: (SPICLK)
- * PBPAR[31] = 0 [0x00000001] -> GPIO: (CS for PCUE/CCM-EEPROM)
- * -------------------------------------------- */
- cp->cp_pbpar |= 0x0000000E; /* set bits */
- cp->cp_pbpar &= ~0x00000001; /* reset bit */
-
- /* ----------------------------------------------
- * In/Out or per. Function 0/1
- * PBDIR[28] = 1 [0x00000008] -> PERI1: SPIMISO
- * PBDIR[29] = 1 [0x00000004] -> PERI1: SPIMOSI
- * PBDIR[30] = 1 [0x00000002] -> PERI1: SPICLK
- * PBDIR[31] = 1 [0x00000001] -> GPIO OUT: CS for PCUE/CCM-EEPROM
- * ---------------------------------------------- */
- cp->cp_pbdir |= 0x0000000F;
-
- /* ----------------------------------------------
- * open drain or active output
- * PBODR[28] = 1 [0x00000008] -> open drain: SPIMISO
- * PBODR[29] = 0 [0x00000004] -> active output SPIMOSI
- * PBODR[30] = 0 [0x00000002] -> active output: SPICLK
- * PBODR[31] = 0 [0x00000001] -> active output: GPIO OUT: CS for PCUE/CCM
- * ---------------------------------------------- */
-
- cp->cp_pbodr |= 0x00000008;
- cp->cp_pbodr &= ~0x00000007;
-
- /* Initialize the parameter ram.
- * We need to make sure many things are initialized to zero
- */
- spi->spi_rstate = 0;
- spi->spi_rdp = 0;
- spi->spi_rbptr = 0;
- spi->spi_rbc = 0;
- spi->spi_rxtmp = 0;
- spi->spi_tstate = 0;
- spi->spi_tdp = 0;
- spi->spi_tbptr = 0;
- spi->spi_tbc = 0;
- spi->spi_txtmp = 0;
-
- dpaddr = CPM_SPI_BASE;
-
-/* 3 */
- /* Set up the SPI parameters in the parameter ram */
- spi->spi_rbase = dpaddr;
- spi->spi_tbase = dpaddr + sizeof (cbd_t);
-
- /***********IMPORTANT******************/
-
- /*
- * Setting transmit and receive buffer descriptor pointers
- * initially to rbase and tbase. Only the microcode patches
- * documentation talks about initializing this pointer. This
- * is missing from the sample I2C driver. If you dont
- * initialize these pointers, the kernel hangs.
- */
- spi->spi_rbptr = spi->spi_rbase;
- spi->spi_tbptr = spi->spi_tbase;
-
-/* 4 */
-#ifdef CONFIG_SYS_SPI_UCODE_PATCH
- /*
- * Initialize required parameters if using microcode patch.
- */
- spi->spi_rstate = 0;
- spi->spi_tstate = 0;
-#else
- /* Init SPI Tx + Rx Parameters */
- while (cp->cp_cpcr & CPM_CR_FLG)
- ;
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SPI, CPM_CR_INIT_TRX) | CPM_CR_FLG;
- while (cp->cp_cpcr & CPM_CR_FLG)
- ;
-#endif /* CONFIG_SYS_SPI_UCODE_PATCH */
-
-/* 5 */
- /* Set SDMA configuration register */
- immr->im_siu_conf.sc_sdcr = 0x0001;
-
-/* 6 */
- /* Set to big endian. */
- spi->spi_tfcr = SMC_EB;
- spi->spi_rfcr = SMC_EB;
-
-/* 7 */
- /* Set maximum receive size. */
- spi->spi_mrblr = MAX_BUFFER;
-
-/* 8 + 9 */
- /* tx and rx buffer descriptors */
- tbdf = (cbd_t *) & cp->cp_dpmem[spi->spi_tbase];
- rbdf = (cbd_t *) & cp->cp_dpmem[spi->spi_rbase];
-
- tbdf->cbd_sc &= ~BD_SC_READY;
- rbdf->cbd_sc &= ~BD_SC_EMPTY;
-
- /* Set the bd's rx and tx buffer address pointers */
- rbdf->cbd_bufaddr = (ulong) rxbuf;
- tbdf->cbd_bufaddr = (ulong) txbuf;
-
-/* 10 + 11 */
- cp->cp_spim = 0; /* Mask all SPI events */
- cp->cp_spie = SPI_EMASK; /* Clear all SPI events */
-
- return;
-}
-
-/* **************************************************************************
- *
- * Function: spi_init_r
- *
- * Description: Init SPI-Controller (RAM part) -
- * The malloc engine is ready and we can move our buffers to
- * normal RAM
- *
- * return: ---
- *
- * *********************************************************************** */
-void spi_init_r (void)
-{
- volatile cpm8xx_t *cp;
- volatile spi_t *spi;
- volatile immap_t *immr;
- volatile cbd_t *tbdf, *rbdf;
-
- immr = (immap_t *) CONFIG_SYS_IMMR;
- cp = (cpm8xx_t *) &immr->im_cpm;
-
-#ifdef CONFIG_SYS_SPI_UCODE_PATCH
- spi = (spi_t *)&cp->cp_dpmem[spi->spi_rpbase];
-#else
- spi = (spi_t *)&cp->cp_dparam[PROFF_SPI];
- /* Disable relocation */
- spi->spi_rpbase = 0;
-#endif
-
- /* tx and rx buffer descriptors */
- tbdf = (cbd_t *) & cp->cp_dpmem[spi->spi_tbase];
- rbdf = (cbd_t *) & cp->cp_dpmem[spi->spi_rbase];
-
- /* Allocate memory for RX and TX buffers */
- rxbuf = (uchar *) malloc (MAX_BUFFER);
- txbuf = (uchar *) malloc (MAX_BUFFER);
-
- rbdf->cbd_bufaddr = (ulong) rxbuf;
- tbdf->cbd_bufaddr = (ulong) txbuf;
-
- return;
-}
-
-/****************************************************************************
- * Function: spi_write
- **************************************************************************** */
-ssize_t spi_write (uchar *addr, int alen, uchar *buffer, int len)
-{
- int i;
-
- memset(rxbuf, 0, MAX_BUFFER);
- memset(txbuf, 0, MAX_BUFFER);
- *txbuf = SPI_EEPROM_WREN; /* write enable */
- spi_xfer(1);
- memcpy(txbuf, addr, alen);
- *txbuf = SPI_EEPROM_WRITE; /* WRITE memory array */
- memcpy(alen + txbuf, buffer, len);
- spi_xfer(alen + len);
- /* ignore received data */
- for (i = 0; i < 1000; i++) {
- *txbuf = SPI_EEPROM_RDSR; /* read status */
- txbuf[1] = 0;
- spi_xfer(2);
- if (!(rxbuf[1] & 1)) {
- break;
- }
- udelay(1000);
- }
- if (i >= 1000) {
- printf ("*** spi_write: Time out while writing!\n");
- }
-
- return len;
-}
-
-/****************************************************************************
- * Function: spi_read
- **************************************************************************** */
-ssize_t spi_read (uchar *addr, int alen, uchar *buffer, int len)
-{
- memset(rxbuf, 0, MAX_BUFFER);
- memset(txbuf, 0, MAX_BUFFER);
- memcpy(txbuf, addr, alen);
- *txbuf = SPI_EEPROM_READ; /* READ memory array */
-
- /*
- * There is a bug in 860T (?) that cuts the last byte of input
- * if we're reading into DPRAM. The solution we choose here is
- * to always read len+1 bytes (we have one extra byte at the
- * end of the buffer).
- */
- spi_xfer(alen + len + 1);
- memcpy(buffer, alen + rxbuf, len);
-
- return len;
-}
-
-/****************************************************************************
- * Function: spi_xfer
- **************************************************************************** */
-ssize_t spi_xfer (size_t count)
-{
- volatile immap_t *immr;
- volatile cpm8xx_t *cp;
- volatile spi_t *spi;
- cbd_t *tbdf, *rbdf;
- ushort loop;
- int tm;
-
- DPRINT (("*** spi_xfer entered ***\n"));
-
- immr = (immap_t *) CONFIG_SYS_IMMR;
- cp = (cpm8xx_t *) &immr->im_cpm;
-
-#ifdef CONFIG_SYS_SPI_UCODE_PATCH
- spi = (spi_t *)&cp->cp_dpmem[spi->spi_rpbase];
-#else
- spi = (spi_t *)&cp->cp_dparam[PROFF_SPI];
- /* Disable relocation */
- spi->spi_rpbase = 0;
-#endif
-
- tbdf = (cbd_t *) & cp->cp_dpmem[spi->spi_tbase];
- rbdf = (cbd_t *) & cp->cp_dpmem[spi->spi_rbase];
-
- /* Set CS for device */
- cp->cp_pbdat &= ~0x0001;
-
- /* Setting tx bd status and data length */
- tbdf->cbd_sc = BD_SC_READY | BD_SC_LAST | BD_SC_WRAP;
- tbdf->cbd_datlen = count;
-
- DPRINT (("*** spi_xfer: Bytes to be xferred: %d ***\n",
- tbdf->cbd_datlen));
-
- /* Setting rx bd status and data length */
- rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
- rbdf->cbd_datlen = 0; /* rx length has no significance */
-
- loop = cp->cp_spmode & SPMODE_LOOP;
- cp->cp_spmode = /*SPMODE_DIV16 |*/ /* BRG/16 mode not used here */
- loop |
- SPMODE_REV |
- SPMODE_MSTR |
- SPMODE_EN |
- SPMODE_LEN(8) | /* 8 Bits per char */
- SPMODE_PM(0x8) ; /* medium speed */
- cp->cp_spim = 0; /* Mask all SPI events */
- cp->cp_spie = SPI_EMASK; /* Clear all SPI events */
-
- /* start spi transfer */
- DPRINT (("*** spi_xfer: Performing transfer ...\n"));
- cp->cp_spcom |= SPI_STR; /* Start transmit */
-
- /* --------------------------------
- * Wait for SPI transmit to get out
- * or time out (1 second = 1000 ms)
- * -------------------------------- */
- for (tm=0; tm<1000; ++tm) {
- if (cp->cp_spie & SPI_TXB) { /* Tx Buffer Empty */
- DPRINT (("*** spi_xfer: Tx buffer empty\n"));
- break;
- }
- if ((tbdf->cbd_sc & BD_SC_READY) == 0) {
- DPRINT (("*** spi_xfer: Tx BD done\n"));
- break;
- }
- udelay (1000);
- }
- if (tm >= 1000) {
- printf ("*** spi_xfer: Time out while xferring to/from SPI!\n");
- }
- DPRINT (("*** spi_xfer: ... transfer ended\n"));
-
-#ifdef DEBUG
- printf ("\nspi_xfer: txbuf after xfer\n");
- memdump ((void *) txbuf, 16); /* dump of txbuf before transmit */
- printf ("spi_xfer: rxbuf after xfer\n");
- memdump ((void *) rxbuf, 16); /* dump of rxbuf after transmit */
- printf ("\n");
-#endif
-
- /* Clear CS for device */
- cp->cp_pbdat |= 0x0001;
-
- return count;
-}
-#endif /* CONFIG_SPI || (CONFIG_POST & CONFIG_SYS_POST_SPI) */
-
-/*
- * SPI test
- *
- * The Serial Peripheral Interface (SPI) is tested in the local loopback mode.
- * The interface is configured accordingly and several packets
- * are transferred. The configurable test parameters are:
- * TEST_MIN_LENGTH - minimum size of packet to transfer
- * TEST_MAX_LENGTH - maximum size of packet to transfer
- * TEST_NUM - number of tests
- */
-
-#if CONFIG_POST & CONFIG_SYS_POST_SPI
-
-#define TEST_MIN_LENGTH 1
-#define TEST_MAX_LENGTH MAX_BUFFER
-#define TEST_NUM 1
-
-static void packet_fill (char * packet, int length)
-{
- char c = (char) length;
- int i;
-
- for (i = 0; i < length; i++)
- {
- packet[i] = c++;
- }
-}
-
-static int packet_check (char * packet, int length)
-{
- char c = (char) length;
- int i;
-
- for (i = 0; i < length; i++) {
- if (packet[i] != c++) return -1;
- }
-
- return 0;
-}
-
-int spi_post_test (int flags)
-{
- int res = -1;
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = (cpm8xx_t *) & immr->im_cpm;
- int i;
- int l;
-
- spi_init_f ();
- spi_init_r ();
-
- cp->cp_spmode |= SPMODE_LOOP;
-
- for (i = 0; i < TEST_NUM; i++) {
- for (l = TEST_MIN_LENGTH; l <= TEST_MAX_LENGTH; l += 8) {
- packet_fill ((char *)txbuf, l);
-
- spi_xfer (l);
-
- if (packet_check ((char *)rxbuf, l) < 0) {
- goto Done;
- }
- }
- }
-
- res = 0;
-
- Done:
-
- cp->cp_spmode &= ~SPMODE_LOOP;
-
- /*
- * SCC2 parameter RAM space overlaps
- * the SPI parameter RAM space. So we need to restore
- * the SCC2 configuration if it is used by UART.
- */
-
-#if !defined(CONFIG_8xx_CONS_NONE)
- serial_reinit_all ();
-#endif
-
- if (res != 0) {
- post_log ("SPI test failed\n");
- }
-
- return res;
-}
-#endif /* CONFIG_POST & CONFIG_SYS_POST_SPI */
diff --git a/arch/powerpc/cpu/mpc8xx/start.S b/arch/powerpc/cpu/mpc8xx/start.S
deleted file mode 100644
index f8aa93d6118269a012025bcfc146892b92b94da8..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/start.S
+++ /dev/null
@@ -1,650 +0,0 @@
-/*
- * Copyright (C) 1998 Dan Malek <dmalek@jlc.net>
- * Copyright (C) 1999 Magnus Damm <kieraypc01.p.y.kie.era.ericsson.se>
- * Copyright (C) 2000,2001,2002 Wolfgang Denk <wd@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* U-Boot - Startup Code for PowerPC based Embedded Boards
- *
- *
- * The processor starts at 0x00000100 and the code is executed
- * from flash. The code is organized to be at an other address
- * in memory, but as long we don't jump around before relocating,
- * board_init lies at a quite high address and when the cpu has
- * jumped there, everything is ok.
- * This works because the cpu gives the FLASH (CS0) the whole
- * address space at startup, and board_init lies as a echo of
- * the flash somewhere up there in the memory map.
- *
- * board_init will change CS0 to be positioned at the correct
- * address and (s)dram will be positioned at address 0
- */
-#include <asm-offsets.h>
-#include <config.h>
-#include <mpc8xx.h>
-#include <version.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-#include <asm/u-boot.h>
-
-/* We don't want the MMU yet.
-*/
-#undef MSR_KERNEL
-#define MSR_KERNEL ( MSR_ME | MSR_RI ) /* Machine Check and Recoverable Interr. */
-
-/*
- * Set up GOT: Global Offset Table
- *
- * Use r12 to access the GOT
- */
- START_GOT
- GOT_ENTRY(_GOT2_TABLE_)
- GOT_ENTRY(_FIXUP_TABLE_)
-
- GOT_ENTRY(_start)
- GOT_ENTRY(_start_of_vectors)
- GOT_ENTRY(_end_of_vectors)
- GOT_ENTRY(transfer_to_handler)
-
- GOT_ENTRY(__init_end)
- GOT_ENTRY(__bss_end)
- GOT_ENTRY(__bss_start)
- END_GOT
-
-/*
- * r3 - 1st arg to board_init(): IMMP pointer
- * r4 - 2nd arg to board_init(): boot flag
- */
- .text
- .long 0x27051956 /* U-Boot Magic Number */
- .globl version_string
-version_string:
- .ascii U_BOOT_VERSION_STRING, "\0"
-
- . = EXC_OFF_SYS_RESET
- .globl _start
-_start:
- lis r3, CONFIG_SYS_IMMR@h /* position IMMR */
- mtspr 638, r3
-
- /* Initialize machine status; enable machine check interrupt */
- /*----------------------------------------------------------------------*/
- li r3, MSR_KERNEL /* Set ME, RI flags */
- mtmsr r3
- mtspr SRR1, r3 /* Make SRR1 match MSR */
-
- mfspr r3, ICR /* clear Interrupt Cause Register */
-
- /* Initialize debug port registers */
- /*----------------------------------------------------------------------*/
- xor r0, r0, r0 /* Clear R0 */
- mtspr LCTRL1, r0 /* Initialize debug port regs */
- mtspr LCTRL2, r0
- mtspr COUNTA, r0
- mtspr COUNTB, r0
-
- /* Reset the caches */
- /*----------------------------------------------------------------------*/
-
- mfspr r3, IC_CST /* Clear error bits */
- mfspr r3, DC_CST
-
- lis r3, IDC_UNALL@h /* Unlock all */
- mtspr IC_CST, r3
- mtspr DC_CST, r3
-
- lis r3, IDC_INVALL@h /* Invalidate all */
- mtspr IC_CST, r3
- mtspr DC_CST, r3
-
- lis r3, IDC_DISABLE@h /* Disable data cache */
- mtspr DC_CST, r3
-
-#if !defined(CONFIG_SYS_DELAYED_ICACHE)
- /* On IP860 and PCU E,
- * we cannot enable IC yet
- */
- lis r3, IDC_ENABLE@h /* Enable instruction cache */
-#endif
- mtspr IC_CST, r3
-
- /* invalidate all tlb's */
- /*----------------------------------------------------------------------*/
-
- tlbia
- isync
-
- /*
- * Calculate absolute address in FLASH and jump there
- *----------------------------------------------------------------------*/
-
- lis r3, CONFIG_SYS_MONITOR_BASE@h
- ori r3, r3, CONFIG_SYS_MONITOR_BASE@l
- addi r3, r3, in_flash - _start + EXC_OFF_SYS_RESET
- mtlr r3
- blr
-
-in_flash:
-
- /* initialize some SPRs that are hard to access from C */
- /*----------------------------------------------------------------------*/
-
- lis r3, CONFIG_SYS_IMMR@h /* pass IMMR as arg1 to C routine */
- ori r1, r3, CONFIG_SYS_INIT_SP_OFFSET /* set up the stack in internal DPRAM */
- /* Note: R0 is still 0 here */
- stwu r0, -4(r1) /* clear final stack frame so that */
- stwu r0, -4(r1) /* stack backtraces terminate cleanly */
-
- /*
- * Disable serialized ifetch and show cycles
- * (i.e. set processor to normal mode).
- * This is also a silicon bug workaround, see errata
- */
-
- li r2, 0x0007
- mtspr ICTRL, r2
-
- /* Set up debug mode entry */
-
- lis r2, CONFIG_SYS_DER@h
- ori r2, r2, CONFIG_SYS_DER@l
- mtspr DER, r2
-
- /* let the C-code set up the rest */
- /* */
- /* Be careful to keep code relocatable ! */
- /*----------------------------------------------------------------------*/
-
- GET_GOT /* initialize GOT access */
-
- /* r3: IMMR */
- bl cpu_init_f /* run low-level CPU init code (from Flash) */
-
- bl board_init_f /* run 1st part of board init code (from Flash) */
-
- /* NOTREACHED - board_init_f() does not return */
-
-
- .globl _start_of_vectors
-_start_of_vectors:
-
-/* Machine check */
- STD_EXCEPTION(0x200, MachineCheck, MachineCheckException)
-
-/* Data Storage exception. "Never" generated on the 860. */
- STD_EXCEPTION(0x300, DataStorage, UnknownException)
-
-/* Instruction Storage exception. "Never" generated on the 860. */
- STD_EXCEPTION(0x400, InstStorage, UnknownException)
-
-/* External Interrupt exception. */
- STD_EXCEPTION(0x500, ExtInterrupt, external_interrupt)
-
-/* Alignment exception. */
- . = 0x600
-Alignment:
- EXCEPTION_PROLOG(SRR0, SRR1)
- mfspr r4,DAR
- stw r4,_DAR(r21)
- mfspr r5,DSISR
- stw r5,_DSISR(r21)
- addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_TEMPLATE(Alignment, AlignmentException, MSR_KERNEL, COPY_EE)
-
-/* Program check exception */
- . = 0x700
-ProgramCheck:
- EXCEPTION_PROLOG(SRR0, SRR1)
- addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_TEMPLATE(ProgramCheck, ProgramCheckException,
- MSR_KERNEL, COPY_EE)
-
- /* No FPU on MPC8xx. This exception is not supposed to happen.
- */
- STD_EXCEPTION(0x800, FPUnavailable, UnknownException)
-
- /* I guess we could implement decrementer, and may have
- * to someday for timekeeping.
- */
- STD_EXCEPTION(0x900, Decrementer, timer_interrupt)
- STD_EXCEPTION(0xa00, Trap_0a, UnknownException)
- STD_EXCEPTION(0xb00, Trap_0b, UnknownException)
- STD_EXCEPTION(0xc00, SystemCall, UnknownException)
- STD_EXCEPTION(0xd00, SingleStep, UnknownException)
-
- STD_EXCEPTION(0xe00, Trap_0e, UnknownException)
- STD_EXCEPTION(0xf00, Trap_0f, UnknownException)
-
- /* On the MPC8xx, this is a software emulation interrupt. It occurs
- * for all unimplemented and illegal instructions.
- */
- STD_EXCEPTION(0x1000, SoftEmu, SoftEmuException)
-
- STD_EXCEPTION(0x1100, InstructionTLBMiss, UnknownException)
- STD_EXCEPTION(0x1200, DataTLBMiss, UnknownException)
- STD_EXCEPTION(0x1300, InstructionTLBError, UnknownException)
- STD_EXCEPTION(0x1400, DataTLBError, UnknownException)
-
- STD_EXCEPTION(0x1500, Reserved5, UnknownException)
- STD_EXCEPTION(0x1600, Reserved6, UnknownException)
- STD_EXCEPTION(0x1700, Reserved7, UnknownException)
- STD_EXCEPTION(0x1800, Reserved8, UnknownException)
- STD_EXCEPTION(0x1900, Reserved9, UnknownException)
- STD_EXCEPTION(0x1a00, ReservedA, UnknownException)
- STD_EXCEPTION(0x1b00, ReservedB, UnknownException)
-
- STD_EXCEPTION(0x1c00, DataBreakpoint, UnknownException)
- STD_EXCEPTION(0x1d00, InstructionBreakpoint, DebugException)
- STD_EXCEPTION(0x1e00, PeripheralBreakpoint, UnknownException)
- STD_EXCEPTION(0x1f00, DevPortBreakpoint, UnknownException)
-
-
- .globl _end_of_vectors
-_end_of_vectors:
-
-
- . = 0x2000
-
-/*
- * This code finishes saving the registers to the exception frame
- * and jumps to the appropriate handler for the exception.
- * Register r21 is pointer into trap frame, r1 has new stack pointer.
- */
- .globl transfer_to_handler
-transfer_to_handler:
- stw r22,_NIP(r21)
- lis r22,MSR_POW@h
- andc r23,r23,r22
- stw r23,_MSR(r21)
- SAVE_GPR(7, r21)
- SAVE_4GPRS(8, r21)
- SAVE_8GPRS(12, r21)
- SAVE_8GPRS(24, r21)
- mflr r23
- andi. r24,r23,0x3f00 /* get vector offset */
- stw r24,TRAP(r21)
- li r22,0
- stw r22,RESULT(r21)
- mtspr SPRG2,r22 /* r1 is now kernel sp */
- lwz r24,0(r23) /* virtual address of handler */
- lwz r23,4(r23) /* where to go when done */
- mtspr SRR0,r24
- mtspr SRR1,r20
- mtlr r23
- SYNC
- rfi /* jump to handler, enable MMU */
-
-int_return:
- mfmsr r28 /* Disable interrupts */
- li r4,0
- ori r4,r4,MSR_EE
- andc r28,r28,r4
- SYNC /* Some chip revs need this... */
- mtmsr r28
- SYNC
- lwz r2,_CTR(r1)
- lwz r0,_LINK(r1)
- mtctr r2
- mtlr r0
- lwz r2,_XER(r1)
- lwz r0,_CCR(r1)
- mtspr XER,r2
- mtcrf 0xFF,r0
- REST_10GPRS(3, r1)
- REST_10GPRS(13, r1)
- REST_8GPRS(23, r1)
- REST_GPR(31, r1)
- lwz r2,_NIP(r1) /* Restore environment */
- lwz r0,_MSR(r1)
- mtspr SRR0,r2
- mtspr SRR1,r0
- lwz r0,GPR0(r1)
- lwz r2,GPR2(r1)
- lwz r1,GPR1(r1)
- SYNC
- rfi
-
-/* Cache functions.
-*/
- .globl icache_enable
-icache_enable:
- SYNC
- lis r3, IDC_INVALL@h
- mtspr IC_CST, r3
- lis r3, IDC_ENABLE@h
- mtspr IC_CST, r3
- blr
-
- .globl icache_disable
-icache_disable:
- SYNC
- lis r3, IDC_DISABLE@h
- mtspr IC_CST, r3
- blr
-
- .globl icache_status
-icache_status:
- mfspr r3, IC_CST
- srwi r3, r3, 31 /* >>31 => select bit 0 */
- blr
-
- .globl dcache_enable
-dcache_enable:
-#if 0
- SYNC
-#endif
-#if 1
- lis r3, 0x0400 /* Set cache mode with MMU off */
- mtspr MD_CTR, r3
-#endif
-
- lis r3, IDC_INVALL@h
- mtspr DC_CST, r3
-#if 0
- lis r3, DC_SFWT@h
- mtspr DC_CST, r3
-#endif
- lis r3, IDC_ENABLE@h
- mtspr DC_CST, r3
- blr
-
- .globl dcache_disable
-dcache_disable:
- SYNC
- lis r3, IDC_DISABLE@h
- mtspr DC_CST, r3
- lis r3, IDC_INVALL@h
- mtspr DC_CST, r3
- blr
-
- .globl dcache_status
-dcache_status:
- mfspr r3, DC_CST
- srwi r3, r3, 31 /* >>31 => select bit 0 */
- blr
-
- .globl dc_read
-dc_read:
- mtspr DC_ADR, r3
- mfspr r3, DC_DAT
- blr
-
-/*
- * unsigned int get_immr (unsigned int mask)
- *
- * return (mask ? (IMMR & mask) : IMMR);
- */
- .globl get_immr
-get_immr:
- mr r4,r3 /* save mask */
- mfspr r3, IMMR /* IMMR */
- cmpwi 0,r4,0 /* mask != 0 ? */
- beq 4f
- and r3,r3,r4 /* IMMR & mask */
-4:
- blr
-
- .globl get_pvr
-get_pvr:
- mfspr r3, PVR
- blr
-
-
- .globl wr_ic_cst
-wr_ic_cst:
- mtspr IC_CST, r3
- blr
-
- .globl rd_ic_cst
-rd_ic_cst:
- mfspr r3, IC_CST
- blr
-
- .globl wr_ic_adr
-wr_ic_adr:
- mtspr IC_ADR, r3
- blr
-
-
- .globl wr_dc_cst
-wr_dc_cst:
- mtspr DC_CST, r3
- blr
-
- .globl rd_dc_cst
-rd_dc_cst:
- mfspr r3, DC_CST
- blr
-
- .globl wr_dc_adr
-wr_dc_adr:
- mtspr DC_ADR, r3
- blr
-
-/*------------------------------------------------------------------------------*/
-
-/*
- * void relocate_code (addr_sp, gd, addr_moni)
- *
- * This "function" does not return, instead it continues in RAM
- * after relocating the monitor code.
- *
- * r3 = dest
- * r4 = src
- * r5 = length in bytes
- * r6 = cachelinesize
- */
- .globl relocate_code
-relocate_code:
- mr r1, r3 /* Set new stack pointer */
- mr r9, r4 /* Save copy of Global Data pointer */
- mr r10, r5 /* Save copy of Destination Address */
-
- GET_GOT
- mr r3, r5 /* Destination Address */
- lis r4, CONFIG_SYS_MONITOR_BASE@h /* Source Address */
- ori r4, r4, CONFIG_SYS_MONITOR_BASE@l
- lwz r5, GOT(__init_end)
- sub r5, r5, r4
- li r6, CONFIG_SYS_CACHELINE_SIZE /* Cache Line Size */
-
- /*
- * Fix GOT pointer:
- *
- * New GOT-PTR = (old GOT-PTR - CONFIG_SYS_MONITOR_BASE) + Destination Address
- *
- * Offset:
- */
- sub r15, r10, r4
-
- /* First our own GOT */
- add r12, r12, r15
- /* then the one used by the C code */
- add r30, r30, r15
-
- /*
- * Now relocate code
- */
-
- cmplw cr1,r3,r4
- addi r0,r5,3
- srwi. r0,r0,2
- beq cr1,4f /* In place copy is not necessary */
- beq 7f /* Protect against 0 count */
- mtctr r0
- bge cr1,2f
-
- la r8,-4(r4)
- la r7,-4(r3)
-1: lwzu r0,4(r8)
- stwu r0,4(r7)
- bdnz 1b
- b 4f
-
-2: slwi r0,r0,2
- add r8,r4,r0
- add r7,r3,r0
-3: lwzu r0,-4(r8)
- stwu r0,-4(r7)
- bdnz 3b
-
-/*
- * Now flush the cache: note that we must start from a cache aligned
- * address. Otherwise we might miss one cache line.
- */
-4: cmpwi r6,0
- add r5,r3,r5
- beq 7f /* Always flush prefetch queue in any case */
- subi r0,r6,1
- andc r3,r3,r0
- mr r4,r3
-5: dcbst 0,r4
- add r4,r4,r6
- cmplw r4,r5
- blt 5b
- sync /* Wait for all dcbst to complete on bus */
- mr r4,r3
-6: icbi 0,r4
- add r4,r4,r6
- cmplw r4,r5
- blt 6b
-7: sync /* Wait for all icbi to complete on bus */
- isync
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-
- addi r0, r10, in_ram - _start + EXC_OFF_SYS_RESET
- mtlr r0
- blr
-
-in_ram:
-
- /*
- * Relocation Function, r12 point to got2+0x8000
- *
- * Adjust got2 pointers, no need to check for 0, this code
- * already puts a few entries in the table.
- */
- li r0,__got2_entries@sectoff@l
- la r3,GOT(_GOT2_TABLE_)
- lwz r11,GOT(_GOT2_TABLE_)
- mtctr r0
- sub r11,r3,r11
- addi r3,r3,-4
-1: lwzu r0,4(r3)
- cmpwi r0,0
- beq- 2f
- add r0,r0,r11
- stw r0,0(r3)
-2: bdnz 1b
-
- /*
- * Now adjust the fixups and the pointers to the fixups
- * in case we need to move ourselves again.
- */
- li r0,__fixup_entries@sectoff@l
- lwz r3,GOT(_FIXUP_TABLE_)
- cmpwi r0,0
- mtctr r0
- addi r3,r3,-4
- beq 4f
-3: lwzu r4,4(r3)
- lwzux r0,r4,r11
- cmpwi r0,0
- add r0,r0,r11
- stw r4,0(r3)
- beq- 5f
- stw r0,0(r4)
-5: bdnz 3b
-4:
-clear_bss:
- /*
- * Now clear BSS segment
- */
- lwz r3,GOT(__bss_start)
- lwz r4,GOT(__bss_end)
-
- cmplw 0, r3, r4
- beq 6f
-
- li r0, 0
-5:
- stw r0, 0(r3)
- addi r3, r3, 4
- cmplw 0, r3, r4
- bne 5b
-6:
-
- mr r3, r9 /* Global Data pointer */
- mr r4, r10 /* Destination Address */
- bl board_init_r
-
- /*
- * Copy exception vector code to low memory
- *
- * r3: dest_addr
- * r7: source address, r8: end address, r9: target address
- */
- .globl trap_init
-trap_init:
- mflr r4 /* save link register */
- GET_GOT
- lwz r7, GOT(_start)
- lwz r8, GOT(_end_of_vectors)
-
- li r9, 0x100 /* reset vector always at 0x100 */
-
- cmplw 0, r7, r8
- bgelr /* return if r7>=r8 - just in case */
-1:
- lwz r0, 0(r7)
- stw r0, 0(r9)
- addi r7, r7, 4
- addi r9, r9, 4
- cmplw 0, r7, r8
- bne 1b
-
- /*
- * relocate `hdlr' and `int_return' entries
- */
- li r7, .L_MachineCheck - _start + EXC_OFF_SYS_RESET
- li r8, Alignment - _start + EXC_OFF_SYS_RESET
-2:
- bl trap_reloc
- addi r7, r7, 0x100 /* next exception vector */
- cmplw 0, r7, r8
- blt 2b
-
- li r7, .L_Alignment - _start + EXC_OFF_SYS_RESET
- bl trap_reloc
-
- li r7, .L_ProgramCheck - _start + EXC_OFF_SYS_RESET
- bl trap_reloc
-
- li r7, .L_FPUnavailable - _start + EXC_OFF_SYS_RESET
- li r8, SystemCall - _start + EXC_OFF_SYS_RESET
-3:
- bl trap_reloc
- addi r7, r7, 0x100 /* next exception vector */
- cmplw 0, r7, r8
- blt 3b
-
- li r7, .L_SingleStep - _start + EXC_OFF_SYS_RESET
- li r8, _end_of_vectors - _start + EXC_OFF_SYS_RESET
-4:
- bl trap_reloc
- addi r7, r7, 0x100 /* next exception vector */
- cmplw 0, r7, r8
- blt 4b
-
- mtlr r4 /* restore link register */
- blr
diff --git a/arch/powerpc/cpu/mpc8xx/traps.c b/arch/powerpc/cpu/mpc8xx/traps.c
deleted file mode 100644
index 01f24ac1a96a799aa7623e10618ba0d20f7e35f7..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/traps.c
+++ /dev/null
@@ -1,216 +0,0 @@
-/*
- * linux/arch/powerpc/kernel/traps.c
- *
- * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org)
- *
- * Modified by Cort Dougan (cort@cs.nmt.edu)
- * and Paul Mackerras (paulus@cs.anu.edu.au)
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * This file handles the architecture-dependent parts of hardware exceptions
- */
-
-#include <common.h>
-#include <command.h>
-#include <kgdb.h>
-#include <asm/processor.h>
-
-#if defined(CONFIG_CMD_BEDBUG)
-extern void do_bedbug_breakpoint(struct pt_regs *);
-#endif
-
-/* Returns 0 if exception not found and fixup otherwise. */
-extern unsigned long search_exception_table(unsigned long);
-
-/* THIS NEEDS CHANGING to use the board info structure.
-*/
-#define END_OF_MEM 0x02000000
-
-/*
- * Trap & Exception support
- */
-
-static void print_backtrace(unsigned long *sp)
-{
- int cnt = 0;
- unsigned long i;
-
- printf("Call backtrace: ");
- while (sp) {
- if ((uint)sp > END_OF_MEM)
- break;
-
- i = sp[1];
- if (cnt++ % 7 == 0)
- printf("\n");
- printf("%08lX ", i);
- if (cnt > 32) break;
- sp = (unsigned long *)*sp;
- }
- printf("\n");
-}
-
-void show_regs(struct pt_regs *regs)
-{
- int i;
-
- printf("NIP: %08lX XER: %08lX LR: %08lX REGS: %p TRAP: %04lx DAR: %08lX\n",
- regs->nip, regs->xer, regs->link, regs, regs->trap, regs->dar);
- printf("MSR: %08lx EE: %01x PR: %01x FP: %01x ME: %01x IR/DR: %01x%01x\n",
- regs->msr, regs->msr&MSR_EE ? 1 : 0, regs->msr&MSR_PR ? 1 : 0,
- regs->msr & MSR_FP ? 1 : 0,regs->msr&MSR_ME ? 1 : 0,
- regs->msr&MSR_IR ? 1 : 0,
- regs->msr&MSR_DR ? 1 : 0);
-
- printf("\n");
- for (i = 0; i < 32; i++) {
- if ((i % 8) == 0)
- {
- printf("GPR%02d: ", i);
- }
-
- printf("%08lX ", regs->gpr[i]);
- if ((i % 8) == 7)
- {
- printf("\n");
- }
- }
-}
-
-
-static void _exception(int signr, struct pt_regs *regs)
-{
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Exception in kernel pc %lx signal %d",regs->nip,signr);
-}
-
-void MachineCheckException(struct pt_regs *regs)
-{
- unsigned long fixup;
-
- /* Probing PCI using config cycles cause this exception
- * when a device is not present. Catch it and return to
- * the PCI exception handler.
- */
- if ((fixup = search_exception_table(regs->nip)) != 0) {
- regs->nip = fixup;
- return;
- }
-
-#if defined(CONFIG_CMD_KGDB)
- if (debugger_exception_handler && (*debugger_exception_handler)(regs))
- return;
-#endif
-
- printf("Machine check in kernel mode.\n");
- printf("Caused by (from msr): ");
- printf("regs %p ",regs);
- switch( regs->msr & 0x000F0000) {
- case (0x80000000>>12):
- printf("Machine check signal - probably due to mm fault\n"
- "with mmu off\n");
- break;
- case (0x80000000>>13):
- printf("Transfer error ack signal\n");
- break;
- case (0x80000000>>14):
- printf("Data parity signal\n");
- break;
- case (0x80000000>>15):
- printf("Address parity signal\n");
- break;
- default:
- printf("Unknown values in msr\n");
- }
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("machine check");
-}
-
-void AlignmentException(struct pt_regs *regs)
-{
-#if defined(CONFIG_CMD_KGDB)
- if (debugger_exception_handler && (*debugger_exception_handler)(regs))
- return;
-#endif
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Alignment Exception");
-}
-
-void ProgramCheckException(struct pt_regs *regs)
-{
-#if defined(CONFIG_CMD_KGDB)
- if (debugger_exception_handler && (*debugger_exception_handler)(regs))
- return;
-#endif
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Program Check Exception");
-}
-
-void SoftEmuException(struct pt_regs *regs)
-{
-#if defined(CONFIG_CMD_KGDB)
- if (debugger_exception_handler && (*debugger_exception_handler)(regs))
- return;
-#endif
- show_regs(regs);
- print_backtrace((unsigned long *)regs->gpr[1]);
- panic("Software Emulation Exception");
-}
-
-
-void UnknownException(struct pt_regs *regs)
-{
-#if defined(CONFIG_CMD_KGDB)
- if (debugger_exception_handler && (*debugger_exception_handler)(regs))
- return;
-#endif
- printf("Bad trap at PC: %lx, SR: %lx, vector=%lx\n",
- regs->nip, regs->msr, regs->trap);
- _exception(0, regs);
-}
-
-void DebugException(struct pt_regs *regs)
-{
- printf("Debugger trap at @ %lx\n", regs->nip );
- show_regs(regs);
-#if defined(CONFIG_CMD_BEDBUG)
- do_bedbug_breakpoint( regs );
-#endif
-}
-
-/* Probe an address by reading. If not present, return -1, otherwise
- * return 0.
- */
-int addr_probe(uint *addr)
-{
-#if 0
- int retval;
-
- __asm__ __volatile__( \
- "1: lwz %0,0(%1)\n" \
- " eieio\n" \
- " li %0,0\n" \
- "2:\n" \
- ".section .fixup,\"ax\"\n" \
- "3: li %0,-1\n" \
- " b 2b\n" \
- ".section __ex_table,\"a\"\n" \
- " .align 2\n" \
- " .long 1b,3b\n" \
- ".text" \
- : "=r" (retval) : "r"(addr));
-
- return (retval);
-#endif
- return 0;
-}
diff --git a/arch/powerpc/cpu/mpc8xx/upatch.c b/arch/powerpc/cpu/mpc8xx/upatch.c
deleted file mode 100644
index a8cb735ab7717e7e5ea3821059f11bbc0eacda5c..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/upatch.c
+++ /dev/null
@@ -1,194 +0,0 @@
-#include <common.h>
-#include <commproc.h>
-
-#if defined(CONFIG_SYS_I2C_UCODE_PATCH) || defined(CONFIG_SYS_SPI_UCODE_PATCH) || \
- defined(CONFIG_SYS_SMC_UCODE_PATCH)
-
-static void UcodeCopy (volatile cpm8xx_t *cpm);
-
-void cpm_load_patch (volatile immap_t *immr)
-{
- immr->im_cpm.cp_rccr &= ~0x0003; /* Disable microcode program area */
-
- UcodeCopy ((cpm8xx_t *)&immr->im_cpm); /* Copy ucode patch to DPRAM */
-#ifdef CONFIG_SYS_SPI_UCODE_PATCH
- {
- volatile spi_t *spi = (spi_t *) & immr->im_cpm.cp_dparam[PROFF_SPI];
- /* Activate the microcode per the instructions in the microcode manual */
- /* NOTE: We're only relocating the SPI parameters (not I2C). */
- immr->im_cpm.cp_cpmcr1 = 0x802a; /* Write Trap register 1 value */
- immr->im_cpm.cp_cpmcr2 = 0x8028; /* Write Trap register 2 value */
- spi->spi_rpbase = CONFIG_SYS_SPI_DPMEM_OFFSET; /* Where to relocte SPI params */
- }
-#endif
-
-#ifdef CONFIG_SYS_I2C_UCODE_PATCH
- {
- volatile iic_t *iip = (iic_t *) & immr->im_cpm.cp_dparam[PROFF_IIC];
- /* Activate the microcode per the instructions in the microcode manual */
- /* NOTE: We're only relocating the I2C parameters (not SPI). */
- immr->im_cpm.cp_cpmcr3 = 0x802e; /* Write Trap register 3 value */
- immr->im_cpm.cp_cpmcr4 = 0x802c; /* Write Trap register 4 value */
- iip->iic_rpbase = CONFIG_SYS_I2C_DPMEM_OFFSET; /* Where to relocte I2C params */
- }
-#endif
-
-#ifdef CONFIG_SYS_SMC_UCODE_PATCH
- {
- volatile smc_uart_t *up = (smc_uart_t *) & immr->im_cpm.cp_dparam[PROFF_SMC1];
- /* Activate the microcode per the instructions in the microcode manual */
- /* NOTE: We're only relocating the SMC parameters. */
- immr->im_cpm.cp_cpmcr1 = 0x8080; /* Write Trap register 1 value */
- immr->im_cpm.cp_cpmcr2 = 0x8088; /* Write Trap register 2 value */
- up->smc_rpbase = CONFIG_SYS_SMC_DPMEM_OFFSET; /* Where to relocte SMC params */
- }
-#endif
-
- /*
- * Enable DPRAM microcode to execute from the first 512 bytes
- * and a 256 byte extension of DPRAM.
