diff --git a/arch/arm/mach-rockchip/rk3368-board-spl.c b/arch/arm/mach-rockchip/rk3368-board-spl.c
index 691db417571e39f25b0785944920b90c630ff68d..cabf34448643ef232288833321a0bbe218a803f6 100644
--- a/arch/arm/mach-rockchip/rk3368-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3368-board-spl.c
@@ -19,23 +19,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-/*
- * The ARMv8 generic timer uses the STIMER1 as its clock-source.
- * Set up the STIMER1 to free-running (i.e. auto-reload) to start
- * the generic timer counting (if we don't do this, udelay will not
- * work and block indefinitively).
- */
-static void secure_timer_init(void)
-{
-	struct rk_timer * const stimer1 =
-		(struct rk_timer * const)0xff830020;
-	const u32 TIMER_EN = BIT(0);
-
-	writel(~0u, &stimer1->timer_load_count0);
-	writel(~0u, &stimer1->timer_load_count1);
-	writel(TIMER_EN, &stimer1->timer_ctrl_reg);
-}
-
 void board_debug_uart_init(void)
 {
 }
@@ -52,9 +35,6 @@ void board_init_f(ulong dummy)
 		hang();
 	}
 
-	/* Make sure the ARMv8 generic timer counts */
-	secure_timer_init();
-
 	/* Set up our preloader console */
 	ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
 	if (ret) {
diff --git a/arch/arm/mach-rockchip/rk3368-board-tpl.c b/arch/arm/mach-rockchip/rk3368-board-tpl.c
index 1a69da2bd84d5ca7ec79066d4e86dedca96c72c8..b3e6ffa781b0e92a3ec304bd9a8e09a797c7980d 100644
--- a/arch/arm/mach-rockchip/rk3368-board-tpl.c
+++ b/arch/arm/mach-rockchip/rk3368-board-tpl.c
@@ -20,23 +20,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-/*
- * The ARMv8 generic timer uses the STIMER1 as its clock-source.
- * Set up the STIMER1 to free-running (i.e. auto-reload) to start
- * the generic timer counting (if we don't do this, udelay will not
- * work and block indefinitively).
- */
-static void secure_timer_init(void)
-{
-	struct rk_timer * const stimer1 =
-		(struct rk_timer * const)0xff830020;
-	const u32 TIMER_EN = BIT(0);
-
-	writel(~0u, &stimer1->timer_load_count0);
-	writel(~0u, &stimer1->timer_load_count1);
-	writel(TIMER_EN, &stimer1->timer_ctrl_reg);
-}
-
 /*
  * The SPL (and also the full U-Boot stage on the RK3368) will run in
  * secure mode (i.e. EL3) and an ATF will eventually be booted before
@@ -153,8 +136,6 @@ void board_init_f(ulong dummy)
 		hang();
 	}
 
-	/* Make sure the ARMv8 generic timer counts */
-	secure_timer_init();
 	/* Reset security, so we can use DMA in the MMC drivers */
 	sgrf_init();