- */
-#ifdef CONFIG_SYS_SMC_UCODE_PATCH
- immr->im_cpm.cp_rccr |= 0x0002;
-#else
- immr->im_cpm.cp_rccr |= 0x0001;
-#endif
-}
-
-#if defined(CONFIG_SYS_I2C_UCODE_PATCH) || defined(CONFIG_SYS_SPI_UCODE_PATCh)
-static ulong patch_2000[] = {
- 0x7FFFEFD9, 0x3FFD0000, 0x7FFB49F7, 0x7FF90000,
- 0x5FEFADF7, 0x5F88ADF7, 0x5FEFAFF7, 0x5F88AFF7,
- 0x3A9CFBC8, 0x77CAE1BB, 0xF4DE7FAD, 0xABAE9330,
- 0x4E08FDCF, 0x6E0FAFF8, 0x7CCF76CF, 0xFDAFF9CF,
- 0xABF88DC8, 0xAB5879F7, 0xB0927383, 0xDFD079F7,
- 0xB090E6BB, 0xE5BBE74F, 0xB3FA6F0F, 0x6FFB76CE,
- 0xEE0CF9CF, 0x2BFBEFEF, 0xCFEEF9CF, 0x76CEAD23,
- 0x90B3DF99, 0x7FDDD0C1, 0x4BF847FD, 0x7CCF76CE,
- 0xCFEF77CA, 0x7EAF7FAD, 0x7DFDF0B7, 0xEF7A7FCA,
- 0x77CAFBC8, 0x6079E722, 0xFBC85FFF, 0xDFFF5FB3,
- 0xFFFBFBC8, 0xF3C894A5, 0xE7C9EDF9, 0x7F9A7FAD,
- 0x5F36AFE8, 0x5F5BFFDF, 0xDF95CB9E, 0xAF7D5FC3,
- 0xAFED8C1B, 0x5FC3AFDD, 0x5FC5DF99, 0x7EFDB0B3,
- 0x5FB3FFFE, 0xABAE5FB3, 0xFFFE5FD0, 0x600BE6BB,
- 0x600B5FD0, 0xDFC827FB, 0xEFDF5FCA, 0xCFDE3A9C,
- 0xE7C9EDF9, 0xF3C87F9E, 0x54CA7FED, 0x2D3A3637,
- 0x756F7E9A, 0xF1CE37EF, 0x2E677FEE, 0x10EBADF8,
- 0xEFDECFEA, 0xE52F7D9F, 0xE12BF1CE, 0x5F647E9A,
- 0x4DF8CFEA, 0x5F717D9B, 0xEFEECFEA, 0x5F73E522,
- 0xEFDE5F73, 0xCFDA0B61, 0x7385DF61, 0xE7C9EDF9,
- 0x7E9A30D5, 0x1458BFFF, 0xF3C85FFF, 0xDFFFA7F8,
- 0x5F5BBFFE, 0x7F7D10D0, 0x144D5F33, 0xBFFFAF78,
- 0x5F5BBFFD, 0xA7F85F33, 0xBFFE77FD, 0x30BD4E08,
- 0xFDCFE5FF, 0x6E0FAFF8, 0x7EEF7E9F, 0xFDEFF1CF,
- 0x5F17ABF8, 0x0D5B5F5B, 0xFFEF79F7, 0x309EAFDD,
- 0x5F3147F8, 0x5F31AFED, 0x7FDD50AF, 0x497847FD,
- 0x7F9E7FED, 0x7DFD70A9, 0xEF7E7ECE, 0x6BA07F9E,
- 0x2D227EFD, 0x30DB5F5B, 0xFFFD5F5B, 0xFFEF5F5B,
- 0xFFDF0C9C, 0xAFED0A9A, 0xAFDD0C37, 0x5F37AFBD,
- 0x7FBDB081, 0x5F8147F8,
-};
-
-static ulong patch_2F00[] = {
- 0x3E303430, 0x34343737, 0xABBF9B99, 0x4B4FBDBD,
- 0x59949334, 0x9FFF37FB, 0x9B177DD9, 0x936956BB,
- 0xFBDD697B, 0xDD2FD113, 0x1DB9F7BB, 0x36313963,
- 0x79373369, 0x3193137F, 0x7331737A, 0xF7BB9B99,
- 0x9BB19795, 0x77FDFD3D, 0x573B773F, 0x737933F7,
- 0xB991D115, 0x31699315, 0x31531694, 0xBF4FBDBD,
- 0x35931497, 0x35376956, 0xBD697B9D, 0x96931313,
- 0x19797937, 0x69350000,
-};
-#else
-
-static ulong patch_2000[] = {
- 0x3fff0000, 0x3ffd0000, 0x3ffb0000, 0x3ff90000,
- 0x5fefeff8, 0x5f91eff8, 0x3ff30000, 0x3ff10000,
- 0x3a11e710, 0xedf0ccb9, 0xf318ed66, 0x7f0e5fe2,
- 0x7fedbb38, 0x3afe7468, 0x7fedf4d8, 0x8ffbb92d,
- 0xb83b77fd, 0xb0bb5eb9, 0xdfda7fed, 0x90bde74d,
- 0x6f0dcbd3, 0xe7decfed, 0xcb50cfed, 0xcfeddf6d,
- 0x914d4f74, 0x5eaedfcb, 0x9ee0e7df, 0xefbb6ffb,
- 0xe7ef7f0e, 0x9ee57fed, 0xebb7effa, 0xeb30affb,
- 0x7fea90b3, 0x7e0cf09f, 0xbffff318, 0x5fffdfff,
- 0xac35efea, 0x7fce1fc1, 0xe2ff5fbd, 0xaffbe2ff,
- 0x5fbfaffb, 0xf9a87d0f, 0xaef8770f, 0x7d0fb0a2,
- 0xeffbbfff, 0xcfef5fba, 0x7d0fbfff, 0x5fba4cf8,
- 0x7fddd09b, 0x49f847fd, 0x7efdf097, 0x7fedfffd,
- 0x7dfdf093, 0xef7e7e1e, 0x5fba7f0e, 0x3a11e710,
- 0xedf0cc87, 0xfb18ad0a, 0x1f85bbb8, 0x74283b7e,
- 0x7375e4bb, 0x2ab64fb8, 0x5c7de4bb, 0x32fdffbf,
- 0x5f0843f8, 0x7ce3e1bb, 0xe74f7ded, 0x6f0f4fe8,
- 0xc7ba32be, 0x73f2efeb, 0x600b4f78, 0xe5bb760b,
- 0x5388aef8, 0x4ef80b6a, 0xcfef9ee5, 0xabf8751f,
- 0xefef5b88, 0x741f4fe8, 0x751e760d, 0x7fdb70dd,
- 0x741cafce, 0xefcc7fce, 0x751e7088, 0x741ce7bb,
- 0x334ecfed, 0xafdbefeb, 0xe5bb760b, 0x53ceaef8,
- 0xafe8e7eb, 0x4bf8771e, 0x7e007fed, 0x4fcbe2cc,
- 0x7fbc3085, 0x7b0f7a0f, 0x34b177fd, 0xb0e75e93,
- 0xdf313e3b, 0xaf78741f, 0x741f30cc, 0xcfef5f08,
- 0x741f3e88, 0xafb8771e, 0x5f437fed, 0x0bafe2cc,
- 0x741ccfec, 0xe5ca53a9, 0x6fcb4f74, 0x5e89df27,
- 0x2a923d14, 0x4b8fdf0c, 0x751f741c, 0x6c1eeffa,
- 0xefea7fce, 0x6ffc309a, 0xefec3fca, 0x308fdf0a,
- 0xadf85e7a, 0xaf7daefd, 0x5e7adf0a, 0x5e7aafdd,
- 0x761f1088, 0x1e7c7efd, 0x3089fffe, 0x4908fb18,
- 0x5fffdfff, 0xafbbf0f7, 0x4ef85f43, 0xadf81489,
- 0x7a0f7089, 0xcfef5089, 0x7a0fdf0c, 0x5e7cafed,
- 0xbc6e780f, 0xefef780f, 0xefef790f, 0xa7f85eeb,
- 0xffef790f, 0xefef790f, 0x1489df0a, 0x5e7aadfd,
- 0x5f09fffb, 0xe79aded9, 0xeff96079, 0x607ae79a,
- 0xded8eff9, 0x60795edb, 0x607acfef, 0xefefefdf,
- 0xefbfef7f, 0xeeffedff, 0xebffe7ff, 0xafefafdf,
- 0xafbfaf7f, 0xaeffadff, 0xabffa7ff, 0x6fef6fdf,
- 0x6fbf6f7f, 0x6eff6dff, 0x6bff67ff, 0x2fef2fdf,
- 0x2fbf2f7f, 0x2eff2dff, 0x2bff27ff, 0x4e08fd1f,
- 0xe5ff6e0f, 0xaff87eef, 0x7e0ffdef, 0xf11f6079,
- 0xabf8f51e, 0x7e0af11c, 0x37cfae16, 0x7fec909a,
- 0xadf8efdc, 0xcfeae52f, 0x7d0fe12b, 0xf11c6079,
- 0x7e0a4df8, 0xcfea5ea0, 0x7d0befec, 0xcfea5ea2,
- 0xe522efdc, 0x5ea2cfda, 0x4e08fd1f, 0x6e0faff8,
- 0x7c1f761f, 0xfdeff91f, 0x6079abf8, 0x761cee00,
- 0xf91f2bfb, 0xefefcfec, 0xf91f6079, 0x761c27fb,
- 0xefdf5e83, 0xcfdc7fdd, 0x50f84bf8, 0x47fd7c1f,
- 0x761ccfcf, 0x7eef7fed, 0x7dfd70ef, 0xef7e7f1e,
- 0x771efb18, 0x6079e722, 0xe6bbe5bb, 0x2e66e5bb,
- 0x600b2ee1, 0xe2bbe2bb, 0xe2bbe2bb, 0x2f5ee2bb,
- 0xe2bb2ff9, 0x6079e2bb,
-};
-
-static ulong patch_2F00[] = {
- 0x30303030, 0x3e3e3030, 0xaf79b9b3, 0xbaa3b979,
- 0x9693369f, 0x79f79777, 0x97333fff, 0xfb3b9e9f,
- 0x79b91d11, 0x9e13f3ff, 0x3f9b6bd9, 0xe173d136,
- 0x695669d1, 0x697b3daf, 0x79b93a3a, 0x3f979f91,
- 0x379ff976, 0xf99777fd, 0x9779737d, 0xe9d6bbf9,
- 0xbfffd9df, 0x97f7fd97, 0x6f7b9bff, 0xf9bd9683,
- 0x397db973, 0xd97b3b9f, 0xd7f9f733, 0x9993bb9e,
- 0xe1f9ef93, 0x73773337, 0xb936917d, 0x11f87379,
- 0xb979d336, 0x8b7ded73, 0x1b7d9337, 0x31f3f22f,
- 0x3f2327ee, 0xeeeeeeee, 0xeeeeeeee, 0xeeeeeeee,
- 0xeeeeee4b, 0xf4fbdbd2, 0x58bb1878, 0x577fdfd2,
- 0xd573b773, 0xf7374b4f, 0xbdbd25b8, 0xb177d2d1,
- 0x7376856b, 0xbfdd687b, 0xdd2fff8f, 0x78ffff8f,
- 0xf22f0000,
-};
-#endif
-
-static void UcodeCopy (volatile cpm8xx_t *cpm)
-{
- vu_long *p;
- int i;
-
- p = (vu_long *)&(cpm->cp_dpmem[0x0000]);
- for (i=0; i < sizeof(patch_2000)/4; ++i) {
- p[i] = patch_2000[i];
- }
-
- p = (vu_long *)&(cpm->cp_dpmem[0x0F00]);
- for (i=0; i < sizeof(patch_2F00)/4; ++i) {
- p[i] = patch_2F00[i];
- }
-}
-
-#endif /* CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_SPI_UCODE_PATCH */
diff --git a/arch/powerpc/cpu/mpc8xx/video.c b/arch/powerpc/cpu/mpc8xx/video.c
deleted file mode 100644
index c35406d37b53df73198e8e5744a1acdfb13614b5..0000000000000000000000000000000000000000
--- a/arch/powerpc/cpu/mpc8xx/video.c
+++ /dev/null
@@ -1,1123 +0,0 @@
-/*
- * (C) Copyright 2000
- * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it
- * (C) Copyright 2002
- * Wolfgang Denk, wd@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* #define DEBUG */
-
-/************************************************************************/
-/* ** HEADER FILES */
-/************************************************************************/
-
-#include <stdarg.h>
-#include <common.h>
-#include <config.h>
-#include <version.h>
-#include <i2c.h>
-#include <linux/types.h>
-#include <stdio_dev.h>
-
-#ifdef CONFIG_VIDEO
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/************************************************************************/
-/* ** DEBUG SETTINGS */
-/************************************************************************/
-
-#if 0
-#define VIDEO_DEBUG_COLORBARS /* Force colorbars output */
-#endif
-
-/************************************************************************/
-/* ** VIDEO MODE SETTINGS */
-/************************************************************************/
-
-#if 0
-#define VIDEO_MODE_EXTENDED /* Allow screen size bigger than visible area */
-#define VIDEO_MODE_NTSC
-#endif
-
-#define VIDEO_MODE_PAL
-
-#if 0
-#define VIDEO_BLINK /* This enables cursor blinking (under construction) */
-#endif
-
-#define VIDEO_INFO /* Show U-Boot information */
-#define VIDEO_INFO_X VIDEO_LOGO_WIDTH+8
-#define VIDEO_INFO_Y 16
-
-/************************************************************************/
-/* ** VIDEO MODE CONSTANTS */
-/************************************************************************/
-
-#ifdef VIDEO_MODE_EXTENDED
-#define VIDEO_COLS VIDEO_ACTIVE_COLS
-#define VIDEO_ROWS VIDEO_ACTIVE_ROWS
-#else
-#define VIDEO_COLS VIDEO_VISIBLE_COLS
-#define VIDEO_ROWS VIDEO_VISIBLE_ROWS
-#endif
-
-#define VIDEO_PIXEL_SIZE (VIDEO_MODE_BPP/8)
-#define VIDEO_SIZE (VIDEO_ROWS*VIDEO_COLS*VIDEO_PIXEL_SIZE) /* Total size of buffer */
-#define VIDEO_PIX_BLOCKS (VIDEO_SIZE >> 2) /* Number of ints */
-#define VIDEO_LINE_LEN (VIDEO_COLS*VIDEO_PIXEL_SIZE) /* Number of bytes per line */
-#define VIDEO_BURST_LEN (VIDEO_COLS/8)
-
-#ifdef VIDEO_MODE_YUYV
-#define VIDEO_BG_COL 0x80D880D8 /* Background color in YUYV format */
-#else
-#define VIDEO_BG_COL 0xF8F8F8F8 /* Background color in RGB format */
-#endif
-
-/************************************************************************/
-/* ** FONT AND LOGO DATA */
-/************************************************************************/
-
-#include <video_font.h> /* Get font data, width and height */
-
-#ifdef CONFIG_VIDEO_LOGO
-#include <video_logo.h> /* Get logo data, width and height */
-
-#define VIDEO_LOGO_WIDTH DEF_U_BOOT_LOGO_WIDTH
-#define VIDEO_LOGO_HEIGHT DEF_U_BOOT_LOGO_HEIGHT
-#define VIDEO_LOGO_ADDR &u_boot_logo
-#endif
-
-/************************************************************************/
-/* ** VIDEO CONTROLLER CONSTANTS */
-/************************************************************************/
-
-/* VCCR - VIDEO CONTROLLER CONFIGURATION REGISTER */
-
-#define VIDEO_VCCR_VON 0 /* Video controller ON */
-#define VIDEO_VCCR_CSRC 1 /* Clock source */
-#define VIDEO_VCCR_PDF 13 /* Pixel display format */
-#define VIDEO_VCCR_IEN 11 /* Interrupt enable */
-
-/* VSR - VIDEO STATUS REGISTER */
-
-#define VIDEO_VSR_CAS 6 /* Active set */
-#define VIDEO_VSR_EOF 0 /* End of frame */
-
-/* VCMR - VIDEO COMMAND REGISTER */
-
-#define VIDEO_VCMR_BD 0 /* Blank display */
-#define VIDEO_VCMR_ASEL 1 /* Active set selection */
-
-/* VBCB - VIDEO BACKGROUND COLOR BUFFER REGISTER */
-
-#define VIDEO_BCSR4_RESET_BIT 21 /* BCSR4 - Extern video encoder reset */
-#define VIDEO_BCSR4_EXTCLK_BIT 22 /* BCSR4 - Extern clock enable */
-#define VIDEO_BCSR4_VIDLED_BIT 23 /* BCSR4 - Video led disable */
-
-/************************************************************************/
-/* ** CONSOLE CONSTANTS */
-/************************************************************************/
-
-#ifdef CONFIG_VIDEO_LOGO
-#define CONSOLE_ROWS ((VIDEO_ROWS - VIDEO_LOGO_HEIGHT) / VIDEO_FONT_HEIGHT)
-#define VIDEO_LOGO_SKIP (VIDEO_COLS - VIDEO_LOGO_WIDTH)
-#else
-#define CONSOLE_ROWS (VIDEO_ROWS / VIDEO_FONT_HEIGHT)
-#endif
-
-#define CONSOLE_COLS (VIDEO_COLS / VIDEO_FONT_WIDTH)
-#define CONSOLE_ROW_SIZE (VIDEO_FONT_HEIGHT * VIDEO_LINE_LEN)
-#define CONSOLE_ROW_FIRST (video_console_address)
-#define CONSOLE_ROW_SECOND (video_console_address + CONSOLE_ROW_SIZE)
-#define CONSOLE_ROW_LAST (video_console_address + CONSOLE_SIZE - CONSOLE_ROW_SIZE)
-#define CONSOLE_SIZE (CONSOLE_ROW_SIZE * CONSOLE_ROWS)
-#define CONSOLE_SCROLL_SIZE (CONSOLE_SIZE - CONSOLE_ROW_SIZE)
-
-/*
- * Simple color definitions
- */
-#define CONSOLE_COLOR_BLACK 0
-#define CONSOLE_COLOR_RED 1
-#define CONSOLE_COLOR_GREEN 2
-#define CONSOLE_COLOR_YELLOW 3
-#define CONSOLE_COLOR_BLUE 4
-#define CONSOLE_COLOR_MAGENTA 5
-#define CONSOLE_COLOR_CYAN 6
-#define CONSOLE_COLOR_GREY 13
-#define CONSOLE_COLOR_GREY2 14
-#define CONSOLE_COLOR_WHITE 15 /* Must remain last / highest */
-
-/************************************************************************/
-/* ** BITOPS MACROS */
-/************************************************************************/
-
-#define HISHORT(i) ((i >> 16)&0xffff)
-#define LOSHORT(i) (i & 0xffff)
-#define HICHAR(s) ((i >> 8)&0xff)
-#define LOCHAR(s) (i & 0xff)
-#define HI(c) ((c >> 4)&0xf)
-#define LO(c) (c & 0xf)
-#define SWAPINT(i) (HISHORT(i) | (LOSHORT(i) << 16))
-#define SWAPSHORT(s) (HICHAR(s) | (LOCHAR(s) << 8))
-#define SWAPCHAR(c) (HI(c) | (LO(c) << 4))
-#define BITMASK(b) (1 << (b))
-#define GETBIT(v,b) (((v) & BITMASK(b)) > 0)
-#define SETBIT(v,b,d) (v = (((d)>0) ? (v) | BITMASK(b): (v) & ~BITMASK(b)))
-
-/************************************************************************/
-/* ** STRUCTURES */
-/************************************************************************/
-
-typedef struct {
- unsigned char V, Y1, U, Y2;
-} tYUYV;
-
-/* This structure is based on the Video Ram in the MPC823. */
-typedef struct VRAM {
- unsigned hx:2, /* Horizontal sync */
- vx:2, /* Vertical sync */
- fx:2, /* Frame */
- bx:2, /* Blank */
- res1:6, /* Reserved */
- vds:2, /* Video Data Select */
- inter:1, /* Interrupt */
- res2:2, /* Reserved */
- lcyc:11, /* Loop/video cycles */
- lp:1, /* Loop start/end */
- lst:1; /* Last entry */
-} VRAM;
-
-/************************************************************************/
-/* ** VARIABLES */
-/************************************************************************/
-
-static int
- video_panning_range_x = 0, /* Video mode invisible pixels x range */
- video_panning_range_y = 0, /* Video mode invisible pixels y range */
- video_panning_value_x = 0, /* Video mode x panning value (absolute) */
- video_panning_value_y = 0, /* Video mode y panning value (absolute) */
- video_panning_factor_x = 0, /* Video mode x panning value (-127 +127) */
- video_panning_factor_y = 0, /* Video mode y panning value (-127 +127) */
- console_col = 0, /* Cursor col */
- console_row = 0, /* Cursor row */
- video_palette[16]; /* Our palette */
-
-static const int video_font_draw_table[] =
- { 0x00000000, 0x0000ffff, 0xffff0000, 0xffffffff };
-
-static char
- video_color_fg = 0, /* Current fg color index (0-15) */
- video_color_bg = 0, /* Current bg color index (0-15) */
- video_enable = 0; /* Video has been initialized? */
-
-static void
- *video_fb_address, /* Frame buffer address */
- *video_console_address; /* Console frame buffer start address */
-
-/************************************************************************/
-/* ** MEMORY FUNCTIONS (32bit) */
-/************************************************************************/
-
-static void memsetl (int *p, int c, int v)
-{
- while (c--)
- *(p++) = v;
-}
-
-static void memcpyl (int *d, int *s, int c)
-{
- while (c--)
- *(d++) = *(s++);
-}
-
-/************************************************************************/
-/* ** VIDEO DRAWING AND COLOR FUNCTIONS */
-/************************************************************************/
-
-static int video_maprgb (int r, int g, int b)
-{
-#ifdef VIDEO_MODE_YUYV
- unsigned int pR, pG, pB;
- tYUYV YUYV;
- unsigned int *ret = (unsigned int *) &YUYV;
-
- /* Transform (0-255) components to (0-100) */
-
- pR = r * 100 / 255;
- pG = g * 100 / 255;
- pB = b * 100 / 255;
-
- /* Calculate YUV values (0-255) from RGB beetween 0-100 */
-
- YUYV.Y1 = YUYV.Y2 = 209 * (pR + pG + pB) / 300 + 16;
- YUYV.U = pR - (pG * 3 / 4) - (pB / 4) + 128;
- YUYV.V = pB - (pR / 4) - (pG * 3 / 4) + 128;
- return *ret;
-#endif
-#ifdef VIDEO_MODE_RGB
- return ((r >> 3) << 11) | ((g > 2) << 6) | (b >> 3);
-#endif
-}
-
-static void video_setpalette (int color, int r, int g, int b)
-{
- color &= 0xf;
-
- video_palette[color] = video_maprgb (r, g, b);
-
- /* Swap values if our panning offset is odd */
- if (video_panning_value_x & 1)
- video_palette[color] = SWAPINT (video_palette[color]);
-}
-
-static void video_fill (int color)
-{
- memsetl (video_fb_address, VIDEO_PIX_BLOCKS, color);
-}
-
-static void video_setfgcolor (int i)
-{
- video_color_fg = i & 0xf;
-}
-
-static void video_setbgcolor (int i)
-{
- video_color_bg = i & 0xf;
-}
-
-static int video_pickcolor (int i)
-{
- return video_palette[i & 0xf];
-}
-
-/* Absolute console plotting functions */
-
-#ifdef VIDEO_BLINK
-static void video_revchar (int xx, int yy)
-{
- int rows;
- u8 *dest;
-
- dest = video_fb_address + yy * VIDEO_LINE_LEN + xx * 2;
-
- for (rows = VIDEO_FONT_HEIGHT; rows--; dest += VIDEO_LINE_LEN) {
- switch (VIDEO_FONT_WIDTH) {
- case 16:
- ((u32 *) dest)[6] ^= 0xffffffff;
- ((u32 *) dest)[7] ^= 0xffffffff;
- /* FALL THROUGH */
- case 12:
- ((u32 *) dest)[4] ^= 0xffffffff;
- ((u32 *) dest)[5] ^= 0xffffffff;
- /* FALL THROUGH */
- case 8:
- ((u32 *) dest)[2] ^= 0xffffffff;
- ((u32 *) dest)[3] ^= 0xffffffff;
- /* FALL THROUGH */
- case 4:
- ((u32 *) dest)[0] ^= 0xffffffff;
- ((u32 *) dest)[1] ^= 0xffffffff;
- }
- }
-}
-#endif
-
-static void video_drawchars (int xx, int yy, unsigned char *s, int count)
-{
- u8 *cdat, *dest, *dest0;
- int rows, offset, c;
- u32 eorx, fgx, bgx;
-
- offset = yy * VIDEO_LINE_LEN + xx * 2;
- dest0 = video_fb_address + offset;
-
- fgx = video_pickcolor (video_color_fg);
- bgx = video_pickcolor (video_color_bg);
-
- if (xx & 1) {
- fgx = SWAPINT (fgx);
- bgx = SWAPINT (bgx);
- }
-
- eorx = fgx ^ bgx;
-
- switch (VIDEO_FONT_WIDTH) {
- case 4:
- case 8:
- while (count--) {
- c = *s;
- cdat = video_fontdata + c * VIDEO_FONT_HEIGHT;
- for (rows = VIDEO_FONT_HEIGHT, dest = dest0;
- rows--;
- dest += VIDEO_LINE_LEN) {
- u8 bits = *cdat++;
-
- ((u32 *) dest)[0] =
- (video_font_draw_table[bits >> 6] & eorx) ^ bgx;
- ((u32 *) dest)[1] =
- (video_font_draw_table[bits >> 4 & 3] & eorx) ^ bgx;
- if (VIDEO_FONT_WIDTH == 8) {
- ((u32 *) dest)[2] =
- (video_font_draw_table[bits >> 2 & 3] & eorx) ^ bgx;
- ((u32 *) dest)[3] =
- (video_font_draw_table[bits & 3] & eorx) ^ bgx;
- }
- }
- dest0 += VIDEO_FONT_WIDTH * 2;
- s++;
- }
- break;
- case 12:
- case 16:
- while (count--) {
- cdat = video_fontdata + (*s) * (VIDEO_FONT_HEIGHT << 1);
- for (rows = VIDEO_FONT_HEIGHT, dest = dest0; rows--;
- dest += VIDEO_LINE_LEN) {
- u8 bits = *cdat++;
-
- ((u32 *) dest)[0] =
- (video_font_draw_table[bits >> 6] & eorx) ^ bgx;
- ((u32 *) dest)[1] =
- (video_font_draw_table[bits >> 4 & 3] & eorx) ^ bgx;
- ((u32 *) dest)[2] =
- (video_font_draw_table[bits >> 2 & 3] & eorx) ^ bgx;
- ((u32 *) dest)[3] =
- (video_font_draw_table[bits & 3] & eorx) ^ bgx;
- bits = *cdat++;
- ((u32 *) dest)[4] =
- (video_font_draw_table[bits >> 6] & eorx) ^ bgx;
- ((u32 *) dest)[5] =
- (video_font_draw_table[bits >> 4 & 3] & eorx) ^ bgx;
- if (VIDEO_FONT_WIDTH == 16) {
- ((u32 *) dest)[6] =
- (video_font_draw_table[bits >> 2 & 3] & eorx) ^ bgx;
- ((u32 *) dest)[7] =
- (video_font_draw_table[bits & 3] & eorx) ^ bgx;
- }
- }
- s++;
- dest0 += VIDEO_FONT_WIDTH * 2;
- }
- break;
- }
-}
-
-static inline void video_drawstring (int xx, int yy, char *s)
-{
- video_drawchars (xx, yy, (unsigned char *)s, strlen (s));
-}
-
-/* Relative to console plotting functions */
-
-static void video_putchars (int xx, int yy, unsigned char *s, int count)
-{
-#ifdef CONFIG_VIDEO_LOGO
- video_drawchars (xx, yy + VIDEO_LOGO_HEIGHT, s, count);
-#else
- video_drawchars (xx, yy, s, count);
-#endif
-}
-
-static void video_putchar (int xx, int yy, unsigned char c)
-{
-#ifdef CONFIG_VIDEO_LOGO
- video_drawchars (xx, yy + VIDEO_LOGO_HEIGHT, &c, 1);
-#else
- video_drawchars (xx, yy, &c, 1);
-#endif
-}
-
-static inline void video_putstring (int xx, int yy, unsigned char *s)
-{
- video_putchars (xx, yy, (unsigned char *)s, strlen ((char *)s));
-}
-
-/************************************************************************/
-/* ** VIDEO CONTROLLER LOW-LEVEL FUNCTIONS */
-/************************************************************************/
-
-static void video_mode_dupefield (VRAM * source, VRAM * dest, int entries)
-{
- int i;
-
- for (i = 0; i < entries; i++) {
- dest[i] = source[i]; /* Copy the entire record */
- dest[i].fx = (!dest[i].fx) * 3; /* Negate field bit */
- }
-
- dest[0].lcyc++; /* Add a cycle to the first entry */
- dest[entries - 1].lst = 1; /* Set end of ram entries */
-}
-
-static void inline video_mode_addentry (VRAM * vr,
- int Hx, int Vx, int Fx, int Bx,
- int VDS, int INT, int LCYC, int LP, int LST)
-{
- vr->hx = Hx;
- vr->vx = Vx;
- vr->fx = Fx;
- vr->bx = Bx;
- vr->vds = VDS;
- vr->inter = INT;
- vr->lcyc = LCYC;
- vr->lp = LP;
- vr->lst = LST;
-}
-
-#define ADDENTRY(a,b,c,d,e,f,g,h,i) video_mode_addentry(&vr[entry++],a,b,c,d,e,f,g,h,i)
-
-static int video_mode_generate (void)
-{
- immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- VRAM *vr = (VRAM *) (((void *) immap) + 0xb00); /* Pointer to the VRAM table */
- int DX, X1, X2, DY, Y1, Y2, entry = 0, fifo;
-
- /* CHECKING PARAMETERS */
-
- if (video_panning_factor_y < -128)
- video_panning_factor_y = -128;
-
- if (video_panning_factor_y > 128)
- video_panning_factor_y = 128;
-
- if (video_panning_factor_x < -128)
- video_panning_factor_x = -128;
-
- if (video_panning_factor_x > 128)
- video_panning_factor_x = 128;
-
- /* Setting panning */
-
- DX = video_panning_range_x = (VIDEO_ACTIVE_COLS - VIDEO_COLS) * 2;
- DY = video_panning_range_y = (VIDEO_ACTIVE_ROWS - VIDEO_ROWS) / 2;
-
- video_panning_value_x = (video_panning_factor_x + 128) * DX / 256;
- video_panning_value_y = (video_panning_factor_y + 128) * DY / 256;
-
- /* We assume these are burst units (multiplied by 2, we need it pari) */
- X1 = video_panning_value_x & 0xfffe;
- X2 = DX - X1;
-
- /* We assume these are field line units (divided by 2, we need it pari) */
- Y1 = video_panning_value_y & 0xfffe;
- Y2 = DY - Y1;
-
- debug("X1=%d, X2=%d, Y1=%d, Y2=%d, DX=%d, DY=%d VIDEO_COLS=%d \n",
- X1, X2, Y1, Y2, DX, DY, VIDEO_COLS);
-
-#ifdef VIDEO_MODE_NTSC
-/*
- * Hx Vx Fx Bx VDS INT LCYC LP LST
- *
- * Retrace blanking
- */
- ADDENTRY (0, 0, 3, 0, 1, 0, 3, 1, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 243, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 1440, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 32, 1, 0);
-/*
- * Vertical blanking
- */
- ADDENTRY (0, 0, 0, 0, 1, 0, 18, 1, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 243, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 1440, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 32, 1, 0);
-/*
- * Odd field active area (TOP)
- */
- if (Y1 > 0) {
- ADDENTRY (0, 0, 0, 0, 1, 0, Y1, 1, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 235, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, 1448, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 32, 1, 0);
- }
-/*
- * Odd field active area
- */
- ADDENTRY (0, 0, 0, 0, 1, 0, 240 - DY, 1, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 235, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, 8 + X1, 0, 0);
- ADDENTRY (3, 0, 0, 3, 0, 0, VIDEO_COLS * 2, 0, 0);
-
- if (X2 > 0)
- ADDENTRY (3, 0, 0, 3, 1, 0, X2, 0, 0);
-
- ADDENTRY (3, 0, 0, 0, 1, 0, 32, 1, 0);
-
-/*
- * Odd field active area (BOTTOM)
- */
- if (Y1 > 0) {
- ADDENTRY (0, 0, 0, 0, 1, 0, Y2, 1, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 235, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, 1448, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 32, 1, 0);
- }
-/*
- * Vertical blanking
- */
- ADDENTRY (0, 0, 0, 0, 1, 0, 4, 1, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 243, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 1440, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 32, 1, 0);
-/*
- * Vertical blanking
- */
- ADDENTRY (0, 0, 3, 0, 1, 0, 19, 1, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 243, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 1440, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 32, 1, 0);
-/*
- * Even field active area (TOP)
- */
- if (Y1 > 0) {
- ADDENTRY (0, 0, 3, 0, 1, 0, Y1, 1, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 235, 0, 0);
- ADDENTRY (3, 0, 3, 3, 1, 0, 1448, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 32, 1, 0);
- }
-/*
- * Even field active area (CENTER)
- */
- ADDENTRY (0, 0, 3, 0, 1, 0, 240 - DY, 1, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 235, 0, 0);
- ADDENTRY (3, 0, 3, 3, 1, 0, 8 + X1, 0, 0);
- ADDENTRY (3, 0, 3, 3, 0, 0, VIDEO_COLS * 2, 0, 0);
-
- if (X2 > 0)
- ADDENTRY (3, 0, 3, 3, 1, 0, X2, 0, 0);
-
- ADDENTRY (3, 0, 3, 0, 1, 0, 32, 1, 0);
-/*
- * Even field active area (BOTTOM)
- */
- if (Y1 > 0) {
- ADDENTRY (0, 0, 3, 0, 1, 0, Y2, 1, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 235, 0, 0);
- ADDENTRY (3, 0, 3, 3, 1, 0, 1448, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 32, 1, 0);
- }
-/*
- * Vertical blanking
- */
- ADDENTRY (0, 0, 3, 0, 1, 0, 1, 1, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 243, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 0, 1440, 0, 0);
- ADDENTRY (3, 0, 3, 0, 1, 1, 32, 1, 1);
-#endif
-
-#ifdef VIDEO_MODE_PAL
-
-/*
- * Hx Vx Fx Bx VDS INT LCYC LP LST
- *
- * vertical; blanking
- */
- ADDENTRY (0, 0, 0, 0, 1, 0, 22, 1, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 263, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 1440, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 24, 1, 0);
-/*
- * active area (TOP)
- */
- if (Y1 > 0) {
- ADDENTRY (0, 0, 0, 0, 1, 0, Y1, 1, 0); /* 11? */
- ADDENTRY (3, 0, 0, 0, 1, 0, 255, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, 1448, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 24, 1, 0);
- }
-/*
- * field active area (CENTER)
- */
- ADDENTRY (0, 0, 0, 0, 1, 0, 288 - DY, 1, 0); /* 265? */
- ADDENTRY (3, 0, 0, 0, 1, 0, 255, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, 8 + X1, 0, 0);
- ADDENTRY (3, 0, 0, 3, 0, 0, VIDEO_COLS * 2, 0, 0);
-
- if (X2 > 0)
- ADDENTRY (3, 0, 0, 1, 1, 0, X2, 0, 0);
-
- ADDENTRY (3, 0, 0, 0, 1, 0, 24, 1, 0);
-/*
- * field active area (BOTTOM)
- */
- if (Y2 > 0) {
- ADDENTRY (0, 0, 0, 0, 1, 0, Y2, 1, 0); /* 12? */
- ADDENTRY (3, 0, 0, 0, 1, 0, 255, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, 1448, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 24, 1, 0);
- }
-/*
- * field vertical; blanking
- */
- ADDENTRY (0, 0, 0, 0, 1, 0, 2, 1, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 263, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 1440, 0, 0);
- ADDENTRY (3, 0, 0, 0, 1, 0, 24, 1, 0);
-/*
- * Create the other field (like this, but whit other field selected,
- * one more cycle loop and a last identifier)
- */
- video_mode_dupefield (vr, &vr[entry], entry);
-
-#endif /* VIDEO_MODE_PAL */
-
- /* See what FIFO are we using */
- fifo = GETBIT (immap->im_vid.vid_vsr, VIDEO_VSR_CAS);
-
- /* Set number of lines and burst (only one frame for now) */
- if (fifo) {
- immap->im_vid.vid_vfcr0 = VIDEO_BURST_LEN |
- (VIDEO_BURST_LEN << 8) | ((VIDEO_ROWS / 2) << 19);
- } else {
- immap->im_vid.vid_vfcr1 = VIDEO_BURST_LEN |
- (VIDEO_BURST_LEN << 8) | ((VIDEO_ROWS / 2) << 19);
- }
-
- SETBIT (immap->im_vid.vid_vcmr, VIDEO_VCMR_ASEL, !fifo);
-
-/*
- * Wait until changes are applied (not done)
- * while (GETBIT(immap->im_vid.vid_vsr, VIDEO_VSR_CAS) == fifo) ;
- */
-
- /* Return number of VRAM entries */
- return entry * 2;
-}
-
-static void video_encoder_init (void)
-{
- return;
-}
-
-static void video_ctrl_init (void *memptr)
-{
- immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- video_fb_address = memptr;
-
- /* Set background */
- debug ("[VIDEO CTRL] Setting background color...\n");
- immap->im_vid.vid_vbcb = VIDEO_BG_COL;
-
- /* Show the background */
- debug ("[VIDEO CTRL] Forcing background...\n");
- SETBIT (immap->im_vid.vid_vcmr, VIDEO_VCMR_BD, 1);
-
- /* Turn off video controller */
- debug ("[VIDEO CTRL] Turning off video controller...\n");
- SETBIT (immap->im_vid.vid_vccr, VIDEO_VCCR_VON, 0);
-
- /* Generate and make active a new video mode */
- debug ("[VIDEO CTRL] Generating video mode...\n");
- video_mode_generate ();
-
- /* Start of frame buffer (even and odd frame, to make it working with */
- /* any selected active set) */
- debug ("[VIDEO CTRL] Setting frame buffer address...\n");
- immap->im_vid.vid_vfaa1 =
- immap->im_vid.vid_vfaa0 = (u32) video_fb_address;
- immap->im_vid.vid_vfba1 =
- immap->im_vid.vid_vfba0 =
- (u32) video_fb_address + VIDEO_LINE_LEN;
-
- /* YUV, Big endian, SHIFT/CLK/CLK input (BEFORE ENABLING 27MHZ EXT CLOCK) */
- debug ("[VIDEO CTRL] Setting pixel mode and clocks...\n");
- immap->im_vid.vid_vccr = 0x2042;
-
- /* Configure port pins */
- debug ("[VIDEO CTRL] Configuring input/output pins...\n");
- immap->im_ioport.iop_pdpar = 0x1fff;
- immap->im_ioport.iop_pddir = 0x0000;
-
- /* Blanking the screen. */
- debug ("[VIDEO CTRL] Blanking the screen...\n");
- video_fill (VIDEO_BG_COL);
-
- /*
- * Turns on Aggressive Mode. Normally, turning on the caches
- * will cause the screen to flicker when the caches try to
- * fill. This gives the FIFO's for the Video Controller
- * higher priority and prevents flickering because of
- * underrun. This may still be an issue when using FLASH,
- * since accessing data from Flash is so slow.
- */
- debug ("[VIDEO CTRL] Turning on aggressive mode...\n");
- immap->im_siu_conf.sc_sdcr = 0x40;
-
- /* Turn on video controller */
- debug ("[VIDEO CTRL] Turning on video controller...\n");
- SETBIT (immap->im_vid.vid_vccr, VIDEO_VCCR_VON, 1);
-
- /* Show the display */
- debug ("[VIDEO CTRL] Enabling the video...\n");
- SETBIT (immap->im_vid.vid_vcmr, VIDEO_VCMR_BD, 0);
-}
-
-/************************************************************************/
-/* ** CONSOLE FUNCTIONS */
-/************************************************************************/
-
-static void console_scrollup (void)
-{
- /* Copy up rows ignoring the first one */
- memcpyl (CONSOLE_ROW_FIRST, CONSOLE_ROW_SECOND, CONSOLE_SCROLL_SIZE >> 2);
-
- /* Clear the last one */
- memsetl (CONSOLE_ROW_LAST, CONSOLE_ROW_SIZE >> 2, VIDEO_BG_COL);
-}
-
-static inline void console_back (void)
-{
- console_col--;
-
- if (console_col < 0) {
- console_col = CONSOLE_COLS - 1;
- console_row--;
- if (console_row < 0)
- console_row = 0;
- }
-
- video_putchar ( console_col * VIDEO_FONT_WIDTH,
- console_row * VIDEO_FONT_HEIGHT, ' ');
-}
-
-static inline void console_newline (void)
-{
- console_row++;
- console_col = 0;
-
- /* Check if we need to scroll the terminal */
- if (console_row >= CONSOLE_ROWS) {
- /* Scroll everything up */
- console_scrollup ();
-
- /* Decrement row number */
- console_row--;
- }
-}
-
-void video_putc(struct stdio_dev *dev, const char c)
-{
- if (!video_enable) {
- serial_putc (c);
- return;
- }
-
- switch (c) {
- case 13: /* Simply ignore this */
- break;
-
- case '\n': /* Next line, please */
- console_newline ();
- break;
-
- case 9: /* Tab (8 chars alignment) */
- console_col |= 0x0008; /* Next 8 chars boundary */
- console_col &= ~0x0007; /* Set this bit to zero */
-
- if (console_col >= CONSOLE_COLS)
- console_newline ();
- break;
-
- case 8: /* Eat last character */
- console_back ();
- break;
-
- default: /* Add to the console */
- video_putchar ( console_col * VIDEO_FONT_WIDTH,
- console_row * VIDEO_FONT_HEIGHT, c);
- console_col++;
- /* Check if we need to go to next row */
- if (console_col >= CONSOLE_COLS)
- console_newline ();
- }
-}
-
-void video_puts(struct stdio_dev *dev, const char *s)
-{
- int count = strlen (s);
-
- if (!video_enable)
- while (count--)
- serial_putc (*s++);
- else
- while (count--)
- video_putc(dev, *s++);
-}
-
-/************************************************************************/
-/* ** CURSOR BLINKING FUNCTIONS */
-/************************************************************************/
-
-#ifdef VIDEO_BLINK
-
-#define BLINK_TIMER_ID 0
-#define BLINK_TIMER_HZ 2
-
-static unsigned char blink_enabled = 0;
-static timer_t blink_timer;
-
-static void blink_update (void)
-{
- static int blink_row = -1, blink_col = -1, blink_old = 0;
-
- /* Check if we have a new position to invert */
- if ((console_row != blink_row) || (console_col != blink_col)) {
- /* Check if we need to reverse last character */
- if (blink_old)
- video_revchar ( blink_col * VIDEO_FONT_WIDTH,
- (blink_row
-#ifdef CONFIG_VIDEO_LOGO
- + VIDEO_LOGO_HEIGHT
-#endif
- ) * VIDEO_FONT_HEIGHT);
-
- /* Update values */
- blink_row = console_row;
- blink_col = console_col;
- blink_old = 0;
- }
-
-/* Reverse this character */
- blink_old = !blink_old;
- video_revchar ( console_col * VIDEO_FONT_WIDTH,
- (console_row
-#ifdef CONFIG_VIDEO_LOGO
- + VIDEO_LOGO_HEIGHT
-#endif
- ) * VIDEO_FONT_HEIGHT);
-
-}
-
-/*
- * Handler for blinking cursor
- */
-static void blink_handler (void *arg)
-{
-/* Blink */
- blink_update ();
-/* Ack the timer */
- timer_ack (&blink_timer);
-}
-
-int blink_set (int blink)
-{
- int ret = blink_enabled;
-
- if (blink)
- timer_enable (&blink_timer);
- else
- timer_disable (&blink_timer);
-
- blink_enabled = blink;
-
- return ret;
-}
-
-static inline void blink_close (void)
-{
- timer_close (&blink_timer);
-}
-
-static inline void blink_init (void)
-{
- timer_init (&blink_timer,
- BLINK_TIMER_ID, BLINK_TIMER_HZ,
- blink_handler);
-}
-#endif
-
-/************************************************************************/
-/* ** LOGO PLOTTING FUNCTIONS */
-/************************************************************************/
-
-#ifdef CONFIG_VIDEO_LOGO
-void easylogo_plot (fastimage_t * image, void *screen, int width, int x,
- int y)
-{
- int skip = width - image->width, xcount, ycount = image->height;
-
-#ifdef VIDEO_MODE_YUYV
- ushort *source = (ushort *) image->data;
- ushort *dest = (ushort *) screen + y * width + x;
-
- while (ycount--) {
- xcount = image->width;
- while (xcount--)
- *dest++ = *source++;
- dest += skip;
- }
-#endif
-#ifdef VIDEO_MODE_RGB
- unsigned char
- *source = (unsigned short *) image->data,
- *dest = (unsigned short *) screen + ((y * width) + x) * 3;
-
- while (ycount--) {
- xcount = image->width * 3;
- memcpy (dest, source, xcount);
- source += xcount;
- dest += ycount;
- }
-#endif
-}
-
-static void *video_logo (void)
-{
- u16 *screen = video_fb_address, width = VIDEO_COLS;
-#ifdef VIDEO_INFO
- char temp[32];
- char info[80];
-#endif /* VIDEO_INFO */
-
- easylogo_plot (VIDEO_LOGO_ADDR, screen, width, 0, 0);
-
-#ifdef VIDEO_INFO
- sprintf (info, "%s (%s - %s) ",
- U_BOOT_VERSION, U_BOOT_DATE, U_BOOT_TIME);
- video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y, info);
-
- strcpy(info, "(C) 2002 DENX Software Engineering");
- video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y + VIDEO_FONT_HEIGHT,
- info);
-
- strcpy(info, " Wolfgang DENK, wd@denx.de");
- video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y + VIDEO_FONT_HEIGHT * 2,
- info);
-
- /* leave one blank line */
-
- sprintf(info, "MPC823 CPU at %s MHz, %ld MiB RAM, %ld MiB Flash",
- strmhz(temp, gd->cpu_clk),
- gd->ram_size >> 20,
- gd->bd->bi_flashsize >> 20 );
- video_drawstring (VIDEO_INFO_X, VIDEO_INFO_Y + VIDEO_FONT_HEIGHT * 4,
- info);
-#endif
-
- return video_fb_address + VIDEO_LOGO_HEIGHT * VIDEO_LINE_LEN;
-}
-#endif
-
-/************************************************************************/
-/* ** VIDEO HIGH-LEVEL FUNCTIONS */
-/************************************************************************/
-
-static int video_init (void *videobase)
-{
- /* Initialize the encoder */
- debug ("[VIDEO] Initializing video encoder...\n");
- video_encoder_init ();
-
- /* Initialize the video controller */
- debug ("[VIDEO] Initializing video controller at %08x...\n",
- (int) videobase);
- video_ctrl_init (videobase);
-
- /* Setting the palette */
- video_setpalette (CONSOLE_COLOR_BLACK, 0, 0, 0);
- video_setpalette (CONSOLE_COLOR_RED, 0xFF, 0, 0);
- video_setpalette (CONSOLE_COLOR_GREEN, 0, 0xFF, 0);
- video_setpalette (CONSOLE_COLOR_YELLOW, 0xFF, 0xFF, 0);
- video_setpalette (CONSOLE_COLOR_BLUE, 0, 0, 0xFF);
- video_setpalette (CONSOLE_COLOR_MAGENTA, 0xFF, 0, 0xFF);
- video_setpalette (CONSOLE_COLOR_CYAN, 0, 0xFF, 0xFF);
- video_setpalette (CONSOLE_COLOR_GREY, 0xAA, 0xAA, 0xAA);
- video_setpalette (CONSOLE_COLOR_GREY2, 0xF8, 0xF8, 0xF8);
- video_setpalette (CONSOLE_COLOR_WHITE, 0xFF, 0xFF, 0xFF);
-
-#ifndef CONFIG_SYS_WHITE_ON_BLACK
- video_setfgcolor (CONSOLE_COLOR_BLACK);
- video_setbgcolor (CONSOLE_COLOR_GREY2);
-#else
- video_setfgcolor (CONSOLE_COLOR_GREY2);
- video_setbgcolor (CONSOLE_COLOR_BLACK);
-#endif /* CONFIG_SYS_WHITE_ON_BLACK */
-
-#ifdef CONFIG_VIDEO_LOGO
- /* Paint the logo and retrieve tv base address */
- debug ("[VIDEO] Drawing the logo...\n");
- video_console_address = video_logo ();
-#else
- video_console_address = video_fb_address;
-#endif
-
-#ifdef VIDEO_BLINK
- /* Enable the blinking (under construction) */
- blink_init ();
- blink_set (0); /* To Fix! */
-#endif
-
- /* Initialize the console */
- console_col = 0;
- console_row = 0;
- video_enable = 1;
-
-#ifdef VIDEO_MODE_PAL
-# define VIDEO_MODE_TMP1 "PAL"
-#endif
-#ifdef VIDEO_MODE_NTSC
-# define VIDEO_MODE_TMP1 "NTSC"
-#endif
-#ifdef VIDEO_MODE_YUYV
-# define VIDEO_MODE_TMP2 "YCbYCr"
-#endif
-#ifdef VIDEO_MODE_RGB
-# define VIDEO_MODE_TMP2 "RGB"
-#endif
- debug ( VIDEO_MODE_TMP1
- " %dx%dx%d (" VIDEO_MODE_TMP2 ") on %s - console %dx%d\n",
- VIDEO_COLS, VIDEO_ROWS, VIDEO_MODE_BPP,
- VIDEO_ENCODER_NAME, CONSOLE_COLS, CONSOLE_ROWS);
- return 0;
-}
-
-int drv_video_init (void)
-{
- int error, devices = 1;
-
- struct stdio_dev videodev;
-
- video_init ((void *)(gd->fb_base)); /* Video initialization */
-
-/* Device initialization */
-
- memset (&videodev, 0, sizeof (videodev));
-
- strcpy (videodev.name, "video");
- videodev.flags = DEV_FLAGS_OUTPUT; /* Output only */
- videodev.putc = video_putc; /* 'putc' function */
- videodev.puts = video_puts; /* 'puts' function */
-
- error = stdio_register (&videodev);
-
- return (error == 0) ? devices : error;
-}
-
-/************************************************************************/
-/* ** ROM capable initialization part - needed to reserve FB memory */
-/************************************************************************/
-
-/*
- * This is called early in the system initialization to grab memory
- * for the video controller.
- * Returns new address for monitor, after reserving video buffer memory
- *
- * Note that this is running from ROM, so no write access to global data.
- */
-ulong video_setmem (ulong addr)
-{
- /* Allocate pages for the frame buffer. */
- addr -= VIDEO_SIZE;
-
- debug ("Reserving %dk for Video Framebuffer at: %08lx\n",
- VIDEO_SIZE>>10, addr);
-
- return (addr);
-}
-
-#endif
diff --git a/arch/powerpc/cpu/ppc4xx/4xx_uart.c b/arch/powerpc/cpu/ppc4xx/4xx_uart.c
index c02058f79bba253ad9cfa6b90155d3f47ac6dfde..bca839378dbd8af1f7f8cf3bd6488774648be2ed 100644
--- a/arch/powerpc/cpu/ppc4xx/4xx_uart.c
+++ b/arch/powerpc/cpu/ppc4xx/4xx_uart.c
@@ -9,7 +9,6 @@
*/
#include <common.h>
-#include <commproc.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <watchdog.h>
diff --git a/arch/powerpc/cpu/ppc4xx/interrupts.c b/arch/powerpc/cpu/ppc4xx/interrupts.c
index 45997d6eae0640dee7e36cffdcf1460afd336379..599f2c21cf114d6725270c89cb0a5fcff0413917 100644
--- a/arch/powerpc/cpu/ppc4xx/interrupts.c
+++ b/arch/powerpc/cpu/ppc4xx/interrupts.c
@@ -22,7 +22,6 @@
#include <asm/interrupt.h>
#include <asm/ppc4xx.h>
#include <ppc_asm.tmpl>
-#include <commproc.h>
DECLARE_GLOBAL_DATA_PTR;
diff --git a/arch/powerpc/cpu/ppc4xx/miiphy.c b/arch/powerpc/cpu/ppc4xx/miiphy.c
index aef267e0a2bf008cc6dc57a03120a00f7b3c558f..6273772ee07e84b06c15e6e73498ee9d12e2091b 100644
--- a/arch/powerpc/cpu/ppc4xx/miiphy.c
+++ b/arch/powerpc/cpu/ppc4xx/miiphy.c
@@ -21,7 +21,6 @@
#include <asm/processor.h>
#include <asm/io.h>
#include <ppc_asm.tmpl>
-#include <commproc.h>
#include <asm/ppc4xx.h>
#include <asm/ppc4xx-emac.h>
#include <asm/ppc4xx-mal.h>
diff --git a/arch/powerpc/cpu/ppc4xx/uic.c b/arch/powerpc/cpu/ppc4xx/uic.c
index fb453b1adfb51bdf09cb3fe229bd6652cde35a63..acc232dcf21d50aac2c6b75eb3d6babce8e4ed17 100644
--- a/arch/powerpc/cpu/ppc4xx/uic.c
+++ b/arch/powerpc/cpu/ppc4xx/uic.c
@@ -22,7 +22,6 @@
#include <asm/interrupt.h>
#include <asm/ppc4xx.h>
#include <ppc_asm.tmpl>
-#include <commproc.h>
#if (UIC_MAX > 3)
#define UICB0_ALL (UIC_MASK(VECNUM_UIC1CI) | UIC_MASK(VECNUM_UIC1NCI) | \
diff --git a/arch/powerpc/cpu/ppc4xx/xilinx_irq.c b/arch/powerpc/cpu/ppc4xx/xilinx_irq.c
index 1a2e917eb23b032f83fc5c3cd6e00c9659c8ebab..acb933e08b291e26262d2b0a89933eb9c46440b7 100644
--- a/arch/powerpc/cpu/ppc4xx/xilinx_irq.c
+++ b/arch/powerpc/cpu/ppc4xx/xilinx_irq.c
@@ -12,7 +12,6 @@
#include <asm/interrupt.h>
#include <asm/ppc4xx.h>
#include <ppc_asm.tmpl>
-#include <commproc.h>
#include <asm/io.h>
#include <asm/xilinx_irq.h>
diff --git a/arch/powerpc/include/asm/8xx_immap.h b/arch/powerpc/include/asm/8xx_immap.h
deleted file mode 100644
index dfaddb6f1d4c32851d38567de4da9fb5bb25b548..0000000000000000000000000000000000000000
--- a/arch/powerpc/include/asm/8xx_immap.h
+++ /dev/null
@@ -1,515 +0,0 @@
-/*
- * MPC8xx Internal Memory Map
- * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
- *
- * The I/O on the MPC860 is comprised of blocks of special registers
- * and the dual port ram for the Communication Processor Module.
- * Within this space are functional units such as the SIU, memory
- * controller, system timers, and other control functions. It is
- * a combination that I found difficult to separate into logical
- * functional files.....but anyone else is welcome to try. -- Dan
- */
-#ifndef __IMMAP_8XX__
-#define __IMMAP_8XX__
-
-/* System configuration registers.
-*/
-typedef struct sys_conf {
- uint sc_siumcr;
- uint sc_sypcr;
- uint sc_swt;
- char res1[2];
- ushort sc_swsr;
- uint sc_sipend;
- uint sc_simask;
- uint sc_siel;
- uint sc_sivec;
- uint sc_tesr;
- char res2[0xc];
- uint sc_sdcr;
- char res3[0x4c];
-} sysconf8xx_t;
-
-/* PCMCIA configuration registers.
-*/
-typedef struct pcmcia_conf {
- uint pcmc_pbr0;
- uint pcmc_por0;
- uint pcmc_pbr1;
- uint pcmc_por1;
- uint pcmc_pbr2;
- uint pcmc_por2;
- uint pcmc_pbr3;
- uint pcmc_por3;
- uint pcmc_pbr4;
- uint pcmc_por4;
- uint pcmc_pbr5;
- uint pcmc_por5;
- uint pcmc_pbr6;
- uint pcmc_por6;
- uint pcmc_pbr7;
- uint pcmc_por7;
- char res1[0x20];
- uint pcmc_pgcra;
- uint pcmc_pgcrb;
- uint pcmc_pscr;
- char res2[4];
- uint pcmc_pipr;
- char res3[4];
- uint pcmc_per;
- char res4[4];
-} pcmconf8xx_t;
-
-/* Memory controller registers.
-*/
-typedef struct mem_ctlr {
- uint memc_br0;
- uint memc_or0;
- uint memc_br1;
- uint memc_or1;
- uint memc_br2;
- uint memc_or2;
- uint memc_br3;
- uint memc_or3;
- uint memc_br4;
- uint memc_or4;
- uint memc_br5;
- uint memc_or5;
- uint memc_br6;
- uint memc_or6;
- uint memc_br7;
- uint memc_or7;
- char res1[0x24];
- uint memc_mar;
- uint memc_mcr;
- char res2[4];
- uint memc_mamr;
- uint memc_mbmr;
- ushort memc_mstat;
- ushort memc_mptpr;
- uint memc_mdr;
- char res3[0x80];
-} memctl8xx_t;
-
-/* System Integration Timers.
-*/
-typedef struct sys_int_timers {
- ushort sit_tbscr;
- char res0[0x02];
- uint sit_tbreff0;
- uint sit_tbreff1;
- char res1[0x14];
- ushort sit_rtcsc;
- char res2[0x02];
- uint sit_rtc;
- uint sit_rtsec;
- uint sit_rtcal;
- char res3[0x10];
- ushort sit_piscr;
- char res4[2];
- uint sit_pitc;
- uint sit_pitr;
- char res5[0x34];
-} sit8xx_t;
-
-#define TBSCR_TBIRQ_MASK ((ushort)0xff00)
-#define TBSCR_REFA ((ushort)0x0080)
-#define TBSCR_REFB ((ushort)0x0040)
-#define TBSCR_REFAE ((ushort)0x0008)
-#define TBSCR_REFBE ((ushort)0x0004)
-#define TBSCR_TBF ((ushort)0x0002)
-#define TBSCR_TBE ((ushort)0x0001)
-
-#define RTCSC_RTCIRQ_MASK ((ushort)0xff00)
-#define RTCSC_SEC ((ushort)0x0080)
-#define RTCSC_ALR ((ushort)0x0040)
-#define RTCSC_38K ((ushort)0x0010)
-#define RTCSC_SIE ((ushort)0x0008)
-#define RTCSC_ALE ((ushort)0x0004)
-#define RTCSC_RTF ((ushort)0x0002)
-#define RTCSC_RTE ((ushort)0x0001)
-
-#define PISCR_PIRQ_MASK ((ushort)0xff00)
-#define PISCR_PS ((ushort)0x0080)
-#define PISCR_PIE ((ushort)0x0004)
-#define PISCR_PTF ((ushort)0x0002)
-#define PISCR_PTE ((ushort)0x0001)
-
-/* Clocks and Reset.
-*/
-typedef struct clk_and_reset {
- uint car_sccr;
- uint car_plprcr;
- uint car_rsr;
- char res[0x74]; /* Reserved area */
-} car8xx_t;
-
-/* System Integration Timers keys.
-*/
-typedef struct sitk {
- uint sitk_tbscrk;
- uint sitk_tbreff0k;
- uint sitk_tbreff1k;
- uint sitk_tbk;
- char res1[0x10];
- uint sitk_rtcsck;
- uint sitk_rtck;
- uint sitk_rtseck;
- uint sitk_rtcalk;
- char res2[0x10];
- uint sitk_piscrk;
- uint sitk_pitck;
- char res3[0x38];
-} sitk8xx_t;
-
-/* Clocks and reset keys.
-*/
-typedef struct cark {
- uint cark_sccrk;
- uint cark_plprcrk;
- uint cark_rsrk;
- char res[0x474];
-} cark8xx_t;
-
-/* The key to unlock registers maintained by keep-alive power.
-*/
-#define KAPWR_KEY ((unsigned int)0x55ccaa33)
-
-/* Video interface. MPC823 Only.
-*/
-typedef struct vid823 {
- ushort vid_vccr;
- ushort res1;
- u_char vid_vsr;
- u_char res2;
- u_char vid_vcmr;
- u_char res3;
- uint vid_vbcb;
- uint res4;
- uint vid_vfcr0;
- uint vid_vfaa0;
- uint vid_vfba0;
- uint vid_vfcr1;
- uint vid_vfaa1;
- uint vid_vfba1;
- u_char res5[0x18];
-} vid823_t;
-
-/* LCD interface. 823 Only.
-*/
-typedef struct lcd {
- uint lcd_lccr;
- uint lcd_lchcr;
- uint lcd_lcvcr;
- char res1[4];
- uint lcd_lcfaa;
- uint lcd_lcfba;
- char lcd_lcsr;
- char res2[0x7];
-} lcd823_t;
-
-/* I2C
-*/
-typedef struct i2c {
- u_char i2c_i2mod;
- char res1[3];
- u_char i2c_i2add;
- char res2[3];
- u_char i2c_i2brg;
- char res3[3];
- u_char i2c_i2com;
- char res4[3];
- u_char i2c_i2cer;
- char res5[3];
- u_char i2c_i2cmr;
- char res6[0x8b];
-} i2c8xx_t;
-
-/* DMA control/status registers.
-*/
-typedef struct sdma_csr {
- char res1[4];
- uint sdma_sdar;
- u_char sdma_sdsr;
- char res3[3];
- u_char sdma_sdmr;
- char res4[3];
- u_char sdma_idsr1;
- char res5[3];
- u_char sdma_idmr1;
- char res6[3];
- u_char sdma_idsr2;
- char res7[3];
- u_char sdma_idmr2;
- char res8[0x13];
-} sdma8xx_t;
-
-/* Communication Processor Module Interrupt Controller.
-*/
-typedef struct cpm_ic {
- ushort cpic_civr;
- char res[0xe];
- uint cpic_cicr;
- uint cpic_cipr;
- uint cpic_cimr;
- uint cpic_cisr;
-} cpic8xx_t;
-
-/* Input/Output Port control/status registers.
-*/
-typedef struct io_port {
- ushort iop_padir;
- ushort iop_papar;
- ushort iop_paodr;
- ushort iop_padat;
- char res1[8];
- ushort iop_pcdir;
- ushort iop_pcpar;
- ushort iop_pcso;
- ushort iop_pcdat;
- ushort iop_pcint;
- char res2[6];
- ushort iop_pddir;
- ushort iop_pdpar;
- char res3[2];
- ushort iop_pddat;
- uint utmode;
- char res4[4];
-} iop8xx_t;
-
-/* Communication Processor Module Timers
-*/
-typedef struct cpm_timers {
- ushort cpmt_tgcr;
- char res1[0xe];
- ushort cpmt_tmr1;
- ushort cpmt_tmr2;
- ushort cpmt_trr1;
- ushort cpmt_trr2;
- ushort cpmt_tcr1;
- ushort cpmt_tcr2;
- ushort cpmt_tcn1;
- ushort cpmt_tcn2;
- ushort cpmt_tmr3;
- ushort cpmt_tmr4;
- ushort cpmt_trr3;
- ushort cpmt_trr4;
- ushort cpmt_tcr3;
- ushort cpmt_tcr4;
- ushort cpmt_tcn3;
- ushort cpmt_tcn4;
- ushort cpmt_ter1;
- ushort cpmt_ter2;
- ushort cpmt_ter3;
- ushort cpmt_ter4;
- char res2[8];
-} cpmtimer8xx_t;
-
-/* Finally, the Communication Processor stuff.....
-*/
-typedef struct scc { /* Serial communication channels */
- uint scc_gsmrl;
- uint scc_gsmrh;
- ushort scc_psmr;
- char res1[2];
- ushort scc_todr;
- ushort scc_dsr;
- ushort scc_scce;
- char res2[2];
- ushort scc_sccm;
- char res3;
- u_char scc_sccs;
- char res4[8];
-} scc_t;
-
-typedef struct smc { /* Serial management channels */
- char res1[2];
- ushort smc_smcmr;
- char res2[2];
- u_char smc_smce;
- char res3[3];
- u_char smc_smcm;
- char res4[5];
-} smc_t;
-
-/* MPC860T Fast Ethernet Controller. It isn't part of the CPM, but
- * it fits within the address space.
- */
-
-typedef struct fec {
- uint fec_addr_low; /* lower 32 bits of station address */
- ushort fec_addr_high; /* upper 16 bits of station address */
- ushort res1; /* reserved */
- uint fec_hash_table_high; /* upper 32-bits of hash table */
- uint fec_hash_table_low; /* lower 32-bits of hash table */
- uint fec_r_des_start; /* beginning of Rx descriptor ring */
- uint fec_x_des_start; /* beginning of Tx descriptor ring */
- uint fec_r_buff_size; /* Rx buffer size */
- uint res2[9]; /* reserved */
- uint fec_ecntrl; /* ethernet control register */
- uint fec_ievent; /* interrupt event register */
- uint fec_imask; /* interrupt mask register */
- uint fec_ivec; /* interrupt level and vector status */
- uint fec_r_des_active; /* Rx ring updated flag */
- uint fec_x_des_active; /* Tx ring updated flag */
- uint res3[10]; /* reserved */
- uint fec_mii_data; /* MII data register */
- uint fec_mii_speed; /* MII speed control register */
- uint res4[17]; /* reserved */
- uint fec_r_bound; /* end of RAM (read-only) */
- uint fec_r_fstart; /* Rx FIFO start address */
- uint res5[6]; /* reserved */
- uint fec_x_fstart; /* Tx FIFO start address */
- uint res6[17]; /* reserved */
- uint fec_fun_code; /* fec SDMA function code */
- uint res7[3]; /* reserved */
- uint fec_r_cntrl; /* Rx control register */
- uint fec_r_hash; /* Rx hash register */
- uint res8[14]; /* reserved */
- uint fec_x_cntrl; /* Tx control register */
- uint res9[0x1e]; /* reserved */
-} fec_t;
-
-/* The FEC and LCD color map share the same address space....
- * I guess we will never see an 823T :-).
- */
-union fec_lcd {
- fec_t fl_un_fec;
- u_char fl_un_cmap[0x200];
-};
-
-typedef struct comm_proc {
- /* General control and status registers.
- */
- ushort cp_cpcr;
- u_char res1[2];
- ushort cp_rccr;
- u_char res2;
- u_char cp_rmds;
- u_char res3[4];
- ushort cp_cpmcr1;
- ushort cp_cpmcr2;
- ushort cp_cpmcr3;
- ushort cp_cpmcr4;
- u_char res4[2];
- ushort cp_rter;
- u_char res5[2];
- ushort cp_rtmr;
- u_char res6[0x14];
-
- /* Baud rate generators.
- */
- uint cp_brgc1;
- uint cp_brgc2;
- uint cp_brgc3;
- uint cp_brgc4;
-
- /* Serial Communication Channels.
- */
- scc_t cp_scc[4];
-
- /* Serial Management Channels.
- */
- smc_t cp_smc[2];
-
- /* Serial Peripheral Interface.
- */
- ushort cp_spmode;
- u_char res7[4];
- u_char cp_spie;
- u_char res8[3];
- u_char cp_spim;
- u_char res9[2];
- u_char cp_spcom;
- u_char res10[2];
-
- /* Parallel Interface Port.
- */
- u_char res11[2];
- ushort cp_pipc;
- u_char res12[2];
- ushort cp_ptpr;
- uint cp_pbdir;
- uint cp_pbpar;
- u_char res13[2];
- ushort cp_pbodr;
- uint cp_pbdat;
-
- /* Port E - MPC87x/88x only.
- */
- uint cp_pedir;
- uint cp_pepar;
- uint cp_peso;
- uint cp_peodr;
- uint cp_pedat;
-
- /* Communications Processor Timing Register -
- Contains RMII Timing for the FECs on MPC87x/88x only.
- */
- uint cp_cptr;
-
- /* Serial Interface and Time Slot Assignment.
- */
- uint cp_simode;
- u_char cp_sigmr;
- u_char res15;
- u_char cp_sistr;
- u_char cp_sicmr;
- u_char res16[4];
- uint cp_sicr;
- uint cp_sirp;
- u_char res17[0xc];
-
- /* 256 bytes of MPC823 video controller RAM array.
- */
- u_char cp_vcram[0x100];
- u_char cp_siram[0x200];
-
- /* The fast ethernet controller is not really part of the CPM,
- * but it resides in the address space.
- * The LCD color map is also here.
- */
- union fec_lcd fl_un;
-#define cp_fec fl_un.fl_un_fec
-#define lcd_cmap fl_un.fl_un_cmap
- char res18[0xE00];
-
- /* The MPC885 family has a second FEC here */
- fec_t cp_fec2;
-#define cp_fec1 cp_fec /* consistency macro */
-
- /* Dual Ported RAM follows.
- * There are many different formats for this memory area
- * depending upon the devices used and options chosen.
- * Some processors don't have all of it populated.
- */
- u_char cp_dpmem[0x1C00]; /* BD / Data / ucode */
-
- /* Parameter RAM */
- union {
- u_char cp_dparam[0x400];
- u16 cp_dparam16[0x200];
- };
-} cpm8xx_t;
-
-/* Internal memory map.
-*/
-typedef struct immap {
- sysconf8xx_t im_siu_conf; /* SIU Configuration */
- pcmconf8xx_t im_pcmcia; /* PCMCIA Configuration */
- memctl8xx_t im_memctl; /* Memory Controller */
- sit8xx_t im_sit; /* System integration timers */
- car8xx_t im_clkrst; /* Clocks and reset */
- sitk8xx_t im_sitk; /* Sys int timer keys */
- cark8xx_t im_clkrstk; /* Clocks and reset keys */
- vid823_t im_vid; /* Video (823 only) */
- lcd823_t im_lcd; /* LCD (823 only) */
- i2c8xx_t im_i2c; /* I2C control/status */
- sdma8xx_t im_sdma; /* SDMA control/status */
- cpic8xx_t im_cpic; /* CPM Interrupt Controller */
- iop8xx_t im_ioport; /* IO Port control/status */
- cpmtimer8xx_t im_cpmtimer; /* CPM timers */
- cpm8xx_t im_cpm; /* Communication processor */
-} immap_t;
-
-#endif /* __IMMAP_8XX__ */
diff --git a/arch/powerpc/include/asm/cache.h b/arch/powerpc/include/asm/cache.h
index d3a83910b6fce2c6449d30fa040f4b7c596686b2..20c52fcddcff5a6bd239b9f1058c9760cb107380 100644
--- a/arch/powerpc/include/asm/cache.h
+++ b/arch/powerpc/include/asm/cache.h
@@ -7,9 +7,7 @@
#include <asm/processor.h>
/* bytes per L1 cache line */
-#if defined(CONFIG_8xx)
-#define L1_CACHE_SHIFT 4
-#elif defined(CONFIG_PPC64BRIDGE)
+#if defined(CONFIG_PPC64BRIDGE)
#define L1_CACHE_SHIFT 7
#elif defined(CONFIG_E500MC)
#define L1_CACHE_SHIFT 6
@@ -72,41 +70,4 @@ void disable_cpc_sram(void);
#define L2CACHE_NONE 0x03 /* NONE */
#define L2CACHE_PARITY 0x08 /* Mask for L2 Cache Parity Protected bit */
-#ifdef CONFIG_8xx
-/* Cache control on the MPC8xx is provided through some additional
- * special purpose registers.
- */
-#define IC_CST 560 /* Instruction cache control/status */
-#define IC_ADR 561 /* Address needed for some commands */
-#define IC_DAT 562 /* Read-only data register */
-#define DC_CST 568 /* Data cache control/status */
-#define DC_ADR 569 /* Address needed for some commands */
-#define DC_DAT 570 /* Read-only data register */
-
-/* Commands. Only the first few are available to the instruction cache.
-*/
-#define IDC_ENABLE 0x02000000 /* Cache enable */
-#define IDC_DISABLE 0x04000000 /* Cache disable */
-#define IDC_LDLCK 0x06000000 /* Load and lock */
-#define IDC_UNLINE 0x08000000 /* Unlock line */
-#define IDC_UNALL 0x0a000000 /* Unlock all */
-#define IDC_INVALL 0x0c000000 /* Invalidate all */
-
-#define DC_FLINE 0x0e000000 /* Flush data cache line */
-#define DC_SFWT 0x01000000 /* Set forced writethrough mode */
-#define DC_CFWT 0x03000000 /* Clear forced writethrough mode */
-#define DC_SLES 0x05000000 /* Set little endian swap mode */
-#define DC_CLES 0x07000000 /* Clear little endian swap mode */
-
-/* Status.
-*/
-#define IDC_ENABLED 0x80000000 /* Cache is enabled */
-#define IDC_CERR1 0x00200000 /* Cache error 1 */
-#define IDC_CERR2 0x00100000 /* Cache error 2 */
-#define IDC_CERR3 0x00080000 /* Cache error 3 */
-
-#define DC_DFWT 0x40000000 /* Data cache is forced write through */
-#define DC_LES 0x20000000 /* Caches are little endian mode */
-#endif /* CONFIG_8xx */
-
#endif
diff --git a/arch/powerpc/include/asm/global_data.h b/arch/powerpc/include/asm/global_data.h
index 3943d0e92b9e4f01829796c107bfd2abb7290042..cdf4be2c76d2c4f5120861f60ad05832c565b4ed 100644
--- a/arch/powerpc/include/asm/global_data.h
+++ b/arch/powerpc/include/asm/global_data.h
@@ -19,9 +19,6 @@ struct arch_global_data {
u8 sdhc_adapter;
#endif
#endif
-#if defined(CONFIG_8xx)
- unsigned long brg_clk;
-#endif
#if defined(CONFIG_CPM2)
/* There are many clocks on the MPC8260 - see page 9-5 */
unsigned long vco_out;
diff --git a/arch/powerpc/include/asm/iopin_8xx.h b/arch/powerpc/include/asm/iopin_8xx.h
deleted file mode 100644
index 8db0fa2a1c615916c276b9c339a9fc509eef90b3..0000000000000000000000000000000000000000
--- a/arch/powerpc/include/asm/iopin_8xx.h
+++ /dev/null
@@ -1,379 +0,0 @@
-/*
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * MPC8xx I/O port pin manipulation functions
- * Roughly based on iopin_8260.h
- */
-
-#ifndef _ASM_IOPIN_8XX_H_
-#define _ASM_IOPIN_8XX_H_
-
-#include <linux/types.h>
-#include <asm/8xx_immap.h>
-
-#ifdef __KERNEL__
-
-typedef struct {
- u_char port:2; /* port number (A=0, B=1, C=2, D=3) */
- u_char pin:5; /* port pin (0-31) */
- u_char flag:1; /* for whatever */
-} iopin_t;
-
-#define IOPIN_PORTA 0
-#define IOPIN_PORTB 1
-#define IOPIN_PORTC 2
-#define IOPIN_PORTD 3
-
-static __inline__ void
-iopin_set_high(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padat;
- *datp |= (1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat;
- *datp |= (1 << (31 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat;
- *datp |= (1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat;
- *datp |= (1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ void
-iopin_set_low(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padat;
- *datp &= ~(1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat;
- *datp &= ~(1 << (31 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat;
- *datp &= ~(1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat;
- *datp &= ~(1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ uint
-iopin_is_high(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padat;
- return (*datp >> (15 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat;
- return (*datp >> (31 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat;
- return (*datp >> (15 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat;
- return (*datp >> (15 - iopin->pin)) & 1;
- }
- return 0;
-}
-
-static __inline__ uint
-iopin_is_low(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padat;
- return ((*datp >> (15 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat;
- return ((*datp >> (31 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat;
- return ((*datp >> (15 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *datp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat;
- return ((*datp >> (15 - iopin->pin)) & 1) ^ 1;
- }
- return 0;
-}
-
-static __inline__ void
-iopin_set_out(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padir;
- *dirp |= (1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdir;
- *dirp |= (1 << (31 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdir;
- *dirp |= (1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddir;
- *dirp |= (1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ void
-iopin_set_in(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padir;
- *dirp &= ~(1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdir;
- *dirp &= ~(1 << (31 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdir;
- *dirp &= ~(1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddir;
- *dirp &= ~(1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ uint
-iopin_is_out(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padir;
- return (*dirp >> (15 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdir;
- return (*dirp >> (31 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdir;
- return (*dirp >> (15 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddir;
- return (*dirp >> (15 - iopin->pin)) & 1;
- }
- return 0;
-}
-
-static __inline__ uint
-iopin_is_in(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padir;
- return ((*dirp >> (15 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdir;
- return ((*dirp >> (31 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdir;
- return ((*dirp >> (15 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *dirp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddir;
- return ((*dirp >> (15 - iopin->pin)) & 1) ^ 1;
- }
- return 0;
-}
-
-static __inline__ void
-iopin_set_odr(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_paodr;
- *odrp |= (1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbodr;
- *odrp |= (1 << (31 - iopin->pin));
- }
-}
-
-static __inline__ void
-iopin_set_act(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_paodr;
- *odrp &= ~(1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbodr;
- *odrp &= ~(1 << (31 - iopin->pin));
- }
-}
-
-static __inline__ uint
-iopin_is_odr(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_paodr;
- return (*odrp >> (15 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbodr;
- return (*odrp >> (31 - iopin->pin)) & 1;
- }
- return 0;
-}
-
-static __inline__ uint
-iopin_is_act(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_paodr;
- return ((*odrp >> (15 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile ushort *odrp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbodr;
- return ((*odrp >> (31 - iopin->pin)) & 1) ^ 1;
- }
- return 0;
-}
-
-static __inline__ void
-iopin_set_ded(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_papar;
- *parp |= (1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbpar;
- *parp |= (1 << (31 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcpar;
- *parp |= (1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pdpar;
- *parp |= (1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ void
-iopin_set_gen(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_papar;
- *parp &= ~(1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbpar;
- *parp &= ~(1 << (31 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcpar;
- *parp &= ~(1 << (15 - iopin->pin));
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pdpar;
- *parp &= ~(1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ uint
-iopin_is_ded(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_papar;
- return (*parp >> (15 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbpar;
- return (*parp >> (31 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcpar;
- return (*parp >> (15 - iopin->pin)) & 1;
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pdpar;
- return (*parp >> (15 - iopin->pin)) & 1;
- }
- return 0;
-}
-
-static __inline__ uint
-iopin_is_gen(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTA) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_papar;
- return ((*parp >> (15 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTB) {
- volatile uint *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbpar;
- return ((*parp >> (31 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTC) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcpar;
- return ((*parp >> (15 - iopin->pin)) & 1) ^ 1;
- } else if (iopin->port == IOPIN_PORTD) {
- volatile ushort *parp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pdpar;
- return ((*parp >> (15 - iopin->pin)) & 1) ^ 1;
- }
- return 0;
-}
-
-static __inline__ void
-iopin_set_opt2(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *sorp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcso;
- *sorp |= (1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ void
-iopin_set_opt1(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *sorp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcso;
- *sorp &= ~(1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ uint
-iopin_is_opt2(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *sorp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcso;
- return (*sorp >> (15 - iopin->pin)) & 1;
- }
- return 0;
-}
-
-static __inline__ uint
-iopin_is_opt1(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *sorp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcso;
- return ((*sorp >> (15 - iopin->pin)) & 1) ^ 1;
- }
- return 0;
-}
-
-static __inline__ void
-iopin_set_falledge(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *intp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcint;
- *intp |= (1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ void
-iopin_set_anyedge(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *intp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcint;
- *intp &= ~(1 << (15 - iopin->pin));
- }
-}
-
-static __inline__ uint
-iopin_is_falledge(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *intp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcint;
- return (*intp >> (15 - iopin->pin)) & 1;
- }
- return 0;
-}
-
-static __inline__ uint
-iopin_is_anyedge(iopin_t *iopin)
-{
- if (iopin->port == IOPIN_PORTC) {
- volatile ushort *intp = &((immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcint;
- return ((*intp >> (15 - iopin->pin)) & 1) ^ 1;
- }
- return 0;
-}
-
-#endif /* __KERNEL__ */
-
-#endif /* _ASM_IOPIN_8XX_H_ */
diff --git a/arch/powerpc/include/asm/ppc.h b/arch/powerpc/include/asm/ppc.h
index 4e1c5965e42cedd66118c7828e391d762220c35c..8abe727bcaa3ff4f6412c21363e0fa724f3945a1 100644
--- a/arch/powerpc/include/asm/ppc.h
+++ b/arch/powerpc/include/asm/ppc.h
@@ -13,19 +13,7 @@
#ifndef __ASSEMBLY__
-#if defined(CONFIG_8xx)
-#include <asm/8xx_immap.h>
-#if defined(CONFIG_MPC859) || defined(CONFIG_MPC859T) || \
- defined(CONFIG_MPC866) || defined(CONFIG_MPC866P)
-# define CONFIG_MPC866_FAMILY 1
-#elif defined(CONFIG_MPC885)
-# define CONFIG_MPC885_FAMILY 1
-#endif
-#if defined(CONFIG_MPC860) || defined(CONFIG_MPC860T) || \
- defined(CONFIG_MPC866_FAMILY) || defined(CONFIG_MPC885_FAMILY)
-# define CONFIG_MPC86x 1
-#endif
-#elif defined(CONFIG_5xx)
+#if defined(CONFIG_5xx)
#include <asm/5xx_immap.h>
#elif defined(CONFIG_MPC5xxx)
#include <mpc5xxx.h>
@@ -62,29 +50,7 @@
#include <asm/arch/immap_lsch2.h>
#endif
-/*
- * enable common handling for all TQM8xxL/M boards:
- * - CONFIG_TQM8xxM will be defined for all TQM8xxM boards
- * - CONFIG_TQM8xxL will be defined for all TQM8xxL _and_ TQM8xxM boards
- * and for the TQM885D board
- */
-#if defined(CONFIG_TQM823M) || defined(CONFIG_TQM850M) || \
- defined(CONFIG_TQM855M) || defined(CONFIG_TQM860M) || \
- defined(CONFIG_TQM862M) || defined(CONFIG_TQM866M)
-# ifndef CONFIG_TQM8xxM
-# define CONFIG_TQM8xxM
-# endif
-#endif
-#if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L) || \
- defined(CONFIG_TQM855L) || defined(CONFIG_TQM860L) || \
- defined(CONFIG_TQM862L) || defined(CONFIG_TQM8xxM) || \
- defined(CONFIG_TQM885D)
-# ifndef CONFIG_TQM8xxL
-# define CONFIG_TQM8xxL
-# endif
-#endif
-
-#if defined(CONFIG_5xx) || defined(CONFIG_8xx)
+#if defined(CONFIG_5xx)
uint get_immr(uint);
#endif
#if defined(CONFIG_MPC5xxx)
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index fd38da9fe5e34205fe906992e7e7fad2e1672178..aaabae040136a991e9719e939a5ad3127f0eb31f 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -1361,10 +1361,7 @@ int prt_8260_clks(void);
#endif /* ndef ASSEMBLY*/
#ifdef CONFIG_MACH_SPECIFIC
-#if defined(CONFIG_8xx)
-#define _machine _MACH_8xx
-#define have_of 0
-#elif defined(CONFIG_WALNUT)
+#if defined(CONFIG_WALNUT)
#define _machine _MACH_walnut
#define have_of 0
#elif defined(CONFIG_MPC8260)
diff --git a/arch/powerpc/include/asm/status_led.h b/arch/powerpc/include/asm/status_led.h
index 1ae1b17e2d1b9024c30938eca1b673bc8b1fed55..c151b5406086b1a993cd471d950460310671ceb0 100644
--- a/arch/powerpc/include/asm/status_led.h
+++ b/arch/powerpc/include/asm/status_led.h
@@ -9,9 +9,7 @@
/* if not overridden */
#ifndef CONFIG_LED_STATUS_BOARD_SPECIFIC
-# if defined(CONFIG_8xx)
-# include <mpc8xx.h>
-# elif defined(CONFIG_MPC8260)
+# if defined(CONFIG_MPC8260)
# include <mpc8260.h>
# elif defined(CONFIG_5xx)
# include <mpc5xx.h>
diff --git a/arch/powerpc/lib/Makefile b/arch/powerpc/lib/Makefile
index e09bd9a88a2b04f6a29cee2d2f6d5ccb64200035..5e55385e01446b891e185128164ef484dc5609ca 100644
--- a/arch/powerpc/lib/Makefile
+++ b/arch/powerpc/lib/Makefile
@@ -36,7 +36,6 @@ obj-y += extable.o
obj-$(CONFIG_CMD_IMMAP) += immap.o
obj-y += interrupts.o
obj-$(CONFIG_CMD_KGDB) += kgdb.o
-obj-$(CONFIG_IDE) += ide.o
obj-y += stack.o
obj-y += time.o
diff --git a/arch/powerpc/lib/ide.c b/arch/powerpc/lib/ide.c
deleted file mode 100644
index b4ead726a6e3f4f283d9fea1a83bdcc8195eaa21..0000000000000000000000000000000000000000
--- a/arch/powerpc/lib/ide.c
+++ /dev/null
@@ -1,184 +0,0 @@
-/*
- * (C) Copyright 2000-2011
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* Code taken from cmd_ide.c */
-#include <common.h>
-#include <ata.h>
-#include "ide.h"
-
-#ifdef CONFIG_IDE_8xx_DIRECT
-#include <mpc8xx.h>
-#include <pcmcia.h>
-DECLARE_GLOBAL_DATA_PTR;
-
-/* Timings for IDE Interface
- *
- * SETUP / LENGTH / HOLD - cycles valid for 50 MHz clk
- * 70 165 30 PIO-Mode 0, [ns]
- * 4 9 2 [Cycles]
- * 50 125 20 PIO-Mode 1, [ns]
- * 3 7 2 [Cycles]
- * 30 100 15 PIO-Mode 2, [ns]
- * 2 6 1 [Cycles]
- * 30 80 10 PIO-Mode 3, [ns]
- * 2 5 1 [Cycles]
- * 25 70 10 PIO-Mode 4, [ns]
- * 2 4 1 [Cycles]
- */
-
-static const pio_config_t pio_config_ns[IDE_MAX_PIO_MODE+1] = {
- /* Setup Length Hold */
- { 70, 165, 30 }, /* PIO-Mode 0, [ns] */
- { 50, 125, 20 }, /* PIO-Mode 1, [ns] */
- { 30, 101, 15 }, /* PIO-Mode 2, [ns] */
- { 30, 80, 10 }, /* PIO-Mode 3, [ns] */
- { 25, 70, 10 }, /* PIO-Mode 4, [ns] */
-};
-
-static pio_config_t pio_config_clk[IDE_MAX_PIO_MODE+1];
-
-#ifndef CONFIG_SYS_PIO_MODE
-#define CONFIG_SYS_PIO_MODE 0 /* use a relaxed default */
-#endif
-static int pio_mode = CONFIG_SYS_PIO_MODE;
-
-/* Make clock cycles and always round up */
-
-#define PCMCIA_MK_CLKS(t, T) (((t) * (T) + 999U) / 1000U)
-
-static void set_pcmcia_timing(int pmode)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile pcmconf8xx_t *pcmp = &(immr->im_pcmcia);
- ulong timings;
-
- debug("Set timing for PIO Mode %d\n", pmode);
-
- timings = PCMCIA_SHT(pio_config_clk[pmode].t_hold)
- | PCMCIA_SST(pio_config_clk[pmode].t_setup)
- | PCMCIA_SL(pio_config_clk[pmode].t_length);
-
- /*
- * IDE 0
- */
- pcmp->pcmc_pbr0 = CONFIG_SYS_PCMCIA_PBR0;
-#if (CONFIG_SYS_PCMCIA_POR0 != 0)
- pcmp->pcmc_por0 = CONFIG_SYS_PCMCIA_POR0 | timings;
-#else
- pcmp->pcmc_por0 = CONFIG_SYS_PCMCIA_POR0;
-#endif
- debug("PBR0: %08x POR0: %08x\n", pcmp->pcmc_pbr0, pcmp->pcmc_por0);
-
- pcmp->pcmc_pbr1 = CONFIG_SYS_PCMCIA_PBR1;
-#if (CONFIG_SYS_PCMCIA_POR1 != 0)
- pcmp->pcmc_por1 = CONFIG_SYS_PCMCIA_POR1 | timings;
-#else
- pcmp->pcmc_por1 = CONFIG_SYS_PCMCIA_POR1;
-#endif
- debug("PBR1: %08x POR1: %08x\n", pcmp->pcmc_pbr1, pcmp->pcmc_por1);
-
- pcmp->pcmc_pbr2 = CONFIG_SYS_PCMCIA_PBR2;
-#if (CONFIG_SYS_PCMCIA_POR2 != 0)
- pcmp->pcmc_por2 = CONFIG_SYS_PCMCIA_POR2 | timings;
-#else
- pcmp->pcmc_por2 = CONFIG_SYS_PCMCIA_POR2;
-#endif
- debug("PBR2: %08x POR2: %08x\n", pcmp->pcmc_pbr2, pcmp->pcmc_por2);
-
- pcmp->pcmc_pbr3 = CONFIG_SYS_PCMCIA_PBR3;
-#if (CONFIG_SYS_PCMCIA_POR3 != 0)
- pcmp->pcmc_por3 = CONFIG_SYS_PCMCIA_POR3 | timings;
-#else
- pcmp->pcmc_por3 = CONFIG_SYS_PCMCIA_POR3;
-#endif
- debug("PBR3: %08x POR3: %08x\n", pcmp->pcmc_pbr3, pcmp->pcmc_por3);
-
- /*
- * IDE 1
- */
- pcmp->pcmc_pbr4 = CONFIG_SYS_PCMCIA_PBR4;
-#if (CONFIG_SYS_PCMCIA_POR4 != 0)
- pcmp->pcmc_por4 = CONFIG_SYS_PCMCIA_POR4 | timings;
-#else
- pcmp->pcmc_por4 = CONFIG_SYS_PCMCIA_POR4;
-#endif
- debug("PBR4: %08x POR4: %08x\n", pcmp->pcmc_pbr4, pcmp->pcmc_por4);
-
- pcmp->pcmc_pbr5 = CONFIG_SYS_PCMCIA_PBR5;
-#if (CONFIG_SYS_PCMCIA_POR5 != 0)
- pcmp->pcmc_por5 = CONFIG_SYS_PCMCIA_POR5 | timings;
-#else
- pcmp->pcmc_por5 = CONFIG_SYS_PCMCIA_POR5;
-#endif
- debug("PBR5: %08x POR5: %08x\n", pcmp->pcmc_pbr5, pcmp->pcmc_por5);
-
- pcmp->pcmc_pbr6 = CONFIG_SYS_PCMCIA_PBR6;
-#if (CONFIG_SYS_PCMCIA_POR6 != 0)
- pcmp->pcmc_por6 = CONFIG_SYS_PCMCIA_POR6 | timings;
-#else
- pcmp->pcmc_por6 = CONFIG_SYS_PCMCIA_POR6;
-#endif
- debug("PBR6: %08x POR6: %08x\n", pcmp->pcmc_pbr6, pcmp->pcmc_por6);
-
- pcmp->pcmc_pbr7 = CONFIG_SYS_PCMCIA_PBR7;
-#if (CONFIG_SYS_PCMCIA_POR7 != 0)
- pcmp->pcmc_por7 = CONFIG_SYS_PCMCIA_POR7 | timings;
-#else
- pcmp->pcmc_por7 = CONFIG_SYS_PCMCIA_POR7;
-#endif
- debug("PBR7: %08x POR7: %08x\n", pcmp->pcmc_pbr7, pcmp->pcmc_por7);
-
-}
-
-int ide_preinit(void)
-{
- int i;
- /* Initialize PIO timing tables */
- for (i = 0; i <= IDE_MAX_PIO_MODE; ++i) {
- pio_config_clk[i].t_setup =
- PCMCIA_MK_CLKS(pio_config_ns[i].t_setup, gd->bus_clk);
- pio_config_clk[i].t_length =
- PCMCIA_MK_CLKS(pio_config_ns[i].t_length, gd->bus_clk);
- pio_config_clk[i].t_hold =
- PCMCIA_MK_CLKS(pio_config_ns[i].t_hold, gd->bus_clk);
- debug("PIO Mode %d: setup=%2d ns/%d clk" " len=%3d ns/%d clk"
- " hold=%2d ns/%d clk\n", i, pio_config_ns[i].t_setup,
- pio_config_clk[i].t_setup, pio_config_ns[i].t_length,
- pio_config_clk[i].t_length, pio_config_ns[i].t_hold,
- pio_config_clk[i].t_hold);
- }
-
- return 0;
-}
-
-int ide_init_postreset(void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile pcmconf8xx_t *pcmp = &(immr->im_pcmcia);
-
- /* PCMCIA / IDE initialization for common mem space */
- pcmp->pcmc_pgcrb = 0;
-
- /* start in PIO mode 0 - most relaxed timings */
- pio_mode = 0;
- set_pcmcia_timing(pio_mode);
- return 0;
-}
-#endif /* CONFIG_IDE_8xx_DIRECT */
-
-#ifdef CONFIG_IDE_8xx_PCCARD
-int ide_preinit(void)
-{
- ide_devices_found = 0;
- /* initialize the PCMCIA IDE adapter card */
- pcmcia_on();
- if (!ide_devices_found)
- return 1;
- udelay(1000000);/* 1 s */
- return 0;
-}
-#endif
diff --git a/arch/powerpc/lib/ide.h b/arch/powerpc/lib/ide.h
deleted file mode 100644
index e0b2e6197b977e7d51d6ba64efd4cf4afe4c5885..0000000000000000000000000000000000000000
--- a/arch/powerpc/lib/ide.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/*
- * (C) Copyright 2012
- * Pavel Herrmann <morpheus.ibis@gmail.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _MPC8XX_IDE_H_
-#define _MPC8XX_IDE_H_ 1
-
-#ifdef CONFIG_IDE_8xx_PCCARD
-int pcmcia_on(void);
-extern int ide_devices_found;
-#endif
-#endif
diff --git a/arch/powerpc/lib/immap.c b/arch/powerpc/lib/immap.c
index 1414f9ad55d0e7a242db018e2bf5f83d9cf4e519..85527a1b8fc3dea604282dd4de5a83fcb6d5b64a 100644
--- a/arch/powerpc/lib/immap.c
+++ b/arch/powerpc/lib/immap.c
@@ -12,17 +12,11 @@
#include <common.h>
#include <command.h>
-#if defined(CONFIG_8xx) || defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
-#if defined(CONFIG_8xx)
-#include <asm/8xx_immap.h>
-#include <commproc.h>
-#include <asm/iopin_8xx.h>
-#elif defined(CONFIG_MPC8260)
#include <asm/immap_8260.h>
#include <asm/cpm_8260.h>
#include <asm/iopin_8260.h>
-#endif
DECLARE_GLOBAL_DATA_PTR;
@@ -38,19 +32,12 @@ do_siuinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#if defined(CONFIG_8xx)
- volatile sysconf8xx_t *sc = &immap->im_siu_conf;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
volatile sysconf8260_t *sc = &immap->im_siu_conf;
#endif
printf ("SIUMCR= %08x SYPCR = %08x\n", sc->sc_siumcr, sc->sc_sypcr);
-#if defined(CONFIG_8xx)
- printf ("SWT = %08x\n", sc->sc_swt);
- printf ("SIPEND= %08x SIMASK= %08x\n", sc->sc_sipend, sc->sc_simask);
- printf ("SIEL = %08x SIVEC = %08x\n", sc->sc_siel, sc->sc_sivec);
- printf ("TESR = %08x SDCR = %08x\n", sc->sc_tesr, sc->sc_sdcr);
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
printf ("BCR = %08x\n", sc->sc_bcr);
printf ("P_ACR = %02x P_ALRH= %08x P_ALRL= %08x\n",
sc->sc_ppc_acr, sc->sc_ppc_alrh, sc->sc_ppc_alrl);
@@ -69,10 +56,7 @@ do_memcinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#if defined(CONFIG_8xx)
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- int nbanks = 8;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
volatile memctl8260_t *memctl = &immap->im_memctl;
int nbanks = 12;
#endif
@@ -90,16 +74,12 @@ do_memcinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
}
printf ("MAR = %08x", memctl->memc_mar);
-#if defined(CONFIG_8xx)
- printf (" MCR = %08x\n", memctl->memc_mcr);
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
putc ('\n');
#endif
printf ("MAMR = %08x MBMR = %08x",
memctl->memc_mamr, memctl->memc_mbmr);
-#if defined(CONFIG_8xx)
- printf ("\nMSTAT = %04x\n", memctl->memc_mstat);
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
printf (" MCMR = %08x\n", memctl->memc_mcmr);
#endif
printf ("MPTPR = %04x MDR = %08x\n",
@@ -137,17 +117,11 @@ do_carinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#if defined(CONFIG_8xx)
- volatile car8xx_t *car = &immap->im_clkrst;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
volatile car8260_t *car = &immap->im_clkrst;
#endif
-#if defined(CONFIG_8xx)
- printf ("SCCR = %08x\n", car->car_sccr);
- printf ("PLPRCR= %08x\n", car->car_plprcr);
- printf ("RSR = %08x\n", car->car_rsr);
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
printf ("SCCR = %08x\n", car->car_sccr);
printf ("SCMR = %08x\n", car->car_scmr);
printf ("RSR = %08x\n", car->car_rsr);
@@ -200,14 +174,7 @@ static void binary (char *label, uint value, int nbits)
putc ('\n');
}
-#if defined(CONFIG_8xx)
-#define PA_NBITS 16
-#define PA_NB_ODR 8
-#define PB_NBITS 18
-#define PB_NB_ODR 16
-#define PC_NBITS 12
-#define PD_NBITS 13
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
#define PA_NBITS 32
#define PA_NB_ODR 32
#define PB_NBITS 28
@@ -221,10 +188,7 @@ do_iopinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#if defined(CONFIG_8xx)
- volatile iop8xx_t *iop = &immap->im_ioport;
- volatile ushort *l, *r;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
volatile iop8260_t *iop = &immap->im_ioport;
volatile uint *l, *r;
#endif
@@ -237,10 +201,7 @@ do_iopinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
* Ports A & B
*/
-#if defined(CONFIG_8xx)
- l = &iop->iop_padir;
- R = &immap->im_cpm.cp_pbdir;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
l = &iop->iop_pdira;
R = &iop->iop_pdirb;
#endif
@@ -263,10 +224,7 @@ do_iopinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
* Ports C & D
*/
-#if defined(CONFIG_8xx)
- l = &iop->iop_pcdir;
- r = &iop->iop_pddir;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
l = &iop->iop_pdirc;
r = &iop->iop_pdird;
#endif
@@ -274,11 +232,7 @@ do_iopinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
binary ("PD_DIR", *r++, PD_NBITS);
binary ("PC_PAR", *l++, PC_NBITS);
binary ("PD_PAR", *r++, PD_NBITS);
-#if defined(CONFIG_8xx)
- binary ("PC_SO ", *l++, PC_NBITS);
- binary (" ", 0, 0);
- r++;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
binary ("PC_SOR", *l++, PC_NBITS);
binary ("PD_SOR", *r++, PD_NBITS);
binary ("PC_ODR", *l++, PC_NBITS);
@@ -286,9 +240,6 @@ do_iopinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
#endif
binary ("PC_DAT", *l++, PC_NBITS);
binary ("PD_DAT", *r++, PD_NBITS);
-#if defined(CONFIG_8xx)
- binary ("PC_INT", *l++, PC_NBITS);
-#endif
header ();
return 0;
@@ -313,9 +264,6 @@ do_iopset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
SOR,
ODR,
DAT,
-#if defined(CONFIG_8xx)
- INT
-#endif
} cmd = DAT;
if (argc != 5) {
@@ -350,11 +298,6 @@ do_iopset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
case 's':
cmd = SOR;
break;
-#if defined(CONFIG_8xx)
- case 'i':
- cmd = INT;
- break;
-#endif
default:
printf ("iopset: unknown command %s\n", argv[3]);
rcode = 1;
@@ -400,14 +343,6 @@ do_iopset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
else
iopin_set_low (&iopin);
break;
-#if defined(CONFIG_8xx)
- case INT:
- if (value)
- iopin_set_falledge (&iopin);
- else
- iopin_set_anyedge (&iopin);
- break;
-#endif
}
}
@@ -434,9 +369,7 @@ static void prbrg (int n, uint val)
uint cd = (val & CPM_BRG_CD_MASK) >> 1;
uint div16 = (val & CPM_BRG_DIV16) != 0;
-#if defined(CONFIG_8xx)
- ulong clock = gd->cpu_clk;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
ulong clock = gd->arch.brg_clk;
#endif
@@ -486,10 +419,7 @@ do_brginfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#if defined(CONFIG_8xx)
- volatile cpm8xx_t *cp = &immap->im_cpm;
- volatile uint *p = &cp->cp_brgc1;
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
volatile uint *p = &immap->im_brgc1;
#endif
int i = 1;
@@ -510,11 +440,7 @@ do_i2cinfo (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#if defined(CONFIG_8xx)
- volatile i2c8xx_t *i2c = &immap->im_i2c;
- volatile cpm8xx_t *cp = &immap->im_cpm;
- volatile iic_t *iip = (iic_t *) & cp->cp_dparam[PROFF_IIC];
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
volatile i2c8260_t *i2c = &immap->im_i2c;
volatile iic_t *iip;
uint dpaddr;
diff --git a/arch/powerpc/lib/time.c b/arch/powerpc/lib/time.c
index de5f0be66dce29803e930854423e2634c3fcd1d4..c1a0a69a51eebb70bd4511c5bca366d34bd992e6 100644
--- a/arch/powerpc/lib/time.c
+++ b/arch/powerpc/lib/time.c
@@ -64,7 +64,7 @@ int timer_init(void)
{
unsigned long temp;
-#if defined(CONFIG_5xx) || defined(CONFIG_8xx)
+#if defined(CONFIG_5xx)
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
/* unlock */
@@ -75,7 +75,7 @@ int timer_init(void)
asm volatile("li %0,0 ; mttbu %0 ; mttbl %0;"
: "=&r"(temp) );
-#if defined(CONFIG_5xx) || defined(CONFIG_8xx)
+#if defined(CONFIG_5xx)
/* enable */
immap->im_sit.sit_tbscr |= TBSCR_TBE;
#endif
diff --git a/board/tqc/tqm8xx/Kconfig b/board/tqc/tqm8xx/Kconfig
deleted file mode 100644
index 857fedb8bec944e4718bf625c7257e9b40d6ffe7..0000000000000000000000000000000000000000
--- a/board/tqc/tqm8xx/Kconfig
+++ /dev/null
@@ -1,155 +0,0 @@
-if TARGET_TQM823L
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM823L"
-
-endif
-
-if TARGET_TQM823M
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM823M"
-
-endif
-
-if TARGET_TQM850L
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM850L"
-
-endif
-
-if TARGET_TQM850M
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM850M"
-
-endif
-
-if TARGET_TQM855L
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM855L"
-
-endif
-
-if TARGET_TQM855M
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM855M"
-
-endif
-
-if TARGET_TQM860L
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM860L"
-
-endif
-
-if TARGET_TQM860M
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM860M"
-
-endif
-
-if TARGET_TQM862L
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM862L"
-
-endif
-
-if TARGET_TQM862M
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM862M"
-
-endif
-
-if TARGET_TQM866M
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM866M"
-
-endif
-
-if TARGET_TQM885D
-
-config SYS_BOARD
- default "tqm8xx"
-
-config SYS_VENDOR
- default "tqc"
-
-config SYS_CONFIG_NAME
- default "TQM885D"
-
-endif
diff --git a/board/tqc/tqm8xx/MAINTAINERS b/board/tqc/tqm8xx/MAINTAINERS
deleted file mode 100644
index f3ddc6a5304ab87c4e0d7aefecc890f89a2c9f63..0000000000000000000000000000000000000000
--- a/board/tqc/tqm8xx/MAINTAINERS
+++ /dev/null
@@ -1,31 +0,0 @@
-TQM8XX BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/tqc/tqm8xx/
-F: include/configs/TQM823L.h
-F: configs/TQM823L_defconfig
-F: configs/TQM823L_LCD_defconfig
-F: include/configs/TQM823M.h
-F: configs/TQM823M_defconfig
-F: include/configs/TQM850L.h
-F: configs/TQM850L_defconfig
-F: include/configs/TQM850M.h
-F: configs/TQM850M_defconfig
-F: include/configs/TQM855L.h
-F: configs/TQM855L_defconfig
-F: include/configs/TQM855M.h
-F: configs/TQM855M_defconfig
-F: include/configs/TQM860L.h
-F: configs/TQM860L_defconfig
-F: include/configs/TQM860M.h
-F: configs/TQM860M_defconfig
-F: include/configs/TQM862L.h
-F: configs/TQM862L_defconfig
-F: include/configs/TQM862M.h
-F: configs/TQM862M_defconfig
-F: include/configs/TQM866M.h
-F: configs/TQM866M_defconfig
-F: include/configs/TQM885D.h
-F: configs/TQM885D_defconfig
-F: configs/TTTech_defconfig
-F: configs/wtk_defconfig
diff --git a/board/tqc/tqm8xx/Makefile b/board/tqc/tqm8xx/Makefile
deleted file mode 100644
index 2651a2f99f5668a29b3481bb37ec1eb1b782955b..0000000000000000000000000000000000000000
--- a/board/tqc/tqm8xx/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = tqm8xx.o load_sernum_ethaddr.o
diff --git a/board/tqc/tqm8xx/load_sernum_ethaddr.c b/board/tqc/tqm8xx/load_sernum_ethaddr.c
deleted file mode 100644
index 0070da1fb85db5219b1a69a7bf13c5be2722e18d..0000000000000000000000000000000000000000
--- a/board/tqc/tqm8xx/load_sernum_ethaddr.c
+++ /dev/null
@@ -1,89 +0,0 @@
-/*
- * (C) Copyright 2000, 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-/*-----------------------------------------------------------------------
- * Process Hardware Information Block:
- *
- * If we boot on a system fresh from factory, check if the Hardware
- * Information Block exists and save the information it contains.
- *
- * The TQM8xxL / TQM82xx Hardware Information Block is defined as
- * follows:
- * - located in first flash bank
- * - starts at offset 0x0003FFC0
- * - size 0x00000040
- *
- * Internal structure:
- * - sequence of ASCII character strings
- * - fields separated by a single space character (0x20)
- * - last field terminated by NUL character (0x00)
- * - remaining space filled with NUL characters (0x00)
- *
- * Fields in Hardware Information Block:
- * 1) Module Type
- * 2) Serial Number
- * 3) First MAC Address
- * 4) Number of additional MAC addresses
- */
-
-void load_sernum_ethaddr (void)
-{
- unsigned char *hwi;
- unsigned char serial [CONFIG_SYS_HWINFO_SIZE];
- unsigned char ethaddr[CONFIG_SYS_HWINFO_SIZE];
- unsigned short ih, is, ie, part;
-
- hwi = (unsigned char *)(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_HWINFO_OFFSET);
- ih = is = ie = 0;
-
- if (*((unsigned long *)hwi) != (unsigned long)CONFIG_SYS_HWINFO_MAGIC) {
- return;
- }
-
- part = 1;
-
- /* copy serial # / MAC address */
- while ((hwi[ih] != '\0') && (ih < CONFIG_SYS_HWINFO_SIZE)) {
- if (hwi[ih] < ' ' || hwi[ih] > '~') { /* ASCII strings! */
- return;
- }
- switch (part) {
- default: /* Copy serial # */
- if (hwi[ih] == ' ') {
- ++part;
- }
- serial[is++] = hwi[ih];
- break;
- case 3: /* Copy MAC address */
- if (hwi[ih] == ' ') {
- ++part;
- break;
- }
- ethaddr[ie++] = hwi[ih];
- if ((ie % 3) == 2)
- ethaddr[ie++] = ':';
- break;
- }
- ++ih;
- }
- serial[is] = '\0';
- if (ie && ethaddr[ie-1] == ':')
- --ie;
- ethaddr[ie] = '\0';
-
- /* set serial# and ethaddr if not yet defined */
- if (getenv("serial#") == NULL) {
- setenv ((char *)"serial#", (char *)serial);
- }
-
- if (getenv("ethaddr") == NULL) {
- setenv ((char *)"ethaddr", (char *)ethaddr);
- }
-}
diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c
deleted file mode 100644
index 58bd7fae47059a4f47dc2464e3d21632a4b04f2f..0000000000000000000000000000000000000000
--- a/board/tqc/tqm8xx/tqm8xx.c
+++ /dev/null
@@ -1,677 +0,0 @@
-/*
- * (C) Copyright 2000-2008
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <hwconfig.h>
-#include <mpc8xx.h>
-#ifdef CONFIG_PS2MULT
-#include <ps2mult.h>
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
-#include <libfdt.h>
-#endif
-
-extern flash_info_t flash_info[]; /* FLASH chips info */
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static long int dram_size (long int, long int *, long int);
-
-#define _NOT_USED_ 0xFFFFFFFF
-
-/* UPM initialization table for SDRAM: 40, 50, 66 MHz CLKOUT @ CAS latency 2, tWR=2 */
-const uint sdram_table[] =
-{
- /*
- * Single Read. (Offset 0 in UPMA RAM)
- */
- 0x1F0DFC04, 0xEEAFBC04, 0x11AF7C04, 0xEFBAFC00,
- 0x1FF5FC47, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPMA RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */
- /*
- * Burst Read. (Offset 8 in UPMA RAM)
- */
- 0x1F0DFC04, 0xEEAFBC04, 0x10AF7C04, 0xF0AFFC00,
- 0xF0AFFC00, 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPMA RAM)
- */
- 0x1F0DFC04, 0xEEABBC00, 0x11B77C04, 0xEFFAFC44,
- 0x1FF5FC47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPMA RAM)
- */
- 0x1F0DFC04, 0xEEABBC00, 0x10A77C00, 0xF0AFFC00,
- 0xF0AFFC00, 0xF0AFFC04, 0xE1BAFC44, 0x1FF5FC47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPMA RAM)
- */
- 0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC84, 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPMA RAM)
- */
- 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-/* ------------------------------------------------------------------------- */
-
-
-/*
- * Check Board Identity:
- *
- * Test TQ ID string (TQM8xx...)
- * If present, check for "L" type (no second DRAM bank),
- * otherwise "L" type is assumed as default.
- *
- * Set board_type to 'L' for "L" type, 'M' for "M" type, 0 else.
- */
-
-int checkboard (void)
-{
- char buf[64];
- int i;
- int l = getenv_f("serial#", buf, sizeof(buf));
-
- puts ("Board: ");
-
- if (l < 0 || strncmp(buf, "TQM8", 4)) {
- puts ("### No HW ID - assuming TQM8xxL\n");
- return (0);
- }
-
- if ((buf[6] == 'L')) { /* a TQM8xxL type */
- gd->board_type = 'L';
- }
-
- if ((buf[6] == 'M')) { /* a TQM8xxM type */
- gd->board_type = 'M';
- }
-
- if ((buf[6] == 'D')) { /* a TQM885D type */
- gd->board_type = 'D';
- }
-
- for (i = 0; i < l; ++i) {
- if (buf[i] == ' ')
- break;
- putc (buf[i]);
- }
-
- putc ('\n');
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-int dram_init(void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size8, size9, size10;
- long int size_b0 = 0;
- long int size_b1 = 0;
- int board_type = gd->board_type;
-
- upmconfig (UPMA, (uint *) sdram_table,
- sizeof (sdram_table) / sizeof (uint));
-
- /*
- * Preliminary prescaler for refresh (depends on number of
- * banks): This value is selected for four cycles every 62.4 us
- * with two SDRAM banks or four cycles every 31.2 us with one
- * bank. It will be adjusted after memory sizing.
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
-
- /*
- * The following value is used as an address (i.e. opcode) for
- * the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If
- * the port size is 32bit the SDRAM does NOT "see" the lower two
- * address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for
- * MICRON SDRAMs:
- * -> 0 00 010 0 010
- * | | | | +- Burst Length = 4
- * | | | +----- Burst Type = Sequential
- * | | +------- CAS Latency = 2
- * | +----------- Operating Mode = Standard
- * +-------------- Write Burst Mode = Programmed Burst Length
- */
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
- * preliminary addresses - these have to be modified after the
- * SDRAM size has been determined.
- */
- memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM;
- memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
-
-#ifndef CONFIG_CAN_DRIVER
- if ((board_type != 'L') &&
- (board_type != 'M') &&
- (board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */
- memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
- }
-#endif /* CONFIG_CAN_DRIVER */
-
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
-
- udelay (200);
-
- /* perform SDRAM initializsation sequence */
-
- memctl->memc_mcr = 0x80004105; /* SDRAM bank 0 */
- udelay (1);
- memctl->memc_mcr = 0x80004230; /* SDRAM bank 0 - execute twice */
- udelay (1);
-
-#ifndef CONFIG_CAN_DRIVER
- if ((board_type != 'L') &&
- (board_type != 'M') &&
- (board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */
- memctl->memc_mcr = 0x80006105; /* SDRAM bank 1 */
- udelay (1);
- memctl->memc_mcr = 0x80006230; /* SDRAM bank 1 - execute twice */
- udelay (1);
- }
-#endif /* CONFIG_CAN_DRIVER */
-
- memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
-
- udelay (1000);
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MAMR_8COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
- debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size8 >> 20);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
- debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size9 >> 20);
-
- udelay(1000);
-
-#if defined(CONFIG_SYS_MAMR_10COL)
- /*
- * try 10 column mode
- */
- size10 = dram_size (CONFIG_SYS_MAMR_10COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
- debug ("SDRAM Bank 0 in 10 column mode: %ld MB\n", size10 >> 20);
-#else
- size10 = 0;
-#endif /* CONFIG_SYS_MAMR_10COL */
-
- if ((size8 < size10) && (size9 < size10)) {
- size_b0 = size10;
- } else if ((size8 < size9) && (size10 < size9)) {
- size_b0 = size9;
- memctl->memc_mamr = CONFIG_SYS_MAMR_9COL;
- udelay (500);
- } else {
- size_b0 = size8;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
- udelay (500);
- }
- debug ("SDRAM Bank 0: %ld MB\n", size_b0 >> 20);
-
-#ifndef CONFIG_CAN_DRIVER
- if ((board_type != 'L') &&
- (board_type != 'M') &&
- (board_type != 'D') ) { /* only one SDRAM bank on L, M and D modules */
- /*
- * Check Bank 1 Memory Size
- * use current column settings
- * [9 column SDRAM may also be used in 8 column mode,
- * but then only half the real size will be used.]
- */
- size_b1 = dram_size (memctl->memc_mamr, (long int *)SDRAM_BASE3_PRELIM,
- SDRAM_MAX_SIZE);
- debug ("SDRAM Bank 1: %ld MB\n", size_b1 >> 20);
- } else {
- size_b1 = 0;
- }
-#endif /* CONFIG_CAN_DRIVER */
-
- udelay (1000);
-
- /*
- * Adjust refresh rate depending on SDRAM type, both banks
- * For types > 128 MBit leave it at the current (fast) rate
- */
- if ((size_b0 < 0x02000000) && (size_b1 < 0x02000000)) {
- /* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
- udelay (1000);
- }
-
- /*
- * Final mapping: map bigger bank first
- */
- if (size_b1 > size_b0) { /* SDRAM Bank 1 is bigger - map first */
-
- memctl->memc_or3 = ((-size_b1) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- if (size_b0 > 0) {
- /*
- * Position Bank 0 immediately above Bank 1
- */
- memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br2 = ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V)
- + size_b1;
- } else {
- unsigned long reg;
-
- /*
- * No bank 0
- *
- * invalidate bank
- */
- memctl->memc_br2 = 0;
-
- /* adjust refresh rate depending on SDRAM type, one bank */
- reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
- memctl->memc_mptpr = reg;
- }
-
- } else { /* SDRAM Bank 0 is bigger - map first */
-
- memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br2 =
- (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- if (size_b1 > 0) {
- /*
- * Position Bank 1 immediately above Bank 0
- */
- memctl->memc_or3 =
- ((-size_b1) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br3 =
- ((CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V)
- + size_b0;
- } else {
- unsigned long reg;
-
-#ifndef CONFIG_CAN_DRIVER
- /*
- * No bank 1
- *
- * invalidate bank
- */
- memctl->memc_br3 = 0;
-#endif /* CONFIG_CAN_DRIVER */
-
- /* adjust refresh rate depending on SDRAM type, one bank */
- reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
- memctl->memc_mptpr = reg;
- }
- }
-
- udelay (10000);
-
-#ifdef CONFIG_CAN_DRIVER
- /* UPM initialization for CAN @ CLKOUT <= 66 MHz */
-
- /* Initialize OR3 / BR3 */
- memctl->memc_or3 = CONFIG_SYS_OR3_CAN;
- memctl->memc_br3 = CONFIG_SYS_BR3_CAN;
-
- /* Initialize MBMR */
- memctl->memc_mbmr = MBMR_GPL_B4DIS; /* GPL_B4 ouput line Disable */
-
- /* Initialize UPMB for CAN: single read */
- memctl->memc_mdr = 0xFFFFCC04;
- memctl->memc_mcr = 0x0100 | UPMB;
-
- memctl->memc_mdr = 0x0FFFD004;
- memctl->memc_mcr = 0x0101 | UPMB;
-
- memctl->memc_mdr = 0x0FFFC000;
- memctl->memc_mcr = 0x0102 | UPMB;
-
- memctl->memc_mdr = 0x3FFFC004;
- memctl->memc_mcr = 0x0103 | UPMB;
-
- memctl->memc_mdr = 0xFFFFDC07;
- memctl->memc_mcr = 0x0104 | UPMB;
-
- /* Initialize UPMB for CAN: single write */
- memctl->memc_mdr = 0xFFFCCC04;
- memctl->memc_mcr = 0x0118 | UPMB;
-
- memctl->memc_mdr = 0xCFFCDC04;
- memctl->memc_mcr = 0x0119 | UPMB;
-
- memctl->memc_mdr = 0x3FFCC000;
- memctl->memc_mcr = 0x011A | UPMB;
-
- memctl->memc_mdr = 0xFFFCC004;
- memctl->memc_mcr = 0x011B | UPMB;
-
- memctl->memc_mdr = 0xFFFDC405;
- memctl->memc_mcr = 0x011C | UPMB;
-#endif /* CONFIG_CAN_DRIVER */
-
-#ifdef CONFIG_ISP1362_USB
- /* Initialize OR5 / BR5 */
- memctl->memc_or5 = CONFIG_SYS_OR5_ISP1362;
- memctl->memc_br5 = CONFIG_SYS_BR5_ISP1362;
-#endif /* CONFIG_ISP1362_USB */
- gd->ram_size = size_b0 + size_b1;
-
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value, long int *base, long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mamr = mamr_value;
-
- return (get_ram_size(base, maxsize));
-}
-
-/* ------------------------------------------------------------------------- */
-
-#ifdef CONFIG_MISC_INIT_R
-extern void load_sernum_ethaddr(void);
-int misc_init_r (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- load_sernum_ethaddr();
-
-#ifdef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ
- int scy, trlx, flash_or_timing, clk_diff;
-
- scy = (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_SCY_MSK) >> 4;
- if (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_TRLX) {
- trlx = OR_TRLX;
- scy *= 2;
- } else {
- trlx = 0;
- }
-
- /*
- * We assume that each 10MHz of bus clock require 1-clk SCY
- * adjustment.
- */
- clk_diff = (gd->bus_clk / 1000000) - 50;
-
- /*
- * We need proper rounding here. This is what the "+5" and "-5"
- * are here for.
- */
- if (clk_diff >= 0)
- scy += (clk_diff + 5) / 10;
- else
- scy += (clk_diff - 5) / 10;
-
- /*
- * For bus frequencies above 50MHz, we want to use relaxed timing
- * (OR_TRLX).
- */
- if (gd->bus_clk >= 50000000)
- trlx = OR_TRLX;
- else
- trlx = 0;
-
- if (trlx)
- scy /= 2;
-
- if (scy > 0xf)
- scy = 0xf;
- if (scy < 1)
- scy = 1;
-
- flash_or_timing = (scy << 4) | trlx |
- (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & ~(OR_TRLX | OR_SCY_MSK));
-
- memctl->memc_or0 =
- flash_or_timing | (-flash_info[0].size & OR_AM_MSK);
-#else
- memctl->memc_or0 =
- CONFIG_SYS_OR_TIMING_FLASH | (-flash_info[0].size & OR_AM_MSK);
-#endif
- memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V;
-
- debug ("## BR0: 0x%08x OR0: 0x%08x\n",
- memctl->memc_br0, memctl->memc_or0);
-
- if (flash_info[1].size) {
-#ifdef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ
- memctl->memc_or1 = flash_or_timing |
- (-flash_info[1].size & 0xFFFF8000);
-#else
- memctl->memc_or1 = CONFIG_SYS_OR_TIMING_FLASH |
- (-flash_info[1].size & 0xFFFF8000);
-#endif
- memctl->memc_br1 =
- ((CONFIG_SYS_FLASH_BASE +
- flash_info[0].
- size) & BR_BA_MSK) | BR_MS_GPCM | BR_V;
-
- debug ("## BR1: 0x%08x OR1: 0x%08x\n",
- memctl->memc_br1, memctl->memc_or1);
- } else {
- memctl->memc_br1 = 0; /* invalidate bank */
-
- debug ("## DISABLE BR1: 0x%08x OR1: 0x%08x\n",
- memctl->memc_br1, memctl->memc_or1);
- }
-
-# ifdef CONFIG_IDE_LED
- /* Configure PA15 as output port */
- immap->im_ioport.iop_padir |= 0x0001;
- immap->im_ioport.iop_paodr |= 0x0001;
- immap->im_ioport.iop_papar &= ~0x0001;
- immap->im_ioport.iop_padat &= ~0x0001; /* turn it off */
-# endif
-
- return (0);
-}
-#endif /* CONFIG_MISC_INIT_R */
-
-
-# ifdef CONFIG_IDE_LED
-void ide_led (uchar led, uchar status)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- /* We have one led for both pcmcia slots */
- if (status) { /* led on */
- immap->im_ioport.iop_padat |= 0x0001;
- } else {
- immap->im_ioport.iop_padat &= ~0x0001;
- }
-}
-# endif
-
-#ifdef CONFIG_LCD_INFO
-#include <lcd.h>
-#include <version.h>
-#include <timestamp.h>
-
-void lcd_show_board_info(void)
-{
- char temp[32];
-
- lcd_printf ("%s (%s - %s)\n", U_BOOT_VERSION, U_BOOT_DATE, U_BOOT_TIME);
- lcd_printf ("(C) 2008 DENX Software Engineering GmbH\n");
- lcd_printf (" Wolfgang DENK, wd@denx.de\n");
-#ifdef CONFIG_LCD_INFO_BELOW_LOGO
- lcd_printf ("MPC823 CPU at %s MHz\n",
- strmhz(temp, gd->cpu_clk));
- lcd_printf (" %ld MB RAM, %ld MB Flash\n",
- gd->ram_size >> 20,
- gd->bd->bi_flashsize >> 20 );
-#else
- /* leave one blank line */
- lcd_printf ("\nMPC823 CPU at %s MHz, %ld MB RAM, %ld MB Flash\n",
- strmhz(temp, gd->cpu_clk),
- gd->ram_size >> 20,
- gd->bd->bi_flashsize >> 20 );
-#endif /* CONFIG_LCD_INFO_BELOW_LOGO */
-}
-#endif /* CONFIG_LCD_INFO */
-
-/*
- * Device Tree Support
- */
-#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT)
-int fdt_set_node_and_value (void *blob,
- char *nodename,
- char *regname,
- void *var,
- int size)
-{
- int ret = 0;
- int nodeoffset = 0;
-
- nodeoffset = fdt_path_offset (blob, nodename);
- if (nodeoffset >= 0) {
- ret = fdt_setprop (blob, nodeoffset, regname, var,
- size);
- if (ret < 0) {
- printf("ft_blob_update(): "
- "cannot set %s/%s property; err: %s\n",
- nodename, regname, fdt_strerror (ret));
- }
- } else {
- printf("ft_blob_update(): "
- "cannot find %s node err:%s\n",
- nodename, fdt_strerror (nodeoffset));
- }
- return ret;
-}
-
-int fdt_del_node_name (void *blob, char *nodename)
-{
- int ret = 0;
- int nodeoffset = 0;
-
- nodeoffset = fdt_path_offset (blob, nodename);
- if (nodeoffset >= 0) {
- ret = fdt_del_node (blob, nodeoffset);
- if (ret < 0) {
- printf("%s: cannot delete %s; err: %s\n",
- __func__, nodename, fdt_strerror (ret));
- }
- } else {
- printf("%s: cannot find %s node err:%s\n",
- __func__, nodename, fdt_strerror (nodeoffset));
- }
- return ret;
-}
-
-int fdt_del_prop_name (void *blob, char *nodename, char *propname)
-{
- int ret = 0;
- int nodeoffset = 0;
-
- nodeoffset = fdt_path_offset (blob, nodename);
- if (nodeoffset >= 0) {
- ret = fdt_delprop (blob, nodeoffset, propname);
- if (ret < 0) {
- printf("%s: cannot delete %s %s; err: %s\n",
- __func__, nodename, propname,
- fdt_strerror (ret));
- }
- } else {
- printf("%s: cannot find %s node err:%s\n",
- __func__, nodename, fdt_strerror (nodeoffset));
- }
- return ret;
-}
-
-/*
- * update "brg" property in the blob
- */
-void ft_blob_update (void *blob, bd_t *bd)
-{
- uchar enetaddr[6];
- ulong brg_data = 0;
-
- /* BRG */
- brg_data = cpu_to_be32(bd->bi_busfreq);
- fdt_set_node_and_value(blob,
- "/soc/cpm", "brg-frequency",
- &brg_data, sizeof(brg_data));
-
- /* MAC addr */
- if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
- fdt_set_node_and_value(blob,
- "ethernet0", "local-mac-address",
- enetaddr, sizeof(u8) * 6);
- }
-
- if (hwconfig_arg_cmp("fec", "off")) {
- /* no FEC on this plattform, delete DTS nodes */
- fdt_del_node_name (blob, "ethernet1");
- fdt_del_node_name (blob, "mdio1");
- /* also the aliases entries */
- fdt_del_prop_name (blob, "/aliases", "ethernet1");
- fdt_del_prop_name (blob, "/aliases", "mdio1");
- } else {
- /* adjust local-mac-address for FEC ethernet */
- if (eth_getenv_enetaddr("eth1addr", enetaddr)) {
- fdt_set_node_and_value(blob,
- "ethernet1", "local-mac-address",
- enetaddr, sizeof(u8) * 6);
- }
- }
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
- ft_blob_update(blob, bd);
-
- return 0;
-}
-#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
diff --git a/board/tqc/tqm8xx/u-boot.lds b/board/tqc/tqm8xx/u-boot.lds
deleted file mode 100644
index 44dfafae2964dbbf94285e094f4c5aa46b7a794d..0000000000000000000000000000000000000000
--- a/board/tqc/tqm8xx/u-boot.lds
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * (C) Copyright 2000-2012
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
- arch/powerpc/cpu/mpc8xx/built-in.o (.text*)
- arch/powerpc/lib/built-in.o (.text*)
- board/tqc/tqm8xx/built-in.o (.text*)
- disk/built-in.o (.text*)
- drivers/net/built-in.o (.text*)
- drivers/built-in.o (.text.pcmcia_on)
- drivers/built-in.o (.text.pcmcia_hardware_enable)
-
- . = DEFINED(env_offset) ? env_offset : .;
- common/env_embedded.o (.ppcenv*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/cmd/bdinfo.c b/cmd/bdinfo.c
index 41ab8e8089fa2f2170961b3bfcea27f68d931a45..484a8532ed9b8eaea895cc40e95aa0f29d5a6af1 100644
--- a/cmd/bdinfo.c
+++ b/cmd/bdinfo.c
@@ -183,7 +183,7 @@ int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
print_bi_flash(bd);
print_num("sramstart", bd->bi_sramstart);
print_num("sramsize", bd->bi_sramsize);
-#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || \
+#if defined(CONFIG_5xx) || \
defined(CONFIG_MPC8260) || defined(CONFIG_E500)
print_num("immr_base", bd->bi_immr_base);
#endif
diff --git a/cmd/bedbug.c b/cmd/bedbug.c
index 69afeafecb5652d180d6329f24db8bf3af535cf8..14663dc95cc1ebe05e3c2c379200897faff394df 100644
--- a/cmd/bedbug.c
+++ b/cmd/bedbug.c
@@ -52,10 +52,6 @@ void bedbug_init (void)
void bedbug405_init (void);
bedbug405_init ();
-#elif defined(CONFIG_8xx)
- void bedbug860_init (void);
-
- bedbug860_init ();
#endif
#if defined(CONFIG_MPC824X) || defined(CONFIG_MPC8260)
diff --git a/cmd/ide.c b/cmd/ide.c
index 0fd401b3c445a2f452d9483b0479acf73e98054f..10fb2f95a7f371154cf3e52a72defc0384d311fa 100644
--- a/cmd/ide.c
+++ b/cmd/ide.c
@@ -18,7 +18,7 @@
#include <asm/byteorder.h>
#include <asm/io.h>
-#if defined(CONFIG_IDE_8xx_DIRECT) || defined(CONFIG_IDE_PCMCIA)
+#if defined(CONFIG_IDE_PCMCIA)
# include <pcmcia.h>
#endif
@@ -42,12 +42,7 @@ int do_ide(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
return CMD_RET_USAGE;
case 2:
if (strncmp(argv[1], "res", 3) == 0) {
- puts("\nReset IDE"
-#ifdef CONFIG_IDE_8xx_DIRECT
- " on PCMCIA " PCMCIA_SLOT_MSG
-#endif
- ": ");
-
+ puts("\nReset IDE: ");
ide_init();
return 0;
} else if (strncmp(argv[1], "inf", 3) == 0) {
diff --git a/cmd/pcmcia.c b/cmd/pcmcia.c
index 044fb9e6189466f246bbe412294e9d79e6702a3e..0bf2bd654f69fa025704b659357d182cd476b747 100644
--- a/cmd/pcmcia.c
+++ b/cmd/pcmcia.c
@@ -83,10 +83,6 @@ U_BOOT_CMD(
#undef CHECK_IDE_DEVICE
-#if defined(CONFIG_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define CHECK_IDE_DEVICE
-#endif
-
#if defined(CONFIG_PXA_PCMCIA)
#define CHECK_IDE_DEVICE
#endif
diff --git a/cmd/reginfo.c b/cmd/reginfo.c
index a3696d1b00770bc9c0d8e301f479e2ffcd334c90..d971a8fd80f30c1e496954510f0c47b8be792da3 100644
--- a/cmd/reginfo.c
+++ b/cmd/reginfo.c
@@ -7,9 +7,7 @@
#include <common.h>
#include <command.h>
-#if defined(CONFIG_8xx)
-#include <mpc8xx.h>
-#elif defined (CONFIG_4xx)
+#if defined (CONFIG_4xx)
extern void ppc4xx_reginfo(void);
#elif defined (CONFIG_5xx)
#include <mpc5xx.h>
@@ -24,60 +22,7 @@ extern void mpc85xx_reginfo(void);
static int do_reginfo(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
{
-#if defined(CONFIG_8xx)
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- volatile sysconf8xx_t *sysconf = &immap->im_siu_conf;
- volatile sit8xx_t *timers = &immap->im_sit;
-
- /* Hopefully more PowerPC knowledgable people will add code to display
- * other useful registers
- */
-
- printf ("\nSystem Configuration registers\n"
-
- "\tIMMR\t0x%08X\n", get_immr(0));
-
- printf("\tSIUMCR\t0x%08X", sysconf->sc_siumcr);
- printf("\tSYPCR\t0x%08X\n",sysconf->sc_sypcr);
-
- printf("\tSWT\t0x%08X", sysconf->sc_swt);
- printf("\tSWSR\t0x%04X\n", sysconf->sc_swsr);
-
- printf("\tSIPEND\t0x%08X\tSIMASK\t0x%08X\n",
- sysconf->sc_sipend, sysconf->sc_simask);
- printf("\tSIEL\t0x%08X\tSIVEC\t0x%08X\n",
- sysconf->sc_siel, sysconf->sc_sivec);
- printf("\tTESR\t0x%08X\tSDCR\t0x%08X\n",
- sysconf->sc_tesr, sysconf->sc_sdcr);
-
- printf ("Memory Controller Registers\n"
-
- "\tBR0\t0x%08X\tOR0\t0x%08X \n", memctl->memc_br0, memctl->memc_or0);
- printf("\tBR1\t0x%08X\tOR1\t0x%08X \n", memctl->memc_br1, memctl->memc_or1);
- printf("\tBR2\t0x%08X\tOR2\t0x%08X \n", memctl->memc_br2, memctl->memc_or2);
- printf("\tBR3\t0x%08X\tOR3\t0x%08X \n", memctl->memc_br3, memctl->memc_or3);
- printf("\tBR4\t0x%08X\tOR4\t0x%08X \n", memctl->memc_br4, memctl->memc_or4);
- printf("\tBR5\t0x%08X\tOR5\t0x%08X \n", memctl->memc_br5, memctl->memc_or5);
- printf("\tBR6\t0x%08X\tOR6\t0x%08X \n", memctl->memc_br6, memctl->memc_or6);
- printf("\tBR7\t0x%08X\tOR7\t0x%08X \n", memctl->memc_br7, memctl->memc_or7);
- printf ("\n"
- "\tmamr\t0x%08X\tmbmr\t0x%08X \n",
- memctl->memc_mamr, memctl->memc_mbmr );
- printf("\tmstat\t0x%08X\tmptpr\t0x%08X \n",
- memctl->memc_mstat, memctl->memc_mptpr );
- printf("\tmdr\t0x%08X \n", memctl->memc_mdr);
-
- printf ("\nSystem Integration Timers\n"
- "\tTBSCR\t0x%08X\tRTCSC\t0x%08X \n",
- timers->sit_tbscr, timers->sit_rtcsc);
- printf("\tPISCR\t0x%08X \n", timers->sit_piscr);
-
- /*
- * May be some CPM info here?
- */
-
-#elif defined (CONFIG_4xx)
+#if defined (CONFIG_4xx)
ppc4xx_reginfo();
#elif defined(CONFIG_5xx)
diff --git a/cmd/source.c b/cmd/source.c
index db7ab7e5f4092a0b996f96702e4ed53b9cd897bb..177f86bb54d946e9f32ab4e57460ae3403c778a6 100644
--- a/cmd/source.c
+++ b/cmd/source.c
@@ -22,9 +22,6 @@
#include <mapmem.h>
#include <asm/byteorder.h>
#include <asm/io.h>
-#if defined(CONFIG_8xx)
-#include <mpc8xx.h>
-#endif
int
source (ulong addr, const char *fit_uname)
diff --git a/common/board_f.c b/common/board_f.c
index 46e52849fb80f9a5a12a1b8ed0182d6fc02e9b75..a3f87043e275b7e602b7084cf60915afa146a147 100644
--- a/common/board_f.c
+++ b/common/board_f.c
@@ -387,7 +387,7 @@ static int reserve_video(void)
gd->fb_base = gd->relocaddr;
# endif /* CONFIG_FB_ADDR */
#elif defined(CONFIG_VIDEO) && \
- (!defined(CONFIG_PPC) || defined(CONFIG_8xx)) && \
+ (!defined(CONFIG_PPC)) && \
!defined(CONFIG_ARM) && !defined(CONFIG_X86) && \
!defined(CONFIG_M68K)
/* reserve memory for video display (always full pages) */
@@ -547,7 +547,7 @@ static int setup_board_part1(void)
bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE; /* size of SRAM */
#endif
-#if defined(CONFIG_8xx) || defined(CONFIG_MPC8260) || defined(CONFIG_5xx) || \
+#if defined(CONFIG_MPC8260) || defined(CONFIG_5xx) || \
defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
bd->bi_immr_base = CONFIG_SYS_IMMR; /* base of IMMR register */
#endif
diff --git a/common/board_r.c b/common/board_r.c
index 15977e4bcaef417b21a60c61a196e4bbfa13793a..adc1f1937ed1fd9bec0b1b6080e658a1f4f52fb0 100644
--- a/common/board_r.c
+++ b/common/board_r.c
@@ -227,13 +227,6 @@ static int initr_post_backlog(void)
}
#endif
-#ifdef CONFIG_SYS_DELAYED_ICACHE
-static int initr_icache_enable(void)
-{
- return 0;
-}
-#endif
-
#if defined(CONFIG_SYS_INIT_RAM_LOCK) && defined(CONFIG_E500)
static int initr_unlock_ram_in_cache(void)
{
@@ -639,11 +632,7 @@ static int initr_pcmcia(void)
#if defined(CONFIG_IDE)
static int initr_ide(void)
{
-#ifdef CONFIG_IDE_8xx_PCCARD
- puts("PCMCIA:");
-#else
puts("IDE: ");
-#endif
#if defined(CONFIG_START_IDE)
if (board_start_ide())
ide_init();
@@ -786,9 +775,6 @@ static init_fnc_t init_sequence_r[] = {
initr_post_backlog,
#endif
INIT_FUNC_WATCHDOG_RESET
-#ifdef CONFIG_SYS_DELAYED_ICACHE
- initr_icache_enable,
-#endif
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_EARLY_PCI_INIT)
/*
* Do early PCI configuration _before_ the flash gets initialised,
diff --git a/common/bootm_os.c b/common/bootm_os.c
index e1024069766ac949462603479bd609d8f1c287f3..d9e6e937f7ca627852d595ff23496b8d5af86fce 100644
--- a/common/bootm_os.c
+++ b/common/bootm_os.c
@@ -56,7 +56,6 @@ static int do_bootm_netbsd(int flag, int argc, char * const argv[],
void (*loader)(bd_t *, image_header_t *, char *, char *);
image_header_t *os_hdr, *hdr;
ulong kernel_data, kernel_len;
- char *consdev;
char *cmdline;
if (flag != BOOTM_STATE_OS_GO)
@@ -88,17 +87,6 @@ static int do_bootm_netbsd(int flag, int argc, char * const argv[],
os_hdr = hdr;
}
- consdev = "";
-#if defined(CONFIG_8xx_CONS_SMC1)
- consdev = "smc1";
-#elif defined(CONFIG_8xx_CONS_SMC2)
- consdev = "smc2";
-#elif defined(CONFIG_8xx_CONS_SCC2)
- consdev = "scc2";
-#elif defined(CONFIG_8xx_CONS_SCC3)
- consdev = "scc3";
-#endif
-
if (argc > 0) {
ulong len;
int i;
@@ -127,7 +115,7 @@ static int do_bootm_netbsd(int flag, int argc, char * const argv[],
* arg[2]: char pointer to the console device to use
* arg[3]: char pointer to the boot arguments
*/
- (*loader)(gd->bd, os_hdr, consdev, cmdline);
+ (*loader)(gd->bd, os_hdr, "", cmdline);
return 1;
}
diff --git a/common/lcd.c b/common/lcd.c
index 2405146cf09042e58a352a7aa29bd5dbacf93090..7e399cee2de6822a56703870302aa4eec987cc59 100644
--- a/common/lcd.c
+++ b/common/lcd.c
@@ -562,11 +562,7 @@ __weak void lcd_set_cmap(struct bmp_image *bmp, unsigned colors)
*cmap = (((cte.red) << 8) & 0xf800) |
(((cte.green) << 3) & 0x07e0) |
(((cte.blue) >> 3) & 0x001f);
-#if defined(CONFIG_MPC823)
- cmap--;
-#else
cmap++;
-#endif
}
}
diff --git a/configs/TQM823L_LCD_defconfig b/configs/TQM823L_LCD_defconfig
deleted file mode 100644
index ccb68b24c5aee3cfd2f1cf2bf4fb9367d48a5d42..0000000000000000000000000000000000000000
--- a/configs/TQM823L_LCD_defconfig
+++ /dev/null
@@ -1,24 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM823L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="NEC_NL6448BC20"
-CONFIG_BOOTDELAY=5
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM823L_defconfig b/configs/TQM823L_defconfig
deleted file mode 100644
index c588948e11a76cb21d4ab0c3894a5d27537ce261..0000000000000000000000000000000000000000
--- a/configs/TQM823L_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM823L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM823M_defconfig b/configs/TQM823M_defconfig
deleted file mode 100644
index 0490828504504c0160954c73e239cf717168cb76..0000000000000000000000000000000000000000
--- a/configs/TQM823M_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM823M=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM850L_defconfig b/configs/TQM850L_defconfig
deleted file mode 100644
index 0e42d8c4fe7cbd7df6df4a61f9ed79b192962405..0000000000000000000000000000000000000000
--- a/configs/TQM850L_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM850L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM850M_defconfig b/configs/TQM850M_defconfig
deleted file mode 100644
index a464fe507a0e9b0bec9c5f6019dc1a7d05624d61..0000000000000000000000000000000000000000
--- a/configs/TQM850M_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM850M=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM855L_defconfig b/configs/TQM855L_defconfig
deleted file mode 100644
index aa370012f5e352c011ebd1fc5f432eca6b1de0c4..0000000000000000000000000000000000000000
--- a/configs/TQM855L_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM855L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM855M_defconfig b/configs/TQM855M_defconfig
deleted file mode 100644
index faab826a24775c86bc3e4423ed3415bb76d1dc34..0000000000000000000000000000000000000000
--- a/configs/TQM855M_defconfig
+++ /dev/null
@@ -1,28 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM855M=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM860L_defconfig b/configs/TQM860L_defconfig
deleted file mode 100644
index b18cf31dddb0e17a250613b30d64f3fc19115fb7..0000000000000000000000000000000000000000
--- a/configs/TQM860L_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM860L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM860M_defconfig b/configs/TQM860M_defconfig
deleted file mode 100644
index fe2fe6d38cdffb1d640920c8a014e3a3febd51c4..0000000000000000000000000000000000000000
--- a/configs/TQM860M_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM860M=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM862L_defconfig b/configs/TQM862L_defconfig
deleted file mode 100644
index 6f5f772d32ea508e19a8720e1cda8c01f0a1e05f..0000000000000000000000000000000000000000
--- a/configs/TQM862L_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM862L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM862M_defconfig b/configs/TQM862M_defconfig
deleted file mode 100644
index 44307760ee0aa08c4d1bcba01b8590f5391df968..0000000000000000000000000000000000000000
--- a/configs/TQM862M_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM862M=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM866M_defconfig b/configs/TQM866M_defconfig
deleted file mode 100644
index d8922900d43106b0c340195d1de3f8317f90fd53..0000000000000000000000000000000000000000
--- a/configs/TQM866M_defconfig
+++ /dev/null
@@ -1,27 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM866M=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TQM885D_defconfig b/configs/TQM885D_defconfig
deleted file mode 100644
index 48421e3cfea5b59138bff60f3fc702610fe1b423..0000000000000000000000000000000000000000
--- a/configs/TQM885D_defconfig
+++ /dev/null
@@ -1,30 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM885D=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_LOOPW=y
-CONFIG_CMD_IDE=y
-CONFIG_CMD_I2C=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-CONFIG_LED_STATUS=y
-# CONFIG_LED_STATUS_BOARD_SPECIFIC is not set
-CONFIG_LED_STATUS0=y
-CONFIG_LED_STATUS_BIT=1
-CONFIG_LED_STATUS_STATE=1
-CONFIG_LED_STATUS_BOOT_ENABLE=y
-CONFIG_LED_STATUS_BOOT=0
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_OF_LIBFDT=y
diff --git a/configs/TTTech_defconfig b/configs/TTTech_defconfig
deleted file mode 100644
index 9d26e9461576477079687e8adc6191878a017c50..0000000000000000000000000000000000000000
--- a/configs/TTTech_defconfig
+++ /dev/null
@@ -1,24 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM823L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SHARP_LQ104V7DS01"
-CONFIG_BOOTDELAY=5
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/wtk_defconfig b/configs/wtk_defconfig
deleted file mode 100644
index 2b81535c29d22c486494391e965fc4405c5173c5..0000000000000000000000000000000000000000
--- a/configs/wtk_defconfig
+++ /dev/null
@@ -1,24 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_TQM823L=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="SHARP_LQ065T9DR51U"
-CONFIG_BOOTDELAY=5
-# CONFIG_CONSOLE_MUX is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_IDE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_BMP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_JFFS2=y
-CONFIG_MAC_PARTITION=y
-CONFIG_DOS_PARTITION=y
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-# CONFIG_PCI is not set
-CONFIG_LCD=y
-CONFIG_OF_LIBFDT=y
diff --git a/doc/README.LED b/doc/README.LED
index 7aa95bddf7873fdbce191917919241d1858a7660..c21c9d53ec35b14a3fdc24709c0a8bcb39ab4f55 100644
--- a/doc/README.LED
+++ b/doc/README.LED
@@ -73,6 +73,5 @@ These are weakly defined in arch/arm/lib/board.c to noops. Where applicable, def
these functions in the board specific source.
TBD : Describe older board dependent macros similar to what is done for
-CONFIG_TQM8xxL.
TBD : Describe general support via asm/status_led.h
diff --git a/doc/README.MPC866 b/doc/README.MPC866
deleted file mode 100644
index 4707cb7df7d6362ee2887085fd5e8291b33c96e9..0000000000000000000000000000000000000000
--- a/doc/README.MPC866
+++ /dev/null
@@ -1,24 +0,0 @@
-The current implementation allows the user to specify the desired CPU
-clock value, in MHz, via an environment variable "cpuclk".
-
-Four compile-time constants are used:
-
- CONFIG_8xx_OSCLK - input quartz clock
- CONFIG_SYS_8xx_CPUCLK_MIN - minimum allowed CPU clock
- CONFIG_SYS_8xx_CPUCLK_MAX - maximum allowed CPU clock
- CONFIG_8xx_CPUCLK_DEFAULT - default CPU clock value
-
-If the "cpuclk" environment variable value is within the CPUCLK_MIN /
-CPUCLK_MAX limits, the specified value is used. Otherwise, the
-default CPU clock value is set.
-
-Please make sure you understand what you are doing, and understand
-the restrictions of your hardware (board, processor). For example,
-ethernet will stop working for CPU clock frequencies below 25 MHz.
-
-Please note that the new clock-handling code is enabled if
-CONFIG_8xx_CPUCLK_DEFAULT is defined. Since this mechanism supports
-only MPC866 and newer CPUs, this constant MUST NOT be defined for
-MPC823/850/860/862 series. The clock generation algorithm for older
-chips is different and has not been implemented yet. If you need it,
-your patch is welcome.
diff --git a/doc/README.fsl-clk b/doc/README.fsl-clk
deleted file mode 100644
index 9e83c24f23a92b28e54f0d5d45e21a7e32633da6..0000000000000000000000000000000000000000
--- a/doc/README.fsl-clk
+++ /dev/null
@@ -1,6 +0,0 @@
-Freescale system clock options
-
- - CONFIG_SYS_FSL_CLK
- Enable to call get_clocks() in board_init_f() for
- non-PPC platforms and PCC 8xx platforms such as
- TQM866M and TQM885D.
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 200f6708060b8e0f4090e60b47a5cb7dfc4fd8e9..11d3acc5504da26d36586b48ac8b25c9784be0f5 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -316,7 +316,6 @@ ADCIOP powerpc ppc4xx 99bcad1 2012-09-19 Matthias Fuc
DASA_SIM powerpc ppc4xx 99bcad1 2012-09-19 Matthias Fuchs <matthias.fuchs@esd-electronics.com>
apollon arm omap24xx 535c74f 2012-09-18 Kyungmin Park <kyungmin.park@samsung.com>
tb0229 mips mips32 3f3110d 2011-12-12
-rmu powerpc MPC850 fb82fd7 2011-12-07 Wolfgang Denk <wd@denx.de>
OXC powerpc MPC8240 309a292 2011-12-07
BAB7xx powerpc MPC740/MPC750 c53043b 2011-12-07 Frank Gottschling <fgottschling@eltec.de>
xm250 arm pxa c477d72 2011-11-25
diff --git a/drivers/block/ide.c b/drivers/block/ide.c
index ac5b91c01ad26a53b2ad976697fb92c39a1486d5..308ad7396bc6a0da6c1ff3eaca2ab79ac769c76f 100644
--- a/drivers/block/ide.c
+++ b/drivers/block/ide.c
@@ -770,10 +770,6 @@ void ide_init(void)
unsigned char c;
int i, bus;
-#ifdef CONFIG_IDE_8xx_PCCARD
- extern int ide_devices_found; /* Initialized in check_ide_device() */
-#endif /* CONFIG_IDE_8xx_PCCARD */
-
#ifdef CONFIG_IDE_PREINIT
WATCHDOG_RESET();
@@ -812,13 +808,6 @@ void ide_init(void)
bus * (CONFIG_SYS_IDE_MAXDEVICE /
CONFIG_SYS_IDE_MAXBUS);
-#ifdef CONFIG_IDE_8xx_PCCARD
- /* Skip non-ide devices from probing */
- if ((ide_devices_found & (1 << bus)) == 0) {
- ide_led((LED_IDE1 | LED_IDE2), 0); /* LED's off */
- continue;
- }
-#endif
printf("Bus %d: ", bus);
ide_bus_ok[bus] = 0;
diff --git a/drivers/block/sil680.c b/drivers/block/sil680.c
index b1db257838b809d837ce46d06c84dc6fc70564ce..bca3397d948e2b78d5c63e16a4bdf672aeee7673 100644
--- a/drivers/block/sil680.c
+++ b/drivers/block/sil680.c
@@ -18,7 +18,6 @@
* #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0
*
* #define CONFIG_IDE
- * #undef CONFIG_IDE_8xx_DIRECT
* #undef CONFIG_IDE_LED
* #undef CONFIG_IDE_RESET
* #define CONFIG_IDE_PREINIT
diff --git a/drivers/bootcount/bootcount.c b/drivers/bootcount/bootcount.c
index d5ce450c153132c082b2aa7c991e79a1aa2c7fad..f922cfb23cd5c182555ad2c63ffdac001fe359e8 100644
--- a/drivers/bootcount/bootcount.c
+++ b/drivers/bootcount/bootcount.c
@@ -24,11 +24,6 @@
#define CONFIG_SYS_BOOTCOUNT_SINGLEWORD
#endif /* defined(CONFIG_MPC512X) */
-#if defined(CONFIG_8xx)
-#define CONFIG_SYS_BOOTCOUNT_ADDR (((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_dpmem + \
- CPM_BOOTCOUNT_ADDR)
-#endif /* defined(CONFIG_8xx) */
-
#if defined(CONFIG_MPC8260)
#include <asm/cpm_8260.h>
#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_IMMR + CPM_BOOTCOUNT_ADDR)
diff --git a/drivers/i2c/i2c_core.c b/drivers/i2c/i2c_core.c
index 19769dab67f232678515d43b93ad29e9c6be25c4..911563be0bd370d692b000ab89155de1d3700a7d 100644
--- a/drivers/i2c/i2c_core.c
+++ b/drivers/i2c/i2c_core.c
@@ -323,11 +323,6 @@ uint8_t i2c_reg_read(uint8_t addr, uint8_t reg)
{
uint8_t buf;
-#ifdef CONFIG_8xx
- /* MPC8xx needs this. Maybe one day we can get rid of it. */
- /* maybe it is now the time for it ... */
- i2c_set_bus_num(i2c_get_bus_num());
-#endif
i2c_read(addr, reg, 1, &buf, 1);
#ifdef DEBUG
@@ -340,12 +335,6 @@ uint8_t i2c_reg_read(uint8_t addr, uint8_t reg)
void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val)
{
-#ifdef CONFIG_8xx
- /* MPC8xx needs this. Maybe one day we can get rid of it. */
- /* maybe it is now the time for it ... */
- i2c_set_bus_num(i2c_get_bus_num());
-#endif
-
#ifdef DEBUG
printf("%s: bus=%d addr=0x%02x, reg=0x%02x, val=0x%02x\n",
__func__, i2c_get_bus_num(), addr, reg, val);
diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c
index c102a1ab10a1109964c976908fc1e027a3e145be..9380a041b2fa52c9a79edae72a7776bf8f8cd8b5 100644
--- a/drivers/i2c/soft_i2c.c
+++ b/drivers/i2c/soft_i2c.c
@@ -97,9 +97,6 @@ DECLARE_GLOBAL_DATA_PTR;
# if defined(CONFIG_MPC8260)
# define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = \
ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT);
-# elif defined(CONFIG_8xx)
-# define I2C_SOFT_DECLARATIONS volatile immap_t *immr = \
- (immap_t *)CONFIG_SYS_IMMR;
# else
# define I2C_SOFT_DECLARATIONS
# endif
diff --git a/drivers/net/4xx_enet.c b/drivers/net/4xx_enet.c
index ca1139676b23fff4d0f006a821fbaceb1916d30a..e759339a5f5aea296f117f644642c9cf6cd0f165 100644
--- a/drivers/net/4xx_enet.c
+++ b/drivers/net/4xx_enet.c
@@ -67,7 +67,6 @@
#include <asm/io.h>
#include <asm/cache.h>
#include <asm/mmu.h>
-#include <commproc.h>
#include <asm/ppc4xx.h>
#include <asm/ppc4xx-emac.h>
#include <asm/ppc4xx-mal.h>
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index c506f796fa1c78cb898dfa53b9b24fe7ca206846..b7e6188429d0fbaf1d50329cb3167612a881f043 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -5,7 +5,5 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_8xx) += mpc8xx_pcmcia.o
obj-$(CONFIG_IDE_TI_CARDBUS) += ti_pci1410a.o
-obj-y += tqm8xx_pcmcia.o
obj-$(CONFIG_MARUBUN_PCCARD) += marubun_pcmcia.o
diff --git a/drivers/pcmcia/mpc8xx_pcmcia.c b/drivers/pcmcia/mpc8xx_pcmcia.c
deleted file mode 100644
index dae5560f8cd9b05c61c53a10b5d6070d653a0c1c..0000000000000000000000000000000000000000
--- a/drivers/pcmcia/mpc8xx_pcmcia.c
+++ /dev/null
@@ -1,258 +0,0 @@
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-#include <linux/compiler.h>
-
-#undef CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_PCMCIA)
-
-#if defined(CONFIG_IDE_8xx_PCCARD)
-extern int check_ide_device (int slot);
-#endif
-
-extern int pcmcia_hardware_enable (int slot);
-extern int pcmcia_voltage_set(int slot, int vcc, int vpp);
-
-#if defined(CONFIG_CMD_PCMCIA)
-extern int pcmcia_hardware_disable(int slot);
-#endif
-
-static u_int m8xx_get_graycode(u_int size);
-#if 0 /* Disabled */
-static u_int m8xx_get_speed(u_int ns, u_int is_io);
-#endif
-
-/* look up table for pgcrx registers */
-u_int *pcmcia_pgcrx[2] = {
- &((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pgcra,
- &((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pgcrb,
-};
-
-/*
- * Search this table to see if the windowsize is
- * supported...
- */
-
-#define M8XX_SIZES_NO 32
-
-static const u_int m8xx_size_to_gray[M8XX_SIZES_NO] =
-{ 0x00000001, 0x00000002, 0x00000008, 0x00000004,
- 0x00000080, 0x00000040, 0x00000010, 0x00000020,
- 0x00008000, 0x00004000, 0x00001000, 0x00002000,
- 0x00000100, 0x00000200, 0x00000800, 0x00000400,
-
- 0x0fffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0x01000000, 0x02000000, 0xffffffff, 0x04000000,
- 0x00010000, 0x00020000, 0x00080000, 0x00040000,
- 0x00800000, 0x00400000, 0x00100000, 0x00200000 };
-
-
-/* -------------------------------------------------------------------- */
-
-#define CONFIG_SYS_PCMCIA_TIMING ( PCMCIA_SHT(2) \
- | PCMCIA_SST(4) \
- | PCMCIA_SL(9))
-
-/* -------------------------------------------------------------------- */
-
-int pcmcia_on (void)
-{
- u_long reg, base;
- pcmcia_win_t *win;
- u_int rc, slot;
- __maybe_unused u_int slotbit;
- int i;
-
- debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- /* intialize the fixed memory windows */
- win = (pcmcia_win_t *)(&((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pbr0);
- base = CONFIG_SYS_PCMCIA_MEM_ADDR;
-
- if((reg = m8xx_get_graycode(CONFIG_SYS_PCMCIA_MEM_SIZE)) == -1) {
- printf ("Cannot set window size to 0x%08x\n",
- CONFIG_SYS_PCMCIA_MEM_SIZE);
- return (1);
- }
-
- slotbit = PCMCIA_SLOT_x;
- for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
- win->br = base;
-
-#if (PCMCIA_SOCKETS_NO == 2)
- if (i == 4) /* Another slot starting from win 4 */
- slotbit = (slotbit ? PCMCIA_PSLOT_A : PCMCIA_PSLOT_B);
-#endif
- switch (i) {
-#ifdef CONFIG_IDE_8xx_PCCARD
- case 4:
- case 0: { /* map attribute memory */
- win->or = ( PCMCIA_BSIZE_64M
- | PCMCIA_PPS_8
- | PCMCIA_PRS_ATTR
- | slotbit
- | PCMCIA_PV
- | CONFIG_SYS_PCMCIA_TIMING );
- break;
- }
- case 5:
- case 1: { /* map I/O window for data reg */
- win->or = ( PCMCIA_BSIZE_1K
- | PCMCIA_PPS_16
- | PCMCIA_PRS_IO
- | slotbit
- | PCMCIA_PV
- | CONFIG_SYS_PCMCIA_TIMING );
- break;
- }
- case 6:
- case 2: { /* map I/O window for cmd/ctrl reg block */
- win->or = ( PCMCIA_BSIZE_1K
- | PCMCIA_PPS_8
- | PCMCIA_PRS_IO
- | slotbit
- | PCMCIA_PV
- | CONFIG_SYS_PCMCIA_TIMING );
- break;
- }
-#endif /* CONFIG_IDE_8xx_PCCARD */
- default: /* set to not valid */
- win->or = 0;
- break;
- }
-
- debug ("MemWin %d: PBR 0x%08lX POR %08lX\n",
- i, win->br, win->or);
- base += CONFIG_SYS_PCMCIA_MEM_SIZE;
- ++win;
- }
-
- for (i=0, rc=0, slot=_slot_; i<PCMCIA_SOCKETS_NO; i++, slot = !slot) {
- /* turn off voltage */
- if ((rc = pcmcia_voltage_set(slot, 0, 0)))
- continue;
-
- /* Enable external hardware */
- if ((rc = pcmcia_hardware_enable(slot)))
- continue;
-
-#ifdef CONFIG_IDE_8xx_PCCARD
- if ((rc = check_ide_device(i)))
- continue;
-#endif
- }
- return rc;
-}
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_off (void)
-{
- int i;
- pcmcia_win_t *win;
-
- printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
-
- /* clear interrupt state, and disable interrupts */
- ((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pscr = PCMCIA_MASK(_slot_);
- ((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /* turn off interrupt and disable CxOE */
- PCMCIA_PGCRX(_slot_) = __MY_PCMCIA_GCRX_CXOE;
-
- /* turn off memory windows */
- win = (pcmcia_win_t *)(&((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia.pcmc_pbr0);
-
- for (i=0; i<PCMCIA_MEM_WIN_NO; ++i) {
- /* disable memory window */
- win->or = 0;
- ++win;
- }
-
- /* turn off voltage */
- pcmcia_voltage_set(_slot_, 0, 0);
-
- /* disable external hardware */
- printf ("Shutdown and Poweroff " PCMCIA_SLOT_MSG "\n");
- pcmcia_hardware_disable(_slot_);
- return 0;
-}
-#endif
-
-
-static u_int m8xx_get_graycode(u_int size)
-{
- u_int k;
-
- for (k = 0; k < M8XX_SIZES_NO; k++) {
- if(m8xx_size_to_gray[k] == size)
- break;
- }
-
- if((k == M8XX_SIZES_NO) || (m8xx_size_to_gray[k] == -1))
- k = -1;
-
- return k;
-}
-
-#if 0
-
-static u_int m8xx_get_speed(u_int ns, u_int is_io)
-{
- u_int reg, clocks, psst, psl, psht;
-
- if(!ns) {
-
- /*
- * We get called with IO maps setup to 0ns
- * if not specified by the user.
- * They should be 255ns.
- */
-
- if(is_io)
- ns = 255;
- else
- ns = 100; /* fast memory if 0 */
- }
-
- /*
- * In PSST, PSL, PSHT fields we tell the controller
- * timing parameters in CLKOUT clock cycles.
- * CLKOUT is the same as GCLK2_50.
- */
-
- /* how we want to adjust the timing - in percent */
-
-#define ADJ 180 /* 80 % longer accesstime - to be sure */
-
- clocks = ((M8XX_BUSFREQ / 1000) * ns) / 1000;
- clocks = (clocks * ADJ) / (100*1000);
-
- if(clocks >= PCMCIA_BMT_LIMIT) {
- DEBUG(0, "Max access time limit reached\n");
- clocks = PCMCIA_BMT_LIMIT-1;
- }
-
- psst = clocks / 7; /* setup time */
- psht = clocks / 7; /* hold time */
- psl = (clocks * 5) / 7; /* strobe length */
-
- psst += clocks - (psst + psht + psl);
-
- reg = psst << 12;
- reg |= psl << 7;
- reg |= psht << 16;
-
- return reg;
-}
-#endif /* 0 */
-
-#endif /* CONFIG_PCMCIA */
diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c
deleted file mode 100644
index edff50f630d6684eb9503fff2238694535db6ef8..0000000000000000000000000000000000000000
--- a/drivers/pcmcia/tqm8xx_pcmcia.c
+++ /dev/null
@@ -1,254 +0,0 @@
-/* -------------------------------------------------------------------- */
-/* TQM8xxL Boards by TQ Components */
-/* SC8xx Boards by SinoVee Microsystems */
-/* -------------------------------------------------------------------- */
-#include <common.h>
-#include <asm/io.h>
-#ifdef CONFIG_8xx
-#include <mpc8xx.h>
-#endif
-#include <pcmcia.h>
-
-#undef CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_PCMCIA) \
- && defined(CONFIG_TQM8xxL)
-
-#if defined(CONFIG_TQM8xxL)
-#define PCMCIA_BOARD_MSG "TQM8xxL"
-#endif
-
-static inline void power_config(int slot)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- /*
- * Configure Port C pins for
- * 5 Volts Enable and 3 Volts enable
- */
- clrbits_be16(&immap->im_ioport.iop_pcpar, 0x0002 | 0x0004);
- clrbits_be16(&immap->im_ioport.iop_pcso, 0x0002 | 0x0004);
-}
-
-static inline void power_off(int slot)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- clrbits_be16(&immap->im_ioport.iop_pcdat, 0x0002 | 0x0004);
-}
-
-static inline void power_on_5_0(int slot)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- setbits_be16(&immap->im_ioport.iop_pcdat, 0x0004);
- setbits_be16(&immap->im_ioport.iop_pcdir, 0x0002 | 0x0004);
-}
-
-static inline void power_on_3_3(int slot)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- setbits_be16(&immap->im_ioport.iop_pcdat, 0x0002);
- setbits_be16(&immap->im_ioport.iop_pcdir, 0x0002 | 0x0004);
-}
-
-/*
- * Function to retrieve the PIPR register, used for debuging purposes.
- */
-static inline uint32_t debug_get_pipr(void)
-{
- uint32_t pipr = 0;
-#ifdef DEBUG
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- pipr = in_be32(&immap->im_pcmcia.pcmc_pipr);
-#endif
- return pipr;
-}
-
-
-static inline int check_card_is_absent(int slot)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- uint32_t pipr = in_be32(&immap->im_pcmcia.pcmc_pipr);
- return pipr & (0x18000000 >> (slot << 4));
-}
-
-#define NSCU_GCRX_CXOE __MY_PCMCIA_GCRX_CXOE
-
-int pcmcia_hardware_enable(int slot)
-{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- uint reg, mask;
-
- debug("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- udelay(10000);
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
-
- /* Set DBGC to 00 */
- clrbits_be32(&immap->im_siu_conf.sc_siumcr, SIUMCR_DBGC11);
-
- /* Clear interrupt state, and disable interrupts */
- out_be32(&immap->im_pcmcia.pcmc_pscr, PCMCIA_MASK(slot));
- clrbits_be32(&immap->im_pcmcia.pcmc_per, PCMCIA_MASK(slot));
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= NSCU_GCRX_CXOE;
-
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- power_config(slot);
- power_off(slot);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- reg = debug_get_pipr();
- debug("[%d] %s: PIPR(%p)=0x%x\n", __LINE__, __FUNCTION__,
- &immap->im_pcmcia.pcmc_pipr, reg);
-
- if (check_card_is_absent(slot)) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = in_be32(&immap->im_pcmcia.pcmc_pipr);
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg & PCMCIA_VS1(slot)) ? "n" : "ff",
- (reg & PCMCIA_VS2(slot)) ? "n" : "ff");
-
- if ((reg & mask) == mask) {
- power_on_5_0(slot);
- puts (" 5.0V card found: ");
- } else {
- power_on_3_3(slot);
- puts (" 3.3V card found: ");
- }
-
-#if 0
- /* VCC switch error flag, PCMCIA slot INPACK_ pin */
- cp->cp_pbdir &= ~(0x0020 | 0x0010);
- cp->cp_pbpar &= ~(0x0020 | 0x0010);
- udelay(500000);
-#endif
-
- udelay(1000);
- debug("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- reg &= ~NSCU_GCRX_CXOE;
-
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable(int slot)
-{
- u_long reg;
-
- debug("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- /* remove all power */
- power_off(slot);
-
- debug("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= NSCU_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
-
- udelay(10000);
-
- return (0);
-}
-#endif
-
-int pcmcia_voltage_set(int slot, int vcc, int vpp)
-{
- u_long reg;
- uint32_t pipr = 0;
-
- debug("voltage_set: " PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- reg |= NSCU_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug("PCMCIA power OFF\n");
- power_config(slot);
- power_off(slot);
-
- switch(vcc) {
- case 0: break;
- case 33: power_on_3_3(slot); break;
- case 50: power_on_5_0(slot); break;
- default: goto done;
- }
-
- /* Checking supported voltages */
- pipr = debug_get_pipr();
- debug("PIPR: 0x%x --> %s\n", pipr,
- (pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- if (vcc)
- debug("PCMCIA powered at %sV\n", (vcc == 50) ? "5.0" : "3.3");
- else
- debug("PCMCIA powered down\n");
-
-done:
- debug("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(slot);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- reg &= ~NSCU_GCRX_CXOE; /* active low */
-
- PCMCIA_PGCRX(slot) = reg;
- udelay(500);
-
- debug("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A');
- return 0;
-}
-
-#endif /* CONFIG_PCMCIA && CONFIG_TQM8xxL */
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 438681da7a4cb852e2e6fe2b24d4c29dabdfdcb0..3bc918c1a00c0ff64141e7326fd92ebe0cc5c986 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -39,7 +39,6 @@ obj-$(CONFIG_RTC_MCP79411) += ds1307.o
obj-$(CONFIG_MCFRTC) += mcfrtc.o
obj-$(CONFIG_RTC_MK48T59) += mk48t59.o
obj-$(CONFIG_RTC_MPC5200) += mpc5xxx.o
-obj-$(CONFIG_RTC_MPC8xx) += mpc8xx.o
obj-$(CONFIG_RTC_MV) += mvrtc.o
obj-$(CONFIG_RTC_MX27) += mx27rtc.o
obj-$(CONFIG_RTC_MXS) += mxsrtc.o
diff --git a/drivers/rtc/mpc8xx.c b/drivers/rtc/mpc8xx.c
deleted file mode 100644
index 147a225c6b0a651c5694e7b45ffc1af26601bcfd..0000000000000000000000000000000000000000
--- a/drivers/rtc/mpc8xx.c
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Date & Time support for internal RTC of MPC8xx
- */
-
-/*#define DEBUG*/
-
-#include <common.h>
-#include <command.h>
-#include <rtc.h>
-
-#if defined(CONFIG_CMD_DATE)
-
-/* ------------------------------------------------------------------------- */
-
-int rtc_get (struct rtc_time *tmp)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- ulong tim;
-
- tim = immr->im_sit.sit_rtc;
-
- rtc_to_tm(tim, tmp);
-
- debug ( "Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n",
- tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
- tmp->tm_hour, tmp->tm_min, tmp->tm_sec);
-
- return 0;
-}
-
-int rtc_set (struct rtc_time *tmp)
-{
- volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- ulong tim;
-
- debug ( "Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n",
- tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday,
- tmp->tm_hour, tmp->tm_min, tmp->tm_sec);
-
- tim = rtc_mktime(tmp);
-
- immr->im_sitk.sitk_rtck = KAPWR_KEY;
- immr->im_sit.sit_rtc = tim;
-
- return 0;
-}
-
-void rtc_reset (void)
-{
- return; /* nothing to do */
-}
-
-#endif
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index 0fbbb7c82c698dd0ea882fb868fce72669d02e54..5e316a7cff956db270ccfb0ca211c06e05c80633 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -41,7 +41,6 @@ ifdef CONFIG_USB_DEVICE
obj-y += core.o
obj-y += ep0.o
obj-$(CONFIG_DW_UDC) += designware_udc.o
-obj-$(CONFIG_MPC885_FAMILY) += mpc8xx_udc.o
obj-$(CONFIG_CPU_PXA27X) += pxa27x_udc.o
endif
endif
diff --git a/drivers/usb/gadget/mpc8xx_udc.c b/drivers/usb/gadget/mpc8xx_udc.c
deleted file mode 100644
index ad5ea7a6b86007971f1616feca88e1962d4be22a..0000000000000000000000000000000000000000
--- a/drivers/usb/gadget/mpc8xx_udc.c
+++ /dev/null
@@ -1,1386 +0,0 @@
-/*
- * Copyright (C) 2006 by Bryan O'Donoghue, CodeHermit
- * bodonoghue@CodeHermit.ie
- *
- * References
- * DasUBoot/drivers/usb/gadget/omap1510_udc.c, for design and implementation
- * ideas.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Notes :
- * 1. #define __SIMULATE_ERROR__ to inject a CRC error into every 2nd TX
- * packet to force the USB re-transmit protocol.
- *
- * 2. #define __DEBUG_UDC__ to switch on debug tracing to serial console
- * be careful that tracing doesn't create Hiesen-bugs with respect to
- * response timeouts to control requests.
- *
- * 3. This driver should be able to support any higher level driver that
- * that wants to do either of the two standard UDC implementations
- * Control-Bulk-Interrupt or Bulk-IN/Bulk-Out standards. Hence
- * gserial and cdc_acm should work with this code.
- *
- * 4. NAK events never actually get raised at all, the documentation
- * is just wrong !
- *
- * 5. For some reason, cbd_datlen is *always* +2 the value it should be.
- * this means that having an RX cbd of 16 bytes is not possible, since
- * the same size is reported for 14 bytes received as 16 bytes received
- * until we can find out why this happens, RX cbds must be limited to 8
- * bytes. TODO: check errata for this behaviour.
- *
- * 6. Right now this code doesn't support properly powering up with the USB
- * cable attached to the USB host my development board the Adder87x doesn't
- * have a pull-up fitted to allow this, so it is necessary to power the
- * board and *then* attached the USB cable to the host. However somebody
- * with a different design in their board may be able to keep the cable
- * constantly connected and simply enable/disable a pull-up re
- * figure 31.1 in MPC885RM.pdf instead of having to power up the board and
- * then attach the cable !
- *
- */
-#include <common.h>
-#include <config.h>
-#include <commproc.h>
-#include <usbdevice.h>
-#include <usb/mpc8xx_udc.h>
-#include <usb/udc.h>
-
-#include "ep0.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define ERR(fmt, args...)\
- serial_printf("ERROR : [%s] %s:%d: "fmt,\
- __FILE__,__FUNCTION__,__LINE__, ##args)
-#ifdef __DEBUG_UDC__
-#define DBG(fmt,args...)\
- serial_printf("[%s] %s:%d: "fmt,\
- __FILE__,__FUNCTION__,__LINE__, ##args)
-#else
-#define DBG(fmt,args...)
-#endif
-
-/* Static Data */
-#ifdef __SIMULATE_ERROR__
-static char err_poison_test = 0;
-#endif
-static struct mpc8xx_ep ep_ref[MAX_ENDPOINTS];
-static u32 address_base = STATE_NOT_READY;
-static mpc8xx_udc_state_t udc_state = 0;
-static struct usb_device_instance *udc_device = 0;
-static volatile usb_epb_t *endpoints[MAX_ENDPOINTS];
-static volatile cbd_t *tx_cbd[TX_RING_SIZE];
-static volatile cbd_t *rx_cbd[RX_RING_SIZE];
-static volatile immap_t *immr = 0;
-static volatile cpm8xx_t *cp = 0;
-static volatile usb_pram_t *usb_paramp = 0;
-static volatile usb_t *usbp = 0;
-static int rx_ct = 0;
-static int tx_ct = 0;
-
-/* Static Function Declarations */
-static void mpc8xx_udc_state_transition_up (usb_device_state_t initial,
- usb_device_state_t final);
-static void mpc8xx_udc_state_transition_down (usb_device_state_t initial,
- usb_device_state_t final);
-static void mpc8xx_udc_stall (unsigned int ep);
-static void mpc8xx_udc_flush_tx_fifo (int epid);
-static void mpc8xx_udc_flush_rx_fifo (void);
-static void mpc8xx_udc_clear_rxbd (volatile cbd_t * rx_cbdp);
-static void mpc8xx_udc_init_tx (struct usb_endpoint_instance *epi,
- struct urb *tx_urb);
-static void mpc8xx_udc_dump_request (struct usb_device_request *request);
-static void mpc8xx_udc_clock_init (volatile immap_t * immr,
- volatile cpm8xx_t * cp);
-static int mpc8xx_udc_ep_tx (struct usb_endpoint_instance *epi);
-static int mpc8xx_udc_epn_rx (unsigned int epid, volatile cbd_t * rx_cbdp);
-static void mpc8xx_udc_ep0_rx (volatile cbd_t * rx_cbdp);
-static void mpc8xx_udc_cbd_init (void);
-static void mpc8xx_udc_endpoint_init (void);
-static void mpc8xx_udc_cbd_attach (int ep, uchar tx_size, uchar rx_size);
-static u32 mpc8xx_udc_alloc (u32 data_size, u32 alignment);
-static int mpc8xx_udc_ep0_rx_setup (volatile cbd_t * rx_cbdp);
-static void mpc8xx_udc_set_nak (unsigned int ep);
-static short mpc8xx_udc_handle_txerr (void);
-static void mpc8xx_udc_advance_rx (volatile cbd_t ** rx_cbdp, int epid);
-
-/******************************************************************************
- Global Linkage
- *****************************************************************************/
-
-/* udc_init
- *
- * Do initial bus gluing
- */
-int udc_init (void)
-{
- /* Init various pointers */
- immr = (immap_t *) CONFIG_SYS_IMMR;
- cp = (cpm8xx_t *) & (immr->im_cpm);
- usb_paramp = (usb_pram_t *) & (cp->cp_dparam[PROFF_USB]);
- usbp = (usb_t *) & (cp->cp_scc[0]);
-
- memset (ep_ref, 0x00, (sizeof (struct mpc8xx_ep) * MAX_ENDPOINTS));
-
- udc_device = 0;
- udc_state = STATE_NOT_READY;
-
- usbp->usmod = 0x00;
- usbp->uscom = 0;
-
- /* Set USB Frame #0, Respond at Address & Get a clock source */
- usbp->usaddr = 0x00;
- mpc8xx_udc_clock_init (immr, cp);
-
- /* PA15, PA14 as perhiperal USBRXD and USBOE */
- immr->im_ioport.iop_padir &= ~0x0003;
- immr->im_ioport.iop_papar |= 0x0003;
-
- /* PC11/PC10 as peripheral USBRXP USBRXN */
- immr->im_ioport.iop_pcso |= 0x0030;
-
- /* PC7/PC6 as perhiperal USBTXP and USBTXN */
- immr->im_ioport.iop_pcdir |= 0x0300;
- immr->im_ioport.iop_pcpar |= 0x0300;
-
- /* Set the base address */
- address_base = (u32) (cp->cp_dpmem + CPM_USB_BASE);
-
- /* Initialise endpoints and circular buffers */
- mpc8xx_udc_endpoint_init ();
- mpc8xx_udc_cbd_init ();
-
- /* Assign allocated Dual Port Endpoint descriptors */
- usb_paramp->ep0ptr = (u32) endpoints[0];
- usb_paramp->ep1ptr = (u32) endpoints[1];
- usb_paramp->ep2ptr = (u32) endpoints[2];
- usb_paramp->ep3ptr = (u32) endpoints[3];
- usb_paramp->frame_n = 0;
-
- DBG ("ep0ptr=0x%08x ep1ptr=0x%08x ep2ptr=0x%08x ep3ptr=0x%08x\n",
- usb_paramp->ep0ptr, usb_paramp->ep1ptr, usb_paramp->ep2ptr,
- usb_paramp->ep3ptr);
-
- return 0;
-}
-
-/* udc_irq
- *
- * Poll for whatever events may have occurred
- */
-void udc_irq (void)
-{
- int epid = 0;
- volatile cbd_t *rx_cbdp = 0;
- volatile cbd_t *rx_cbdp_base = 0;
-
- if (udc_state != STATE_READY) {
- return;
- }
-
- if (usbp->usber & USB_E_BSY) {
- /* This shouldn't happen. If it does then it's a bug ! */
- usbp->usber |= USB_E_BSY;
- mpc8xx_udc_flush_rx_fifo ();
- }
-
- /* Scan all RX/Bidirectional Endpoints for RX data. */
- for (epid = 0; epid < MAX_ENDPOINTS; epid++) {
- if (!ep_ref[epid].prx) {
- continue;
- }
- rx_cbdp = rx_cbdp_base = ep_ref[epid].prx;
-
- do {
- if (!(rx_cbdp->cbd_sc & RX_BD_E)) {
-
- if (rx_cbdp->cbd_sc & 0x1F) {
- /* Corrupt data discard it.
- * Controller has NAK'd this packet.
- */
- mpc8xx_udc_clear_rxbd (rx_cbdp);
-
- } else {
- if (!epid) {
- mpc8xx_udc_ep0_rx (rx_cbdp);
-
- } else {
- /* Process data */
- mpc8xx_udc_set_nak (epid);
- mpc8xx_udc_epn_rx (epid, rx_cbdp);
- mpc8xx_udc_clear_rxbd (rx_cbdp);
- }
- }
-
- /* Advance RX CBD pointer */
- mpc8xx_udc_advance_rx (&rx_cbdp, epid);
- ep_ref[epid].prx = rx_cbdp;
- } else {
- /* Advance RX CBD pointer */
- mpc8xx_udc_advance_rx (&rx_cbdp, epid);
- }
-
- } while (rx_cbdp != rx_cbdp_base);
- }
-
- /* Handle TX events as appropiate, the correct place to do this is
- * in a tx routine. Perhaps TX on epn was pre-empted by ep0
- */
-
- if (usbp->usber & USB_E_TXB) {
- usbp->usber |= USB_E_TXB;
- }
-
- if (usbp->usber & (USB_TX_ERRMASK)) {
- mpc8xx_udc_handle_txerr ();
- }
-
- /* Switch to the default state, respond at the default address */
- if (usbp->usber & USB_E_RESET) {
- usbp->usber |= USB_E_RESET;
- usbp->usaddr = 0x00;
- udc_device->device_state = STATE_DEFAULT;
- }
-
- /* if(usbp->usber&USB_E_IDLE){
- We could suspend here !
- usbp->usber|=USB_E_IDLE;
- DBG("idle state change\n");
- }
- if(usbp->usbs){
- We could resume here when IDLE is deasserted !
- Not worth doing, so long as we are self powered though.
- }
- */
-
- return;
-}
-
-/* udc_endpoint_write
- *
- * Write some data to an endpoint
- */
-int udc_endpoint_write (struct usb_endpoint_instance *epi)
-{
- int ep = 0;
- short epid = 1, unnak = 0, ret = 0;
-
- if (udc_state != STATE_READY) {
- ERR ("invalid udc_state != STATE_READY!\n");
- return -1;
- }
-
- if (!udc_device || !epi) {
- return -1;
- }
-
- if (udc_device->device_state != STATE_CONFIGURED) {
- return -1;
- }
-
- ep = epi->endpoint_address & 0x03;
- if (ep >= MAX_ENDPOINTS) {
- return -1;
- }
-
- /* Set NAK for all RX endpoints during TX */
- for (epid = 1; epid < MAX_ENDPOINTS; epid++) {
-
- /* Don't set NAK on DATA IN/CONTROL endpoints */
- if (ep_ref[epid].sc & USB_DIR_IN) {
- continue;
- }
-
- if (!(usbp->usep[epid] & (USEP_THS_NAK | USEP_RHS_NAK))) {
- unnak |= 1 << epid;
- }
-
- mpc8xx_udc_set_nak (epid);
- }
-
- mpc8xx_udc_init_tx (&udc_device->bus->endpoint_array[ep],
- epi->tx_urb);
- ret = mpc8xx_udc_ep_tx (&udc_device->bus->endpoint_array[ep]);
-
- /* Remove temporary NAK */
- for (epid = 1; epid < MAX_ENDPOINTS; epid++) {
- if (unnak & (1 << epid)) {
- udc_unset_nak (epid);
- }
- }
-
- return ret;
-}
-
-/* mpc8xx_udc_assign_urb
- *
- * Associate a given urb to an endpoint TX or RX transmit/receive buffers
- */
-static int mpc8xx_udc_assign_urb (int ep, char direction)
-{
- struct usb_endpoint_instance *epi = 0;
-
- if (ep >= MAX_ENDPOINTS) {
- goto err;
- }
- epi = &udc_device->bus->endpoint_array[ep];
- if (!epi) {
- goto err;
- }
-
- if (!ep_ref[ep].urb) {
- ep_ref[ep].urb = usbd_alloc_urb (udc_device, udc_device->bus->endpoint_array);
- if (!ep_ref[ep].urb) {
- goto err;
- }
- } else {
- ep_ref[ep].urb->actual_length = 0;
- }
-
- switch (direction) {
- case USB_DIR_IN:
- epi->tx_urb = ep_ref[ep].urb;
- break;
- case USB_DIR_OUT:
- epi->rcv_urb = ep_ref[ep].urb;
- break;
- default:
- goto err;
- }
- return 0;
-
- err:
- udc_state = STATE_ERROR;
- return -1;
-}
-
-/* udc_setup_ep
- *
- * Associate U-Boot software endpoints to mpc8xx endpoint parameter ram
- * Isochronous endpoints aren't yet supported!
- */
-void udc_setup_ep (struct usb_device_instance *device, unsigned int ep,
- struct usb_endpoint_instance *epi)
-{
- uchar direction = 0;
- int ep_attrib = 0;
-
- if (epi && (ep < MAX_ENDPOINTS)) {
-
- if (ep == 0) {
- if (epi->rcv_attributes != USB_ENDPOINT_XFER_CONTROL
- || epi->tx_attributes !=
- USB_ENDPOINT_XFER_CONTROL) {
-
- /* ep0 must be a control endpoint */
- udc_state = STATE_ERROR;
- return;
-
- }
- if (!(ep_ref[ep].sc & EP_ATTACHED)) {
- mpc8xx_udc_cbd_attach (ep, epi->tx_packetSize,
- epi->rcv_packetSize);
- }
- usbp->usep[ep] = 0x0000;
- return;
- }
-
- if ((epi->endpoint_address & USB_ENDPOINT_DIR_MASK)
- == USB_DIR_IN) {
-
- direction = 1;
- ep_attrib = epi->tx_attributes;
- epi->rcv_packetSize = 0;
- ep_ref[ep].sc |= USB_DIR_IN;
- } else {
-
- direction = 0;
- ep_attrib = epi->rcv_attributes;
- epi->tx_packetSize = 0;
- ep_ref[ep].sc &= ~USB_DIR_IN;
- }
-
- if (mpc8xx_udc_assign_urb (ep, epi->endpoint_address
- & USB_ENDPOINT_DIR_MASK)) {
- return;
- }
-
- switch (ep_attrib) {
- case USB_ENDPOINT_XFER_CONTROL:
- if (!(ep_ref[ep].sc & EP_ATTACHED)) {
- mpc8xx_udc_cbd_attach (ep,
- epi->tx_packetSize,
- epi->rcv_packetSize);
- }
- usbp->usep[ep] = ep << 12;
- epi->rcv_urb = epi->tx_urb = ep_ref[ep].urb;
-
- break;
- case USB_ENDPOINT_XFER_BULK:
- case USB_ENDPOINT_XFER_INT:
- if (!(ep_ref[ep].sc & EP_ATTACHED)) {
- if (direction) {
- mpc8xx_udc_cbd_attach (ep,
- epi->tx_packetSize,
- 0);
- } else {
- mpc8xx_udc_cbd_attach (ep,
- 0,
- epi->rcv_packetSize);
- }
- }
- usbp->usep[ep] = (ep << 12) | ((ep_attrib) << 8);
-
- break;
- case USB_ENDPOINT_XFER_ISOC:
- default:
- serial_printf ("Error endpoint attrib %d>3\n", ep_attrib);
- udc_state = STATE_ERROR;
- break;
- }
- }
-
-}
-
-/* udc_connect
- *
- * Move state, switch on the USB
- */
-void udc_connect (void)
-{
- /* Enable pull-up resistor on D+
- * TODO: fit a pull-up resistor to drive SE0 for > 2.5us
- */
-
- if (udc_state != STATE_ERROR) {
- udc_state = STATE_READY;
- usbp->usmod |= USMOD_EN;
- }
-}
-
-/* udc_disconnect
- *
- * Disconnect is not used but, is included for completeness
- */
-void udc_disconnect (void)
-{
- /* Disable pull-up resistor on D-
- * TODO: fix a pullup resistor to control this
- */
-
- if (udc_state != STATE_ERROR) {
- udc_state = STATE_NOT_READY;
- }
- usbp->usmod &= ~USMOD_EN;
-}
-
-/* udc_enable
- *
- * Grab an EP0 URB, register interest in a subset of USB events
- */
-void udc_enable (struct usb_device_instance *device)
-{
- if (udc_state == STATE_ERROR) {
- return;
- }
-
- udc_device = device;
-
- if (!ep_ref[0].urb) {
- ep_ref[0].urb = usbd_alloc_urb (device, device->bus->endpoint_array);
- }
-
- /* Register interest in all events except SOF, enable transceiver */
- usbp->usber = 0x03FF;
- usbp->usbmr = 0x02F7;
-
- return;
-}
-
-/* udc_disable
- *
- * disable the currently hooked device
- */
-void udc_disable (void)
-{
- int i = 0;
-
- if (udc_state == STATE_ERROR) {
- DBG ("Won't disable UDC. udc_state==STATE_ERROR !\n");
- return;
- }
-
- udc_device = 0;
-
- for (; i < MAX_ENDPOINTS; i++) {
- if (ep_ref[i].urb) {
- usbd_dealloc_urb (ep_ref[i].urb);
- ep_ref[i].urb = 0;
- }
- }
-
- usbp->usbmr = 0x00;
- usbp->usmod = ~USMOD_EN;
- udc_state = STATE_NOT_READY;
-}
-
-/* udc_startup_events
- *
- * Enable the specified device
- */
-void udc_startup_events (struct usb_device_instance *device)
-{
- udc_enable (device);
- if (udc_state == STATE_READY) {
- usbd_device_event_irq (device, DEVICE_CREATE, 0);
- }
-}
-
-/* udc_set_nak
- *
- * Allow upper layers to signal lower layers should not accept more RX data
- *
- */
-void udc_set_nak (int epid)
-{
- if (epid) {
- mpc8xx_udc_set_nak (epid);
- }
-}
-
-/* udc_unset_nak
- *
- * Suspend sending of NAK tokens for DATA OUT tokens on a given endpoint.
- * Switch off NAKing on this endpoint to accept more data output from host.
- *
- */
-void udc_unset_nak (int epid)
-{
- if (epid > MAX_ENDPOINTS) {
- return;
- }
-
- if (usbp->usep[epid] & (USEP_THS_NAK | USEP_RHS_NAK)) {
- usbp->usep[epid] &= ~(USEP_THS_NAK | USEP_RHS_NAK);
- __asm__ ("eieio");
- }
-}
-
-/******************************************************************************
- Static Linkage
-******************************************************************************/
-
-/* udc_state_transition_up
- * udc_state_transition_down
- *
- * Helper functions to implement device state changes. The device states and
- * the events that transition between them are:
- *
- * STATE_ATTACHED
- * || /\
- * \/ ||
- * DEVICE_HUB_CONFIGURED DEVICE_HUB_RESET
- * || /\
- * \/ ||
- * STATE_POWERED
- * || /\
- * \/ ||
- * DEVICE_RESET DEVICE_POWER_INTERRUPTION
- * || /\
- * \/ ||
- * STATE_DEFAULT
- * || /\
- * \/ ||
- * DEVICE_ADDRESS_ASSIGNED DEVICE_RESET
- * || /\
- * \/ ||
- * STATE_ADDRESSED
- * || /\
- * \/ ||
- * DEVICE_CONFIGURED DEVICE_DE_CONFIGURED
- * || /\
- * \/ ||
- * STATE_CONFIGURED
- *
- * udc_state_transition_up transitions up (in the direction from STATE_ATTACHED
- * to STATE_CONFIGURED) from the specified initial state to the specified final
- * state, passing through each intermediate state on the way. If the initial
- * state is at or above (i.e. nearer to STATE_CONFIGURED) the final state, then
- * no state transitions will take place.
- *
- * udc_state_transition_down transitions down (in the direction from
- * STATE_CONFIGURED to STATE_ATTACHED) from the specified initial state to the
- * specified final state, passing through each intermediate state on the way.
- * If the initial state is at or below (i.e. nearer to STATE_ATTACHED) the final
- * state, then no state transitions will take place.
- *
- */
-
-static void mpc8xx_udc_state_transition_up (usb_device_state_t initial,
- usb_device_state_t final)
-{
- if (initial < final) {
- switch (initial) {
- case STATE_ATTACHED:
- usbd_device_event_irq (udc_device,
- DEVICE_HUB_CONFIGURED, 0);
- if (final == STATE_POWERED)
- break;
- case STATE_POWERED:
- usbd_device_event_irq (udc_device, DEVICE_RESET, 0);
- if (final == STATE_DEFAULT)
- break;
- case STATE_DEFAULT:
- usbd_device_event_irq (udc_device,
- DEVICE_ADDRESS_ASSIGNED, 0);
- if (final == STATE_ADDRESSED)
- break;
- case STATE_ADDRESSED:
- usbd_device_event_irq (udc_device, DEVICE_CONFIGURED,
- 0);
- case STATE_CONFIGURED:
- break;
- default:
- break;
- }
- }
-}
-
-static void mpc8xx_udc_state_transition_down (usb_device_state_t initial,
- usb_device_state_t final)
-{
- if (initial > final) {
- switch (initial) {
- case STATE_CONFIGURED:
- usbd_device_event_irq (udc_device,
- DEVICE_DE_CONFIGURED, 0);
- if (final == STATE_ADDRESSED)
- break;
- case STATE_ADDRESSED:
- usbd_device_event_irq (udc_device, DEVICE_RESET, 0);
- if (final == STATE_DEFAULT)
- break;
- case STATE_DEFAULT:
- usbd_device_event_irq (udc_device,
- DEVICE_POWER_INTERRUPTION, 0);
- if (final == STATE_POWERED)
- break;
- case STATE_POWERED:
- usbd_device_event_irq (udc_device, DEVICE_HUB_RESET,
- 0);
- case STATE_ATTACHED:
- break;
- default:
- break;
- }
- }
-}
-
-/* mpc8xx_udc_stall
- *
- * Force returning of STALL tokens on the given endpoint. Protocol or function
- * STALL conditions are permissable here
- */
-static void mpc8xx_udc_stall (unsigned int ep)
-{
- usbp->usep[ep] |= STALL_BITMASK;
-}
-
-/* mpc8xx_udc_set_nak
- *
- * Force returning of NAK responses for the given endpoint as a kind of very
- * simple flow control
- */
-static void mpc8xx_udc_set_nak (unsigned int ep)
-{
- usbp->usep[ep] |= NAK_BITMASK;
- __asm__ ("eieio");
-}
-
-/* mpc8xx_udc_handle_txerr
- *
- * Handle errors relevant to TX. Return a status code to allow calling
- * indicative of what if anything happened
- */
-static short mpc8xx_udc_handle_txerr ()
-{
- short ep = 0, ret = 0;
-
- for (; ep < TX_RING_SIZE; ep++) {
- if (usbp->usber & (0x10 << ep)) {
-
- /* Timeout or underrun */
- if (tx_cbd[ep]->cbd_sc & 0x06) {
- ret = 1;
- mpc8xx_udc_flush_tx_fifo (ep);
-
- } else {
- if (usbp->usep[ep] & STALL_BITMASK) {
- if (!ep) {
- usbp->usep[ep] &= ~STALL_BITMASK;
- }
- } /* else NAK */
- }
- usbp->usber |= (0x10 << ep);
- }
- }
- return ret;
-}
-
-/* mpc8xx_udc_advance_rx
- *
- * Advance cbd rx
- */
-static void mpc8xx_udc_advance_rx (volatile cbd_t ** rx_cbdp, int epid)
-{
- if ((*rx_cbdp)->cbd_sc & RX_BD_W) {
- *rx_cbdp = (volatile cbd_t *) (endpoints[epid]->rbase + CONFIG_SYS_IMMR);
-
- } else {
- (*rx_cbdp)++;
- }
-}
-
-
-/* mpc8xx_udc_flush_tx_fifo
- *
- * Flush a given TX fifo. Assumes one tx cbd per endpoint
- */
-static void mpc8xx_udc_flush_tx_fifo (int epid)
-{
- volatile cbd_t *tx_cbdp = 0;
-
- if (epid > MAX_ENDPOINTS) {
- return;
- }
-
- /* TX stop */
- immr->im_cpm.cp_cpcr = ((epid << 2) | 0x1D01);
- __asm__ ("eieio");
- while (immr->im_cpm.cp_cpcr & 0x01);
-
- usbp->uscom = 0x40 | 0;
-
- /* reset ring */
- tx_cbdp = (cbd_t *) (endpoints[epid]->tbptr + CONFIG_SYS_IMMR);
- tx_cbdp->cbd_sc = (TX_BD_I | TX_BD_W);
-
-
- endpoints[epid]->tptr = endpoints[epid]->tbase;
- endpoints[epid]->tstate = 0x00;
- endpoints[epid]->tbcnt = 0x00;
-
- /* TX start */
- immr->im_cpm.cp_cpcr = ((epid << 2) | 0x2D01);
- __asm__ ("eieio");
- while (immr->im_cpm.cp_cpcr & 0x01);
-
- return;
-}
-
-/* mpc8xx_udc_flush_rx_fifo
- *
- * For the sake of completeness of the namespace, it seems like
- * a good-design-decision (tm) to include mpc8xx_udc_flush_rx_fifo();
- * If RX_BD_E is true => a driver bug either here or in an upper layer
- * not polling frequently enough. If RX_BD_E is true we have told the host
- * we have accepted data but, the CPM found it had no-where to put that data
- * which needless to say would be a bad thing.
- */
-static void mpc8xx_udc_flush_rx_fifo ()
-{
- int i = 0;
-
- for (i = 0; i < RX_RING_SIZE; i++) {
- if (!(rx_cbd[i]->cbd_sc & RX_BD_E)) {
- ERR ("buf %p used rx data len = 0x%x sc=0x%x!\n",
- rx_cbd[i], rx_cbd[i]->cbd_datlen,
- rx_cbd[i]->cbd_sc);
-
- }
- }
- ERR ("BUG : Input over-run\n");
-}
-
-/* mpc8xx_udc_clear_rxbd
- *
- * Release control of RX CBD to CP.
- */
-static void mpc8xx_udc_clear_rxbd (volatile cbd_t * rx_cbdp)
-{
- rx_cbdp->cbd_datlen = 0x0000;
- rx_cbdp->cbd_sc = ((rx_cbdp->cbd_sc & RX_BD_W) | (RX_BD_E | RX_BD_I));
- __asm__ ("eieio");
-}
-
-/* mpc8xx_udc_tx_irq
- *
- * Parse for tx timeout, control RX or USB reset/busy conditions
- * Return -1 on timeout, -2 on fatal error, else return zero
- */
-static int mpc8xx_udc_tx_irq (int ep)
-{
- int i = 0;
-
- if (usbp->usber & (USB_TX_ERRMASK)) {
- if (mpc8xx_udc_handle_txerr ()) {
- /* Timeout, controlling function must retry send */
- return -1;
- }
- }
-
- if (usbp->usber & (USB_E_RESET | USB_E_BSY)) {
- /* Fatal, abandon TX transaction */
- return -2;
- }
-
- if (usbp->usber & USB_E_RXB) {
- for (i = 0; i < RX_RING_SIZE; i++) {
- if (!(rx_cbd[i]->cbd_sc & RX_BD_E)) {
- if ((rx_cbd[i] == ep_ref[0].prx) || ep) {
- return -2;
- }
- }
- }
- }
-
- return 0;
-}
-
-/* mpc8xx_udc_ep_tx
- *
- * Transmit in a re-entrant fashion outbound USB packets.
- * Implement retry/timeout mechanism described in USB specification
- * Toggle DATA0/DATA1 pids as necessary
- * Introduces non-standard tx_retry. The USB standard has no scope for slave
- * devices to give up TX, however tx_retry stops us getting stuck in an endless
- * TX loop.
- */
-static int mpc8xx_udc_ep_tx (struct usb_endpoint_instance *epi)
-{
- struct urb *urb = epi->tx_urb;
- volatile cbd_t *tx_cbdp = 0;
- unsigned int ep = 0, pkt_len = 0, x = 0, tx_retry = 0;
- int ret = 0;
-
- if (!epi || (epi->endpoint_address & 0x03) >= MAX_ENDPOINTS || !urb) {
- return -1;
- }
-
- ep = epi->endpoint_address & 0x03;
- tx_cbdp = (cbd_t *) (endpoints[ep]->tbptr + CONFIG_SYS_IMMR);
-
- if (tx_cbdp->cbd_sc & TX_BD_R || usbp->usber & USB_E_TXB) {
- mpc8xx_udc_flush_tx_fifo (ep);
- usbp->usber |= USB_E_TXB;
- };
-
- while (tx_retry++ < 100) {
- ret = mpc8xx_udc_tx_irq (ep);
- if (ret == -1) {
- /* ignore timeout here */
- } else if (ret == -2) {
- /* Abandon TX */
- mpc8xx_udc_flush_tx_fifo (ep);
- return -1;
- }
-
- tx_cbdp = (cbd_t *) (endpoints[ep]->tbptr + CONFIG_SYS_IMMR);
- while (tx_cbdp->cbd_sc & TX_BD_R) {
- };
- tx_cbdp->cbd_sc = (tx_cbdp->cbd_sc & TX_BD_W);
-
- pkt_len = urb->actual_length - epi->sent;
-
- if (pkt_len > epi->tx_packetSize || pkt_len > EP_MAX_PKT) {
- pkt_len = min(epi->tx_packetSize, EP_MAX_PKT);
- }
-
- for (x = 0; x < pkt_len; x++) {
- *((unsigned char *) (tx_cbdp->cbd_bufaddr + x)) =
- urb->buffer[epi->sent + x];
- }
- tx_cbdp->cbd_datlen = pkt_len;
- tx_cbdp->cbd_sc |= (CBD_TX_BITMASK | ep_ref[ep].pid);
- __asm__ ("eieio");
-
-#ifdef __SIMULATE_ERROR__
- if (++err_poison_test == 2) {
- err_poison_test = 0;
- tx_cbdp->cbd_sc &= ~TX_BD_TC;
- }
-#endif
-
- usbp->uscom = (USCOM_STR | ep);
-
- while (!(usbp->usber & USB_E_TXB)) {
- ret = mpc8xx_udc_tx_irq (ep);
- if (ret == -1) {
- /* TX timeout */
- break;
- } else if (ret == -2) {
- if (usbp->usber & USB_E_TXB) {
- usbp->usber |= USB_E_TXB;
- }
- mpc8xx_udc_flush_tx_fifo (ep);
- return -1;
- }
- };
-
- if (usbp->usber & USB_E_TXB) {
- usbp->usber |= USB_E_TXB;
- }
-
- /* ACK must be present <= 18bit times from TX */
- if (ret == -1) {
- continue;
- }
-
- /* TX ACK : USB 2.0 8.7.2, Toggle PID, Advance TX */
- epi->sent += pkt_len;
- epi->last = min(urb->actual_length - epi->sent, epi->tx_packetSize);
- TOGGLE_TX_PID (ep_ref[ep].pid);
-
- if (epi->sent >= epi->tx_urb->actual_length) {
-
- epi->tx_urb->actual_length = 0;
- epi->sent = 0;
-
- if (ep_ref[ep].sc & EP_SEND_ZLP) {
- ep_ref[ep].sc &= ~EP_SEND_ZLP;
- } else {
- return 0;
- }
- }
- }
-
- ERR ("TX fail, endpoint 0x%x tx bytes 0x%x/0x%x\n", ep, epi->sent,
- epi->tx_urb->actual_length);
-
- return -1;
-}
-
-/* mpc8xx_udc_dump_request
- *
- * Dump a control request to console
- */
-static void mpc8xx_udc_dump_request (struct usb_device_request *request)
-{
- DBG ("bmRequestType:%02x bRequest:%02x wValue:%04x "
- "wIndex:%04x wLength:%04x ?\n",
- request->bmRequestType,
- request->bRequest,
- request->wValue, request->wIndex, request->wLength);
-
- return;
-}
-
-/* mpc8xx_udc_ep0_rx_setup
- *
- * Decode received ep0 SETUP packet. return non-zero on error
- */
-static int mpc8xx_udc_ep0_rx_setup (volatile cbd_t * rx_cbdp)
-{
- unsigned int x = 0;
- struct urb *purb = ep_ref[0].urb;
- struct usb_endpoint_instance *epi =
- &udc_device->bus->endpoint_array[0];
-
- for (; x < rx_cbdp->cbd_datlen; x++) {
- *(((unsigned char *) &ep_ref[0].urb->device_request) + x) =
- *((unsigned char *) (rx_cbdp->cbd_bufaddr + x));
- }
-
- mpc8xx_udc_clear_rxbd (rx_cbdp);
-
- if (ep0_recv_setup (purb)) {
- mpc8xx_udc_dump_request (&purb->device_request);
- return -1;
- }
-
- if ((purb->device_request.bmRequestType & USB_REQ_DIRECTION_MASK)
- == USB_REQ_HOST2DEVICE) {
-
- switch (purb->device_request.bRequest) {
- case USB_REQ_SET_ADDRESS:
- /* Send the Status OUT ZLP */
- ep_ref[0].pid = TX_BD_PID_DATA1;
- purb->actual_length = 0;
- mpc8xx_udc_init_tx (epi, purb);
- mpc8xx_udc_ep_tx (epi);
-
- /* Move to the addressed state */
- usbp->usaddr = udc_device->address;
- mpc8xx_udc_state_transition_up (udc_device->device_state,
- STATE_ADDRESSED);
- return 0;
-
- case USB_REQ_SET_CONFIGURATION:
- if (!purb->device_request.wValue) {
- /* Respond at default address */
- usbp->usaddr = 0x00;
- mpc8xx_udc_state_transition_down (udc_device->device_state,
- STATE_ADDRESSED);
- } else {
- /* TODO: Support multiple configurations */
- mpc8xx_udc_state_transition_up (udc_device->device_state,
- STATE_CONFIGURED);
- for (x = 1; x < MAX_ENDPOINTS; x++) {
- if ((udc_device->bus->endpoint_array[x].endpoint_address & USB_ENDPOINT_DIR_MASK)
- == USB_DIR_IN) {
- ep_ref[x].pid = TX_BD_PID_DATA0;
- } else {
- ep_ref[x].pid = RX_BD_PID_DATA0;
- }
- /* Set configuration must unstall endpoints */
- usbp->usep[x] &= ~STALL_BITMASK;
- }
- }
- break;
- default:
- /* CDC/Vendor specific */
- break;
- }
-
- /* Send ZLP as ACK in Status OUT phase */
- ep_ref[0].pid = TX_BD_PID_DATA1;
- purb->actual_length = 0;
- mpc8xx_udc_init_tx (epi, purb);
- mpc8xx_udc_ep_tx (epi);
-
- } else {
-
- if (purb->actual_length) {
- ep_ref[0].pid = TX_BD_PID_DATA1;
- mpc8xx_udc_init_tx (epi, purb);
-
- if (!(purb->actual_length % EP0_MAX_PACKET_SIZE)) {
- ep_ref[0].sc |= EP_SEND_ZLP;
- }
-
- if (purb->device_request.wValue ==
- USB_DESCRIPTOR_TYPE_DEVICE) {
- if (le16_to_cpu (purb->device_request.wLength)
- > purb->actual_length) {
- /* Send EP0_MAX_PACKET_SIZE bytes
- * unless correct size requested.
- */
- if (purb->actual_length > epi->tx_packetSize) {
- purb->actual_length = epi->tx_packetSize;
- }
- }
- }
- mpc8xx_udc_ep_tx (epi);
-
- } else {
- /* Corrupt SETUP packet? */
- ERR ("Zero length data or SETUP with DATA-IN phase ?\n");
- return 1;
- }
- }
- return 0;
-}
-
-/* mpc8xx_udc_init_tx
- *
- * Setup some basic parameters for a TX transaction
- */
-static void mpc8xx_udc_init_tx (struct usb_endpoint_instance *epi,
- struct urb *tx_urb)
-{
- epi->sent = 0;
- epi->last = 0;
- epi->tx_urb = tx_urb;
-}
-
-/* mpc8xx_udc_ep0_rx
- *
- * Receive ep0/control USB data. Parse and possibly send a response.
- */
-static void mpc8xx_udc_ep0_rx (volatile cbd_t * rx_cbdp)
-{
- if (rx_cbdp->cbd_sc & RX_BD_PID_SETUP) {
-
- /* Unconditionally accept SETUP packets */
- if (mpc8xx_udc_ep0_rx_setup (rx_cbdp)) {
- mpc8xx_udc_stall (0);
- }
-
- } else {
-
- mpc8xx_udc_clear_rxbd (rx_cbdp);
-
- if ((rx_cbdp->cbd_datlen - 2)) {
- /* SETUP with a DATA phase
- * outside of SETUP packet.
- * Reply with STALL.
- */
- mpc8xx_udc_stall (0);
- }
- }
-}
-
-/* mpc8xx_udc_epn_rx
- *
- * Receive some data from cbd into USB system urb data abstraction
- * Upper layers should NAK if there is insufficient RX data space
- */
-static int mpc8xx_udc_epn_rx (unsigned int epid, volatile cbd_t * rx_cbdp)
-{
- struct usb_endpoint_instance *epi = 0;
- struct urb *urb = 0;
- unsigned int x = 0;
-
- if (epid >= MAX_ENDPOINTS || !rx_cbdp->cbd_datlen) {
- return 0;
- }
-
- /* USB 2.0 PDF section 8.6.4
- * Discard data with invalid PID it is a resend.
- */
- if (ep_ref[epid].pid != (rx_cbdp->cbd_sc & 0xC0)) {
- return 1;
- }
- TOGGLE_RX_PID (ep_ref[epid].pid);
-
- epi = &udc_device->bus->endpoint_array[epid];
- urb = epi->rcv_urb;
-
- for (; x < (rx_cbdp->cbd_datlen - 2); x++) {
- *((unsigned char *) (urb->buffer + urb->actual_length + x)) =
- *((unsigned char *) (rx_cbdp->cbd_bufaddr + x));
- }
-
- if (x) {
- usbd_rcv_complete (epi, x, 0);
- if (ep_ref[epid].urb->status == RECV_ERROR) {
- DBG ("RX error unset NAK\n");
- udc_unset_nak (epid);
- }
- }
- return x;
-}
-
-/* mpc8xx_udc_clock_init
- *
- * Obtain a clock reference for Full Speed Signaling
- */
-static void mpc8xx_udc_clock_init (volatile immap_t * immr,
- volatile cpm8xx_t * cp)
-{
-
-#if defined(CONFIG_SYS_USB_EXTC_CLK)
-
- /* This has been tested with a 48MHz crystal on CLK6 */
- switch (CONFIG_SYS_USB_EXTC_CLK) {
- case 1:
- immr->im_ioport.iop_papar |= 0x0100;
- immr->im_ioport.iop_padir &= ~0x0100;
- cp->cp_sicr |= 0x24;
- break;
- case 2:
- immr->im_ioport.iop_papar |= 0x0200;
- immr->im_ioport.iop_padir &= ~0x0200;
- cp->cp_sicr |= 0x2D;
- break;
- case 3:
- immr->im_ioport.iop_papar |= 0x0400;
- immr->im_ioport.iop_padir &= ~0x0400;
- cp->cp_sicr |= 0x36;
- break;
- case 4:
- immr->im_ioport.iop_papar |= 0x0800;
- immr->im_ioport.iop_padir &= ~0x0800;
- cp->cp_sicr |= 0x3F;
- break;
- default:
- udc_state = STATE_ERROR;
- break;
- }
-
-#elif defined(CONFIG_SYS_USB_BRGCLK)
-
- /* This has been tested with brgclk == 50MHz */
- int divisor = 0;
-
- if (gd->cpu_clk < 48000000L) {
- ERR ("brgclk is too slow for full-speed USB!\n");
- udc_state = STATE_ERROR;
- return;
- }
-
- /* Assume the brgclk is 'good enough', we want !(gd->cpu_clk%48MHz)
- * but, can /probably/ live with close-ish alternative rates.
- */
- divisor = (gd->cpu_clk / 48000000L) - 1;
- cp->cp_sicr &= ~0x0000003F;
-
- switch (CONFIG_SYS_USB_BRGCLK) {
- case 1:
- cp->cp_brgc1 |= (divisor | CPM_BRG_EN);
- cp->cp_sicr &= ~0x2F;
- break;
- case 2:
- cp->cp_brgc2 |= (divisor | CPM_BRG_EN);
- cp->cp_sicr |= 0x00000009;
- break;
- case 3:
- cp->cp_brgc3 |= (divisor | CPM_BRG_EN);
- cp->cp_sicr |= 0x00000012;
- break;
- case 4:
- cp->cp_brgc4 = (divisor | CPM_BRG_EN);
- cp->cp_sicr |= 0x0000001B;
- break;
- default:
- udc_state = STATE_ERROR;
- break;
- }
-
-#else
-#error "CONFIG_SYS_USB_EXTC_CLK or CONFIG_SYS_USB_BRGCLK must be defined"
-#endif
-
-}
-
-/* mpc8xx_udc_cbd_attach
- *
- * attach a cbd to and endpoint
- */
-static void mpc8xx_udc_cbd_attach (int ep, uchar tx_size, uchar rx_size)
-{
-
- if (!tx_cbd[ep] || !rx_cbd[ep] || ep >= MAX_ENDPOINTS) {
- udc_state = STATE_ERROR;
- return;
- }
-
- if (tx_size > USB_MAX_PKT || rx_size > USB_MAX_PKT ||
- (!tx_size && !rx_size)) {
- udc_state = STATE_ERROR;
- return;
- }
-
- /* Attach CBD to appropiate Parameter RAM Endpoint data structure */
- if (rx_size) {
- endpoints[ep]->rbase = (u32) rx_cbd[rx_ct];
- endpoints[ep]->rbptr = (u32) rx_cbd[rx_ct];
- rx_ct++;
-
- if (!ep) {
-
- endpoints[ep]->rbptr = (u32) rx_cbd[rx_ct];
- rx_cbd[rx_ct]->cbd_sc |= RX_BD_W;
- rx_ct++;
-
- } else {
- rx_ct += 2;
- endpoints[ep]->rbptr = (u32) rx_cbd[rx_ct];
- rx_cbd[rx_ct]->cbd_sc |= RX_BD_W;
- rx_ct++;
- }
-
- /* Where we expect to RX data on this endpoint */
- ep_ref[ep].prx = rx_cbd[rx_ct - 1];
- } else {
-
- ep_ref[ep].prx = 0;
- endpoints[ep]->rbase = 0;
- endpoints[ep]->rbptr = 0;
- }
-
- if (tx_size) {
- endpoints[ep]->tbase = (u32) tx_cbd[tx_ct];
- endpoints[ep]->tbptr = (u32) tx_cbd[tx_ct];
- tx_ct++;
- } else {
- endpoints[ep]->tbase = 0;
- endpoints[ep]->tbptr = 0;
- }
-
- endpoints[ep]->tstate = 0;
- endpoints[ep]->tbcnt = 0;
- endpoints[ep]->mrblr = EP_MAX_PKT;
- endpoints[ep]->rfcr = 0x18;
- endpoints[ep]->tfcr = 0x18;
- ep_ref[ep].sc |= EP_ATTACHED;
-
- DBG ("ep %d rbase 0x%08x rbptr 0x%08x tbase 0x%08x tbptr 0x%08x prx = %p\n",
- ep, endpoints[ep]->rbase, endpoints[ep]->rbptr,
- endpoints[ep]->tbase, endpoints[ep]->tbptr,
- ep_ref[ep].prx);
-
- return;
-}
-
-/* mpc8xx_udc_cbd_init
- *
- * Allocate space for a cbd and allocate TX/RX data space
- */
-static void mpc8xx_udc_cbd_init (void)
-{
- int i = 0;
-
- for (; i < TX_RING_SIZE; i++) {
- tx_cbd[i] = (cbd_t *)
- mpc8xx_udc_alloc (sizeof (cbd_t), sizeof (int));
- }
-
- for (i = 0; i < RX_RING_SIZE; i++) {
- rx_cbd[i] = (cbd_t *)
- mpc8xx_udc_alloc (sizeof (cbd_t), sizeof (int));
- }
-
- for (i = 0; i < TX_RING_SIZE; i++) {
- tx_cbd[i]->cbd_bufaddr =
- mpc8xx_udc_alloc (EP_MAX_PKT, sizeof (int));
-
- tx_cbd[i]->cbd_sc = (TX_BD_I | TX_BD_W);
- tx_cbd[i]->cbd_datlen = 0x0000;
- }
-
-
- for (i = 0; i < RX_RING_SIZE; i++) {
- rx_cbd[i]->cbd_bufaddr =
- mpc8xx_udc_alloc (EP_MAX_PKT, sizeof (int));
- rx_cbd[i]->cbd_sc = (RX_BD_I | RX_BD_E);
- rx_cbd[i]->cbd_datlen = 0x0000;
-
- }
-
- return;
-}
-
-/* mpc8xx_udc_endpoint_init
- *
- * Attach an endpoint to some dpram
- */
-static void mpc8xx_udc_endpoint_init (void)
-{
- int i = 0;
-
- for (; i < MAX_ENDPOINTS; i++) {
- endpoints[i] = (usb_epb_t *)
- mpc8xx_udc_alloc (sizeof (usb_epb_t), 32);
- }
-}
-
-/* mpc8xx_udc_alloc
- *
- * Grab the address of some dpram
- */
-static u32 mpc8xx_udc_alloc (u32 data_size, u32 alignment)
-{
- u32 retaddr = address_base;
-
- while (retaddr % alignment) {
- retaddr++;
- }
- address_base += data_size;
-
- return retaddr;
-}
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 58f5de5200100a759ec77b7f5748b8a31c59ca1e..ac5371f2aecc1535ec51d9d8efc5cb37f340bab9 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -29,7 +29,6 @@ obj-$(CONFIG_CFB_CONSOLE) += cfb_console.o
obj-$(CONFIG_FSL_DIU_FB) += fsl_diu_fb.o videomodes.o
obj-$(CONFIG_VIDEO_FSL_DCU_FB) += fsl_dcu_fb.o videomodes.o
obj-$(CONFIG_L5F31188) += l5f31188.o
-obj-$(CONFIG_MPC8XX_LCD) += mpc8xx_lcd.o
obj-$(CONFIG_PXA_LCD) += pxa_lcd.o
obj-$(CONFIG_SCF0403_LCD) += scf0403_lcd.o
obj-$(CONFIG_S6E8AX0) += s6e8ax0.o
diff --git a/drivers/video/mpc8xx_lcd.c b/drivers/video/mpc8xx_lcd.c
deleted file mode 100644
index b08576eab203f3ef6a6f6ab4ab348128fdff38da..0000000000000000000000000000000000000000
--- a/drivers/video/mpc8xx_lcd.c
+++ /dev/null
@@ -1,400 +0,0 @@
-/*
- * (C) Copyright 2001-2002
- * Wolfgang Denk, DENX Software Engineering -- wd@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/************************************************************************/
-/* ** HEADER FILES */
-/************************************************************************/
-
-/* #define DEBUG */
-
-#include <config.h>
-#include <common.h>
-#include <command.h>
-#include <watchdog.h>
-#include <stdarg.h>
-#include <lcdvideo.h>
-#include <linux/types.h>
-#include <stdio_dev.h>
-#if defined(CONFIG_POST)
-#include <post.h>
-#endif
-#include <lcd.h>
-
-#ifdef CONFIG_LCD
-
-/************************************************************************/
-/* ** CONFIG STUFF -- should be moved to board config file */
-/************************************************************************/
-#ifndef CONFIG_LCD_INFO
-#define CONFIG_LCD_INFO /* Display Logo, (C) and system info */
-#endif
-
-/*----------------------------------------------------------------------*/
-#ifdef CONFIG_KYOCERA_KCS057QV1AJ
-/*
- * Kyocera KCS057QV1AJ-G23. Passive, color, single scan.
- */
-#define LCD_BPP LCD_COLOR4
-
-vidinfo_t panel_info = {
- 640, 480, 132, 99, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH,
- LCD_BPP, 1, 0, 1, 0, 5, 0, 0, 0
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_KYOCERA_KCS057QV1AJ */
-/*----------------------------------------------------------------------*/
-
-/*----------------------------------------------------------------------*/
-#ifdef CONFIG_HITACHI_SP19X001_Z1A
-/*
- * Hitachi SP19X001-. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 154, 116, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH,
- LCD_COLOR8, 1, 0, 1, 0, 0, 0, 0, 0
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_HITACHI_SP19X001_Z1A */
-/*----------------------------------------------------------------------*/
-
-/*----------------------------------------------------------------------*/
-#ifdef CONFIG_NEC_NL6448AC33
-/*
- * NEC NL6448AC33-18. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 132, 99, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 144, 2, 0, 33
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_NEC_NL6448AC33 */
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_NEC_NL6448BC20
-/*
- * NEC NL6448BC20-08. 6.5", 640x480. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 132, 99, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 144, 2, 0, 33
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_NEC_NL6448BC20 */
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_NEC_NL6448BC33_54
-/*
- * NEC NL6448BC33-54. 10.4", 640x480. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 212, 158, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 144, 2, 0, 33
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_NEC_NL6448BC33_54 */
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_SHARP_LQ104V7DS01
-/*
- * SHARP LQ104V7DS01. 6.5", 640x480. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 132, 99, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_LOW,
- 3, 0, 0, 1, 1, 25, 1, 0, 33
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_SHARP_LQ104V7DS01 */
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_SHARP_16x9
-/*
- * Sharp 320x240. Active, color, single scan. It isn't 16x9, and I am
- * not sure what it is.......
- */
-vidinfo_t panel_info = {
- 320, 240, 0, 0, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 15, 4, 0, 3
-};
-#endif /* CONFIG_SHARP_16x9 */
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_SHARP_LQ057Q3DC02
-/*
- * Sharp LQ057Q3DC02 display. Active, color, single scan.
- */
-#undef LCD_DF
-#define LCD_DF 12
-
-vidinfo_t panel_info = {
- 320, 240, 0, 0, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 15, 4, 0, 3
- /* wbl, vpw, lcdac, wbf */
-};
-#define CONFIG_LCD_INFO_BELOW_LOGO
-#endif /* CONFIG_SHARP_LQ057Q3DC02 */
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_SHARP_LQ64D341
-/*
- * Sharp LQ64D341 display, 640x480. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 0, 0, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 128, 16, 0, 32
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_SHARP_LQ64D341 */
-
-#ifdef CONFIG_SHARP_LQ065T9DR51U
-/*
- * Sharp LQ065T9DR51U display, 400x240. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 400, 240, 143, 79, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 248, 4, 0, 35
- /* wbl, vpw, lcdac, wbf */
-};
-#define CONFIG_LCD_INFO_BELOW_LOGO
-#endif /* CONFIG_SHARP_LQ065T9DR51U */
-
-#ifdef CONFIG_SHARP_LQ084V1DG21
-/*
- * Sharp LQ084V1DG21 display, 640x480. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 171, 129, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_LOW,
- 3, 0, 0, 1, 1, 160, 3, 0, 48
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_SHARP_LQ084V1DG21 */
-
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_HLD1045
-/*
- * HLD1045 display, 640x480. Active, color, single scan.
- */
-vidinfo_t panel_info = {
- 640, 480, 0, 0, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 160, 3, 0, 48
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_HLD1045 */
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_PRIMEVIEW_V16C6448AC
-/*
- * Prime View V16C6448AC
- */
-vidinfo_t panel_info = {
- 640, 480, 130, 98, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW, CONFIG_SYS_LOW, CONFIG_SYS_HIGH,
- 3, 0, 0, 1, 1, 144, 2, 0, 35
- /* wbl, vpw, lcdac, wbf */
-};
-#endif /* CONFIG_PRIMEVIEW_V16C6448AC */
-
-/*----------------------------------------------------------------------*/
-
-#ifdef CONFIG_OPTREX_BW
-/*
- * Optrex CBL50840-2 NF-FW 99 22 M5
- * or
- * Hitachi LMG6912RPFC-00T
- * or
- * Hitachi SP14Q002
- *
- * 320x240. Black & white.
- */
-#define OPTREX_BPP 0 /* 0 - monochrome, 1 bpp */
- /* 1 - 4 grey levels, 2 bpp */
- /* 2 - 16 grey levels, 4 bpp */
-vidinfo_t panel_info = {
- 320, 240, 0, 0, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_HIGH, CONFIG_SYS_LOW,
- OPTREX_BPP, 0, 0, 0, 0, 0, 0, 0, 0, 4
-};
-#endif /* CONFIG_OPTREX_BW */
-
-/************************************************************************/
-/* ----------------- chipset specific functions ----------------------- */
-/************************************************************************/
-
-/*
- * Calculate fb size for VIDEOLFB_ATAG.
- */
-ulong calc_fbsize (void)
-{
- ulong size;
- int line_length = (panel_info.vl_col * NBITS (panel_info.vl_bpix)) / 8;
-
- size = line_length * panel_info.vl_row;
-
- return size;
-}
-
-void lcd_ctrl_init (void *lcdbase)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile lcd823_t *lcdp = &immr->im_lcd;
-
- uint lccrtmp;
- uint lchcr_hpc_tmp;
-
- /* Initialize the LCD control register according to the LCD
- * parameters defined. We do everything here but enable
- * the controller.
- */
-
- lccrtmp = LCDBIT (LCCR_BNUM_BIT,
- (((panel_info.vl_row * panel_info.vl_col) * (1 << LCD_BPP)) / 128));
-
- lccrtmp |= LCDBIT (LCCR_CLKP_BIT, panel_info.vl_clkp) |
- LCDBIT (LCCR_OEP_BIT, panel_info.vl_oep) |
- LCDBIT (LCCR_HSP_BIT, panel_info.vl_hsp) |
- LCDBIT (LCCR_VSP_BIT, panel_info.vl_vsp) |
- LCDBIT (LCCR_DP_BIT, panel_info.vl_dp) |
- LCDBIT (LCCR_BPIX_BIT, panel_info.vl_bpix) |
- LCDBIT (LCCR_LBW_BIT, panel_info.vl_lbw) |
- LCDBIT (LCCR_SPLT_BIT, panel_info.vl_splt) |
- LCDBIT (LCCR_CLOR_BIT, panel_info.vl_clor) |
- LCDBIT (LCCR_TFT_BIT, panel_info.vl_tft);
-
-#if 0
- lccrtmp |= ((SIU_LEVEL5 / 2) << 12);
- lccrtmp |= LCCR_EIEN;
-#endif
-
- lcdp->lcd_lccr = lccrtmp;
- lcdp->lcd_lcsr = 0xFF; /* Clear pending interrupts */
-
- /* Initialize LCD controller bus priorities.
- */
- immr->im_siu_conf.sc_sdcr &= ~0x0f; /* RAID = LAID = 0 */
-
- /* set SHFT/CLOCK division factor 4
- * This needs to be set based upon display type and processor
- * speed. The TFT displays run about 20 to 30 MHz.
- * I was running 64 MHz processor speed.
- * The value for this divider must be chosen so the result is
- * an integer of the processor speed (i.e., divide by 3 with
- * 64 MHz would be bad).
- */
- immr->im_clkrst.car_sccr &= ~0x1F;
- immr->im_clkrst.car_sccr |= LCD_DF; /* was 8 */
-
- /* Enable LCD on port D.
- */
- immr->im_ioport.iop_pdpar |= 0x1FFF;
- immr->im_ioport.iop_pddir |= 0x1FFF;
-
- /* Enable LCD_A/B/C on port B.
- */
- immr->im_cpm.cp_pbpar |= 0x00005001;
- immr->im_cpm.cp_pbdir |= 0x00005001;
-
- /* Load the physical address of the linear frame buffer
- * into the LCD controller.
- * BIG NOTE: This has to be modified to load A and B depending
- * upon the split mode of the LCD.
- */
- lcdp->lcd_lcfaa = (ulong)lcdbase;
- lcdp->lcd_lcfba = (ulong)lcdbase;
-
- /* MORE HACKS...This must be updated according to 823 manual
- * for different panels.
- * Udi Finkelstein - done - see below:
- * Note: You better not try unsupported combinations such as
- * 4-bit wide passive dual scan LCD at 4/8 Bit color.
- */
- lchcr_hpc_tmp =
- (panel_info.vl_col *
- (panel_info.vl_tft ? 8 :
- (((2 - panel_info.vl_lbw) << /* 4 bit=2, 8-bit = 1 */
- /* use << to mult by: single scan = 1, dual scan = 2 */
- panel_info.vl_splt) *
- (panel_info.vl_bpix | 1)))) >> 3; /* 2/4 BPP = 1, 8/16 BPP = 3 */
-
- lcdp->lcd_lchcr = LCHCR_BO |
- LCDBIT (LCHCR_AT_BIT, 4) |
- LCDBIT (LCHCR_HPC_BIT, lchcr_hpc_tmp) |
- panel_info.vl_wbl;
-
- lcdp->lcd_lcvcr = LCDBIT (LCVCR_VPW_BIT, panel_info.vl_vpw) |
- LCDBIT (LCVCR_LCD_AC_BIT, panel_info.vl_lcdac) |
- LCDBIT (LCVCR_VPC_BIT, panel_info.vl_row) |
- panel_info.vl_wbf;
-
-}
-
-/*----------------------------------------------------------------------*/
-
-#if LCD_BPP == LCD_COLOR8
-void
-lcd_setcolreg (ushort regno, ushort red, ushort green, ushort blue)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(immr->im_cpm);
- unsigned short colreg, *cmap_ptr;
-
- cmap_ptr = (unsigned short *)&cp->lcd_cmap[regno * 2];
-
- colreg = ((red & 0x0F) << 8) |
- ((green & 0x0F) << 4) |
- (blue & 0x0F) ;
-
- *cmap_ptr = colreg;
-
- debug ("setcolreg: reg %2d @ %p: R=%02X G=%02X B=%02X => %02X%02X\n",
- regno, &(cp->lcd_cmap[regno * 2]),
- red, green, blue,
- cp->lcd_cmap[ regno * 2 ], cp->lcd_cmap[(regno * 2) + 1]);
-}
-#endif /* LCD_COLOR8 */
-
-/*----------------------------------------------------------------------*/
-
-ushort *configuration_get_cmap(void)
-{
- immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- cpm8xx_t *cp = &(immr->im_cpm);
- return (ushort *)&(cp->lcd_cmap[255 * sizeof(ushort)]);
-}
-
-#if defined(CONFIG_MPC823)
-void fb_put_byte(uchar **fb, uchar **from)
-{
- *(*fb)++ = (255 - *(*from)++);
-}
-#endif
-
-#ifdef CONFIG_LCD_LOGO
-#include <bmp_logo.h>
-void lcd_logo_set_cmap(void)
-{
- int i;
- ushort *cmap;
- immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- cpm8xx_t *cp = &(immr->im_cpm);
- cmap = (ushort *)&(cp->lcd_cmap[BMP_LOGO_OFFSET * sizeof(ushort)]);
-
- for (i = 0; i < BMP_LOGO_COLORS; ++i)
- *cmap++ = bmp_logo_palette[i];
-}
-#endif
-
-void lcd_enable (void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile lcd823_t *lcdp = &immr->im_lcd;
-
- /* Enable the LCD panel */
- immr->im_siu_conf.sc_sdcr |= (1 << (31 - 25)); /* LAM = 1 */
- lcdp->lcd_lccr |= LCCR_PON;
-}
-
-/************************************************************************/
-
-#endif /* CONFIG_LCD */
diff --git a/examples/standalone/Makefile b/examples/standalone/Makefile
index 5a6ae0013c1db3963e73cd6b54bed9d0f21767e0..4c25f6f48f9e4c018c00dc15f4edeaa820d3d0f2 100644
--- a/examples/standalone/Makefile
+++ b/examples/standalone/Makefile
@@ -10,7 +10,6 @@ extra-$(CONFIG_SMC91111) += smc91111_eeprom
extra-$(CONFIG_SMC911X) += smc911x_eeprom
extra-$(CONFIG_SPI_FLASH_ATMEL) += atmel_df_pow2
extra-$(CONFIG_MPC5xxx) += interrupt
-extra-$(CONFIG_8xx) += test_burst timer
extra-$(CONFIG_MPC8260) += mem_to_mem_idma2intr
extra-$(CONFIG_PPC) += sched
@@ -29,7 +28,6 @@ COBJS := $(ELF:=.o)
LIB = $(obj)/libstubs.o
LIBOBJS-$(CONFIG_PPC) += ppc_longjmp.o ppc_setjmp.o
-LIBOBJS-$(CONFIG_8xx) += test_burst_lib.o
LIBOBJS-y += stubs.o
.SECONDARY: $(call objectify,$(COBJS))
diff --git a/examples/standalone/test_burst.c b/examples/standalone/test_burst.c
deleted file mode 100644
index f2fdbf19dcba1ccc35caa463d961a21d8755e07e..0000000000000000000000000000000000000000
--- a/examples/standalone/test_burst.c
+++ /dev/null
@@ -1,284 +0,0 @@
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * The test exercises SDRAM accesses in burst mode
- */
-
-#include <common.h>
-#include <exports.h>
-
-#include <commproc.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-
-#include <serial.h>
-#include <watchdog.h>
-
-#include "test_burst.h"
-
-/* 8 MB test region of physical RAM */
-#define TEST_PADDR 0x00800000
-/* The uncached virtual region */
-#define TEST_VADDR_NC 0x00800000
-/* The cached virtual region */
-#define TEST_VADDR_C 0x01000000
-/* When an error is detected, the address where the error has been found,
- and also the current and the expected data will be written to
- the following flash address
-*/
-#define TEST_FLASH_ADDR 0x40100000
-
-static void test_prepare (void);
-static int test_burst_start (unsigned long size, unsigned long pattern);
-static void test_map_8M (unsigned long paddr, unsigned long vaddr, int cached);
-static int test_mmu_is_on(void);
-static void test_desc(unsigned long size);
-static void test_error(char * step, volatile void * addr, unsigned long val, unsigned long pattern);
-static void signal_init(void);
-static void signal_start(void);
-static void signal_error(void);
-static void test_usage(void);
-
-static unsigned long test_pattern [] = {
- 0x00000000,
- 0xffffffff,
- 0x55555555,
- 0xaaaaaaaa,
-};
-
-
-int test_burst (int argc, char * const argv[])
-{
- unsigned long size = CACHE_LINE_SIZE;
- unsigned int pass = 0;
- int res = 0;
- int i, j;
-
- if (argc == 3) {
- char * d;
- for (size = 0, d = argv[1]; *d >= '0' && *d <= '9'; d++) {
- size *= 10;
- size += *d - '0';
- }
- if (size == 0 || *d) {
- test_usage();
- return 1;
- }
- for (d = argv[2]; *d >= '0' && *d <= '9'; d++) {
- pass *= 10;
- pass += *d - '0';
- }
- if (*d) {
- test_usage();
- return 1;
- }
- } else if (argc > 3) {
- test_usage();
- return 1;
- }
-
- size += (CACHE_LINE_SIZE - 1);
- size &= ~(CACHE_LINE_SIZE - 1);
-
- if (!test_mmu_is_on()) {
- test_prepare();
- }
-
- test_desc(size);
-
- for (j = 0; !pass || j < pass; j++) {
- for (i = 0; i < sizeof(test_pattern) / sizeof(test_pattern[0]);
- i++) {
- res = test_burst_start(size, test_pattern[i]);
- if (res != 0) {
- goto Done;
- }
- }
-
- printf ("Iteration #%d passed\n", j + 1);
-
- if (tstc() && 0x03 == getc())
- break;
- }
-Done:
- return res;
-}
-
-static void test_prepare (void)
-{
- printf ("\n");
-
- caches_init();
- disable_interrupts();
- mmu_init();
-
- printf ("Interrupts are disabled\n");
- printf ("I-Cache is ON\n");
- printf ("D-Cache is ON\n");
- printf ("MMU is ON\n");
-
- printf ("\n");
-
- test_map_8M (TEST_PADDR, TEST_VADDR_NC, 0);
- test_map_8M (TEST_PADDR, TEST_VADDR_C, 1);
-
- test_map_8M (TEST_FLASH_ADDR & 0xFF800000, TEST_FLASH_ADDR & 0xFF800000, 0);
-
- /* Configure GPIO ports */
- signal_init();
-}
-
-static int test_burst_start (unsigned long size, unsigned long pattern)
-{
- volatile unsigned long * vaddr_c = (unsigned long *)TEST_VADDR_C;
- volatile unsigned long * vaddr_nc = (unsigned long *)TEST_VADDR_NC;
- int i, n;
- int res = 1;
-
- printf ("Test pattern %08lx ...", pattern);
-
- n = size / 4;
-
- for (i = 0; i < n; i ++) {
- vaddr_c [i] = pattern;
- }
- signal_start();
- flush_dcache_range((unsigned long)vaddr_c, (unsigned long)(vaddr_c + n) - 1);
-
- for (i = 0; i < n; i ++) {
- register unsigned long tmp = vaddr_nc [i];
- if (tmp != pattern) {
- test_error("2a", vaddr_nc + i, tmp, pattern);
- goto Done;
- }
- }
-
- for (i = 0; i < n; i ++) {
- register unsigned long tmp = vaddr_c [i];
- if (tmp != pattern) {
- test_error("2b", vaddr_c + i, tmp, pattern);
- goto Done;
- }
- }
-
- for (i = 0; i < n; i ++) {
- vaddr_nc [i] = pattern;
- }
-
- for (i = 0; i < n; i ++) {
- register unsigned long tmp = vaddr_nc [i];
- if (tmp != pattern) {
- test_error("3a", vaddr_nc + i, tmp, pattern);
- goto Done;
- }
- }
-
- signal_start();
- for (i = 0; i < n; i ++) {
- register unsigned long tmp = vaddr_c [i];
- if (tmp != pattern) {
- test_error("3b", vaddr_c + i, tmp, pattern);
- goto Done;
- }
- }
-
- res = 0;
-Done:
- printf(" %s\n", res == 0 ? "OK" : "");
-
- return res;
-}
-
-static void test_map_8M (unsigned long paddr, unsigned long vaddr, int cached)
-{
- mtspr (MD_EPN, (vaddr & 0xFFFFFC00) | MI_EVALID);
- mtspr (MD_TWC, MI_PS8MEG | MI_SVALID);
- mtspr (MD_RPN, (paddr & 0xFFFFF000) | MI_BOOTINIT | (cached ? 0 : 2));
- mtspr (MD_AP, MI_Kp);
-}
-
-static int test_mmu_is_on(void)
-{
- unsigned long msr;
-
- asm volatile("mfmsr %0" : "=r" (msr) :);
-
- return msr & MSR_DR;
-}
-
-static void test_desc(unsigned long size)
-{
- printf(
- "The following tests will be conducted:\n"
- "1) Map %ld-byte region of physical RAM at 0x%08x\n"
- " into two virtual regions:\n"
- " one cached at 0x%08x and\n"
- " the the other uncached at 0x%08x.\n",
- size, TEST_PADDR, TEST_VADDR_NC, TEST_VADDR_C);
-
- puts(
- "2) Fill the cached region with a pattern, and flush the cache\n"
- "2a) Check the uncached region to match the pattern\n"
- "2b) Check the cached region to match the pattern\n"
- "3) Fill the uncached region with a pattern\n"
- "3a) Check the cached region to match the pattern\n"
- "3b) Check the uncached region to match the pattern\n"
- "2b) Change the patterns and go to step 2\n"
- "\n"
- );
-}
-
-static void test_error(
- char * step, volatile void * addr, unsigned long val, unsigned long pattern)
-{
- volatile unsigned long * p = (void *)TEST_FLASH_ADDR;
-
- signal_error();
-
- p[0] = (unsigned long)addr;
- p[1] = val;
- p[2] = pattern;
-
- printf ("\nError at step %s, addr %08lx: read %08lx, pattern %08lx",
- step, (unsigned long)addr, val, pattern);
-}
-
-static void signal_init(void)
-{
-#if defined(GPIO1_INIT)
- GPIO1_INIT;
-#endif
-#if defined(GPIO2_INIT)
- GPIO2_INIT;
-#endif
-}
-
-static void signal_start(void)
-{
-#if defined(GPIO1_INIT)
- if (GPIO1_DAT & GPIO1_BIT) {
- GPIO1_DAT &= ~GPIO1_BIT;
- } else {
- GPIO1_DAT |= GPIO1_BIT;
- }
-#endif
-}
-
-static void signal_error(void)
-{
-#if defined(GPIO2_INIT)
- if (GPIO2_DAT & GPIO2_BIT) {
- GPIO2_DAT &= ~GPIO2_BIT;
- } else {
- GPIO2_DAT |= GPIO2_BIT;
- }
-#endif
-}
-
-static void test_usage(void)
-{
- printf("Usage: go 0x40004 [size] [count]\n");
-}
diff --git a/examples/standalone/test_burst.h b/examples/standalone/test_burst.h
deleted file mode 100644
index 87f5927a8e9125fa8aba385b4b3ab5a35b136679..0000000000000000000000000000000000000000
--- a/examples/standalone/test_burst.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _TEST_BURST_H
-#define _TEST_BURST_H
-
-/* Cache line size */
-#define CACHE_LINE_SIZE 16
-/* Binary logarithm of the cache line size */
-#define LG_CACHE_LINE_SIZE 4
-
-#ifndef __ASSEMBLY__
-extern void mmu_init(void);
-extern void caches_init(void);
-extern void flush_dcache_range(unsigned long start, unsigned long stop);
-#endif
-
-#endif /* _TEST_BURST_H */
diff --git a/examples/standalone/test_burst_lib.S b/examples/standalone/test_burst_lib.S
deleted file mode 100644
index fd3256e88b9901c91b69472c10401801ad448143..0000000000000000000000000000000000000000
--- a/examples/standalone/test_burst_lib.S
+++ /dev/null
@@ -1,154 +0,0 @@
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-#include <asm/cache.h>
-#include <asm/mmu.h>
-#include "test_burst.h"
-
- .text
-/*
- * void mmu_init(void);
- *
- * This function turns the MMU on
- *
- * Three 8 MByte regions are mapped 1:1, uncached
- * - SDRAM lower 8 MByte
- * - SDRAM higher 8 MByte
- * - IMMR
- */
- .global mmu_init
-mmu_init:
- tlbia /* Invalidate all TLB entries */
- li r8, 0
- mtspr MI_CTR, r8 /* Set instruction control to zero */
- lis r8, MD_RESETVAL@h
- mtspr MD_CTR, r8 /* Set data TLB control */
-
- /* Now map the lower 8 Meg into the TLBs. For this quick hack,
- * we can load the instruction and data TLB registers with the
- * same values.
- */
- li r8, MI_EVALID /* Create EPN for address 0 */
- mtspr MI_EPN, r8
- mtspr MD_EPN, r8
- li r8, MI_PS8MEG /* Set 8M byte page */
- ori r8, r8, MI_SVALID /* Make it valid */
- mtspr MI_TWC, r8
- mtspr MD_TWC, r8
- li r8, MI_BOOTINIT|0x2 /* Create RPN for address 0 */
- mtspr MI_RPN, r8 /* Store TLB entry */
- mtspr MD_RPN, r8
- lis r8, MI_Kp@h /* Set the protection mode */
- mtspr MI_AP, r8
- mtspr MD_AP, r8
-
- /* Now map the higher 8 Meg into the TLBs. For this quick hack,
- * we can load the instruction and data TLB registers with the
- * same values.
- */
- lwz r9,20(r2) /* gd->ram_size */
- addis r9,r9,-0x80
-
- mr r8, r9 /* Higher 8 Meg in SDRAM */
- ori r8, r8, MI_EVALID /* Mark page valid */
- mtspr MI_EPN, r8
- mtspr MD_EPN, r8
- li r8, MI_PS8MEG /* Set 8M byte page */
- ori r8, r8, MI_SVALID /* Make it valid */
- mtspr MI_TWC, r8
- mtspr MD_TWC, r8
- mr r8, r9
- ori r8, r8, MI_BOOTINIT|0x2
- mtspr MI_RPN, r8 /* Store TLB entry */
- mtspr MD_RPN, r8
- lis r8, MI_Kp@h /* Set the protection mode */
- mtspr MI_AP, r8
- mtspr MD_AP, r8
-
- /* Map another 8 MByte at the IMMR to get the processor
- * internal registers (among other things).
- */
- mfspr r9, 638 /* Get current IMMR */
- andis. r9, r9, 0xff80 /* Get 8Mbyte boundary */
-
- mr r8, r9 /* Create vaddr for TLB */
- ori r8, r8, MD_EVALID /* Mark it valid */
- mtspr MD_EPN, r8
- li r8, MD_PS8MEG /* Set 8M byte page */
- ori r8, r8, MD_SVALID /* Make it valid */
- mtspr MD_TWC, r8
- mr r8, r9 /* Create paddr for TLB */
- ori r8, r8, MI_BOOTINIT|0x2 /* Inhibit cache -- Cort */
- mtspr MD_RPN, r8
-
- /* We now have the lower and higher 8 Meg mapped into TLB entries,
- * and the caches ready to work.
- */
- mfmsr r0
- ori r0,r0,MSR_DR|MSR_IR
- mtspr SRR1,r0
- mflr r0
- mtspr SRR0,r0
- SYNC
- rfi /* enables MMU */
-
-/*
- * void caches_init(void);
- */
- .globl caches_init
-caches_init:
- sync
-
- mfspr r3, IC_CST /* Clear error bits */
- mfspr r3, DC_CST
-
- lis r3, IDC_UNALL@h /* Unlock all */
- mtspr IC_CST, r3
- mtspr DC_CST, r3
-
- lis r3, IDC_INVALL@h /* Invalidate all */
- mtspr IC_CST, r3
- mtspr DC_CST, r3
-
- lis r3, IDC_ENABLE@h /* Enable all */
- mtspr IC_CST, r3
- mtspr DC_CST, r3
-
- blr
-
-/*
- * void flush_dcache_range(unsigned long start, unsigned long stop);
- */
- .global flush_dcache_range
-flush_dcache_range:
- li r5,CACHE_LINE_SIZE-1
- andc r3,r3,r5
- subf r4,r3,r4
- add r4,r4,r5
- srwi. r4,r4,LG_CACHE_LINE_SIZE
- beqlr
- mtctr r4
-
-1: dcbf 0,r3
- addi r3,r3,CACHE_LINE_SIZE
- bdnz 1b
- sync /* wait for dcbf's to get to ram */
- blr
-
-/*
- * void disable_interrupts(void);
- */
- .global disable_interrupts
-disable_interrupts:
- mfmsr r0
- rlwinm r0,r0,0,17,15
- mtmsr r0
- blr
diff --git a/examples/standalone/timer.c b/examples/standalone/timer.c
deleted file mode 100644
index dbd5c16f97f8a16402bdfe050eebc331e5a326ca..0000000000000000000000000000000000000000
--- a/examples/standalone/timer.c
+++ /dev/null
@@ -1,333 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <commproc.h>
-#include <mpc8xx_irq.h>
-#include <exports.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#undef DEBUG
-
-#define TIMER_PERIOD 1000000 /* 1 second clock */
-
-static void timer_handler (void *arg);
-
-
-/* Access functions for the Machine State Register */
-static __inline__ unsigned long get_msr(void)
-{
- unsigned long msr;
-
- asm volatile("mfmsr %0" : "=r" (msr) :);
- return msr;
-}
-
-static __inline__ void set_msr(unsigned long msr)
-{
- asm volatile("mtmsr %0" : : "r" (msr));
-}
-
-/*
- * Definitions to access the CPM Timer registers
- * See 8xx_immap.h for Internal Memory Map layout,
- * and commproc.h for CPM Interrupt vectors (aka "IRQ"s)
- */
-
-typedef struct tid_8xx_cpmtimer_s {
- int cpm_vec; /* CPM Interrupt Vector for this timer */
- ushort *tgcrp; /* Pointer to Timer Global Config Reg. */
- ushort *tmrp; /* Pointer to Timer Mode Register */
- ushort *trrp; /* Pointer to Timer Reference Register */
- ushort *tcrp; /* Pointer to Timer Capture Register */
- ushort *tcnp; /* Pointer to Timer Counter Register */
- ushort *terp; /* Pointer to Timer Event Register */
-} tid_8xx_cpmtimer_t;
-
-#ifndef CLOCKRATE
-# define CLOCKRATE 64
-#endif
-
-#define CPMT_CLOCK_DIV 16
-#define CPMT_MAX_PRESCALER 256
-#define CPMT_MAX_REFERENCE 65535 /* max. unsigned short */
-
-#define CPMT_MAX_TICKS (CPMT_MAX_REFERENCE * CPMT_MAX_PRESCALER)
-#define CPMT_MAX_TICKS_WITH_DIV (CPMT_MAX_REFERENCE * CPMT_MAX_PRESCALER * CPMT_CLOCK_DIV)
-#define CPMT_MAX_INTERVAL (CPMT_MAX_TICKS_WITH_DIV / CLOCKRATE)
-
-/* For now: always use max. prescaler value */
-#define CPMT_PRESCALER (CPMT_MAX_PRESCALER)
-
-/* CPM Timer Event Register Bits */
-#define CPMT_EVENT_CAP 0x0001 /* Capture Event */
-#define CPMT_EVENT_REF 0x0002 /* Reference Counter Event */
-
-/* CPM Timer Global Config Register */
-#define CPMT_GCR_RST 0x0001 /* Reset Timer */
-#define CPMT_GCR_STP 0x0002 /* Stop Timer */
-#define CPMT_GCR_FRZ 0x0004 /* Freeze Timer */
-#define CPMT_GCR_GM_CAS 0x0008 /* Gate Mode / Cascade Timers */
-#define CPMT_GCR_MASK (CPMT_GCR_RST|CPMT_GCR_STP|CPMT_GCR_FRZ|CPMT_GCR_GM_CAS)
-
-/* CPM Timer Mode register */
-#define CPMT_MR_GE 0x0001 /* Gate Enable */
-#define CPMT_MR_ICLK_CASC 0x0000 /* Clock internally cascaded */
-#define CPMT_MR_ICLK_CLK 0x0002 /* Clock = system clock */
-#define CPMT_MR_ICLK_CLKDIV 0x0004 /* Clock = system clock / 16 */
-#define CPMT_MR_ICLK_TIN 0x0006 /* Clock = TINx signal */
-#define CPMT_MR_FRR 0x0008 /* Free Run / Restart */
-#define CPMT_MR_ORI 0x0010 /* Out. Reference Interrupt En. */
-#define CPMT_MR_OM 0x0020 /* Output Mode */
-#define CPMT_MR_CE_DIS 0x0000 /* Capture/Interrupt disabled */
-#define CPMT_MR_CE_RISE 0x0040 /* Capt./Interr. on rising TIN */
-#define CPMT_MR_CE_FALL 0x0080 /* Capt./Interr. on falling TIN */
-#define CPMT_MR_CE_ANY 0x00C0 /* Capt./Interr. on any TIN edge*/
-
-
-/*
- * which CPM timer to use - index starts at 0 (= timer 1)
- */
-#define TID_TIMER_ID 0 /* use CPM timer 1 */
-
-void setPeriod (tid_8xx_cpmtimer_t *hwp, ulong interval);
-
-static const char usage[] = "\n[q, b, e, ?] ";
-
-int timer (int argc, char * const argv[])
-{
- cpmtimer8xx_t *cpmtimerp; /* Pointer to the CPM Timer structure */
- tid_8xx_cpmtimer_t hw;
- tid_8xx_cpmtimer_t *hwp = &hw;
- int c;
- int running;
-
- app_startup(argv);
-
- /* Pointer to CPM Timer structure */
- cpmtimerp = &((immap_t *) gd->bd->bi_immr_base)->im_cpmtimer;
-
- printf ("TIMERS=0x%x\n", (unsigned) cpmtimerp);
-
- /* Initialize pointers depending on which timer we use */
- switch (TID_TIMER_ID) {
- case 0:
- hwp->tmrp = &(cpmtimerp->cpmt_tmr1);
- hwp->trrp = &(cpmtimerp->cpmt_trr1);
- hwp->tcrp = &(cpmtimerp->cpmt_tcr1);
- hwp->tcnp = &(cpmtimerp->cpmt_tcn1);
- hwp->terp = &(cpmtimerp->cpmt_ter1);
- hwp->cpm_vec = CPMVEC_TIMER1;
- break;
- case 1:
- hwp->tmrp = &(cpmtimerp->cpmt_tmr2);
- hwp->trrp = &(cpmtimerp->cpmt_trr2);
- hwp->tcrp = &(cpmtimerp->cpmt_tcr2);
- hwp->tcnp = &(cpmtimerp->cpmt_tcn2);
- hwp->terp = &(cpmtimerp->cpmt_ter2);
- hwp->cpm_vec = CPMVEC_TIMER2;
- break;
- case 2:
- hwp->tmrp = &(cpmtimerp->cpmt_tmr3);
- hwp->trrp = &(cpmtimerp->cpmt_trr3);
- hwp->tcrp = &(cpmtimerp->cpmt_tcr3);
- hwp->tcnp = &(cpmtimerp->cpmt_tcn3);
- hwp->terp = &(cpmtimerp->cpmt_ter3);
- hwp->cpm_vec = CPMVEC_TIMER3;
- break;
- case 3:
- hwp->tmrp = &(cpmtimerp->cpmt_tmr4);
- hwp->trrp = &(cpmtimerp->cpmt_trr4);
- hwp->tcrp = &(cpmtimerp->cpmt_tcr4);
- hwp->tcnp = &(cpmtimerp->cpmt_tcn4);
- hwp->terp = &(cpmtimerp->cpmt_ter4);
- hwp->cpm_vec = CPMVEC_TIMER4;
- break;
- }
-
- hwp->tgcrp = &cpmtimerp->cpmt_tgcr;
-
- printf ("Using timer %d\n"
- "tgcr @ 0x%x, tmr @ 0x%x, trr @ 0x%x,"
- " tcr @ 0x%x, tcn @ 0x%x, ter @ 0x%x\n",
- TID_TIMER_ID + 1,
- (unsigned) hwp->tgcrp,
- (unsigned) hwp->tmrp,
- (unsigned) hwp->trrp,
- (unsigned) hwp->tcrp,
- (unsigned) hwp->tcnp,
- (unsigned) hwp->terp
- );
-
- /* reset timer */
- *hwp->tgcrp &= ~(CPMT_GCR_MASK << TID_TIMER_ID);
-
- /* clear all events */
- *hwp->terp = (CPMT_EVENT_CAP | CPMT_EVENT_REF);
-
- puts(usage);
- running = 0;
- while ((c = getc()) != 'q') {
- if (c == 'b') {
-
- setPeriod (hwp, TIMER_PERIOD); /* Set period and start ticking */
-
- /* Install interrupt handler (enable timer in CIMR) */
- install_hdlr (hwp->cpm_vec, timer_handler, hwp);
-
- printf ("Enabling timer\n");
-
- /* enable timer */
- *hwp->tgcrp |= (CPMT_GCR_RST << TID_TIMER_ID);
- running = 1;
-
-#ifdef DEBUG
- printf ("tgcr=0x%x, tmr=0x%x, trr=0x%x,"
- " tcr=0x%x, tcn=0x%x, ter=0x%x\n",
- *hwp->tgcrp, *hwp->tmrp, *hwp->trrp,
- *hwp->tcrp, *hwp->tcnp, *hwp->terp
- );
-#endif
- } else if (c == 'e') {
-
- printf ("Stopping timer\n");
-
- *hwp->tgcrp &= ~(CPMT_GCR_MASK << TID_TIMER_ID);
- running = 0;
-
-#ifdef DEBUG
- printf ("tgcr=0x%x, tmr=0x%x, trr=0x%x,"
- " tcr=0x%x, tcn=0x%x, ter=0x%x\n",
- *hwp->tgcrp, *hwp->tmrp, *hwp->trrp,
- *hwp->tcrp, *hwp->tcnp, *hwp->terp
- );
-#endif
- /* Uninstall interrupt handler */
- free_hdlr (hwp->cpm_vec);
-
- } else if (c == '?') {
-#ifdef DEBUG
- cpic8xx_t *cpm_icp = &((immap_t *) gd->bd->bi_immr_base)->im_cpic;
- sysconf8xx_t *siup = &((immap_t *) gd->bd->bi_immr_base)->im_siu_conf;
-#endif
-
- printf ("\ntgcr=0x%x, tmr=0x%x, trr=0x%x,"
- " tcr=0x%x, tcn=0x%x, ter=0x%x\n",
- *hwp->tgcrp, *hwp->tmrp, *hwp->trrp,
- *hwp->tcrp, *hwp->tcnp, *hwp->terp
- );
-#ifdef DEBUG
- printf ("SIUMCR=0x%08lx, SYPCR=0x%08lx,"
- " SIMASK=0x%08lx, SIPEND=0x%08lx\n",
- siup->sc_siumcr,
- siup->sc_sypcr,
- siup->sc_simask,
- siup->sc_sipend
- );
-
- printf ("CIMR=0x%08lx, CICR=0x%08lx, CIPR=0x%08lx\n",
- cpm_icp->cpic_cimr,
- cpm_icp->cpic_cicr,
- cpm_icp->cpic_cipr
- );
-#endif
- } else {
- printf ("\nEnter: q - quit, b - start timer, e - stop timer, ? - get status\n");
- }
- puts(usage);
- }
- if (running) {
- printf ("Stopping timer\n");
- *hwp->tgcrp &= ~(CPMT_GCR_MASK << TID_TIMER_ID);
- free_hdlr (hwp->cpm_vec);
- }
-
- return (0);
-}
-
-
-/* Set period in microseconds and start.
- * Truncate to maximum period if more than this is requested - but warn about it.
- */
-
-void setPeriod (tid_8xx_cpmtimer_t *hwp, ulong interval)
-{
- unsigned short prescaler;
- unsigned long ticks;
-
- printf ("Set interval %ld us\n", interval);
-
- /* Warn if requesting longer period than possible */
- if (interval > CPMT_MAX_INTERVAL) {
- printf ("Truncate interval %ld to maximum (%d)\n",
- interval, CPMT_MAX_INTERVAL);
- interval = CPMT_MAX_INTERVAL;
- }
- /*
- * Check if we want to use clock divider:
- * Since the reference counter can be incremented only in integer steps,
- * we try to keep it as big as possible to allow the resulting period to be
- * as precise as possible.
- */
- /* prescaler, enable interrupt, restart after ref count is reached */
- prescaler = (ushort) ((CPMT_PRESCALER - 1) << 8) |
- CPMT_MR_ORI |
- CPMT_MR_FRR;
-
- ticks = ((ulong) CLOCKRATE * interval);
-
- if (ticks > CPMT_MAX_TICKS) {
- ticks /= CPMT_CLOCK_DIV;
- prescaler |= CPMT_MR_ICLK_CLKDIV; /* use system clock divided by 16 */
- } else {
- prescaler |= CPMT_MR_ICLK_CLK; /* use system clock without divider */
- }
-
-#ifdef DEBUG
- printf ("clock/%d, prescale factor %d, reference %ld, ticks %ld\n",
- (ticks > CPMT_MAX_TICKS) ? CPMT_CLOCK_DIV : 1,
- CPMT_PRESCALER,
- (ticks / CPMT_PRESCALER),
- ticks
- );
-#endif
-
- /* set prescaler register */
- *hwp->tmrp = prescaler;
-
- /* clear timer counter */
- *hwp->tcnp = 0;
-
- /* set reference register */
- *hwp->trrp = (unsigned short) (ticks / CPMT_PRESCALER);
-
-#ifdef DEBUG
- printf ("tgcr=0x%x, tmr=0x%x, trr=0x%x,"
- " tcr=0x%x, tcn=0x%x, ter=0x%x\n",
- *hwp->tgcrp, *hwp->tmrp, *hwp->trrp,
- *hwp->tcrp, *hwp->tcnp, *hwp->terp
- );
-#endif
-}
-
-/*
- * Handler for CPMVEC_TIMER1 interrupt
- */
-static
-void timer_handler (void *arg)
-{
- tid_8xx_cpmtimer_t *hwp = (tid_8xx_cpmtimer_t *)arg;
-
- /* printf ("** TER1=%04x ** ", *hwp->terp); */
-
- /* just for demonstration */
- printf (".");
-
- /* clear all possible events: Ref. and Cap. */
- *hwp->terp = (CPMT_EVENT_CAP | CPMT_EVENT_REF);
-}
diff --git a/include/asm-generic/u-boot.h b/include/asm-generic/u-boot.h
index 9f3351d602e86442cb1a302e37d275fe0aeec8ed..4374c2ee0836104a021f43b56bfb53e4d572bb5f 100644
--- a/include/asm-generic/u-boot.h
+++ b/include/asm-generic/u-boot.h
@@ -41,7 +41,7 @@ typedef struct bd_info {
unsigned long bi_dsp_freq; /* dsp core frequency */
unsigned long bi_ddr_freq; /* ddr frequency */
#endif
-#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || defined(CONFIG_MPC8260) \
+#if defined(CONFIG_5xx) || defined(CONFIG_MPC8260) \
|| defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
unsigned long bi_immr_base; /* base of IMMR register */
#endif
diff --git a/include/commproc.h b/include/commproc.h
deleted file mode 100644
index 9d4cb109adde161251a9ae18ac6625ae6b5f9f9d..0000000000000000000000000000000000000000
--- a/include/commproc.h
+++ /dev/null
@@ -1,849 +0,0 @@
-/*
- * MPC8xx Communication Processor Module.
- * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
- *
- * (C) Copyright 2000-2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * This file contains structures and information for the communication
- * processor channels. Some CPM control and status is available
- * throught the MPC8xx internal memory map. See immap.h for details.
- * This file only contains what I need for the moment, not the total
- * CPM capabilities. I (or someone else) will add definitions as they
- * are needed. -- Dan
- *
- */
-#ifndef __CPM_8XX__
-#define __CPM_8XX__
-
-#include <asm/8xx_immap.h>
-
-/* CPM Command register.
-*/
-#define CPM_CR_RST ((ushort)0x8000)
-#define CPM_CR_OPCODE ((ushort)0x0f00)
-#define CPM_CR_CHAN ((ushort)0x00f0)
-#define CPM_CR_FLG ((ushort)0x0001)
-
-/* Some commands (there are more...later)
-*/
-#define CPM_CR_INIT_TRX ((ushort)0x0000)
-#define CPM_CR_INIT_RX ((ushort)0x0001)
-#define CPM_CR_INIT_TX ((ushort)0x0002)
-#define CPM_CR_HUNT_MODE ((ushort)0x0003)
-#define CPM_CR_STOP_TX ((ushort)0x0004)
-#define CPM_CR_RESTART_TX ((ushort)0x0006)
-#define CPM_CR_SET_GADDR ((ushort)0x0008)
-
-/* Channel numbers.
-*/
-#define CPM_CR_CH_SCC1 ((ushort)0x0000)
-#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
-#define CPM_CR_CH_SCC2 ((ushort)0x0004)
-#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI/IDMA2/Timers */
-#define CPM_CR_CH_SCC3 ((ushort)0x0008)
-#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
-#define CPM_CR_CH_SCC4 ((ushort)0x000c)
-#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
-
-#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
-
-/*
- * DPRAM defines and allocation functions
- */
-#define CPM_SERIAL_BASE 0x0800
-#define CPM_I2C_BASE 0x0820
-#define CPM_SPI_BASE 0x0840
-#define CPM_FEC_BASE 0x0860
-#define CPM_SERIAL2_BASE 0x08E0
-#define CPM_SCC_BASE 0x0900
-#define CPM_POST_BASE 0x0980
-#define CPM_WLKBD_BASE 0x0a00
-
-#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
-#define CPM_POST_WORD_ADDR 0x07FC
-#else
-#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR
-#endif
-
-#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR
-#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong))
-#else
-#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR
-#endif
-
-#define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */
-
-/* Export the base address of the communication processor registers
- * and dual port ram.
- */
-extern cpm8xx_t *cpmp; /* Pointer to comm processor */
-
-/* Buffer descriptors used by many of the CPM protocols.
-*/
-typedef struct cpm_buf_desc {
- ushort cbd_sc; /* Status and Control */
- ushort cbd_datlen; /* Data length in buffer */
- uint cbd_bufaddr; /* Buffer address in host memory */
-} cbd_t;
-
-#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
-#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
-#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
-#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
-#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
-#define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */
-#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
-#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
-#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
-#define BD_SC_BR ((ushort)0x0020) /* Break received */
-#define BD_SC_FR ((ushort)0x0010) /* Framing error */
-#define BD_SC_PR ((ushort)0x0008) /* Parity error */
-#define BD_SC_OV ((ushort)0x0002) /* Overrun */
-#define BD_SC_CD ((ushort)0x0001) /* Carrier Detect lost */
-
-/* Parameter RAM offsets.
-*/
-#define PROFF_SCC1 ((uint)0x0000)
-#define PROFF_IIC ((uint)0x0080)
-#define PROFF_REVNUM ((uint)0x00b0)
-#define PROFF_SCC2 ((uint)0x0100)
-#define PROFF_SPI ((uint)0x0180)
-#define PROFF_SCC3 ((uint)0x0200)
-#define PROFF_SMC1 ((uint)0x0280)
-#define PROFF_SCC4 ((uint)0x0300)
-#define PROFF_SMC2 ((uint)0x0380)
-
-/* Define enough so I can at least use the serial port as a UART.
- */
-typedef struct smc_uart {
- ushort smc_rbase; /* Rx Buffer descriptor base address */
- ushort smc_tbase; /* Tx Buffer descriptor base address */
- u_char smc_rfcr; /* Rx function code */
- u_char smc_tfcr; /* Tx function code */
- ushort smc_mrblr; /* Max receive buffer length */
- uint smc_rstate; /* Internal */
- uint smc_idp; /* Internal */
- ushort smc_rbptr; /* Internal */
- ushort smc_ibc; /* Internal */
- uint smc_rxtmp; /* Internal */
- uint smc_tstate; /* Internal */
- uint smc_tdp; /* Internal */
- ushort smc_tbptr; /* Internal */
- ushort smc_tbc; /* Internal */
- uint smc_txtmp; /* Internal */
- ushort smc_maxidl; /* Maximum idle characters */
- ushort smc_tmpidl; /* Temporary idle counter */
- ushort smc_brklen; /* Last received break length */
- ushort smc_brkec; /* rcv'd break condition counter */
- ushort smc_brkcr; /* xmt break count register */
- ushort smc_rmask; /* Temporary bit mask */
- u_char res1[8];
- ushort smc_rpbase; /* Relocation pointer */
-} smc_uart_t;
-
-/* Function code bits.
-*/
-#define SMC_EB ((u_char)0x10) /* Set big endian byte order */
-
-/* SMC uart mode register.
-*/
-#define SMCMR_REN ((ushort)0x0001)
-#define SMCMR_TEN ((ushort)0x0002)
-#define SMCMR_DM ((ushort)0x000c)
-#define SMCMR_SM_GCI ((ushort)0x0000)
-#define SMCMR_SM_UART ((ushort)0x0020)
-#define SMCMR_SM_TRANS ((ushort)0x0030)
-#define SMCMR_SM_MASK ((ushort)0x0030)
-#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
-#define SMCMR_REVD SMCMR_PM_EVEN
-#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
-#define SMCMR_BS SMCMR_PEN
-#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
-#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
-#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
-
-/* SMC2 as Centronics parallel printer. It is half duplex, in that
- * it can only receive or transmit. The parameter ram values for
- * each direction are either unique or properly overlap, so we can
- * include them in one structure.
- */
-typedef struct smc_centronics {
- ushort scent_rbase;
- ushort scent_tbase;
- u_char scent_cfcr;
- u_char scent_smask;
- ushort scent_mrblr;
- uint scent_rstate;
- uint scent_r_ptr;
- ushort scent_rbptr;
- ushort scent_r_cnt;
- uint scent_rtemp;
- uint scent_tstate;
- uint scent_t_ptr;
- ushort scent_tbptr;
- ushort scent_t_cnt;
- uint scent_ttemp;
- ushort scent_max_sl;
- ushort scent_sl_cnt;
- ushort scent_character1;
- ushort scent_character2;
- ushort scent_character3;
- ushort scent_character4;
- ushort scent_character5;
- ushort scent_character6;
- ushort scent_character7;
- ushort scent_character8;
- ushort scent_rccm;
- ushort scent_rccr;
-} smc_cent_t;
-
-/* Centronics Status Mask Register.
-*/
-#define SMC_CENT_F ((u_char)0x08)
-#define SMC_CENT_PE ((u_char)0x04)
-#define SMC_CENT_S ((u_char)0x02)
-
-/* SMC Event and Mask register.
-*/
-#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
-#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
-#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */
-#define SMCM_BSY ((unsigned char)0x04)
-#define SMCM_TX ((unsigned char)0x02)
-#define SMCM_RX ((unsigned char)0x01)
-
-/* Baud rate generators.
-*/
-#define CPM_BRG_RST ((uint)0x00020000)
-#define CPM_BRG_EN ((uint)0x00010000)
-#define CPM_BRG_EXTC_INT ((uint)0x00000000)
-#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000)
-#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000)
-#define CPM_BRG_ATB ((uint)0x00002000)
-#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
-#define CPM_BRG_DIV16 ((uint)0x00000001)
-
-/* SI Clock Route Register
-*/
-#define SICR_RCLK_SCC1_BRG1 ((uint)0x00000000)
-#define SICR_TCLK_SCC1_BRG1 ((uint)0x00000000)
-#define SICR_RCLK_SCC2_BRG2 ((uint)0x00000800)
-#define SICR_TCLK_SCC2_BRG2 ((uint)0x00000100)
-#define SICR_RCLK_SCC3_BRG3 ((uint)0x00100000)
-#define SICR_TCLK_SCC3_BRG3 ((uint)0x00020000)
-#define SICR_RCLK_SCC4_BRG4 ((uint)0x18000000)
-#define SICR_TCLK_SCC4_BRG4 ((uint)0x03000000)
-
-/* SCCs.
-*/
-#define SCC_GSMRH_IRP ((uint)0x00040000)
-#define SCC_GSMRH_GDE ((uint)0x00010000)
-#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
-#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
-#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
-#define SCC_GSMRH_REVD ((uint)0x00002000)
-#define SCC_GSMRH_TRX ((uint)0x00001000)
-#define SCC_GSMRH_TTX ((uint)0x00000800)
-#define SCC_GSMRH_CDP ((uint)0x00000400)
-#define SCC_GSMRH_CTSP ((uint)0x00000200)
-#define SCC_GSMRH_CDS ((uint)0x00000100)
-#define SCC_GSMRH_CTSS ((uint)0x00000080)
-#define SCC_GSMRH_TFL ((uint)0x00000040)
-#define SCC_GSMRH_RFW ((uint)0x00000020)
-#define SCC_GSMRH_TXSY ((uint)0x00000010)
-#define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
-#define SCC_GSMRH_SYNL8 ((uint)0x00000008)
-#define SCC_GSMRH_SYNL4 ((uint)0x00000004)
-#define SCC_GSMRH_RTSM ((uint)0x00000002)
-#define SCC_GSMRH_RSYN ((uint)0x00000001)
-
-#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
-#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
-#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
-#define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
-#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
-#define SCC_GSMRL_TCI ((uint)0x10000000)
-#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
-#define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
-#define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
-#define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
-#define SCC_GSMRL_RINV ((uint)0x02000000)
-#define SCC_GSMRL_TINV ((uint)0x01000000)
-#define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
-#define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
-#define SCC_GSMRL_TPL_48 ((uint)0x00800000)
-#define SCC_GSMRL_TPL_32 ((uint)0x00600000)
-#define SCC_GSMRL_TPL_16 ((uint)0x00400000)
-#define SCC_GSMRL_TPL_8 ((uint)0x00200000)
-#define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
-#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
-#define SCC_GSMRL_TPP_01 ((uint)0x00100000)
-#define SCC_GSMRL_TPP_10 ((uint)0x00080000)
-#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
-#define SCC_GSMRL_TEND ((uint)0x00040000)
-#define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
-#define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
-#define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
-#define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
-#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
-#define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
-#define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
-#define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
-#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
-#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
-#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
-#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
-#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
-#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
-#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
-#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
-#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
-#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
-#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
-#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
-#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
-#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
-#define SCC_GSMRL_ENR ((uint)0x00000020)
-#define SCC_GSMRL_ENT ((uint)0x00000010)
-#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
-#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
-#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
-#define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
-#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
-#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
-#define SCC_GSMRL_MODE_UART ((uint)0x00000004)
-#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
-#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
-#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
-
-#define SCC_TODR_TOD ((ushort)0x8000)
-
-/* SCC Event and Mask register.
-*/
-#define SCCM_TXE ((unsigned char)0x10)
-#define SCCM_BSY ((unsigned char)0x04)
-#define SCCM_TX ((unsigned char)0x02)
-#define SCCM_RX ((unsigned char)0x01)
-
-typedef struct scc_param {
- ushort scc_rbase; /* Rx Buffer descriptor base address */
- ushort scc_tbase; /* Tx Buffer descriptor base address */
- u_char scc_rfcr; /* Rx function code */
- u_char scc_tfcr; /* Tx function code */
- ushort scc_mrblr; /* Max receive buffer length */
- uint scc_rstate; /* Internal */
- uint scc_idp; /* Internal */
- ushort scc_rbptr; /* Internal */
- ushort scc_ibc; /* Internal */
- uint scc_rxtmp; /* Internal */
- uint scc_tstate; /* Internal */
- uint scc_tdp; /* Internal */
- ushort scc_tbptr; /* Internal */
- ushort scc_tbc; /* Internal */
- uint scc_txtmp; /* Internal */
- uint scc_rcrc; /* Internal */
- uint scc_tcrc; /* Internal */
-} sccp_t;
-
-/* Function code bits.
-*/
-#define SCC_EB ((u_char)0x10) /* Set big endian byte order */
-
-/* CPM Ethernet through SCCx.
- */
-typedef struct scc_enet {
- sccp_t sen_genscc;
- uint sen_cpres; /* Preset CRC */
- uint sen_cmask; /* Constant mask for CRC */
- uint sen_crcec; /* CRC Error counter */
- uint sen_alec; /* alignment error counter */
- uint sen_disfc; /* discard frame counter */
- ushort sen_pads; /* Tx short frame pad character */
- ushort sen_retlim; /* Retry limit threshold */
- ushort sen_retcnt; /* Retry limit counter */
- ushort sen_maxflr; /* maximum frame length register */
- ushort sen_minflr; /* minimum frame length register */
- ushort sen_maxd1; /* maximum DMA1 length */
- ushort sen_maxd2; /* maximum DMA2 length */
- ushort sen_maxd; /* Rx max DMA */
- ushort sen_dmacnt; /* Rx DMA counter */
- ushort sen_maxb; /* Max BD byte count */
- ushort sen_gaddr1; /* Group address filter */
- ushort sen_gaddr2;
- ushort sen_gaddr3;
- ushort sen_gaddr4;
- uint sen_tbuf0data0; /* Save area 0 - current frame */
- uint sen_tbuf0data1; /* Save area 1 - current frame */
- uint sen_tbuf0rba; /* Internal */
- uint sen_tbuf0crc; /* Internal */
- ushort sen_tbuf0bcnt; /* Internal */
- ushort sen_paddrh; /* physical address (MSB) */
- ushort sen_paddrm;
- ushort sen_paddrl; /* physical address (LSB) */
- ushort sen_pper; /* persistence */
- ushort sen_rfbdptr; /* Rx first BD pointer */
- ushort sen_tfbdptr; /* Tx first BD pointer */
- ushort sen_tlbdptr; /* Tx last BD pointer */
- uint sen_tbuf1data0; /* Save area 0 - current frame */
- uint sen_tbuf1data1; /* Save area 1 - current frame */
- uint sen_tbuf1rba; /* Internal */
- uint sen_tbuf1crc; /* Internal */
- ushort sen_tbuf1bcnt; /* Internal */
- ushort sen_txlen; /* Tx Frame length counter */
- ushort sen_iaddr1; /* Individual address filter */
- ushort sen_iaddr2;
- ushort sen_iaddr3;
- ushort sen_iaddr4;
- ushort sen_boffcnt; /* Backoff counter */
-
- /* NOTE: Some versions of the manual have the following items
- * incorrectly documented. Below is the proper order.
- */
- ushort sen_taddrh; /* temp address (MSB) */
- ushort sen_taddrm;
- ushort sen_taddrl; /* temp address (LSB) */
-} scc_enet_t;
-
-/**********************************************************************
- *
- * Board specific configuration settings.
- *
- * Please note that we use the presence of a #define SCC_ENET and/or
- * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
- **********************************************************************/
-
-/*** BSEIP **********************************************************/
-
-#ifdef CONFIG_BSEIP
-/* This ENET stuff is for the MPC823 with ethernet on SCC2.
- * This is unique to the BSE ip-Engine board.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0200)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-/* BSE uses port B and C bits for PHY control also.
-*/
-#define PB_BSE_POWERUP ((uint)0x00000004)
-#define PB_BSE_FDXDIS ((uint)0x00008000)
-#define PC_BSE_LOOPBACK ((ushort)0x0800)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002c00)
-#endif /* CONFIG_BSEIP */
-
-/*** KM8XX *********************************************************/
-
-/* The KM8XX Service Module uses SCC3 for Ethernet */
-
-#ifdef CONFIG_KM8XX
-#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
-#define CPM_CR_ENET CPM_CR_CH_SCC3
-#define SCC_ENET 2
-#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */
-#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */
-#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */
-#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */
-
-#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
-
-#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */
-#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */
-
-/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to
- * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x00FF0000)
-#define SICR_ENET_CLKRT ((uint)0x00250000)
-#endif /* CONFIG_KM8XX */
-
-/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
-
-#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
- defined(CONFIG_TQM823L) || \
- defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
- defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D)
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002600)
-
-# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
-#define FEC_ENET
-# endif /* CONFIG_FEC_ENET */
-
-#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
-
-/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
-
-#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
- defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
- defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
- defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
-
-# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x00000026)
-
-# endif /* CONFIG_SCC1_ENET */
-
-# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
-
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-# endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */
-
-/*********************************************************************/
-
-/* SCC Event register as used by Ethernet.
-*/
-#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
-#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
-#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
-#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
-#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
-#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
-
-/* SCC Mode Register (PSMR) as used by Ethernet.
-*/
-#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */
-#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */
-#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */
-#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */
-#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
-#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */
-#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
-#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */
-#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */
-#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */
-#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */
-#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
-#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
-
-/* Buffer descriptor control/status used by Ethernet receive.
-*/
-#define BD_ENET_RX_EMPTY ((ushort)0x8000)
-#define BD_ENET_RX_WRAP ((ushort)0x2000)
-#define BD_ENET_RX_INTR ((ushort)0x1000)
-#define BD_ENET_RX_LAST ((ushort)0x0800)
-#define BD_ENET_RX_FIRST ((ushort)0x0400)
-#define BD_ENET_RX_MISS ((ushort)0x0100)
-#define BD_ENET_RX_LG ((ushort)0x0020)
-#define BD_ENET_RX_NO ((ushort)0x0010)
-#define BD_ENET_RX_SH ((ushort)0x0008)
-#define BD_ENET_RX_CR ((ushort)0x0004)
-#define BD_ENET_RX_OV ((ushort)0x0002)
-#define BD_ENET_RX_CL ((ushort)0x0001)
-#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */
-
-/* Buffer descriptor control/status used by Ethernet transmit.
-*/
-#define BD_ENET_TX_READY ((ushort)0x8000)
-#define BD_ENET_TX_PAD ((ushort)0x4000)
-#define BD_ENET_TX_WRAP ((ushort)0x2000)
-#define BD_ENET_TX_INTR ((ushort)0x1000)
-#define BD_ENET_TX_LAST ((ushort)0x0800)
-#define BD_ENET_TX_TC ((ushort)0x0400)
-#define BD_ENET_TX_DEF ((ushort)0x0200)
-#define BD_ENET_TX_HB ((ushort)0x0100)
-#define BD_ENET_TX_LC ((ushort)0x0080)
-#define BD_ENET_TX_RL ((ushort)0x0040)
-#define BD_ENET_TX_RCMASK ((ushort)0x003c)
-#define BD_ENET_TX_UN ((ushort)0x0002)
-#define BD_ENET_TX_CSL ((ushort)0x0001)
-#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
-
-/* SCC as UART
-*/
-typedef struct scc_uart {
- sccp_t scc_genscc;
- uint scc_res1; /* Reserved */
- uint scc_res2; /* Reserved */
- ushort scc_maxidl; /* Maximum idle chars */
- ushort scc_idlc; /* temp idle counter */
- ushort scc_brkcr; /* Break count register */
- ushort scc_parec; /* receive parity error counter */
- ushort scc_frmec; /* receive framing error counter */
- ushort scc_nosec; /* receive noise counter */
- ushort scc_brkec; /* receive break condition counter */
- ushort scc_brkln; /* last received break length */
- ushort scc_uaddr1; /* UART address character 1 */
- ushort scc_uaddr2; /* UART address character 2 */
- ushort scc_rtemp; /* Temp storage */
- ushort scc_toseq; /* Transmit out of sequence char */
- ushort scc_char1; /* control character 1 */
- ushort scc_char2; /* control character 2 */
- ushort scc_char3; /* control character 3 */
- ushort scc_char4; /* control character 4 */
- ushort scc_char5; /* control character 5 */
- ushort scc_char6; /* control character 6 */
- ushort scc_char7; /* control character 7 */
- ushort scc_char8; /* control character 8 */
- ushort scc_rccm; /* receive control character mask */
- ushort scc_rccr; /* receive control character register */
- ushort scc_rlbc; /* receive last break character */
-} scc_uart_t;
-
-/* SCC Event and Mask registers when it is used as a UART.
-*/
-#define UART_SCCM_GLR ((ushort)0x1000)
-#define UART_SCCM_GLT ((ushort)0x0800)
-#define UART_SCCM_AB ((ushort)0x0200)
-#define UART_SCCM_IDL ((ushort)0x0100)
-#define UART_SCCM_GRA ((ushort)0x0080)
-#define UART_SCCM_BRKE ((ushort)0x0040)
-#define UART_SCCM_BRKS ((ushort)0x0020)
-#define UART_SCCM_CCR ((ushort)0x0008)
-#define UART_SCCM_BSY ((ushort)0x0004)
-#define UART_SCCM_TX ((ushort)0x0002)
-#define UART_SCCM_RX ((ushort)0x0001)
-
-/* The SCC PSMR when used as a UART.
-*/
-#define SCU_PSMR_FLC ((ushort)0x8000)
-#define SCU_PSMR_SL ((ushort)0x4000)
-#define SCU_PSMR_CL ((ushort)0x3000)
-#define SCU_PSMR_UM ((ushort)0x0c00)
-#define SCU_PSMR_FRZ ((ushort)0x0200)
-#define SCU_PSMR_RZS ((ushort)0x0100)
-#define SCU_PSMR_SYN ((ushort)0x0080)
-#define SCU_PSMR_DRT ((ushort)0x0040)
-#define SCU_PSMR_PEN ((ushort)0x0010)
-#define SCU_PSMR_RPM ((ushort)0x000c)
-#define SCU_PSMR_REVP ((ushort)0x0008)
-#define SCU_PSMR_TPM ((ushort)0x0003)
-#define SCU_PSMR_TEVP ((ushort)0x0003)
-
-/* CPM Transparent mode SCC.
- */
-typedef struct scc_trans {
- sccp_t st_genscc;
- uint st_cpres; /* Preset CRC */
- uint st_cmask; /* Constant mask for CRC */
-} scc_trans_t;
-
-#define BD_SCC_TX_LAST ((ushort)0x0800)
-
-/* IIC parameter RAM.
-*/
-typedef struct iic {
- ushort iic_rbase; /* Rx Buffer descriptor base address */
- ushort iic_tbase; /* Tx Buffer descriptor base address */
- u_char iic_rfcr; /* Rx function code */
- u_char iic_tfcr; /* Tx function code */
- ushort iic_mrblr; /* Max receive buffer length */
- uint iic_rstate; /* Internal */
- uint iic_rdp; /* Internal */
- ushort iic_rbptr; /* Internal */
- ushort iic_rbc; /* Internal */
- uint iic_rxtmp; /* Internal */
- uint iic_tstate; /* Internal */
- uint iic_tdp; /* Internal */
- ushort iic_tbptr; /* Internal */
- ushort iic_tbc; /* Internal */
- uint iic_txtmp; /* Internal */
- uint iic_res; /* reserved */
- ushort iic_rpbase; /* Relocation pointer */
- ushort iic_res2; /* reserved */
-} iic_t;
-
-/* SPI parameter RAM.
-*/
-typedef struct spi {
- ushort spi_rbase; /* Rx Buffer descriptor base address */
- ushort spi_tbase; /* Tx Buffer descriptor base address */
- u_char spi_rfcr; /* Rx function code */
- u_char spi_tfcr; /* Tx function code */
- ushort spi_mrblr; /* Max receive buffer length */
- uint spi_rstate; /* Internal */
- uint spi_rdp; /* Internal */
- ushort spi_rbptr; /* Internal */
- ushort spi_rbc; /* Internal */
- uint spi_rxtmp; /* Internal */
- uint spi_tstate; /* Internal */
- uint spi_tdp; /* Internal */
- ushort spi_tbptr; /* Internal */
- ushort spi_tbc; /* Internal */
- uint spi_txtmp; /* Internal */
- uint spi_res;
- ushort spi_rpbase; /* Relocation pointer */
- ushort spi_res2;
-} spi_t;
-
-/* SPI Mode register.
-*/
-#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */
-#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */
-#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */
-#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */
-#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */
-#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */
-#define SPMODE_EN ((ushort)0x0100) /* Enable */
-#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */
-#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */
-
-#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4)
-#define SPMODE_PM(x) ((x) &0xF)
-
-/* HDLC parameter RAM.
-*/
-
-typedef struct hdlc_pram_s {
- /*
- * SCC parameter RAM
- */
- ushort rbase; /* Rx Buffer descriptor base address */
- ushort tbase; /* Tx Buffer descriptor base address */
- uchar rfcr; /* Rx function code */
- uchar tfcr; /* Tx function code */
- ushort mrblr; /* Rx buffer length */
- ulong rstate; /* Rx internal state */
- ulong rptr; /* Rx internal data pointer */
- ushort rbptr; /* rb BD Pointer */
- ushort rcount; /* Rx internal byte count */
- ulong rtemp; /* Rx temp */
- ulong tstate; /* Tx internal state */
- ulong tptr; /* Tx internal data pointer */
- ushort tbptr; /* Tx BD pointer */
- ushort tcount; /* Tx byte count */
- ulong ttemp; /* Tx temp */
- ulong rcrc; /* temp receive CRC */
- ulong tcrc; /* temp transmit CRC */
- /*
- * HDLC specific parameter RAM
- */
- uchar res[4]; /* reserved */
- ulong c_mask; /* CRC constant */
- ulong c_pres; /* CRC preset */
- ushort disfc; /* discarded frame counter */
- ushort crcec; /* CRC error counter */
- ushort abtsc; /* abort sequence counter */
- ushort nmarc; /* nonmatching address rx cnt */
- ushort retrc; /* frame retransmission cnt */
- ushort mflr; /* maximum frame length reg */
- ushort max_cnt; /* maximum length counter */
- ushort rfthr; /* received frames threshold */
- ushort rfcnt; /* received frames count */
- ushort hmask; /* user defined frm addr mask */
- ushort haddr1; /* user defined frm address 1 */
- ushort haddr2; /* user defined frm address 2 */
- ushort haddr3; /* user defined frm address 3 */
- ushort haddr4; /* user defined frm address 4 */
- ushort tmp; /* temp */
- ushort tmp_mb; /* temp */
-} hdlc_pram_t;
-
-/* CPM interrupts. There are nearly 32 interrupts generated by CPM
- * channels or devices. All of these are presented to the PPC core
- * as a single interrupt. The CPM interrupt handler dispatches its
- * own handlers, in a similar fashion to the PPC core handler. We
- * use the table as defined in the manuals (i.e. no special high
- * priority and SCC1 == SCCa, etc...).
- */
-#define CPMVEC_NR 32
-#define CPMVEC_OFFSET 0x00010000
-#define CPMVEC_PIO_PC15 ((ushort)0x1f | CPMVEC_OFFSET)
-#define CPMVEC_SCC1 ((ushort)0x1e | CPMVEC_OFFSET)
-#define CPMVEC_SCC2 ((ushort)0x1d | CPMVEC_OFFSET)
-#define CPMVEC_SCC3 ((ushort)0x1c | CPMVEC_OFFSET)
-#define CPMVEC_SCC4 ((ushort)0x1b | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC14 ((ushort)0x1a | CPMVEC_OFFSET)
-#define CPMVEC_TIMER1 ((ushort)0x19 | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC13 ((ushort)0x18 | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC12 ((ushort)0x17 | CPMVEC_OFFSET)
-#define CPMVEC_SDMA_CB_ERR ((ushort)0x16 | CPMVEC_OFFSET)
-#define CPMVEC_IDMA1 ((ushort)0x15 | CPMVEC_OFFSET)
-#define CPMVEC_IDMA2 ((ushort)0x14 | CPMVEC_OFFSET)
-#define CPMVEC_TIMER2 ((ushort)0x12 | CPMVEC_OFFSET)
-#define CPMVEC_RISCTIMER ((ushort)0x11 | CPMVEC_OFFSET)
-#define CPMVEC_I2C ((ushort)0x10 | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC11 ((ushort)0x0f | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC10 ((ushort)0x0e | CPMVEC_OFFSET)
-#define CPMVEC_TIMER3 ((ushort)0x0c | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC9 ((ushort)0x0b | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC8 ((ushort)0x0a | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC7 ((ushort)0x09 | CPMVEC_OFFSET)
-#define CPMVEC_TIMER4 ((ushort)0x07 | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC6 ((ushort)0x06 | CPMVEC_OFFSET)
-#define CPMVEC_SPI ((ushort)0x05 | CPMVEC_OFFSET)
-#define CPMVEC_SMC1 ((ushort)0x04 | CPMVEC_OFFSET)
-#define CPMVEC_SMC2 ((ushort)0x03 | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC5 ((ushort)0x02 | CPMVEC_OFFSET)
-#define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET)
-#define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET)
-
-extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id);
-
-/* CPM interrupt configuration vector.
-*/
-#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */
-#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */
-#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */
-#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */
-#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */
-#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */
-#define CICR_IEN ((uint)0x00000080) /* Int. enable */
-#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
-#endif /* __CPM_8XX__ */
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index ab4b060906bce83f7550ded4d4b651b00c8181a5..c66b26ff82df03196265d2d253956d3e7ad78b1c 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -139,7 +139,6 @@
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h
index b13809f88a1039f567c37d57c6b84c71a2d0e250..3a1d4d93885b36fd91d0189d40eed21e3719987c 100644
--- a/include/configs/MIP405.h
+++ b/include/configs/MIP405.h
@@ -306,7 +306,6 @@
#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET /* reset for ide supported... */
#define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h
index 393a02dd78c63bcba938015e71ec4ff0f067e9c3..1f5b9f045fb62f65a8c4a2d5123e3bbe382027ae 100644
--- a/include/configs/PIP405.h
+++ b/include/configs/PIP405.h
@@ -246,7 +246,6 @@
#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET /* reset for ide supported... */
#define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 78ce91d08985a3ec5617fc6aeb4270b5372ab174..b8f23d769c36a2774e7166704d22b33704d6f3f3 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -150,7 +150,6 @@
/*
* IDE/ATA stuff
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index e1f04459c45a71c98f706fb20f545674dc9e4275..2ba6b089cc6ef6ee3df4274e24fa1f0853d4abc5 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -584,9 +584,6 @@
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_RESET /* reset for ide supported */
diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
deleted file mode 100644
index 74636b9162830ca242ca8b5647c538add9d3eadf..0000000000000000000000000000000000000000
--- a/include/configs/TQM823L.h
+++ /dev/null
@@ -1,435 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_TQM823L 1 /* ...on a TQM8xxL module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#ifdef CONFIG_LCD /* with LCD controller ? */
-#define CONFIG_MPC8XX_LCD
-#define CONFIG_LCD_LOGO 1 /* print our logo on the LCD */
-#define CONFIG_LCD_INFO 1 /* ... and some board info */
-#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/
-#endif
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM823L\0" \
- "bootfile=TQM823L/uImage\0" \
- "fdt_addr=40040000\0" \
- "kernel_addr=40060000\0" \
- "ramdisk_addr=40200000\0" \
- "u-boot=TQM823L/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxL-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxL-0:256k(u-boot)," \
- "128k(dtb)," \
- "1664k(kernel)," \
- "2m(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h
deleted file mode 100644
index 6b345c427ccd71d7ccd693ce973fd339a8a0adbc..0000000000000000000000000000000000000000
--- a/include/configs/TQM823M.h
+++ /dev/null
@@ -1,434 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_TQM823M 1 /* ...on a TQM8xxM module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#ifdef CONFIG_LCD /* with LCD controller ? */
-#define CONFIG_MPC8XX_LCD
-/* #define CONFIG_NEC_NL6448BC20 1 / * use NEC NL6448BC20 display */
-#endif
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM823M\0" \
- "bootfile=TQM823M/uImage\0" \
- "fdt_addr=40080000\0" \
- "kernel_addr=400A0000\0" \
- "ramdisk_addr=40280000\0" \
- "u-boot=TQM823M/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
- "128k(dtb)," \
- "1920k(kernel)," \
- "5632(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h
deleted file mode 100644
index b4ed561544a006b5847026362ec1c43ec71a886f..0000000000000000000000000000000000000000
--- a/include/configs/TQM850L.h
+++ /dev/null
@@ -1,428 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
-#define CONFIG_TQM850L 1 /* ...on a TQM8xxL module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM850L\0" \
- "bootfile=TQM850L/uImage\0" \
- "fdt_addr=40040000\0" \
- "kernel_addr=40060000\0" \
- "ramdisk_addr=40200000\0" \
- "u-boot=TQM850L/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxL-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxL-0:256k(u-boot)," \
- "128k(dtb)," \
- "1664k(kernel)," \
- "2m(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h
deleted file mode 100644
index 1dc13295ff0a06a787e587ca284a1a59a9d2b95b..0000000000000000000000000000000000000000
--- a/include/configs/TQM850M.h
+++ /dev/null
@@ -1,429 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
-#define CONFIG_TQM850M 1 /* ...on a TQM8xxM module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM850M\0" \
- "bootfile=TQM850M/uImage\0" \
- "fdt_addr=40080000\0" \
- "kernel_addr=400A0000\0" \
- "ramdisk_addr=40280000\0" \
- "u-boot=TQM850M/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
- "128k(dtb)," \
- "1920k(kernel)," \
- "5632(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h
deleted file mode 100644
index b4c3a793874a73bbf4bb3f81d2a794d69f2da92d..0000000000000000000000000000000000000000
--- a/include/configs/TQM855L.h
+++ /dev/null
@@ -1,434 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC855 1 /* This is a MPC855 CPU */
-#define CONFIG_TQM855L 1 /* ...on a TQM8xxL module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM855L\0" \
- "bootfile=TQM855L/uImage\0" \
- "fdt_addr=40040000\0" \
- "kernel_addr=40060000\0" \
- "ramdisk_addr=40200000\0" \
- "u-boot=TQM855L/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxL-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxL-0:256k(u-boot)," \
- "128k(dtb)," \
- "1664k(kernel)," \
- "2m(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
deleted file mode 100644
index 14b76a66bcfa91c7887f3f8cc1695fefb063480f..0000000000000000000000000000000000000000
--- a/include/configs/TQM855M.h
+++ /dev/null
@@ -1,464 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC855 1 /* This is a MPC855 CPU */
-#define CONFIG_TQM855M 1 /* ...on a TQM8xxM module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM855M\0" \
- "bootfile=TQM855M/uImage\0" \
- "fdt_addr=40080000\0" \
- "kernel_addr=400A0000\0" \
- "ramdisk_addr=40280000\0" \
- "u-boot=TQM855M/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL 0x00000020 /* PB 26 */
-#define PB_SDA 0x00000010 /* PB 27 */
-
-#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
-#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
-#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */
-#if 0
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
- "128k(dtb)," \
- "1920k(kernel)," \
- "5632(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h
deleted file mode 100644
index f55fe56abbe179b384b1d549af118a569b56632d..0000000000000000000000000000000000000000
--- a/include/configs/TQM860L.h
+++ /dev/null
@@ -1,434 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
-#define CONFIG_TQM860L 1 /* ...on a TQM8xxL module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM860L\0" \
- "bootfile=TQM860L/uImage\0" \
- "fdt_addr=40040000\0" \
- "kernel_addr=40060000\0" \
- "ramdisk_addr=40200000\0" \
- "u-boot=TQM860L/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxL-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxL-0:256k(u-boot)," \
- "128k(dtb)," \
- "1664k(kernel)," \
- "2m(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
deleted file mode 100644
index 52c4d68693391f2473c7884cd294f00a193d6372..0000000000000000000000000000000000000000
--- a/include/configs/TQM860M.h
+++ /dev/null
@@ -1,438 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
-#define CONFIG_TQM860M 1 /* ...on a TQM8xxM module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM860M\0" \
- "bootfile=TQM860M/uImage\0" \
- "fdt_addr=400C0000\0" \
- "kernel_addr=40100000\0" \
- "ramdisk_addr=40280000\0" \
- "u-boot=TQM860M/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
- "128k(dtb)," \
- "1920k(kernel)," \
- "5632(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
deleted file mode 100644
index 06981c9861e8b7556009733a293204a480c272b7..0000000000000000000000000000000000000000
--- a/include/configs/TQM862L.h
+++ /dev/null
@@ -1,438 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860 1
-#define CONFIG_MPC860T 1
-#define CONFIG_MPC862 1
-
-#define CONFIG_TQM862L 1 /* ...on a TQM8xxL module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM862L\0" \
- "bootfile=TQM862L/uImage\0" \
- "fdt_addr=40040000\0" \
- "kernel_addr=40060000\0" \
- "ramdisk_addr=40200000\0" \
- "u-boot=TQM862L/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE+flash_info[0].size }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxL-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxL-0:256k(u-boot)," \
- "128k(dtb)," \
- "1664k(kernel)," \
- "2m(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- * 100 Mhz => 100.000.000 / Divider = 195
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h
deleted file mode 100644
index 3f87d8aa11a51bdfee382a48673c3e7b75a5558f..0000000000000000000000000000000000000000
--- a/include/configs/TQM862M.h
+++ /dev/null
@@ -1,439 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860 1
-#define CONFIG_MPC860T 1
-#define CONFIG_MPC862 1
-
-#define CONFIG_TQM862M 1 /* ...on a TQM8xxM module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM862M\0" \
- "bootfile=TQM862M/uImage\0" \
- "fdt_addr=40080000\0" \
- "kernel_addr=400A0000\0" \
- "ramdisk_addr=40280000\0" \
- "u-boot=TQM862M/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
- "128k(dtb)," \
- "1920k(kernel)," \
- "5632(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- * 100 Mhz => 100.000.000 / Divider = 195
- */
-
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
-#define CONFIG_SYS_MAMR_PTA 98
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
deleted file mode 100644
index 975f4b76dc6dceed537ed660395fa790a8dd2363..0000000000000000000000000000000000000000
--- a/include/configs/TQM866M.h
+++ /dev/null
@@ -1,457 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC866 1 /* This is a MPC866 CPU */
-#define CONFIG_TQM866M 1 /* ...on a TQM8xxM module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */
-#define CONFIG_SYS_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */
-#define CONFIG_SYS_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */
-#define CONFIG_8xx_CPUCLK_DEFAULT 50000000 /* 50 MHz - CPU default clock */
- /* (it will be used if there is no */
- /* 'cpuclk' variable with valid value) */
-
-#undef CONFIG_SYS_MEASURE_CPUCLK /* Measure real cpu clock */
- /* (function measure_gclk() */
- /* will be called) */
-#ifdef CONFIG_SYS_MEASURE_CPUCLK
-#define CONFIG_SYS_8XX_XIN 10000000 /* measure_gclk() needs this */
-#endif
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "hostname=TQM866M\0" \
- "bootfile=TQM866M/uImage\0" \
- "fdt_addr=400C0000\0" \
- "kernel_addr=40100000\0" \
- "ramdisk_addr=40280000\0" \
- "u-boot=TQM866M/u-image.bin\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=prot off 40000000 +${filesize};" \
- "era 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "sete filesize;save\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL 0x00000020 /* PB 26 */
-#define PB_SDA 0x00000010 /* PB 27 */
-
-#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
-#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
-#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C256 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */
-
-#define CONFIG_TIMESTAMP /* but print image timestmps */
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_NETCONSOLE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */
-
-/*-----------------------------------------------------------------------
- * Dynamic MTD partition support
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"
-
-#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
- "128k(dtb)," \
- "1920k(kernel)," \
- "5632(rootfs)," \
- "4m(data)"
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing: Default value of OR0 after reset
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
- OR_SCY_15_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- */
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
-
-/*
- * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
- *
- * CPUclock(MHz) * 31.2
- * CONFIG_SYS_MAMR_PTA = ----------------------------------- with DFBRG = 0
- * 2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
- *
- * CPU clock = 15 MHz: CONFIG_SYS_MAMR_PTA = 29 -> 4 * 7.73 us
- * CPU clock = 50 MHz: CONFIG_SYS_MAMR_PTA = 97 -> 4 * 7.76 us
- * CPU clock = 66 MHz: CONFIG_SYS_MAMR_PTA = 128 -> 4 * 7.75 us
- * CPU clock = 133 MHz: CONFIG_SYS_MAMR_PTA = 255 -> 4 * 7.67 us
- *
- * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
- * be met also in the default configuration, i.e. if environment variable
- * 'cpuclk' is not set.
- */
-#define CONFIG_SYS_MAMR_PTA 97
-
-/*
- * Memory Periodic Timer Prescaler Register (MPTPR) values.
- */
-/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16
-/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SCC1_ENET
-#define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
deleted file mode 100644
index 184cb62e19c66e7a4409bdb4de126c00ad4c507a..0000000000000000000000000000000000000000
--- a/include/configs/TQM885D.h
+++ /dev/null
@@ -1,451 +0,0 @@
-/*
- * (C) Copyright 2000-2014
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2006
- * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC885 1 /* This is a MPC885 CPU */
-#define CONFIG_TQM885D 1 /* ...on a TQM88D module */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */
-#define CONFIG_SYS_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */
-#define CONFIG_SYS_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */
-#define CONFIG_8xx_CPUCLK_DEFAULT 66000000 /* 66 MHz - CPU default clock */
- /* (it will be used if there is no */
- /* 'cpuclk' variable with valid value) */
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-#define CONFIG_BOOTCOUNT_LIMIT
-
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "bootfile=/tftpboot/TQM885D/uImage\0" \
- "fdt_addr=400C0000\0" \
- "kernel_addr=40100000\0" \
- "ramdisk_addr=40280000\0" \
- "load=tftp 200000 ${u-boot}\0" \
- "update=protect off 40000000 +${filesize};" \
- "erase 40000000 +${filesize};" \
- "cp.b 200000 40000000 ${filesize};" \
- "protect on 40000000 +${filesize}\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL 0x00000020 /* PB 26 */
-#define PB_SDA 0x00000010 /* PB 27 */
-
-#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
-#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
-#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C?? */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-# define CONFIG_RTC_DS1337 1
-# define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_RTC_MPC8xx /* MPC885 does not support RTC */
-
-#define CONFIG_TIMESTAMP /* but print image timestmps */
-
-/*
- * Command line configuration.
- */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0300000 /* 1 ... 3 MB in DRAM */
-#define CONFIG_SYS_ALT_MEMTEST /* alternate, more extensive
- memory test.*/
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing: Default value of OR0 after reset
- */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
- OR_SCY_6_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- */
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
-
-/*
- * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
- *
- * CPUclock(MHz) * 31.2
- * CONFIG_SYS_MAMR_PTA = ----------------------------------- with DFBRG = 0
- * 2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
- *
- * CPU clock = 15 MHz: CONFIG_SYS_MAMR_PTA = 29 -> 4 * 7.73 us
- * CPU clock = 50 MHz: CONFIG_SYS_MAMR_PTA = 97 -> 4 * 7.76 us
- * CPU clock = 66 MHz: CONFIG_SYS_MAMR_PTA = 128 -> 4 * 7.75 us
- * CPU clock = 133 MHz: CONFIG_SYS_MAMR_PTA = 255 -> 4 * 7.67 us
- *
- * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
- * be met also in the default configuration, i.e. if environment variable
- * 'cpuclk' is not set.
- */
-#define CONFIG_SYS_MAMR_PTA 128
-
-/*
- * Memory Periodic Timer Prescaler Register (MPTPR) values.
- */
-/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16
-/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-/*
- * Network configuration
- */
-#define CONFIG_SCC2_ENET /* enable ethernet on SCC2 */
-#define CONFIG_FEC_ENET /* enable ethernet on FEC */
-#define CONFIG_ETHER_ON_FEC1 /* ... for FEC1 */
-#define CONFIG_ETHER_ON_FEC2 /* ... for FEC2 */
-
-#if defined(CONFIG_CMD_MII)
-#define CONFIG_SYS_DISCOVER_PHY
-#define CONFIG_MII_INIT 1
-#endif
-
-#define CONFIG_NET_RETRY_COUNT 1 /* reduce max. timeout before
- switching to another netwok (if the
- tried network is unreachable) */
-
-#define CONFIG_ETHPRIME "SCC"
-
-#define CONFIG_HWCONFIG 1
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h
index 6a26269807e3a09343c206982e150889c75dfcd5..5ab063e5ceb2c7992727f386615c0e94d8ca4a6e 100644
--- a/include/configs/a4m072.h
+++ b/include/configs/a4m072.h
@@ -277,10 +277,6 @@
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_PREINIT
diff --git a/include/configs/aria.h b/include/configs/aria.h
index 0a7ef9919eba30dd5b36393e08b9c6cebe164737..3612e037b9fcb9f05610c30a3ce57544bbdefda5 100644
--- a/include/configs/aria.h
+++ b/include/configs/aria.h
@@ -532,8 +532,6 @@
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for IDE not supported */
#define CONFIG_IDE_RESET /* reset for IDE supported */
diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h
index d651eff4b2996a144801c8b39cb7dab8c4832bec..28165227944a3c2071f3a1d6a57f583f242ff273 100644
--- a/include/configs/inka4x0.h
+++ b/include/configs/inka4x0.h
@@ -285,10 +285,6 @@
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_PREINIT
diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h
index 68874dc0290d486c72ddc138f4ebcedc553b4954..736bebbe1cb9156cc22428504606082a07472036 100644
--- a/include/configs/manroland/mpc5200-common.h
+++ b/include/configs/manroland/mpc5200-common.h
@@ -140,9 +140,6 @@
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h
index e11a0e628a0be9e622a91a055cd11db0027e4f3a..a6aaf0e4ba2957358d296df3217a768b37dfba7c 100644
--- a/include/configs/mpc5121ads.h
+++ b/include/configs/mpc5121ads.h
@@ -538,9 +538,6 @@
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for IDE not supported */
#define CONFIG_IDE_RESET /* reset for IDE supported */
diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h
index 6da17be11cef26e4561bf28ae7cd4d87ff88e5a2..500277f7f0a8f14db92221602ea992596fc93eb4 100644
--- a/include/configs/pcm030.h
+++ b/include/configs/pcm030.h
@@ -346,8 +346,6 @@ IPB Bus clocking configuration.
IDE/ATA stuff Supports IDE harddisk
----------------------------------------------------------------------------*/
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_SYS_ATA_CS_ON_TIMER01
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
diff --git a/include/configs/v38b.h b/include/configs/v38b.h
index 2bd6cc11aeeedc90434cbaf96ad039deb532c9ee..c103215001c468fa7b2da43e5aa62781fce43871 100644
--- a/include/configs/v38b.h
+++ b/include/configs/v38b.h
@@ -232,8 +232,6 @@
/*
* IDE/ATA (supports IDE harddisk)
*/
-#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_RESET /* reset for ide supported */
diff --git a/include/i2c.h b/include/i2c.h
index 7726028044e32c4d2ebeb949283c4564d8cbd0ee..fe3dca09b86678a2a526d0fbda7b9efc75824b22 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -662,9 +662,6 @@ extern struct i2c_bus_hose i2c_bus[];
#ifndef I2C_SOFT_DECLARATIONS
# if defined(CONFIG_MPC8260)
# define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT);
-# elif defined(CONFIG_8xx)
-# define I2C_SOFT_DECLARATIONS volatile immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-
# elif (defined(CONFIG_AT91RM9200) || \
defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9261) || \
defined(CONFIG_AT91SAM9263))
@@ -674,15 +671,6 @@ extern struct i2c_bus_hose i2c_bus[];
# endif
#endif
-#ifdef CONFIG_8xx
-/* Set default value for the I2C bus speed on 8xx. In the
- * future, we'll define these in all 8xx board config files.
- */
-#ifndef CONFIG_SYS_I2C_SPEED
-#define CONFIG_SYS_I2C_SPEED 50000
-#endif
-#endif
-
/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
@@ -814,11 +802,6 @@ static inline u8 i2c_reg_read(u8 addr, u8 reg)
{
u8 buf;
-#ifdef CONFIG_8xx
- /* MPC8xx needs this. Maybe one day we can get rid of it. */
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
-
#ifdef DEBUG
printf("%s: addr=0x%02x, reg=0x%02x\n", __func__, addr, reg);
#endif
@@ -830,11 +813,6 @@ static inline u8 i2c_reg_read(u8 addr, u8 reg)
static inline void i2c_reg_write(u8 addr, u8 reg, u8 val)
{
-#ifdef CONFIG_8xx
- /* MPC8xx needs this. Maybe one day we can get rid of it. */
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
-
#ifdef DEBUG
printf("%s: addr=0x%02x, reg=0x%02x, val=0x%02x\n",
__func__, addr, reg, val);
diff --git a/include/lcd.h b/include/lcd.h
index f76fca77f9f57f03fd2a79bd4e54c470f7d0ee96..797d0b0de12b184056a71a2106f9c5c83c2f7949 100644
--- a/include/lcd.h
+++ b/include/lcd.h
@@ -40,9 +40,7 @@ void lcd_setcolreg(ushort regno, ushort red, ushort green, ushort blue);
*/
void lcd_set_flush_dcache(int flush);
-#if defined CONFIG_MPC823
-#include <mpc823_lcd.h>
-#elif defined(CONFIG_CPU_PXA25X) || defined(CONFIG_CPU_PXA27X) || \
+#if defined(CONFIG_CPU_PXA25X) || defined(CONFIG_CPU_PXA27X) || \
defined CONFIG_CPU_MONAHANS
#include <pxa_lcd.h>
#elif defined(CONFIG_ATMEL_LCD) || defined(CONFIG_ATMEL_HLCD)
diff --git a/include/mpc823_lcd.h b/include/mpc823_lcd.h
deleted file mode 100644
index cc72cde13f05ae69caeb06fd2679294d03982bc9..0000000000000000000000000000000000000000
--- a/include/mpc823_lcd.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * mpc823_lcd.h - MPC823 LCD Controller structures
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _MPC823_LCD_H_
-#define _MPC823_LCD_H_
-
-/*
- * LCD controller stucture for MPC823 CPU
- */
-typedef struct vidinfo {
- ushort vl_col; /* Number of columns (i.e. 640) */
- ushort vl_row; /* Number of rows (i.e. 480) */
- ushort vl_rot; /* Rotation of Display (0, 1, 2, 3) */
- ushort vl_width; /* Width of display area in millimeters */
- ushort vl_height; /* Height of display area in millimeters */
-
- /* LCD configuration register */
- u_char vl_clkp; /* Clock polarity */
- u_char vl_oep; /* Output Enable polarity */
- u_char vl_hsp; /* Horizontal Sync polarity */
- u_char vl_vsp; /* Vertical Sync polarity */
- u_char vl_dp; /* Data polarity */
- u_char vl_bpix; /* Bits per pixel, 0 = 1, 1 = 2, 2 = 4, 3 = 8 */
- u_char vl_lbw; /* LCD Bus width, 0 = 4, 1 = 8 */
- u_char vl_splt; /* Split display, 0 = single-scan, 1 = dual-scan */
- u_char vl_clor; /* Color, 0 = mono, 1 = color */
- u_char vl_tft; /* 0 = passive, 1 = TFT */
-
- /* Horizontal control register. Timing from data sheet */
- ushort vl_wbl; /* Wait between lines */
-
- /* Vertical control register */
- u_char vl_vpw; /* Vertical sync pulse width */
- u_char vl_lcdac; /* LCD AC timing */
- u_char vl_wbf; /* Wait between frames */
-} vidinfo_t;
-
-#endif
diff --git a/include/net.h b/include/net.h
index ed5259a80738214ed60a44d2ddf6ba51ac5565c4..2eaa88224c9050755330e67a57ae7b541cfaa3fa 100644
--- a/include/net.h
+++ b/include/net.h
@@ -12,10 +12,6 @@
#ifndef __NET_H__
#define __NET_H__
-#if defined(CONFIG_8xx)
-#include <commproc.h>
-#endif /* CONFIG_8xx */
-
#include <asm/cache.h>
#include <asm/byteorder.h> /* for nton* / ntoh* stuff */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index aaaf6511a86ff67936fe155b7d2f5307a010ed6a..94b54c210dfe5143cdda8cfd71c78ea0aca8424e 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -15,18 +15,10 @@
* Allow configuration to select PCMCIA slot,
* or try to generate a useful default
*/
-#if defined(CONFIG_CMD_PCMCIA) || \
- (defined(CONFIG_IDE) && \
- (defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_DIRECT) ) )
+#if defined(CONFIG_CMD_PCMCIA)
#if !defined(CONFIG_PCMCIA_SLOT_A) && !defined(CONFIG_PCMCIA_SLOT_B)
-
-#if defined(CONFIG_TQM8xxL)
-# define CONFIG_PCMCIA_SLOT_B /* The TQM8xxL use SLOT_B */
-#else
# error "PCMCIA Slot not configured"
-#endif
-
#endif /* !defined(CONFIG_PCMCIA_SLOT_A) && !defined(CONFIG_PCMCIA_SLOT_B) */
/* Make sure exactly one slot is defined - we support only one for now */
@@ -56,17 +48,6 @@
# define PCMCIA_SLOT_x PCMCIA_PSLOT_B
#endif
-/*
- * The TQM850L hardware has two pins swapped! Grrrrgh!
- */
-#ifdef CONFIG_TQM850L
-#define __MY_PCMCIA_GCRX_CXRESET PCMCIA_GCRX_CXOE
-#define __MY_PCMCIA_GCRX_CXOE PCMCIA_GCRX_CXRESET
-#else
-#define __MY_PCMCIA_GCRX_CXRESET PCMCIA_GCRX_CXRESET
-#define __MY_PCMCIA_GCRX_CXOE PCMCIA_GCRX_CXOE
-#endif
-
/*
* This structure is used to address each window in the PCMCIA controller.
*
@@ -263,13 +244,4 @@ typedef struct {
#endif
-#ifdef CONFIG_8xx
-extern u_int *pcmcia_pgcrx[];
-#define PCMCIA_PGCRX(slot) (*pcmcia_pgcrx[slot])
-#endif
-
-#if defined(CONFIG_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-extern int check_ide_device(int slot);
-#endif
-
#endif /* _PCMCIA_H */
diff --git a/include/post.h b/include/post.h
index 5ebd535823259e45215c90231d9ae110926370ec..d5b4062787b3dd92cb47cd9489f1c6d85e943361 100644
--- a/include/post.h
+++ b/include/post.h
@@ -29,10 +29,6 @@
#define _POST_WORD_ADDR \
(CONFIG_SYS_SRAM_BASE + CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-#elif defined(CONFIG_8xx)
-#define _POST_WORD_ADDR \
- (((immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_dpmem + CPM_POST_WORD_ADDR)
-
#elif defined(CONFIG_MPC8260)
#include <asm/cpm_8260.h>
#define _POST_WORD_ADDR (CONFIG_SYS_IMMR + CPM_POST_WORD_ADDR)
@@ -164,7 +160,6 @@ extern int memory_post_test(int flags);
#define CONFIG_SYS_POST_CACHE 0x00000020
#define CONFIG_SYS_POST_UART 0x00000040
#define CONFIG_SYS_POST_ETHER 0x00000080
-#define CONFIG_SYS_POST_SPI 0x00000100
#define CONFIG_SYS_POST_USB 0x00000200
#define CONFIG_SYS_POST_SPR 0x00000400
#define CONFIG_SYS_POST_SYSMON 0x00000800
diff --git a/include/ppc_asm.tmpl b/include/ppc_asm.tmpl
index 379c493919bf27f42b4835a6f9b2961ac1ab7da3..82884335edc21cc7cce44bd4bfa3c0af53b2b2fd 100644
--- a/include/ppc_asm.tmpl
+++ b/include/ppc_asm.tmpl
@@ -82,21 +82,6 @@
#define r31 31
-#if defined(CONFIG_8xx)
-
-/* Some special registers */
-
-#define ICR 148 /* Interrupt Cause Register (37-44) */
-#define DER 149
-#define COUNTA 150 /* Breakpoint Counter (37-44) */
-#define COUNTB 151 /* Breakpoint Counter (37-44) */
-#define LCTRL1 156 /* Load/Store Support (37-40) */
-#define LCTRL2 157 /* Load/Store Support (37-41) */
-#define ICTRL 158
-
-#endif /* CONFIG_8xx */
-
-
#if defined(CONFIG_5xx)
/* Some special purpose registers */
#define DER 149 /* Debug Enable Register */
@@ -108,36 +93,7 @@
#define EID 81
#endif /* CONFIG_5xx */
-#if defined(CONFIG_8xx)
-
-/* Registers in the processor's internal memory map that we use.
-*/
-#define SYPCR 0x00000004
-#define BR0 0x00000100
-#define OR0 0x00000104
-#define BR1 0x00000108
-#define OR1 0x0000010c
-#define BR2 0x00000110
-#define OR2 0x00000114
-#define BR3 0x00000118
-#define OR3 0x0000011c
-#define BR4 0x00000120
-#define OR4 0x00000124
-
-#define MAR 0x00000164
-#define MCR 0x00000168
-#define MAMR 0x00000170
-#define MBMR 0x00000174
-#define MSTAT 0x00000178
-#define MPTPR 0x0000017a
-#define MDR 0x0000017c
-
-#define TBSCR 0x00000200
-#define TBREFF0 0x00000204
-
-#define PLPRCR 0x00000284
-
-#elif defined(CONFIG_MPC8260)
+#if defined(CONFIG_MPC8260)
#define HID2 1011
diff --git a/include/status_led.h b/include/status_led.h
index f838f362dd7f5382c90d798c527f5fe47f26dbab..e37734696767940bdc9c0db8a9dc3dcfce0758fa 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -40,17 +40,8 @@ void status_led_init(void);
void status_led_tick (unsigned long timestamp);
void status_led_set (int led, int state);
-/***** TQM8xxL ********************************************************/
-#if defined(CONFIG_TQM8xxL)
-# define STATUS_LED_PAR im_cpm.cp_pbpar
-# define STATUS_LED_DIR im_cpm.cp_pbdir
-# define STATUS_LED_ODR im_cpm.cp_pbodr
-# define STATUS_LED_DAT im_cpm.cp_pbdat
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
/***** MVS v1 **********************************************************/
-#elif (defined(CONFIG_MVS) && CONFIG_MVS < 2)
+#if (defined(CONFIG_MVS) && CONFIG_MVS < 2)
# define STATUS_LED_PAR im_ioport.iop_pdpar
# define STATUS_LED_DIR im_ioport.iop_pddir
# undef STATUS_LED_ODR
diff --git a/include/usb/mpc8xx_udc.h b/include/usb/mpc8xx_udc.h
deleted file mode 100644
index 9906c75f6a2c37471a4254ad704de5c2d7eefab3..0000000000000000000000000000000000000000
--- a/include/usb/mpc8xx_udc.h
+++ /dev/null
@@ -1,178 +0,0 @@
-/*
- * Copyright (C) 2006 Bryan O'Donoghue, CodeHermit
- * bodonoghue@codehermit.ie
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <commproc.h>
-
-/* Mode Register */
-#define USMOD_EN 0x01
-#define USMOD_HOST 0x02
-#define USMOD_TEST 0x04
-#define USMOD_SFTE 0x08
-#define USMOD_RESUME 0x40
-#define USMOD_LSS 0x80
-
-/* Endpoint Registers */
-#define USEP_RHS_NORM 0x00
-#define USEP_RHS_IGNORE 0x01
-#define USEP_RHS_NAK 0x02
-#define USEP_RHS_STALL 0x03
-
-#define USEP_THS_NORM 0x00
-#define USEP_THS_IGNORE 0x04
-#define USEP_THS_NAK 0x08
-#define USEP_THS_STALL 0x0C
-
-#define USEP_RTE 0x10
-#define USEP_MF 0x20
-
-#define USEP_TM_CONTROL 0x00
-#define USEP_TM_INT 0x100
-#define USEP_TM_BULK 0x200
-#define USEP_TM_ISO 0x300
-
-/* Command Register */
-#define USCOM_EP0 0x00
-#define USCOM_EP1 0x01
-#define USCOM_EP2 0x02
-#define USCOM_EP3 0x03
-
-#define USCOM_FLUSH 0x40
-#define USCOM_STR 0x80
-
-/* Event Register */
-#define USB_E_RXB 0x0001
-#define USB_E_TXB 0x0002
-#define USB_E_BSY 0x0004
-#define USB_E_SOF 0x0008
-#define USB_E_TXE1 0x0010
-#define USB_E_TXE2 0x0020
-#define USB_E_TXE3 0x0040
-#define USB_E_TXE4 0x0080
-#define USB_TX_ERRMASK (USB_E_TXE1|USB_E_TXE2|USB_E_TXE3|USB_E_TXE4)
-#define USB_E_IDLE 0x0100
-#define USB_E_RESET 0x0200
-
-/* Mask Register */
-#define USBS_IDLE 0x01
-
-/* RX Buffer Descriptor */
-#define RX_BD_OV 0x02
-#define RX_BD_CR 0x04
-#define RX_BD_AB 0x08
-#define RX_BD_NO 0x10
-#define RX_BD_PID_DATA0 0x00
-#define RX_BD_PID_DATA1 0x40
-#define RX_BD_PID_SETUP 0x80
-#define RX_BD_F 0x400
-#define RX_BD_L 0x800
-#define RX_BD_I 0x1000
-#define RX_BD_W 0x2000
-#define RX_BD_E 0x8000
-
-/* Useful masks */
-#define RX_BD_PID_BITMASK (RX_BD_PID_DATA1 | RX_BD_PID_SETUP)
-#define STALL_BITMASK (USEP_THS_STALL | USEP_RHS_STALL)
-#define NAK_BITMASK (USEP_THS_NAK | USEP_RHS_NAK)
-#define CBD_TX_BITMASK (TX_BD_R | TX_BD_L | TX_BD_TC | TX_BD_I | TX_BD_CNF)
-
-/* TX Buffer Descriptor */
-#define TX_BD_UN 0x02
-#define TX_BD_TO 0x04
-#define TX_BD_NO_PID 0x00
-#define TX_BD_PID_DATA0 0x80
-#define TX_BD_PID_DATA1 0xC0
-#define TX_BD_CNF 0x200
-#define TX_BD_TC 0x400
-#define TX_BD_L 0x800
-#define TX_BD_I 0x1000
-#define TX_BD_W 0x2000
-#define TX_BD_R 0x8000
-
-/* Implementation specific defines */
-
-#define EP_MIN_PACKET_SIZE 0x08
-#define MAX_ENDPOINTS 0x04
-#define FIFO_SIZE 0x10
-#define EP_MAX_PKT FIFO_SIZE
-#define TX_RING_SIZE 0x04
-#define RX_RING_SIZE 0x06
-#define USB_MAX_PKT 0x40
-#define TOGGLE_TX_PID(x) x= ((~x)&0x40)|0x80
-#define TOGGLE_RX_PID(x) x^= 0x40
-#define EP_ATTACHED 0x01 /* Endpoint has a urb attached or not */
-#define EP_SEND_ZLP 0x02 /* Send ZLP y/n ? */
-
-#define PROFF_USB 0x00000000
-#define CPM_USB_BASE 0x00000A00
-
-/* UDC device defines */
-#define EP0_MAX_PACKET_SIZE EP_MAX_PKT
-
-#define UDC_OUT_PACKET_SIZE EP_MIN_PACKET_SIZE
-#define UDC_IN_PACKET_SIZE EP_MIN_PACKET_SIZE
-#define UDC_INT_PACKET_SIZE UDC_IN_PACKET_SIZE
-#define UDC_BULK_PACKET_SIZE EP_MIN_PACKET_SIZE
-
-struct mpc8xx_ep {
- struct urb * urb;
- unsigned char pid;
- unsigned char sc;
- volatile cbd_t * prx;
-};
-
-typedef struct mpc8xx_usb{
- char usmod; /* Mode Register */
- char usaddr; /* Slave Address Register */
- char uscom; /* Command Register */
- char res1; /* Reserved */
- ushort usep[4];
- ulong res2; /* Reserved */
- ushort usber; /* Event Register */
- ushort res3; /* Reserved */
- ushort usbmr; /* Mask Register */
- char res4; /* Reserved */
- char usbs; /* Status Register */
- char res5[8]; /* Reserved */
-}usb_t;
-
-typedef struct mpc8xx_parameter_ram{
- ushort ep0ptr; /* Endpoint Pointer Register 0 */
- ushort ep1ptr; /* Endpoint Pointer Register 1 */
- ushort ep2ptr; /* Endpoint Pointer Register 2 */
- ushort ep3ptr; /* Endpoint Pointer Register 3 */
- uint rstate; /* Receive state */
- uint rptr; /* Receive internal data pointer */
- ushort frame_n; /* Frame number */
- ushort rbcnt; /* Receive byte count */
- uint rtemp; /* Receive temp cp use only */
- uint rxusb; /* Rx Data Temp */
- ushort rxuptr; /* Rx microcode return address temp */
-}usb_pram_t;
-
-typedef struct endpoint_parameter_block_pointer{
- ushort rbase; /* RxBD base address */
- ushort tbase; /* TxBD base address */
- char rfcr; /* Rx Function code */
- char tfcr; /* Tx Function code */
- ushort mrblr; /* Maximum Receive Buffer Length */
- ushort rbptr; /* RxBD pointer Next Buffer Descriptor */
- ushort tbptr; /* TxBD pointer Next Buffer Descriptor */
- ulong tstate; /* Transmit internal state */
- ulong tptr; /* Transmit internal data pointer */
- ushort tcrc; /* Transmit temp CRC */
- ushort tbcnt; /* Transmit internal bye count */
- ulong ttemp; /* Tx temp */
- ushort txuptr; /* Tx microcode return address */
- ushort res1; /* Reserved */
-}usb_epb_t;
-
-typedef enum mpc8xx_udc_state{
- STATE_NOT_READY,
- STATE_ERROR,
- STATE_READY,
-}mpc8xx_udc_state_t;
-
diff --git a/include/watchdog.h b/include/watchdog.h
index 174c894e4993cd1c030391a111de782647673d1a..0055a837c3e3f6170153d9338ba9b2b83b449b15 100644
--- a/include/watchdog.h
+++ b/include/watchdog.h
@@ -72,11 +72,6 @@ int init_func_watchdog_reset(void);
* Prototypes from $(CPU)/cpu.c.
*/
-/* MPC 8xx */
-#if (defined(CONFIG_8xx) || defined(CONFIG_MPC860)) && !defined(__ASSEMBLY__)
- void reset_8xx_watchdog(volatile immap_t *immr);
-#endif
-
/* MPC 5xx */
#if defined(CONFIG_5xx) && !defined(__ASSEMBLY__)
void reset_5xx_watchdog(volatile immap_t *immr);
diff --git a/post/Makefile b/post/Makefile
index 78ede8c629088322f34b404a106a44aff8897c24..09bf408f4c271e03393ebc924f68a660acf640ce 100644
--- a/post/Makefile
+++ b/post/Makefile
@@ -11,7 +11,6 @@ obj-$(CONFIG_POST_STD_LIST) += tests.o
obj-y += drivers/
obj-$(CONFIG_PPC) += lib_powerpc/
obj-$(CONFIG_MPC83xx) += cpu/mpc83xx/
-obj-$(CONFIG_8xx) += cpu/mpc8xx/
obj-$(CONFIG_4xx) += cpu/ppc4xx/
ifneq ($(filter lwmon5 pdm360ng,$(BOARD)),)
obj-y += board/$(BOARD)/
diff --git a/post/cpu/mpc8xx/Makefile b/post/cpu/mpc8xx/Makefile
deleted file mode 100644
index f8bb6c9343fcf974417a0683098bbd396f186501..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2002-2007
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-$(CONFIG_HAS_POST) += cache_8xx.o
-obj-$(CONFIG_HAS_POST) += cache.o ether.o spr.o uart.o usb.o watchdog.o
diff --git a/post/cpu/mpc8xx/cache.c b/post/cpu/mpc8xx/cache.c
deleted file mode 100644
index af1281b759eaae7acaab05cc7b5f34ddfc14ccd2..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/cache.c
+++ /dev/null
@@ -1,62 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-/* Cache test
- *
- * This test verifies the CPU data and instruction cache using
- * several test scenarios.
- */
-
-#include <post.h>
-#include <watchdog.h>
-
-#if CONFIG_POST & CONFIG_SYS_POST_CACHE
-
-#define CACHE_POST_SIZE 1024
-
-extern int cache_post_test1 (char *, unsigned int);
-extern int cache_post_test2 (char *, unsigned int);
-extern int cache_post_test3 (char *, unsigned int);
-extern int cache_post_test4 (char *, unsigned int);
-extern int cache_post_test5 (void);
-extern int cache_post_test6 (void);
-
-int cache_post_test (int flags)
-{
- int ints = disable_interrupts ();
- int res = 0;
- static char ta[CACHE_POST_SIZE + 0xf];
- char *testarea = (char *) (((unsigned long) ta + 0xf) & ~0xf);
-
- WATCHDOG_RESET ();
- if (res == 0)
- res = cache_post_test1 (testarea, CACHE_POST_SIZE);
- WATCHDOG_RESET ();
- if (res == 0)
- res = cache_post_test2 (testarea, CACHE_POST_SIZE);
- WATCHDOG_RESET ();
- if (res == 0)
- res = cache_post_test3 (testarea, CACHE_POST_SIZE);
- WATCHDOG_RESET ();
- if (res == 0)
- res = cache_post_test4 (testarea, CACHE_POST_SIZE);
- WATCHDOG_RESET ();
- if (res == 0)
- res = cache_post_test5 ();
- WATCHDOG_RESET ();
- if (res == 0)
- res = cache_post_test6 ();
-
- WATCHDOG_RESET ();
- if (ints)
- enable_interrupts ();
- return res;
-}
-
-#endif /* CONFIG_POST & CONFIG_SYS_POST_CACHE */
diff --git a/post/cpu/mpc8xx/cache_8xx.S b/post/cpu/mpc8xx/cache_8xx.S
deleted file mode 100644
index 43649c8962b768997bad6950625a4f4d12446e84..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/cache_8xx.S
+++ /dev/null
@@ -1,477 +0,0 @@
-/*
- * Copyright (C) 2002 Wolfgang Denk <wd@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-
-#if defined(CONFIG_MPC823) || \
- defined(CONFIG_MPC850) || \
- defined(CONFIG_MPC855) || \
- defined(CONFIG_MPC860) || \
- defined(CONFIG_MPC862)
-
-#include <post.h>
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-#include <asm/cache.h>
-
-#if CONFIG_POST & CONFIG_SYS_POST_CACHE
-
- .text
-
-cache_post_dinvalidate:
- lis r10, IDC_INVALL@h
- mtspr DC_CST, r10
- blr
-
-cache_post_iinvalidate:
- lis r10, IDC_INVALL@h
- mtspr IC_CST, r10
- isync
- blr
-
-cache_post_ddisable:
- lis r10, IDC_DISABLE@h
- mtspr DC_CST, r10
- blr
-
-cache_post_dwb:
- lis r10, IDC_ENABLE@h
- mtspr DC_CST, r10
- lis r10, DC_CFWT@h
- mtspr DC_CST, r10
- blr
-
-cache_post_dwt:
- lis r10, IDC_ENABLE@h
- mtspr DC_CST, r10
- lis r10, DC_SFWT@h
- mtspr DC_CST, r10
- blr
-
-cache_post_idisable:
- lis r10, IDC_DISABLE@h
- mtspr IC_CST, r10
- isync
- blr
-
-cache_post_ienable:
- lis r10, IDC_ENABLE@h
- mtspr IC_CST, r10
- isync
- blr
-
-cache_post_iunlock:
- lis r10, IDC_UNALL@h
- mtspr IC_CST, r10
- isync
- blr
-
-cache_post_ilock:
- mtspr IC_ADR, r3
- lis r10, IDC_LDLCK@h
- mtspr IC_CST, r10
- isync
- blr
-
-/*
- * turn on the data cache
- * switch the data cache to write-back or write-through mode
- * invalidate the data cache
- * write the negative pattern to a cached area
- * read the area
- *
- * The negative pattern must be read at the last step
- */
- .global cache_post_test1
-cache_post_test1:
- mflr r0
- stw r0, 4(r1)
-
- stwu r3, -4(r1)
- stwu r4, -4(r1)
-
- bl cache_post_dwb
- bl cache_post_dinvalidate
-
- /* Write the negative pattern to the test area */
- lwz r0, 0(r1)
- mtctr r0
- li r0, 0xff
- lwz r3, 4(r1)
- subi r3, r3, 1
-1:
- stbu r0, 1(r3)
- bdnz 1b
-
- /* Read the test area */
- lwz r0, 0(r1)
- mtctr r0
- lwz r4, 4(r1)
- subi r4, r4, 1
- li r3, 0
-1:
- lbzu r0, 1(r4)
- cmpli cr0, r0, 0xff
- beq 2f
- li r3, -1
- b 3f
-2:
- bdnz 1b
-3:
-
- bl cache_post_ddisable
- bl cache_post_dinvalidate
-
- addi r1, r1, 8
-
- lwz r0, 4(r1)
- mtlr r0
- blr
-
-/*
- * turn on the data cache
- * switch the data cache to write-back or write-through mode
- * invalidate the data cache
- * write the zero pattern to a cached area
- * turn off the data cache
- * write the negative pattern to the area
- * turn on the data cache
- * read the area
- *
- * The negative pattern must be read at the last step
- */
- .global cache_post_test2
-cache_post_test2:
- mflr r0
- stw r0, 4(r1)
-
- stwu r3, -4(r1)
- stwu r4, -4(r1)
-
- bl cache_post_dwb
- bl cache_post_dinvalidate
-
- /* Write the zero pattern to the test area */
- lwz r0, 0(r1)
- mtctr r0
- li r0, 0
- lwz r3, 4(r1)
- subi r3, r3, 1
-1:
- stbu r0, 1(r3)
- bdnz 1b
-
- bl cache_post_ddisable
-
- /* Write the negative pattern to the test area */
- lwz r0, 0(r1)
- mtctr r0
- li r0, 0xff
- lwz r3, 4(r1)
- subi r3, r3, 1
-1:
- stbu r0, 1(r3)
- bdnz 1b
-
- bl cache_post_dwb
-
- /* Read the test area */
- lwz r0, 0(r1)
- mtctr r0
- lwz r4, 4(r1)
- subi r4, r4, 1
- li r3, 0
-1:
- lbzu r0, 1(r4)
- cmpli cr0, r0, 0xff
- beq 2f
- li r3, -1
- b 3f
-2:
- bdnz 1b
-3:
-
- bl cache_post_ddisable
- bl cache_post_dinvalidate
-
- addi r1, r1, 8
-
- lwz r0, 4(r1)
- mtlr r0
- blr
-
-/*
- * turn on the data cache
- * switch the data cache to write-through mode
- * invalidate the data cache
- * write the zero pattern to a cached area
- * flush the data cache
- * write the negative pattern to the area
- * turn off the data cache
- * read the area
- *
- * The negative pattern must be read at the last step
- */
- .global cache_post_test3
-cache_post_test3:
- mflr r0
- stw r0, 4(r1)
-
- stwu r3, -4(r1)
- stwu r4, -4(r1)
-
- bl cache_post_ddisable
- bl cache_post_dinvalidate
-
- /* Write the zero pattern to the test area */
- lwz r0, 0(r1)
- mtctr r0
- li r0, 0
- lwz r3, 4(r1)
- subi r3, r3, 1
-1:
- stbu r0, 1(r3)
- bdnz 1b
-
- bl cache_post_dwt
- bl cache_post_dinvalidate
-
- /* Write the negative pattern to the test area */
- lwz r0, 0(r1)
- mtctr r0
- li r0, 0xff
- lwz r3, 4(r1)
- subi r3, r3, 1
-1:
- stbu r0, 1(r3)
- bdnz 1b
-
- bl cache_post_ddisable
- bl cache_post_dinvalidate
-
- /* Read the test area */
- lwz r0, 0(r1)
- mtctr r0
- lwz r4, 4(r1)
- subi r4, r4, 1
- li r3, 0
-1:
- lbzu r0, 1(r4)
- cmpli cr0, r0, 0xff
- beq 2f
- li r3, -1
- b 3f
-2:
- bdnz 1b
-3:
-
- addi r1, r1, 8
-
- lwz r0, 4(r1)
- mtlr r0
- blr
-
-/*
- * turn on the data cache
- * switch the data cache to write-back mode
- * invalidate the data cache
- * write the negative pattern to a cached area
- * flush the data cache
- * write the zero pattern to the area
- * invalidate the data cache
- * read the area
- *
- * The negative pattern must be read at the last step
- */
- .global cache_post_test4
-cache_post_test4:
- mflr r0
- stw r0, 4(r1)
-
- stwu r3, -4(r1)
- stwu r4, -4(r1)
-
- bl cache_post_ddisable
- bl cache_post_dinvalidate
-
- /* Write the negative pattern to the test area */
- lwz r0, 0(r1)
- mtctr r0
- li r0, 0xff
- lwz r3, 4(r1)
- subi r3, r3, 1
-1:
- stbu r0, 1(r3)
- bdnz 1b
-
- bl cache_post_dwb
- bl cache_post_dinvalidate
-
- /* Write the zero pattern to the test area */
- lwz r0, 0(r1)
- mtctr r0
- li r0, 0
- lwz r3, 4(r1)
- subi r3, r3, 1
-1:
- stbu r0, 1(r3)
- bdnz 1b
-
- bl cache_post_ddisable
- bl cache_post_dinvalidate
-
- /* Read the test area */
- lwz r0, 0(r1)
- mtctr r0
- lwz r4, 4(r1)
- subi r4, r4, 1
- li r3, 0
-1:
- lbzu r0, 1(r4)
- cmpli cr0, r0, 0xff
- beq 2f
- li r3, -1
- b 3f
-2:
- bdnz 1b
-3:
-
- addi r1, r1, 8
-
- lwz r0, 4(r1)
- mtlr r0
- blr
-
-cache_post_test5_1:
- li r3, 0
-cache_post_test5_2:
- li r3, -1
-
-/*
- * turn on the instruction cache
- * unlock the entire instruction cache
- * invalidate the instruction cache
- * lock a branch instruction in the instruction cache
- * replace the branch instruction with "nop"
- * jump to the branch instruction
- * check that the branch instruction was executed
-*/
- .global cache_post_test5
-cache_post_test5:
- mflr r0
- stw r0, 4(r1)
-
- bl cache_post_ienable
- bl cache_post_iunlock
- bl cache_post_iinvalidate
-
- /* Compute r9 = cache_post_test5_reloc */
- bl cache_post_test5_reloc
-cache_post_test5_reloc:
- mflr r9
-
- /* Copy the test instruction to cache_post_test5_data */
- lis r3, (cache_post_test5_1 - cache_post_test5_reloc)@h
- ori r3, r3, (cache_post_test5_1 - cache_post_test5_reloc)@l
- add r3, r3, r9
- lis r4, (cache_post_test5_data - cache_post_test5_reloc)@h
- ori r4, r4, (cache_post_test5_data - cache_post_test5_reloc)@l
- add r4, r4, r9
- lwz r0, 0(r3)
- stw r0, 0(r4)
-
- bl cache_post_iinvalidate
-
- /* Lock the branch instruction */
- lis r3, (cache_post_test5_data - cache_post_test5_reloc)@h
- ori r3, r3, (cache_post_test5_data - cache_post_test5_reloc)@l
- add r3, r3, r9
- bl cache_post_ilock
-
- /* Replace the test instruction */
- lis r3, (cache_post_test5_2 - cache_post_test5_reloc)@h
- ori r3, r3, (cache_post_test5_2 - cache_post_test5_reloc)@l
- add r3, r3, r9
- lis r4, (cache_post_test5_data - cache_post_test5_reloc)@h
- ori r4, r4, (cache_post_test5_data - cache_post_test5_reloc)@l
- add r4, r4, r9
- lwz r0, 0(r3)
- stw r0, 0(r4)
-
- bl cache_post_iinvalidate
-
- /* Execute to the test instruction */
-cache_post_test5_data:
- nop
-
- bl cache_post_iunlock
-
- lwz r0, 4(r1)
- mtlr r0
- blr
-
-cache_post_test6_1:
- li r3, -1
-cache_post_test6_2:
- li r3, 0
-
-/*
- * turn on the instruction cache
- * unlock the entire instruction cache
- * invalidate the instruction cache
- * lock a branch instruction in the instruction cache
- * replace the branch instruction with "nop"
- * jump to the branch instruction
- * check that the branch instruction was executed
- */
- .global cache_post_test6
-cache_post_test6:
- mflr r0
- stw r0, 4(r1)
-
- bl cache_post_ienable
- bl cache_post_iunlock
- bl cache_post_iinvalidate
-
- /* Compute r9 = cache_post_test6_reloc */
- bl cache_post_test6_reloc
-cache_post_test6_reloc:
- mflr r9
-
- /* Copy the test instruction to cache_post_test6_data */
- lis r3, (cache_post_test6_1 - cache_post_test6_reloc)@h
- ori r3, r3, (cache_post_test6_1 - cache_post_test6_reloc)@l
- add r3, r3, r9
- lis r4, (cache_post_test6_data - cache_post_test6_reloc)@h
- ori r4, r4, (cache_post_test6_data - cache_post_test6_reloc)@l
- add r4, r4, r9
- lwz r0, 0(r3)
- stw r0, 0(r4)
-
- bl cache_post_iinvalidate
-
- /* Replace the test instruction */
- lis r3, (cache_post_test6_2 - cache_post_test6_reloc)@h
- ori r3, r3, (cache_post_test6_2 - cache_post_test6_reloc)@l
- add r3, r3, r9
- lis r4, (cache_post_test6_data - cache_post_test6_reloc)@h
- ori r4, r4, (cache_post_test6_data - cache_post_test6_reloc)@l
- add r4, r4, r9
- lwz r0, 0(r3)
- stw r0, 0(r4)
-
- bl cache_post_iinvalidate
-
- /* Execute to the test instruction */
-cache_post_test6_data:
- nop
-
- lwz r0, 4(r1)
- mtlr r0
- blr
-
-#endif /* CONFIG_MPC823 || MPC850 || MPC855 || MPC860 */
-#endif /* CONFIG_POST & CONFIG_SYS_POST_CACHE */
diff --git a/post/cpu/mpc8xx/ether.c b/post/cpu/mpc8xx/ether.c
deleted file mode 100644
index 47f6f32246586c8dff0350812bbce80e93886ef3..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/ether.c
+++ /dev/null
@@ -1,532 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-/*
- * Ethernet test
- *
- * The Serial Communication Controllers (SCC) listed in ctlr_list array below
- * are tested in the loopback ethernet mode.
- * The controllers are configured accordingly and several packets
- * are transmitted. The configurable test parameters are:
- * MIN_PACKET_LENGTH - minimum size of packet to transmit
- * MAX_PACKET_LENGTH - maximum size of packet to transmit
- * TEST_NUM - number of tests
- */
-
-#include <post.h>
-#if CONFIG_POST & CONFIG_SYS_POST_ETHER
-#if defined(CONFIG_8xx)
-#include <commproc.h>
-#elif defined(CONFIG_MPC8260)
-#include <asm/cpm_8260.h>
-#else
-#error "Apparently a bad configuration, please fix."
-#endif
-
-#include <command.h>
-#include <net.h>
-#include <serial.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define MIN_PACKET_LENGTH 64
-#define MAX_PACKET_LENGTH 256
-#define TEST_NUM 1
-
-#define CTLR_SCC 0
-
-extern void spi_init_f (void);
-extern void spi_init_r (void);
-
-/* The list of controllers to test */
-#if defined(CONFIG_MPC823)
-static int ctlr_list[][2] = { {CTLR_SCC, 1} };
-#else
-static int ctlr_list[][2] = { };
-#endif
-
-static struct {
- void (*init) (int index);
- void (*halt) (int index);
- int (*send) (int index, volatile void *packet, int length);
- int (*recv) (int index, void *packet, int length);
-} ctlr_proc[1];
-
-static char *ctlr_name[1] = { "SCC" };
-
-/* Ethernet Transmit and Receive Buffers */
-#define DBUF_LENGTH 1520
-
-#define TX_BUF_CNT 2
-
-#define TOUT_LOOP 100
-
-static char txbuf[DBUF_LENGTH];
-
-static uint rxIdx; /* index of the current RX buffer */
-static uint txIdx; /* index of the current TX buffer */
-
-/*
- * SCC Ethernet Tx and Rx buffer descriptors allocated at the
- * immr->udata_bd address on Dual-Port RAM
- * Provide for Double Buffering
- */
-
-typedef volatile struct CommonBufferDescriptor {
- cbd_t rxbd[PKTBUFSRX]; /* Rx BD */
- cbd_t txbd[TX_BUF_CNT]; /* Tx BD */
-} RTXBD;
-
-static RTXBD *rtx;
-
- /*
- * SCC callbacks
- */
-
-static void scc_init (int scc_index)
-{
- uchar ea[6];
-
- static int proff[] = {
- PROFF_SCC1,
- PROFF_SCC2,
- PROFF_SCC3,
- PROFF_SCC4,
- };
- static unsigned int cpm_cr[] = {
- CPM_CR_CH_SCC1,
- CPM_CR_CH_SCC2,
- CPM_CR_CH_SCC3,
- CPM_CR_CH_SCC4,
- };
-
- int i;
- scc_enet_t *pram_ptr;
-
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- immr->im_cpm.cp_scc[scc_index].scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
- pram_ptr = (scc_enet_t *) & (immr->im_cpm.cp_dparam[proff[scc_index]]);
-
- rxIdx = 0;
- txIdx = 0;
-
- rtx = (RTXBD *) (immr->im_cpm.cp_dpmem + CPM_SCC_BASE);
-
-#if 0
-
-#if (defined(PA_ENET_RXD) && defined(PA_ENET_TXD))
- /* Configure port A pins for Txd and Rxd.
- */
- immr->im_ioport.iop_papar |= (PA_ENET_RXD | PA_ENET_TXD);
- immr->im_ioport.iop_padir &= ~(PA_ENET_RXD | PA_ENET_TXD);
- immr->im_ioport.iop_paodr &= ~PA_ENET_TXD;
-#elif (defined(PB_ENET_RXD) && defined(PB_ENET_TXD))
- /* Configure port B pins for Txd and Rxd.
- */
- immr->im_cpm.cp_pbpar |= (PB_ENET_RXD | PB_ENET_TXD);
- immr->im_cpm.cp_pbdir &= ~(PB_ENET_RXD | PB_ENET_TXD);
- immr->im_cpm.cp_pbodr &= ~PB_ENET_TXD;
-#else
-#error Configuration Error: exactly ONE of PA_ENET_[RT]XD, PB_ENET_[RT]XD must be defined
-#endif
-
-#if defined(PC_ENET_LBK)
- /* Configure port C pins to disable External Loopback
- */
- immr->im_ioport.iop_pcpar &= ~PC_ENET_LBK;
- immr->im_ioport.iop_pcdir |= PC_ENET_LBK;
- immr->im_ioport.iop_pcso &= ~PC_ENET_LBK;
- immr->im_ioport.iop_pcdat &= ~PC_ENET_LBK; /* Disable Loopback */
-#endif /* PC_ENET_LBK */
-
- /* Configure port C pins to enable CLSN and RENA.
- */
- immr->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
- immr->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
- immr->im_ioport.iop_pcso |= (PC_ENET_CLSN | PC_ENET_RENA);
-
- /* Configure port A for TCLK and RCLK.
- */
- immr->im_ioport.iop_papar |= (PA_ENET_TCLK | PA_ENET_RCLK);
- immr->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
-
- /*
- * Configure Serial Interface clock routing -- see section 16.7.5.3
- * First, clear all SCC bits to zero, then set the ones we want.
- */
-
- immr->im_cpm.cp_sicr &= ~SICR_ENET_MASK;
- immr->im_cpm.cp_sicr |= SICR_ENET_CLKRT;
-#else
- /*
- * SCC2 receive clock is BRG2
- * SCC2 transmit clock is BRG3
- */
- immr->im_cpm.cp_brgc2 = 0x0001000C;
- immr->im_cpm.cp_brgc3 = 0x0001000C;
-
- immr->im_cpm.cp_sicr &= ~0x00003F00;
- immr->im_cpm.cp_sicr |= 0x00000a00;
-#endif /* 0 */
-
-
- /*
- * Initialize SDCR -- see section 16.9.23.7
- * SDMA configuration register
- */
- immr->im_siu_conf.sc_sdcr = 0x01;
-
-
- /*
- * Setup SCC Ethernet Parameter RAM
- */
-
- pram_ptr->sen_genscc.scc_rfcr = 0x18; /* Normal Operation and Mot byte ordering */
- pram_ptr->sen_genscc.scc_tfcr = 0x18; /* Mot byte ordering, Normal access */
-
- pram_ptr->sen_genscc.scc_mrblr = DBUF_LENGTH; /* max. ET package len 1520 */
-
- pram_ptr->sen_genscc.scc_rbase = (unsigned int) (&rtx->rxbd[0]); /* Set RXBD tbl start at Dual Port */
- pram_ptr->sen_genscc.scc_tbase = (unsigned int) (&rtx->txbd[0]); /* Set TXBD tbl start at Dual Port */
-
- /*
- * Setup Receiver Buffer Descriptors (13.14.24.18)
- * Settings:
- * Empty, Wrap
- */
-
- for (i = 0; i < PKTBUFSRX; i++) {
- rtx->rxbd[i].cbd_sc = BD_ENET_RX_EMPTY;
- rtx->rxbd[i].cbd_datlen = 0; /* Reset */
- rtx->rxbd[i].cbd_bufaddr = (uint) net_rx_packets[i];
- }
-
- rtx->rxbd[PKTBUFSRX - 1].cbd_sc |= BD_ENET_RX_WRAP;
-
- /*
- * Setup Ethernet Transmitter Buffer Descriptors (13.14.24.19)
- * Settings:
- * Add PADs to Short FRAMES, Wrap, Last, Tx CRC
- */
-
- for (i = 0; i < TX_BUF_CNT; i++) {
- rtx->txbd[i].cbd_sc =
- (BD_ENET_TX_PAD | BD_ENET_TX_LAST | BD_ENET_TX_TC);
- rtx->txbd[i].cbd_datlen = 0; /* Reset */
- rtx->txbd[i].cbd_bufaddr = (uint) (&txbuf[0]);
- }
-
- rtx->txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
-
- /*
- * Enter Command: Initialize Rx Params for SCC
- */
-
- do { /* Spin until ready to issue command */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
- /* Issue command */
- immr->im_cpm.cp_cpcr =
- ((CPM_CR_INIT_RX << 8) | (cpm_cr[scc_index] << 4) |
- CPM_CR_FLG);
- do { /* Spin until command processed */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
-
- /*
- * Ethernet Specific Parameter RAM
- * see table 13-16, pg. 660,
- * pg. 681 (example with suggested settings)
- */
-
- pram_ptr->sen_cpres = ~(0x0); /* Preset CRC */
- pram_ptr->sen_cmask = 0xdebb20e3; /* Constant Mask for CRC */
- pram_ptr->sen_crcec = 0x0; /* Error Counter CRC (unused) */
- pram_ptr->sen_alec = 0x0; /* Alignment Error Counter (unused) */
- pram_ptr->sen_disfc = 0x0; /* Discard Frame Counter (unused) */
- pram_ptr->sen_pads = 0x8888; /* Short Frame PAD Characters */
-
- pram_ptr->sen_retlim = 15; /* Retry Limit Threshold */
- pram_ptr->sen_maxflr = 1518; /* MAX Frame Length Register */
- pram_ptr->sen_minflr = 64; /* MIN Frame Length Register */
-
- pram_ptr->sen_maxd1 = DBUF_LENGTH; /* MAX DMA1 Length Register */
- pram_ptr->sen_maxd2 = DBUF_LENGTH; /* MAX DMA2 Length Register */
-
- pram_ptr->sen_gaddr1 = 0x0; /* Group Address Filter 1 (unused) */
- pram_ptr->sen_gaddr2 = 0x0; /* Group Address Filter 2 (unused) */
- pram_ptr->sen_gaddr3 = 0x0; /* Group Address Filter 3 (unused) */
- pram_ptr->sen_gaddr4 = 0x0; /* Group Address Filter 4 (unused) */
-
- eth_getenv_enetaddr("ethaddr", ea);
- pram_ptr->sen_paddrh = (ea[5] << 8) + ea[4];
- pram_ptr->sen_paddrm = (ea[3] << 8) + ea[2];
- pram_ptr->sen_paddrl = (ea[1] << 8) + ea[0];
-
- pram_ptr->sen_pper = 0x0; /* Persistence (unused) */
- pram_ptr->sen_iaddr1 = 0x0; /* Individual Address Filter 1 (unused) */
- pram_ptr->sen_iaddr2 = 0x0; /* Individual Address Filter 2 (unused) */
- pram_ptr->sen_iaddr3 = 0x0; /* Individual Address Filter 3 (unused) */
- pram_ptr->sen_iaddr4 = 0x0; /* Individual Address Filter 4 (unused) */
- pram_ptr->sen_taddrh = 0x0; /* Tmp Address (MSB) (unused) */
- pram_ptr->sen_taddrm = 0x0; /* Tmp Address (unused) */
- pram_ptr->sen_taddrl = 0x0; /* Tmp Address (LSB) (unused) */
-
- /*
- * Enter Command: Initialize Tx Params for SCC
- */
-
- do { /* Spin until ready to issue command */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
- /* Issue command */
- immr->im_cpm.cp_cpcr =
- ((CPM_CR_INIT_TX << 8) | (cpm_cr[scc_index] << 4) |
- CPM_CR_FLG);
- do { /* Spin until command processed */
- __asm__ ("eieio");
- } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
-
- /*
- * Mask all Events in SCCM - we use polling mode
- */
- immr->im_cpm.cp_scc[scc_index].scc_sccm = 0;
-
- /*
- * Clear Events in SCCE -- Clear bits by writing 1's
- */
-
- immr->im_cpm.cp_scc[scc_index].scc_scce = ~(0x0);
-
-
- /*
- * Initialize GSMR High 32-Bits
- * Settings: Normal Mode
- */
-
- immr->im_cpm.cp_scc[scc_index].scc_gsmrh = 0;
-
- /*
- * Initialize GSMR Low 32-Bits, but do not Enable Transmit/Receive
- * Settings:
- * TCI = Invert
- * TPL = 48 bits
- * TPP = Repeating 10's
- * LOOP = Loopback
- * MODE = Ethernet
- */
-
- immr->im_cpm.cp_scc[scc_index].scc_gsmrl = (SCC_GSMRL_TCI |
- SCC_GSMRL_TPL_48 |
- SCC_GSMRL_TPP_10 |
- SCC_GSMRL_DIAG_LOOP |
- SCC_GSMRL_MODE_ENET);
-
- /*
- * Initialize the DSR -- see section 13.14.4 (pg. 513) v0.4
- */
-
- immr->im_cpm.cp_scc[scc_index].scc_dsr = 0xd555;
-
- /*
- * Initialize the PSMR
- * Settings:
- * CRC = 32-Bit CCITT
- * NIB = Begin searching for SFD 22 bits after RENA
- * LPB = Loopback Enable (Needed when FDE is set)
- */
- immr->im_cpm.cp_scc[scc_index].scc_psmr = SCC_PSMR_ENCRC |
- SCC_PSMR_NIB22 | SCC_PSMR_LPB;
-
- /*
- * Set the ENT/ENR bits in the GSMR Low -- Enable Transmit/Receive
- */
-
- immr->im_cpm.cp_scc[scc_index].scc_gsmrl |=
- (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-}
-
-static void scc_halt (int scc_index)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- immr->im_cpm.cp_scc[scc_index].scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- immr->im_ioport.iop_pcso &= ~(PC_ENET_CLSN | PC_ENET_RENA);
-}
-
-static int scc_send (int index, volatile void *packet, int length)
-{
- int i, j = 0;
-
- while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j < TOUT_LOOP)) {
- udelay (1); /* will also trigger Wd if needed */
- j++;
- }
- if (j >= TOUT_LOOP)
- printf ("TX not ready\n");
- rtx->txbd[txIdx].cbd_bufaddr = (uint) packet;
- rtx->txbd[txIdx].cbd_datlen = length;
- rtx->txbd[txIdx].cbd_sc |=
- (BD_ENET_TX_READY | BD_ENET_TX_LAST | BD_ENET_TX_WRAP);
- while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j < TOUT_LOOP)) {
- udelay (1); /* will also trigger Wd if needed */
- j++;
- }
- if (j >= TOUT_LOOP)
- printf ("TX timeout\n");
- i = (rtx->txbd[txIdx].
- cbd_sc & BD_ENET_TX_STATS) /* return only status bits */ ;
- return i;
-}
-
-static int scc_recv (int index, void *packet, int max_length)
-{
- int length = -1;
-
- if (rtx->rxbd[rxIdx].cbd_sc & BD_ENET_RX_EMPTY) {
- goto Done; /* nothing received */
- }
-
- if (!(rtx->rxbd[rxIdx].cbd_sc & 0x003f)) {
- length = rtx->rxbd[rxIdx].cbd_datlen - 4;
- memcpy (packet,
- (void *)(net_rx_packets[rxIdx]),
- length < max_length ? length : max_length);
- }
-
- /* Give the buffer back to the SCC. */
- rtx->rxbd[rxIdx].cbd_datlen = 0;
-
- /* wrap around buffer index when necessary */
- if ((rxIdx + 1) >= PKTBUFSRX) {
- rtx->rxbd[PKTBUFSRX - 1].cbd_sc =
- (BD_ENET_RX_WRAP | BD_ENET_RX_EMPTY);
- rxIdx = 0;
- } else {
- rtx->rxbd[rxIdx].cbd_sc = BD_ENET_RX_EMPTY;
- rxIdx++;
- }
-
-Done:
- return length;
-}
-
- /*
- * Test routines
- */
-
-static void packet_fill (char *packet, int length)
-{
- char c = (char) length;
- int i;
-
- packet[0] = 0xFF;
- packet[1] = 0xFF;
- packet[2] = 0xFF;
- packet[3] = 0xFF;
- packet[4] = 0xFF;
- packet[5] = 0xFF;
-
- for (i = 6; i < length; i++) {
- packet[i] = c++;
- }
-}
-
-static int packet_check (char *packet, int length)
-{
- char c = (char) length;
- int i;
-
- for (i = 6; i < length; i++) {
- if (packet[i] != c++)
- return -1;
- }
-
- return 0;
-}
-
-static int test_ctlr (int ctlr, int index)
-{
- int res = -1;
- char packet_send[MAX_PACKET_LENGTH];
- char packet_recv[MAX_PACKET_LENGTH];
- int length;
- int i;
- int l;
-
- ctlr_proc[ctlr].init (index);
-
- for (i = 0; i < TEST_NUM; i++) {
- for (l = MIN_PACKET_LENGTH; l <= MAX_PACKET_LENGTH; l++) {
- packet_fill (packet_send, l);
-
- ctlr_proc[ctlr].send (index, packet_send, l);
-
- length = ctlr_proc[ctlr].recv (index, packet_recv,
- MAX_PACKET_LENGTH);
-
- if (length != l || packet_check (packet_recv, length) < 0) {
- goto Done;
- }
- }
- }
-
- res = 0;
-
-Done:
-
- ctlr_proc[ctlr].halt (index);
-
- /*
- * SCC2 Ethernet parameter RAM space overlaps
- * the SPI parameter RAM space. So we need to restore
- * the SPI configuration after SCC2 ethernet test.
- */
-#if defined(CONFIG_SPI)
- if (ctlr == CTLR_SCC && index == 1) {
- spi_init_f ();
- spi_init_r ();
- }
-#endif
-
- if (res != 0) {
- post_log ("ethernet %s%d test failed\n", ctlr_name[ctlr],
- index + 1);
- }
-
- return res;
-}
-
-int ether_post_test (int flags)
-{
- int res = 0;
- int i;
-
- ctlr_proc[CTLR_SCC].init = scc_init;
- ctlr_proc[CTLR_SCC].halt = scc_halt;
- ctlr_proc[CTLR_SCC].send = scc_send;
- ctlr_proc[CTLR_SCC].recv = scc_recv;
-
- for (i = 0; i < ARRAY_SIZE(ctlr_list); i++) {
- if (test_ctlr (ctlr_list[i][0], ctlr_list[i][1]) != 0) {
- res = -1;
- }
- }
-
-#if !defined(CONFIG_8xx_CONS_NONE)
- serial_reinit_all ();
-#endif
- return res;
-}
-
-#endif /* CONFIG_POST & CONFIG_SYS_POST_ETHER */
diff --git a/post/cpu/mpc8xx/spr.c b/post/cpu/mpc8xx/spr.c
deleted file mode 100644
index d20da8d1e84aba7da1c9e4a16b13c67a2788fec9..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/spr.c
+++ /dev/null
@@ -1,132 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-/*
- * SPR test
- *
- * The test checks the contents of Special Purpose Registers (SPR) listed
- * in the spr_test_list array below.
- * Each SPR value is read using mfspr instruction, some bits are masked
- * according to the table and the resulting value is compared to the
- * corresponding table value.
- */
-
-#include <post.h>
-
-#if CONFIG_POST & CONFIG_SYS_POST_SPR
-
-static struct
-{
- int number;
- char * name;
- unsigned long mask;
- unsigned long value;
-} spr_test_list [] = {
- /* Standard Special-Purpose Registers */
-
- {1, "XER", 0x00000000, 0x00000000},
- {8, "LR", 0x00000000, 0x00000000},
- {9, "CTR", 0x00000000, 0x00000000},
- {18, "DSISR", 0x00000000, 0x00000000},
- {19, "DAR", 0x00000000, 0x00000000},
- {22, "DEC", 0x00000000, 0x00000000},
- {26, "SRR0", 0x00000000, 0x00000000},
- {27, "SRR1", 0x00000000, 0x00000000},
- {272, "SPRG0", 0x00000000, 0x00000000},
- {273, "SPRG1", 0x00000000, 0x00000000},
- {274, "SPRG2", 0x00000000, 0x00000000},
- {275, "SPRG3", 0x00000000, 0x00000000},
- {287, "PVR", 0xFFFF0000, 0x00500000},
-
- /* Additional Special-Purpose Registers */
-
- {144, "CMPA", 0x00000000, 0x00000000},
- {145, "CMPB", 0x00000000, 0x00000000},
- {146, "CMPC", 0x00000000, 0x00000000},
- {147, "CMPD", 0x00000000, 0x00000000},
- {148, "ICR", 0xFFFFFFFF, 0x00000000},
- {149, "DER", 0x00000000, 0x00000000},
- {150, "COUNTA", 0xFFFFFFFF, 0x00000000},
- {151, "COUNTB", 0xFFFFFFFF, 0x00000000},
- {152, "CMPE", 0x00000000, 0x00000000},
- {153, "CMPF", 0x00000000, 0x00000000},
- {154, "CMPG", 0x00000000, 0x00000000},
- {155, "CMPH", 0x00000000, 0x00000000},
- {156, "LCTRL1", 0xFFFFFFFF, 0x00000000},
- {157, "LCTRL2", 0xFFFFFFFF, 0x00000000},
- {158, "ICTRL", 0xFFFFFFFF, 0x00000007},
- {159, "BAR", 0x00000000, 0x00000000},
- {630, "DPDR", 0x00000000, 0x00000000},
- {631, "DPIR", 0x00000000, 0x00000000},
- {638, "IMMR", 0xFFFF0000, CONFIG_SYS_IMMR },
- {560, "IC_CST", 0x8E380000, 0x00000000},
- {561, "IC_ADR", 0x00000000, 0x00000000},
- {562, "IC_DAT", 0x00000000, 0x00000000},
- {568, "DC_CST", 0xEF380000, 0x00000000},
- {569, "DC_ADR", 0x00000000, 0x00000000},
- {570, "DC_DAT", 0x00000000, 0x00000000},
- {784, "MI_CTR", 0xFFFFFFFF, 0x00000000},
- {786, "MI_AP", 0x00000000, 0x00000000},
- {787, "MI_EPN", 0x00000000, 0x00000000},
- {789, "MI_TWC", 0xFFFFFE02, 0x00000000},
- {790, "MI_RPN", 0x00000000, 0x00000000},
- {816, "MI_DBCAM", 0x00000000, 0x00000000},
- {817, "MI_DBRAM0", 0x00000000, 0x00000000},
- {818, "MI_DBRAM1", 0x00000000, 0x00000000},
- {792, "MD_CTR", 0xFFFFFFFF, 0x04000000},
- {793, "M_CASID", 0xFFFFFFF0, 0x00000000},
- {794, "MD_AP", 0x00000000, 0x00000000},
- {795, "MD_EPN", 0x00000000, 0x00000000},
- {796, "M_TWB", 0x00000003, 0x00000000},
- {797, "MD_TWC", 0x00000003, 0x00000000},
- {798, "MD_RPN", 0x00000000, 0x00000000},
- {799, "M_TW", 0x00000000, 0x00000000},
- {824, "MD_DBCAM", 0x00000000, 0x00000000},
- {825, "MD_DBRAM0", 0x00000000, 0x00000000},
- {826, "MD_DBRAM1", 0x00000000, 0x00000000},
-};
-
-static int spr_test_list_size = ARRAY_SIZE(spr_test_list);
-
-int spr_post_test (int flags)
-{
- int ret = 0;
- int ic = icache_status ();
- int i;
-
- unsigned long code[] = {
- 0x7c6002a6, /* mfspr r3,SPR */
- 0x4e800020 /* blr */
- };
- unsigned long (*get_spr) (void) = (void *) code;
-
- if (ic)
- icache_disable ();
-
- for (i = 0; i < spr_test_list_size; i++) {
- int num = spr_test_list[i].number;
-
- /* mfspr r3,num */
- code[0] = 0x7c6002a6 | ((num & 0x1F) << 16) | ((num & 0x3E0) << 6);
-
- if ((get_spr () & spr_test_list[i].mask) !=
- (spr_test_list[i].value & spr_test_list[i].mask)) {
- post_log ("The value of %s special register "
- "is incorrect: 0x%08X\n",
- spr_test_list[i].name, get_spr ());
- ret = -1;
- }
- }
-
- if (ic)
- icache_enable ();
-
- return ret;
-}
-#endif /* CONFIG_POST & CONFIG_SYS_POST_SPR */
diff --git a/post/cpu/mpc8xx/uart.c b/post/cpu/mpc8xx/uart.c
deleted file mode 100644
index 64ca7e4b98be5d41d4795f9eb8b8e91be555f87b..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/uart.c
+++ /dev/null
@@ -1,510 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-/*
- * UART test
- *
- * The Serial Management Controllers (SMC) and the Serial Communication
- * Controllers (SCC) listed in ctlr_list array below are tested in
- * the loopback UART mode.
- * The controllers are configured accordingly and several characters
- * are transmitted. The configurable test parameters are:
- * MIN_PACKET_LENGTH - minimum size of packet to transmit
- * MAX_PACKET_LENGTH - maximum size of packet to transmit
- * TEST_NUM - number of tests
- */
-
-#include <post.h>
-#if CONFIG_POST & CONFIG_SYS_POST_UART
-#if defined(CONFIG_8xx)
-#include <commproc.h>
-#elif defined(CONFIG_MPC8260)
-#include <asm/cpm_8260.h>
-#else
-#error "Apparently a bad configuration, please fix."
-#endif
-#include <command.h>
-#include <serial.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define CTLR_SMC 0
-#define CTLR_SCC 1
-
-/* The list of controllers to test */
-#if defined(CONFIG_MPC823)
-static int ctlr_list[][2] =
- { {CTLR_SMC, 0}, {CTLR_SMC, 1}, {CTLR_SCC, 1} };
-#else
-static int ctlr_list[][2] = { };
-#endif
-
-static struct {
- void (*init) (int index);
- void (*halt) (int index);
- void (*putc) (int index, const char c);
- int (*getc) (int index);
-} ctlr_proc[2];
-
-static char *ctlr_name[2] = { "SMC", "SCC" };
-
-static int proff_smc[] = { PROFF_SMC1, PROFF_SMC2 };
-static int proff_scc[] =
- { PROFF_SCC1, PROFF_SCC2, PROFF_SCC3, PROFF_SCC4 };
-
-/*
- * SMC callbacks
- */
-
-static void smc_init (int smc_index)
-{
- static int cpm_cr_ch[] = { CPM_CR_CH_SMC1, CPM_CR_CH_SMC2 };
-
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile smc_t *sp;
- volatile smc_uart_t *up;
- volatile cbd_t *tbdf, *rbdf;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- uint dpaddr;
-
- /* initialize pointers to SMC */
-
- sp = (smc_t *) & (cp->cp_smc[smc_index]);
- up = (smc_uart_t *) & cp->cp_dparam[proff_smc[smc_index]];
-
- /* Disable transmitter/receiver.
- */
- sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
-
- /* Enable SDMA.
- */
- im->im_siu_conf.sc_sdcr = 1;
-
- /* clear error conditions */
-#ifdef CONFIG_SYS_SDSR
- im->im_sdma.sdma_sdsr = CONFIG_SYS_SDSR;
-#else
- im->im_sdma.sdma_sdsr = 0x83;
-#endif
-
- /* clear SDMA interrupt mask */
-#ifdef CONFIG_SYS_SDMR
- im->im_sdma.sdma_sdmr = CONFIG_SYS_SDMR;
-#else
- im->im_sdma.sdma_sdmr = 0x00;
-#endif
-
- /* Set the physical address of the host memory buffers in
- * the buffer descriptors.
- */
- dpaddr = CPM_POST_BASE;
-
- /* Allocate space for two buffer descriptors in the DP ram.
- * For now, this address seems OK, but it may have to
- * change with newer versions of the firmware.
- * damm: allocating space after the two buffers for rx/tx data
- */
-
- rbdf = (cbd_t *) & cp->cp_dpmem[dpaddr];
- rbdf->cbd_bufaddr = (uint) (rbdf + 2);
- rbdf->cbd_sc = 0;
- tbdf = rbdf + 1;
- tbdf->cbd_bufaddr = ((uint) (rbdf + 2)) + 1;
- tbdf->cbd_sc = 0;
-
- /* Set up the uart parameters in the parameter ram.
- */
- up->smc_rbase = dpaddr;
- up->smc_tbase = dpaddr + sizeof (cbd_t);
- up->smc_rfcr = SMC_EB;
- up->smc_tfcr = SMC_EB;
-
- /* Set UART mode, 8 bit, no parity, one stop.
- * Enable receive and transmit.
- * Set local loopback mode.
- */
- sp->smc_smcmr = smcr_mk_clen (9) | SMCMR_SM_UART | (ushort) 0x0004;
-
- /* Mask all interrupts and remove anything pending.
- */
- sp->smc_smcm = 0;
- sp->smc_smce = 0xff;
-
- /* Set up the baud rate generator.
- */
- cp->cp_simode = 0x00000000;
-
- cp->cp_brgc1 =
- (((gd->cpu_clk / 16 / gd->baudrate) -
- 1) << 1) | CPM_BRG_EN;
-
- /* Make the first buffer the only buffer.
- */
- tbdf->cbd_sc |= BD_SC_WRAP;
- rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
-
- /* Single character receive.
- */
- up->smc_mrblr = 1;
- up->smc_maxidl = 0;
-
- /* Initialize Tx/Rx parameters.
- */
-
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- cp->cp_cpcr =
- mk_cr_cmd (cpm_cr_ch[smc_index], CPM_CR_INIT_TRX) | CPM_CR_FLG;
-
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- /* Enable transmitter/receiver.
- */
- sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
-}
-
-static void smc_halt(int smc_index)
-{
-}
-
-static void smc_putc (int smc_index, const char c)
-{
- volatile cbd_t *tbdf;
- volatile char *buf;
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
-
- up = (smc_uart_t *) & cpmp->cp_dparam[proff_smc[smc_index]];
-
- tbdf = (cbd_t *) & cpmp->cp_dpmem[up->smc_tbase];
-
- /* Wait for last character to go.
- */
-
- buf = (char *) tbdf->cbd_bufaddr;
-#if 0
- __asm__ ("eieio");
- while (tbdf->cbd_sc & BD_SC_READY)
- __asm__ ("eieio");
-#endif
-
- *buf = c;
- tbdf->cbd_datlen = 1;
- tbdf->cbd_sc |= BD_SC_READY;
- __asm__ ("eieio");
-#if 1
- while (tbdf->cbd_sc & BD_SC_READY)
- __asm__ ("eieio");
-#endif
-}
-
-static int smc_getc (int smc_index)
-{
- volatile cbd_t *rbdf;
- volatile unsigned char *buf;
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
- unsigned char c;
- int i;
-
- up = (smc_uart_t *) & cpmp->cp_dparam[proff_smc[smc_index]];
-
- rbdf = (cbd_t *) & cpmp->cp_dpmem[up->smc_rbase];
-
- /* Wait for character to show up.
- */
- buf = (unsigned char *) rbdf->cbd_bufaddr;
-#if 0
- while (rbdf->cbd_sc & BD_SC_EMPTY);
-#else
- for (i = 100; i > 0; i--) {
- if (!(rbdf->cbd_sc & BD_SC_EMPTY))
- break;
- udelay (1000);
- }
-
- if (i == 0)
- return -1;
-#endif
- c = *buf;
- rbdf->cbd_sc |= BD_SC_EMPTY;
-
- return (c);
-}
-
- /*
- * SCC callbacks
- */
-
-static void scc_init (int scc_index)
-{
- static int cpm_cr_ch[] = {
- CPM_CR_CH_SCC1,
- CPM_CR_CH_SCC2,
- CPM_CR_CH_SCC3,
- CPM_CR_CH_SCC4,
- };
-
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile scc_t *sp;
- volatile scc_uart_t *up;
- volatile cbd_t *tbdf, *rbdf;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- uint dpaddr;
-
- /* initialize pointers to SCC */
-
- sp = (scc_t *) & (cp->cp_scc[scc_index]);
- up = (scc_uart_t *) & cp->cp_dparam[proff_scc[scc_index]];
-
- /* Disable transmitter/receiver.
- */
- sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-
- dpaddr = CPM_POST_BASE;
-
- /* Enable SDMA.
- */
- im->im_siu_conf.sc_sdcr = 0x0001;
-
- /* Set the physical address of the host memory buffers in
- * the buffer descriptors.
- */
-
- rbdf = (cbd_t *) & cp->cp_dpmem[dpaddr];
- rbdf->cbd_bufaddr = (uint) (rbdf + 2);
- rbdf->cbd_sc = 0;
- tbdf = rbdf + 1;
- tbdf->cbd_bufaddr = ((uint) (rbdf + 2)) + 1;
- tbdf->cbd_sc = 0;
-
- /* Set up the baud rate generator.
- */
- cp->cp_sicr &= ~(0x000000FF << (8 * scc_index));
- /* no |= needed, since BRG1 is 000 */
-
- cp->cp_brgc1 =
- (((gd->cpu_clk / 16 / gd->baudrate) -
- 1) << 1) | CPM_BRG_EN;
-
- /* Set up the uart parameters in the parameter ram.
- */
- up->scc_genscc.scc_rbase = dpaddr;
- up->scc_genscc.scc_tbase = dpaddr + sizeof (cbd_t);
-
- /* Initialize Tx/Rx parameters.
- */
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
- cp->cp_cpcr =
- mk_cr_cmd (cpm_cr_ch[scc_index], CPM_CR_INIT_TRX) | CPM_CR_FLG;
-
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- up->scc_genscc.scc_rfcr = SCC_EB | 0x05;
- up->scc_genscc.scc_tfcr = SCC_EB | 0x05;
-
- up->scc_genscc.scc_mrblr = 1; /* Single character receive */
- up->scc_maxidl = 0; /* disable max idle */
- up->scc_brkcr = 1; /* send one break character on stop TX */
- up->scc_parec = 0;
- up->scc_frmec = 0;
- up->scc_nosec = 0;
- up->scc_brkec = 0;
- up->scc_uaddr1 = 0;
- up->scc_uaddr2 = 0;
- up->scc_toseq = 0;
- up->scc_char1 = 0x8000;
- up->scc_char2 = 0x8000;
- up->scc_char3 = 0x8000;
- up->scc_char4 = 0x8000;
- up->scc_char5 = 0x8000;
- up->scc_char6 = 0x8000;
- up->scc_char7 = 0x8000;
- up->scc_char8 = 0x8000;
- up->scc_rccm = 0xc0ff;
-
- /* Set low latency / small fifo.
- */
- sp->scc_gsmrh = SCC_GSMRH_RFW;
-
- /* Set UART mode
- */
- sp->scc_gsmrl &= ~0xF;
- sp->scc_gsmrl |= SCC_GSMRL_MODE_UART;
-
- /* Set local loopback mode.
- */
- sp->scc_gsmrl &= ~SCC_GSMRL_DIAG_LE;
- sp->scc_gsmrl |= SCC_GSMRL_DIAG_LOOP;
-
- /* Set clock divider 16 on Tx and Rx
- */
- sp->scc_gsmrl |= (SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
-
- sp->scc_psmr |= SCU_PSMR_CL;
-
- /* Mask all interrupts and remove anything pending.
- */
- sp->scc_sccm = 0;
- sp->scc_scce = 0xffff;
- sp->scc_dsr = 0x7e7e;
- sp->scc_psmr = 0x3000;
-
- /* Make the first buffer the only buffer.
- */
- tbdf->cbd_sc |= BD_SC_WRAP;
- rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
-
- /* Enable transmitter/receiver.
- */
- sp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-}
-
-static void scc_halt(int scc_index)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- volatile scc_t *sp = (scc_t *) & (cp->cp_scc[scc_index]);
-
- sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT | SCC_GSMRL_DIAG_LE);
-}
-
-static void scc_putc (int scc_index, const char c)
-{
- volatile cbd_t *tbdf;
- volatile char *buf;
- volatile scc_uart_t *up;
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
-
- up = (scc_uart_t *) & cpmp->cp_dparam[proff_scc[scc_index]];
-
- tbdf = (cbd_t *) & cpmp->cp_dpmem[up->scc_genscc.scc_tbase];
-
- /* Wait for last character to go.
- */
-
- buf = (char *) tbdf->cbd_bufaddr;
-#if 0
- __asm__ ("eieio");
- while (tbdf->cbd_sc & BD_SC_READY)
- __asm__ ("eieio");
-#endif
-
- *buf = c;
- tbdf->cbd_datlen = 1;
- tbdf->cbd_sc |= BD_SC_READY;
- __asm__ ("eieio");
-#if 1
- while (tbdf->cbd_sc & BD_SC_READY)
- __asm__ ("eieio");
-#endif
-}
-
-static int scc_getc (int scc_index)
-{
- volatile cbd_t *rbdf;
- volatile unsigned char *buf;
- volatile scc_uart_t *up;
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
- unsigned char c;
- int i;
-
- up = (scc_uart_t *) & cpmp->cp_dparam[proff_scc[scc_index]];
-
- rbdf = (cbd_t *) & cpmp->cp_dpmem[up->scc_genscc.scc_rbase];
-
- /* Wait for character to show up.
- */
- buf = (unsigned char *) rbdf->cbd_bufaddr;
-#if 0
- while (rbdf->cbd_sc & BD_SC_EMPTY);
-#else
- for (i = 100; i > 0; i--) {
- if (!(rbdf->cbd_sc & BD_SC_EMPTY))
- break;
- udelay (1000);
- }
-
- if (i == 0)
- return -1;
-#endif
- c = *buf;
- rbdf->cbd_sc |= BD_SC_EMPTY;
-
- return (c);
-}
-
- /*
- * Test routines
- */
-
-static int test_ctlr (int ctlr, int index)
-{
- int res = -1;
- char test_str[] = "*** UART Test String ***\r\n";
- int i;
-
- ctlr_proc[ctlr].init (index);
-
- for (i = 0; i < sizeof (test_str) - 1; i++) {
- ctlr_proc[ctlr].putc (index, test_str[i]);
- if (ctlr_proc[ctlr].getc (index) != test_str[i])
- goto Done;
- }
-
- res = 0;
-
-Done:
- ctlr_proc[ctlr].halt (index);
-
- if (res != 0) {
- post_log ("uart %s%d test failed\n",
- ctlr_name[ctlr], index + 1);
- }
-
- return res;
-}
-
-int uart_post_test (int flags)
-{
- int res = 0;
- int i;
-
- ctlr_proc[CTLR_SMC].init = smc_init;
- ctlr_proc[CTLR_SMC].halt = smc_halt;
- ctlr_proc[CTLR_SMC].putc = smc_putc;
- ctlr_proc[CTLR_SMC].getc = smc_getc;
-
- ctlr_proc[CTLR_SCC].init = scc_init;
- ctlr_proc[CTLR_SCC].halt = scc_halt;
- ctlr_proc[CTLR_SCC].putc = scc_putc;
- ctlr_proc[CTLR_SCC].getc = scc_getc;
-
- for (i = 0; i < ARRAY_SIZE(ctlr_list); i++) {
- if (test_ctlr (ctlr_list[i][0], ctlr_list[i][1]) != 0) {
- res = -1;
- }
- }
-
-#if !defined(CONFIG_8xx_CONS_NONE)
- serial_reinit_all ();
-#endif
-
- return res;
-}
-
-#endif /* CONFIG_POST & CONFIG_SYS_POST_UART */
diff --git a/post/cpu/mpc8xx/usb.c b/post/cpu/mpc8xx/usb.c
deleted file mode 100644
index 6334088ea4bb8443b028c127c46ec481312d8404..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/usb.c
+++ /dev/null
@@ -1,249 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-/*
- * USB test
- *
- * The USB controller is tested in the local loopback mode.
- * It is configured so that endpoint 0 operates as host and endpoint 1
- * operates as function endpoint. After that an IN token transaction
- * is performed.
- * Refer to MPC850 User Manual, Section 32.11.1 USB Host Controller
- * Initialization Example.
- */
-
-#include <post.h>
-
-#if CONFIG_POST & CONFIG_SYS_POST_USB
-
-#include <commproc.h>
-#include <command.h>
-
-#define TOUT_LOOP 100
-
-#define PROFF_USB ((uint)0x0000)
-
-#define CPM_USB_EP0_BASE 0x0a00
-#define CPM_USB_EP1_BASE 0x0a20
-
-#define CPM_USB_DT0_BASE 0x0a80
-#define CPM_USB_DT1_BASE 0x0a90
-#define CPM_USB_DR0_BASE 0x0aa0
-#define CPM_USB_DR1_BASE 0x0ab0
-
-#define CPM_USB_RX0_BASE 0x0b00
-#define CPM_USB_RX1_BASE 0x0b08
-#define CPM_USB_TX0_BASE 0x0b20
-#define CPM_USB_TX1_BASE 0x0b28
-
-#define USB_EXPECT(x) if (!(x)) goto Done;
-
-typedef struct usb_param {
- ushort ep0ptr;
- ushort ep1ptr;
- ushort ep2ptr;
- ushort ep3ptr;
- uint rstate;
- uint rptr;
- ushort frame_n;
- ushort rbcnt;
- ushort rtemp;
-} usb_param_t;
-
-typedef struct usb_param_block {
- ushort rbase;
- ushort tbase;
- uchar rfcr;
- uchar tfcr;
- ushort mrblr;
- ushort rbptr;
- ushort tbptr;
- uint tstate;
- uint tptr;
- ushort tcrc;
- ushort tbcnt;
- uint res[2];
-} usb_param_block_t;
-
-typedef struct usb {
- uchar usmod;
- uchar usadr;
- uchar uscom;
- uchar res1;
- ushort usep[4];
- uchar res2[4];
- ushort usber;
- uchar res3[2];
- ushort usbmr;
- uchar res4;
- uchar usbs;
- uchar res5[8];
-} usb_t;
-
-int usb_post_test (int flags)
-{
- int res = -1;
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- volatile usb_param_t *pram_ptr;
- uint dpram;
- ushort DPRAM;
- volatile cbd_t *tx;
- volatile cbd_t *rx;
- volatile usb_t *usbr;
- volatile usb_param_block_t *ep0;
- volatile usb_param_block_t *ep1;
- int j;
-
- pram_ptr = (usb_param_t *) & (im->im_cpm.cp_dparam[PROFF_USB]);
- dpram = (uint) im->im_cpm.cp_dpmem;
- DPRAM = dpram;
- tx = (cbd_t *) (dpram + CPM_USB_TX0_BASE);
- rx = (cbd_t *) (dpram + CPM_USB_RX0_BASE);
- ep0 = (usb_param_block_t *) (dpram + CPM_USB_EP0_BASE);
- ep1 = (usb_param_block_t *) (dpram + CPM_USB_EP1_BASE);
- usbr = (usb_t *) & (im->im_cpm.cp_scc[0]);
-
- /* 01 */
- im->im_ioport.iop_padir &= ~(ushort) 0x0200;
- im->im_ioport.iop_papar |= (ushort) 0x0200;
-
- cp->cp_sicr &= ~0x000000FF;
- cp->cp_sicr |= 0x00000018;
-
- cp->cp_brgc4 = 0x00010001;
-
- /* 02 */
- im->im_ioport.iop_padir &= ~(ushort) 0x0002;
- im->im_ioport.iop_padir &= ~(ushort) 0x0001;
-
- im->im_ioport.iop_papar |= (ushort) 0x0002;
- im->im_ioport.iop_papar |= (ushort) 0x0001;
-
- /* 03 */
- im->im_ioport.iop_pcdir &= ~(ushort) 0x0020;
- im->im_ioport.iop_pcdir &= ~(ushort) 0x0010;
-
- im->im_ioport.iop_pcpar &= ~(ushort) 0x0020;
- im->im_ioport.iop_pcpar &= ~(ushort) 0x0010;
-
- im->im_ioport.iop_pcso |= (ushort) 0x0020;
- im->im_ioport.iop_pcso |= (ushort) 0x0010;
-
- /* 04 */
- im->im_ioport.iop_pcdir |= (ushort) 0x0200;
- im->im_ioport.iop_pcdir |= (ushort) 0x0100;
-
- im->im_ioport.iop_pcpar |= (ushort) 0x0200;
- im->im_ioport.iop_pcpar |= (ushort) 0x0100;
-
- /* 05 */
- pram_ptr->frame_n = 0;
-
- /* 06 */
- pram_ptr->ep0ptr = DPRAM + CPM_USB_EP0_BASE;
- pram_ptr->ep1ptr = DPRAM + CPM_USB_EP1_BASE;
-
- /* 07-10 */
- tx[0].cbd_sc = 0xB800;
- tx[0].cbd_datlen = 3;
- tx[0].cbd_bufaddr = dpram + CPM_USB_DT0_BASE;
-
- tx[1].cbd_sc = 0xBC80;
- tx[1].cbd_datlen = 3;
- tx[1].cbd_bufaddr = dpram + CPM_USB_DT1_BASE;
-
- rx[0].cbd_sc = 0xA000;
- rx[0].cbd_datlen = 0;
- rx[0].cbd_bufaddr = dpram + CPM_USB_DR0_BASE;
-
- rx[1].cbd_sc = 0xA000;
- rx[1].cbd_datlen = 0;
- rx[1].cbd_bufaddr = dpram + CPM_USB_DR1_BASE;
-
- /* 11-12 */
- *(volatile int *) (dpram + CPM_USB_DT0_BASE) = 0x69856000;
- *(volatile int *) (dpram + CPM_USB_DT1_BASE) = 0xABCD1234;
-
- *(volatile int *) (dpram + CPM_USB_DR0_BASE) = 0;
- *(volatile int *) (dpram + CPM_USB_DR1_BASE) = 0;
-
- /* 13-16 */
- ep0->rbase = DPRAM + CPM_USB_RX0_BASE;
- ep0->tbase = DPRAM + CPM_USB_TX0_BASE;
- ep0->rfcr = 0x18;
- ep0->tfcr = 0x18;
- ep0->mrblr = 0x100;
- ep0->rbptr = DPRAM + CPM_USB_RX0_BASE;
- ep0->tbptr = DPRAM + CPM_USB_TX0_BASE;
- ep0->tstate = 0;
-
- /* 17-20 */
- ep1->rbase = DPRAM + CPM_USB_RX1_BASE;
- ep1->tbase = DPRAM + CPM_USB_TX1_BASE;
- ep1->rfcr = 0x18;
- ep1->tfcr = 0x18;
- ep1->mrblr = 0x100;
- ep1->rbptr = DPRAM + CPM_USB_RX1_BASE;
- ep1->tbptr = DPRAM + CPM_USB_TX1_BASE;
- ep1->tstate = 0;
-
- /* 21-24 */
- usbr->usep[0] = 0x0000;
- usbr->usep[1] = 0x1100;
- usbr->usep[2] = 0x2200;
- usbr->usep[3] = 0x3300;
-
- /* 25 */
- usbr->usmod = 0x06;
-
- /* 26 */
- usbr->usadr = 0x05;
-
- /* 27 */
- usbr->uscom = 0;
-
- /* 28 */
- usbr->usmod |= 0x01;
- udelay (1);
-
- /* 29-30 */
- usbr->uscom = 0x80;
- usbr->uscom = 0x81;
-
- /* Wait for the data packet to be transmitted */
- for (j = 0; j < TOUT_LOOP; j++) {
- if (tx[1].cbd_sc & (ushort) 0x8000)
- udelay (1);
- else
- break;
- }
-
- USB_EXPECT (j < TOUT_LOOP);
-
- USB_EXPECT (tx[0].cbd_sc == 0x3800);
- USB_EXPECT (tx[0].cbd_datlen == 3);
-
- USB_EXPECT (tx[1].cbd_sc == 0x3C80);
- USB_EXPECT (tx[1].cbd_datlen == 3);
-
- USB_EXPECT (rx[0].cbd_sc == 0x2C00);
- USB_EXPECT (rx[0].cbd_datlen == 5);
-
- USB_EXPECT (*(volatile int *) (dpram + CPM_USB_DR0_BASE) ==
- 0xABCD122B);
- USB_EXPECT (*(volatile char *) (dpram + CPM_USB_DR0_BASE + 4) == 0x42);
-
- res = 0;
- Done:
-
- return res;
-}
-
-#endif /* CONFIG_POST & CONFIG_SYS_POST_USB */
diff --git a/post/cpu/mpc8xx/watchdog.c b/post/cpu/mpc8xx/watchdog.c
deleted file mode 100644
index a070539b16f4107304e22f7bf9e6b7ddd07758e1..0000000000000000000000000000000000000000
--- a/post/cpu/mpc8xx/watchdog.c
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-/*
- * Watchdog test
- *
- * The test verifies the watchdog timer operation.
- * On the first iteration, the test routine disables interrupts and
- * makes a 10-second delay. If the system does not reboot during this delay,
- * the watchdog timer is not operational and the test fails. If the system
- * reboots, on the second iteration the test routine reports a success.
- */
-
-#include <post.h>
-#include <watchdog.h>
-
-#if CONFIG_POST & CONFIG_SYS_POST_WATCHDOG
-
-static ulong gettbl (void)
-{
- ulong r;
-
- asm ("mftbl %0":"=r" (r));
-
- return r;
-}
-
-int watchdog_post_test (int flags)
-{
- if (flags & POST_REBOOT) {
- /* Test passed */
-
- return 0;
- } else {
- /* 10-second delay */
- int ints = disable_interrupts ();
- ulong base = gettbl ();
- ulong clk = get_tbclk ();
-
- while ((gettbl () - base) / 10 < clk);
-
- if (ints)
- enable_interrupts ();
-
- /*
- * If we have reached this point, the watchdog timer
- * does not work
- */
- return -1;
- }
-}
-
-#endif /* CONFIG_POST & CONFIG_SYS_POST_WATCHDOG */
diff --git a/post/tests.c b/post/tests.c
index d8ac54e7589c456bf1d1369c8ce50466c7ddce35..bc8e39805157da8431f82d84e5c63e0afdb1563c 100644
--- a/post/tests.c
+++ b/post/tests.c
@@ -180,18 +180,6 @@ struct post_test post_list[] =
CONFIG_SYS_POST_ETHER
},
#endif
-#if CONFIG_POST & CONFIG_SYS_POST_SPI
- {
- "SPI test",
- "spi",
- "This test verifies the SPI operation.",
- POST_RAM | POST_ALWAYS,
- &spi_post_test,
- NULL,
- NULL,
- CONFIG_SYS_POST_SPI
- },
-#endif
#if CONFIG_POST & CONFIG_SYS_POST_USB
{
"USB test",
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index 2126a88a039e9d2b96be73a10e491e6ea16e00d5..925f334794c8ecce750a67de98b5ca6f1602f76f 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -43,14 +43,6 @@ CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
CONFIG_83XX_PCICLK
CONFIG_83XX_PCI_STREAMING
CONFIG_88F5182
-CONFIG_8xx_CONS_NONE
-CONFIG_8xx_CONS_SCCx
-CONFIG_8xx_CONS_SMC1
-CONFIG_8xx_CONS_SMC2
-CONFIG_8xx_CONS_SMCx
-CONFIG_8xx_CPUCLK_DEFAULT
-CONFIG_8xx_GCLK_FREQ
-CONFIG_8xx_OSCLK
CONFIG_A003399_NOR_WORKAROUND
CONFIG_A008044_WORKAROUND
CONFIG_A3M071
@@ -809,8 +801,6 @@ CONFIG_ETHER_ON_FCC
CONFIG_ETHER_ON_FCC1
CONFIG_ETHER_ON_FCC2
CONFIG_ETHER_ON_FCC3
-CONFIG_ETHER_ON_FEC1
-CONFIG_ETHER_ON_FEC2
CONFIG_ETHER_ON_SCC
CONFIG_ETHPRIME
CONFIG_ETH_BUFSIZE
@@ -870,8 +860,6 @@ CONFIG_FEATURE_SH_APPLETS_ALWAYS_WIN
CONFIG_FEATURE_SH_EXTRA_QUIET
CONFIG_FEATURE_SH_FANCY_PROMPT
CONFIG_FEATURE_SH_STANDALONE_SHELL
-CONFIG_FEC1_PHY
-CONFIG_FEC2_PHY
CONFIG_FEC_10MBIT
CONFIG_FEC_AN_TIMEOUT
CONFIG_FEC_ENET
@@ -1278,8 +1266,6 @@ CONFIG_IBM_EMAC4_V4
CONFIG_ICACHE
CONFIG_ICON
CONFIG_ICS307_REFCLK_HZ
-CONFIG_IDE_8xx_DIRECT
-CONFIG_IDE_8xx_PCCARD
CONFIG_IDE_INIT_POSTRESET
CONFIG_IDE_LED
CONFIG_IDE_PCMCIA
@@ -1328,7 +1314,6 @@ CONFIG_IOMUX_LPSR
CONFIG_IOMUX_SHARE_CONF_REG
CONFIG_IOS
CONFIG_IO_TRACE
-CONFIG_IP86x
CONFIG_IPADDR
CONFIG_IPADDR1
CONFIG_IPADDR2
@@ -1351,7 +1336,6 @@ CONFIG_IS_ENABLED
CONFIG_IS_INVALID
CONFIG_IS_MODULE
CONFIG_IS_VALID
-CONFIG_IVMS8
CONFIG_JFFS2_CMDLINE
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
@@ -1387,7 +1371,6 @@ CONFIG_KIRKWOOD_RGMII_PAD_1V8
CONFIG_KIRKWOOD_SPI
CONFIG_KIRQ_EN
CONFIG_KM8321
-CONFIG_KM8XX
CONFIG_KMCOGE4
CONFIG_KMCOGE5NE
CONFIG_KMETER1
@@ -1689,7 +1672,6 @@ CONFIG_MPC555
CONFIG_MPC5xxx_FEC
CONFIG_MPC5xxx_FEC_MII10
CONFIG_MPC5xxx_FEC_MII100
-CONFIG_MPC823
CONFIG_MPC8247
CONFIG_MPC8255
CONFIG_MPC8272_FAMILY
@@ -1722,22 +1704,15 @@ CONFIG_MPC83XX_GPIO_1_INIT_DIRECTION
CONFIG_MPC83XX_GPIO_1_INIT_OPEN_DRAIN
CONFIG_MPC83XX_GPIO_1_INIT_VALUE
CONFIG_MPC83XX_PCI2
-CONFIG_MPC850
-CONFIG_MPC855
-CONFIG_MPC857
CONFIG_MPC85XX_FEC
CONFIG_MPC85XX_FEC_NAME
CONFIG_MPC85XX_PCI2
CONFIG_MPC860
CONFIG_MPC860T
-CONFIG_MPC862
CONFIG_MPC866
CONFIG_MPC866_FAMILY
-CONFIG_MPC86x
CONFIG_MPC885
-CONFIG_MPC885_FAMILY
CONFIG_MPC8XXX_SPI
-CONFIG_MPC8XX_LCD
CONFIG_MPC8xxx_DISABLE_BPTR
CONFIG_MPLL_FREQ
CONFIG_MPR2
@@ -2285,7 +2260,6 @@ CONFIG_RTC_MC146818
CONFIG_RTC_MCFRRTC
CONFIG_RTC_MCP79411
CONFIG_RTC_MPC5200
-CONFIG_RTC_MPC8xx
CONFIG_RTC_MV
CONFIG_RTC_MXS
CONFIG_RTC_PCF8563
@@ -2733,9 +2707,6 @@ CONFIG_SYS_64BIT_VSPRINTF
CONFIG_SYS_66MHZ
CONFIG_SYS_8313ERDB_BROKEN_PMC
CONFIG_SYS_83XX_DDR_USES_CS0
-CONFIG_SYS_8XX_XIN
-CONFIG_SYS_8xx_CPUCLK_MAX
-CONFIG_SYS_8xx_CPUCLK_MIN
CONFIG_SYS_ACE_BASE
CONFIG_SYS_ACE_BASE_PHYS_H
CONFIG_SYS_ACE_BASE_PHYS_L
@@ -2871,7 +2842,6 @@ CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_BR8_PRELIM
CONFIG_SYS_BR9_PRELIM
-CONFIG_SYS_BRGCLK_PRESCALE
CONFIG_SYS_BRIGHTNESS
CONFIG_SYS_BUSCLK
CONFIG_SYS_CACHELINE_SHIFT
@@ -3332,7 +3302,6 @@ CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
CONFIG_SYS_DEFAULT_MBAR
CONFIG_SYS_DEFAULT_VIDEO_MODE
CONFIG_SYS_DEF_EEPROM_ADDR
-CONFIG_SYS_DELAYED_ICACHE
CONFIG_SYS_DER
CONFIG_SYS_DEVICE_NULLDEV
CONFIG_SYS_DFU_DATA_BUF_SIZE
@@ -4123,7 +4092,6 @@ CONFIG_SYS_I2C_BUS_MAX
CONFIG_SYS_I2C_CLK_OFFSET
CONFIG_SYS_I2C_DAVINCI
CONFIG_SYS_I2C_DIRECT_BUS
-CONFIG_SYS_I2C_DPMEM_OFFSET
CONFIG_SYS_I2C_DSPIC_2_ADDR
CONFIG_SYS_I2C_DSPIC_ADDR
CONFIG_SYS_I2C_DSPIC_IO_ADDR
@@ -4286,7 +4254,6 @@ CONFIG_SYS_I2C_SPEED3
CONFIG_SYS_I2C_TCA642X_ADDR
CONFIG_SYS_I2C_TCA642X_BUS_NUM
CONFIG_SYS_I2C_TEGRA
-CONFIG_SYS_I2C_UCODE_PATCH
CONFIG_SYS_I2C_W83782G_ADDR
CONFIG_SYS_I2C_ZYNQ
CONFIG_SYS_I2C_ZYNQ_SLAVE
@@ -4613,7 +4580,6 @@ CONFIG_SYS_MDIO_BASE_ADDR
CONFIG_SYS_MDIO_PIN
CONFIG_SYS_MDMRS_VAL
CONFIG_SYS_MDREFR_VAL
-CONFIG_SYS_MEASURE_CPUCLK
CONFIG_SYS_MECR_VAL
CONFIG_SYS_MEMAC_LITTLE_ENDIAN
CONFIG_SYS_MEMORY_BASE
@@ -5413,7 +5379,6 @@ CONFIG_SYS_POST_MEM_REGIONS
CONFIG_SYS_POST_OCM
CONFIG_SYS_POST_PREREL
CONFIG_SYS_POST_RTC
-CONFIG_SYS_POST_SPI
CONFIG_SYS_POST_SPR
CONFIG_SYS_POST_SYSMON
CONFIG_SYS_POST_UART
@@ -5435,7 +5400,6 @@ CONFIG_SYS_PSDMR
CONFIG_SYS_PSDPAR
CONFIG_SYS_PSRT
CONFIG_SYS_PSSR_VAL
-CONFIG_SYS_PTA_PER_CLK
CONFIG_SYS_PTCPAR
CONFIG_SYS_PTDPAR
CONFIG_SYS_PTL2_BITS
@@ -5494,12 +5458,10 @@ CONFIG_SYS_RIO_MEM_BUS
CONFIG_SYS_RIO_MEM_PHYS
CONFIG_SYS_RIO_MEM_SIZE
CONFIG_SYS_RIO_MEM_VIRT
-CONFIG_SYS_RMDS
CONFIG_SYS_RMR
CONFIG_SYS_ROM_BASE
CONFIG_SYS_ROOTPATH
CONFIG_SYS_RSTC_RMR_VAL
-CONFIG_SYS_RTCSC
CONFIG_SYS_RTC_BUS_NUM
CONFIG_SYS_RTC_CNT
CONFIG_SYS_RTC_OSCILLATOR
@@ -5556,7 +5518,6 @@ CONFIG_SYS_SDIO_BASE0
CONFIG_SYS_SDIO_BASE1
CONFIG_SYS_SDIO_BASE2
CONFIG_SYS_SDIO_BASE3
-CONFIG_SYS_SDMR
CONFIG_SYS_SDRAM
CONFIG_SYS_SDRAM0_CFG0
CONFIG_SYS_SDRAM0_CLKTR
@@ -5671,7 +5632,6 @@ CONFIG_SYS_SDRC_MR_VAL5
CONFIG_SYS_SDRC_TR_VAL
CONFIG_SYS_SDRC_TR_VAL1
CONFIG_SYS_SDRC_TR_VAL2
-CONFIG_SYS_SDSR
CONFIG_SYS_SD_VOLTAGE
CONFIG_SYS_SEC_MON_ADDR
CONFIG_SYS_SEC_MON_OFFSET
@@ -5710,14 +5670,10 @@ CONFIG_SYS_SMC0_MODE0_VAL
CONFIG_SYS_SMC0_PULSE0_VAL
CONFIG_SYS_SMC0_SETUP0_VAL
CONFIG_SYS_SMC_CSR0_VAL
-CONFIG_SYS_SMC_DPMEM_OFFSET
CONFIG_SYS_SMC_RXBUFLEN
-CONFIG_SYS_SMC_UCODE_PATCH
CONFIG_SYS_SMI_BASE
CONFIG_SYS_SPANSION_BASE
CONFIG_SYS_SPANSION_BOOT
-CONFIG_SYS_SPC1920_PLD_BASE
-CONFIG_SYS_SPC1920_SMC1_CLK4
CONFIG_SYS_SPCR_OPT
CONFIG_SYS_SPCR_TSEC1EP
CONFIG_SYS_SPCR_TSEC2EP
@@ -5739,7 +5695,6 @@ CONFIG_SYS_SPI_CLK
CONFIG_SYS_SPI_CS_ACT
CONFIG_SYS_SPI_CS_BASE
CONFIG_SYS_SPI_CS_USED
-CONFIG_SYS_SPI_DPMEM_OFFSET
CONFIG_SYS_SPI_FLASH_U_BOOT_DST
CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS
CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE
@@ -5749,7 +5704,6 @@ CONFIG_SYS_SPI_KERNEL_OFFS
CONFIG_SYS_SPI_MXC_WAIT
CONFIG_SYS_SPI_RTC_DEVID
CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
-CONFIG_SYS_SPI_UCODE_PATCH
CONFIG_SYS_SPI_U_BOOT_OFFS
CONFIG_SYS_SPI_U_BOOT_SIZE
CONFIG_SYS_SPI_WRITE_TOUT
@@ -6050,10 +6004,6 @@ CONFIG_TQM860L
CONFIG_TQM860M
CONFIG_TQM862L
CONFIG_TQM862M
-CONFIG_TQM866M
-CONFIG_TQM885D
-CONFIG_TQM8xxL
-CONFIG_TQM8xxM
CONFIG_TRACE
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY